Lopi Berkshire User manual

Featuring the Burner

• Direct Vent Freestanding Stove

• Natural Gas or Propane

• Vent Horizontally or Vertically

• Standard Residential

• Mobile Home Approved

Tested and Listed by

OMNI-Test Laboratories, Inc.

Beaverton, Oregon

Report # 028-S-28-5

ANSI Z21.88

WARNING: If the information in these instructions is not followed exactly, a fire or explosion

may result causing property damage, personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

This appliance may be installed in an aftermarket permanently located, manufactured home

(USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases unless a certified kit is used.

Berkshire Owner's Manual

Installer: After installation give this manual to the home-owner and

explain operation of this heater.

Mukilteo, WA 98275

2Introduction

Travis Industries 100-01187_000 4070219

Introduction

We welcome you as a new owner of a Lopi Berkshire stove. In purchasing a Berkshire you have joined

the growing ranks of concerned individuals whose selection of an energy system reflects both a

concern for the environment and aesthetics. The Berkshire is one of the finest home heaters the

world over. This manual will explain the installation, operation, and maintenance of this stove. Please

familiarize yourself with the Owner's Manual before operating your heater and save the manual for

future reference. Included are helpful hints and suggestions that will make the operation and

maintenance of your new stove an easier and more enjoyable experience. We offer our continual

support and guidance to help you achieve the maximum benefit and enjoyment from your heater.

Important Information

No other Berkshire Stove has the same serial number

as yours. The serial number is on the listing plate

chained to the gas control valve.

This serial number will be needed in case you require

service of any type.

Model: Lopi Berkshire Stove

Serial Number:

Purchase Date:

Purchased From:

traviswarranty.com

Or, mail your warranty card to:

Travis Industries House of Fire

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

Save Your Bill of Sale.

To receive full warranty coverage, you

will need to show evidence of the date

you purchased your heater. Do not

mail your Bill of Sale to us.

We suggest that you attach your Bill of

Sale to this page so that you will have

all the information you need in one

place should the need for service or

information occur.

Table of Contents 3

Travis Industries 100-01187_000 4070219

Introduction

Introduction & Important Information................2

Safety Precautions

Safety Precautions......................................4

Features & Specifications

Features ....................................................6

Installation Options......................................6

Heating Specifications..................................6

Dimensions.................................................6

Installation

Installation Warning......................................7

Packing List................................................7

Additional Items Required for Installation..........7

Installation Overview....................................7

Installation Hints..........................................8

Stove Clearances ........................................8

Mobile Home Requirements............................8

Heater Placement Requirements.....................9

Floor Protection Requirements........................9

Gas Line Installation.....................................10

Vent Requirements.......................................11

Approved Vent Configurations........................12

Restrictor Position...................................12

Measuring Vent Lengths...........................12

Vertical Term. with 0, 2, or 4 45° Elbows .......13

Hor. Term. with 1 90° Elbow........................14

Hor. Term. with 2 Elbows...........................15

Hor. Term. with 3 Elbows...........................16

Vertical Term. with 2 90° Elbows .................17

Vertical Term. with 3 Elbows......................18

Vent Termination Requirements ......................19

Class A Chimney Conversion..........................20

Masonry Chimney Conversion ........................21

Finalizing the Installation

Pilot Adjustment ..........................................22

Air Shutter Adjustment..................................23

Glass Removal (& installation)........................24

Log Installation............................................26

Operation

Before You Begin.........................................28

Location of Controls .....................................28

Starting The Pilot .........................................29

Starting the Stove for the First Time.................30

Turning the Stove On and Off .........................30

Adjusting the Flame Height.............................30

Adjusting the Blower Speed (optional) ..............31

Normal Operating Sounds..............................31

Normal Operating Odors................................31

Maintenance

Maintaining Your Stove’s Appearance..............32

Yearly Service Procedure..............................32

Troubleshooting Table...................................33

How this Stove Works...................................34

What Turns the Main Burners On and Off......34

What Prevents Gas Buildup.......................34

Wiring Diagram ............................................35

Replacement Parts List.................................35

Safety Label

Safety (Listing) Label....................................36

Warranty

Warranty....................................................37

Optional Equipment

LP Conversion Kit ........................................38

Blower .......................................................41

Accent Light ...............................................43

Cast or Stone Inserts....................................46

Index

Index.........................................................48

4Safety Precautions

Travis Industries 100-01187_000 4070219

• IF YOU SMELL GAS:

* Do not light any appliance

* Extinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire

department

• This unit must be installed by a qualified installer to prevent the

possibility of an explosion. Your dealer will know the requirements in

your area and can inform you of those people considered qualified.

The room heater should be inspected before use and at least annually

by a qualified service person. More frequent cleaning may be

required due to excessive lint from carpeting, bedding material, etc.

• The instructions in this manual must be strictly adhered to. Do not use makeshift

methods or compromise in the installation. Improper installation will void the warranty

and safety listing.

For LPG only | Pout 11” W.C.

Look for this label:

If the label is present, the

heater is equipped for LP

(propane). If the label is

absent, the heater is equipped

for NG (natural gas).

•This heater is either approved for natural

gas (NG) or for propane (LP or LPG).

Burning the incorrect fuel will void the

warranty and safety listing and may cause

an extreme safety hazard. Direct

questions about the type of fuel used to

your dealer. Check for the label shown to

the right.

•Contact your local building

officials to obtain a permit

and information on any

installation restrictions or

inspection requirements in

your area. Notify your

insurance company of this

heater as well.

•If the flame becomes sooty,

dark orange in color, or

extremely tall, do not

operate the heater. Call

your dealer and arrange for

proper servicing.

•It is imperative that control

compartments, screens, or

circulating air passageways

of the heater be kept clean

and free of obstructions.

These areas provide the air

necessary for safe

operation. ?•Do not operate the heater if

it is not operating properly in

any fashion or if you are

uncertain. Call your dealer

for a full explanation of your

heater and what to expect.

Gas

•Do not store or use gasoline

or other flammable liquids in

the vicinity of this heater.

AAAA

•Do not use this appliance if

any part has been under

water. Immediately call a

qualified service technician

to inspect the appliance and

to replace any part of the

control system and any gas

control which has been

under water.

Safety Precautions 5

Travis Industries 100-01187_000 4070219

•Do not place clothing or

other flammable items on or

near the heater. Because

this heater can be controlled

by a thermostat there is a

possibility of the heater

turning on and igniting any

items placed on or near it.

•Light the heater using the

built-in piezo igniter. Do not

use matches or any other

external device to light your

heater.

•Never remove, replace,

modify or substitute any part

of the heater unless

•The viewing glass should be

opened only for lighting the

pilot or conducting service.

Do not operate with cracked,

broken, or removed glass.

•Any safety screen or guard

removed for servicing must

be replaced prior to

operating the heater.

instructions are given in this

manual. All other work must

be done by a trained

technician. Don't modify or

replace orifices.

•Allow the heater to cool

before carrying out any

maintenance or cleaning.

•Operate the heater

according to the instructions

included in this manual.

•If the main burners do not

start correctly turn the gas

off at the gas control valve

and call your dealer for

service.

•The pilot flame must contact

the thermopile and

thermocouple (see the

illustration to the left). If it

does not, turn the gas

control valve to "OFF" and

call your dealer.

•This unit is not for use with

solid fuel

•Do not place anything inside

the firebox (except the

included fiber logs).

•If the fiber logs become

damaged, replace with

Travis Industries log set.

This

Manual

•Do not throw this manual

away. This manual has

important operating and

maintenance instructions

that you will need at a later

time. Always follow the

instructions in this manual.

•Children and adults should

be alerted to the hazards of

high surface temperature

and should stay away to

avoid burns or clothing

ignition. Young children

should be supervised when

they are in the same room as

the heater.

• Plug the heater into a

120V grounded electrical

outlet. Do not remove the

grounding plug.

• Don’t route the electrical

cord in front of, over, or

under the heater

•Instruct everyone in the

house how to shut gas off to

the appliance and at the gas

main shutoff valve. The gas

main shutoff valve is usually

next to the gas meter or

propane tank and requires a

wrench to shut off.

•Travis Industries, Inc.

grants no warranty,

implied or stated, for

the installation or

maintenance of your

heater, and assumes

no responsibility of any

consequential

damage(s).

6Specifications

Travis Industries 100-01187_000 4070219

Features:

- Ember Fyre™ Burner for "Wood Fire" Look

- Works During Power Outages (millivolt system)

- High Efficiency

- Optional Thermostat or Remote Control

- Optional Blower for Quicker Heat Distribution

- Convenient Operating Controls

- Variable-Rate Heat Output

- Low Maintenance

Installation Options:

- Freestanding Stove

- Horizontal or Vertical Vent

- Residential or Mobile Home

- Straight or Corner Placement

- Bedroom Approved

Heating Specifications:

Approximate Heating Capacity (in square feet)*.....................500 - 1,500 with Blower, 500 to 1,200 Without

Maximum BTU Input Per Hour..............................................31,000

Output from Low to High (in BTU’s per hour).........................16,608 to 26,815

Steady State Efficiency (without blower)**............................Up to 86.5 %

AFUE (without blower)........................................................Up to 72.8 %

* Heating capacity will vary depending on the home’s floor plan, degree of insulation, and the outside temperature.

** Efficiency rating is a product of thermal efficiency rating determined under continuous operation independent of

installed system.

Dimensions & Weight:

Weight: 215 Lbs.

NOTE:

Measure side, corner,

and back clearances

from the stove top.

19" 4-7/8" 26-3/4" The flue collar protrudes

7/8" above the stove top

28-1/8"

16-1/8"

Electrical Specifications (for optional blower)

Electrical Rating.........................................................115 Volts, 1.3 Amps, 60 Hz (150 watts on high)

Fuel:

This heater is shipped in natural gas (NG) configuration but may be converted to propane (LP) using

the included LP conversion kit. The sticker on top of the gas control valve will verify the correct fuel.

Installation (for qualified installers only) 7

Travis Industries 100-01187_000 4070219

Installation Warnings:

! Failure to follow all of the requirements may result in property damage, bodily

injury, or even death.

! This heater must be installed by a qualified installer who has gone through a

training program for the installation of direct vent gas appliances.

! This appliance must be installed in accordance with all local codes, if any; if not,

follow ANSI Z223.1 and NFPA 54(88).

! In Manufactured or Mobile Homes must conform with Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the Standard for Manufactured Home Installations,

ANSI/NCSBCS A225.1. This appliance may be installed in Manufactured Housing

only after the home is site located.

! This stove is designed to operate on natural gas or propane (LP).

! All exhaust gases must be vented outside the structure of the living-area.

Combustion air is drawn from outside the living-area structure.

! Notify your insurance company before hooking up this stove.

! The requirements listed below are divided into sections. All requirements must be

met simultaneously. The order of installation is not rigid – the qualified installer

should follow the procedure best suited for the installation.

Packing List

• Propane Conversion Kit

• Log Set

• Touch-Up Paint

• 4 Screws & Clips (Fyrestone only) for stone inserts

• Cover Plate with Knob (for the Aroma-Therapy option)

Additional Items Required

• Vent (see “Venting Requirements” for details)

• Gas Line Equipment (shutoff valve, pipe, etc.)

Additional Accessories Required

• Enameled Units are shipped without the top and side

inserts - see "Stone or Cast Insert Installation" on page ??

Installation Overview

See "Vent

Requirements"

See "Floor

Protection

Requirements"

See "Gas Line

Installation"

AAAAAAAAAAAAAAAAAAA

AAAAAAAAAAAAAAAAA

See

"Clearances"

8Installation (for qualified installers only)

Travis Industries 100-01187_000 4070219

Installation Hints:

• If converting to LP, convert the appliance prior to installation.

• The blower is easiest to install prior to installation. Because the blower is located near the gas inlet

location, the gas inlet must be routing around the blower position.

• Install the logs last - they are fragile.

• When determining the location of the stove, locate the wall studs (for horizontal penetrations) and

ceiling trusses (for vertical penetrations). You may wish to adjust the stove position slightly to ensure

the vent does not intersect with a framing member.

• Fumes and smoke from the paint curing and oil burning off the steel may occur the first time you start

this heater. This is normal. We recommend you open windows to vent the room.

Stove Clearances

10" Min.

5" Min.

Straight Installations Corner Installations

With this clearance, the vent is

centered 15-3/4" from the

wall.

5" Min.

AAA

With this clearance the

vent is centered 7-1/8"

from the back wall, 23-1/2"

from the side wall.

45°

Mobile Home Requirements

•When the stove is installed in a mobile home, it must be bolted to the floor and the appliance

grounded (use the optional blower with a grounded circuit or other suitable grounding method -

current ANSI/NFPA 70).

Installation (for qualified installers only) 9

Travis Industries 100-01187_000 4070219

Heater Placement Requirements

•Heater must be installed on a level surface capable of supporting the heater and vent.

•Due to high temperatures, the appliance should be located out of traffic and away from furniture

and draperies.

•When placed in a location where the floor to ceiling height is under 7 feet, the installation is

considered an alcove and must meet the following requirements:

•The alcove floor to ceiling height must be at least 58”tall

•The alcove must not be more than 45”deep before the ceiling returns to 7’

•The alcove must be at least 46-3/4”wide

•The heater must not be placed so the vents below or above the door, along the sides of heater, or

along the back of the heater can become blocked.

•This heater may be placed in a bedroom. Please be aware of the large amount of heat this

appliance produces when determining a location.

Floor Protection Requirements

•When the stove is installed directly on carpeting, vinyl or other combustible material other

than wood flooring or a high pressure laminate wood floor, the stove must be installed on

a metal or wood protection panel extending the full width and depth of the heater

(Minimum 26-3/4”wide by 19”deep).

Make sure these rubber tipped

bolts on each leg contact the floor

(they dampen any noise that may

transmit through the hearth). Do

not adjust with weight on the legs,

the rubber tips may tear.

10 Installation (for qualified installers only)

Travis Industries 100-01187_000 4070219

Gas Line Installation

MASSACHUSETTS INSTALLATIONS - WARNING:

THIS PRODUCT MUST BE INSTALLED BY A LICENSED PLUMBER OR GAS FITTER WHEN INSTALLED WITHIN THE

COMMONWEALTH OF MASSACHUSETTS.

OTHER MASSACHUSETTS CODE REQUIREMENTS:

• Flexible connector must not be longer than 36 inches.

• Shutoff valve must be a “T”handle gas cock.

• Only direct vent sealed combustion products are approved for bedrooms or bathrooms.

• Fireplace dampers must be removed or welded in the open position prior to the installation of a fireplace insert or gas log.

• A carbon monoxide (CO) detector is required in the same room as the appliance.

!The gas line must be installed in accordance with all local codes, if any; if not, follow current ANSI

Z223.1 or NFPA 54.

!The heater and gas control valve must be disconnected from the gas supply piping during any

pressure testing of that system at test pressures in excess of 1/2 psig (3.45 kPA). For pressures

under 1/2 psig (3.45 kPA), isolate the gas supply piping by closing the manual shutoff valve.

NOTE: The gas inlet may pass close

to the blower - we suggest

you install the blower first or

provide adequate clearance.

•This heater is designed for natural gas

but can be converted to propane. Check

the sticker on top of the gas control valve

to verify the correct fuel is used (see

page 4).

•Leak test all gas line joints and the gas

control valve prior to and after starting the

heater.

•A manual shutoff valve is required for

installation (it must be located within 3’of

the heater).

T-Handle gas cocks are required in

Massachusetts in compliance with code

248CMR.

•The location of the gas inlet (3/8" FPT) is

shown to the right.

Centerline

6-1/2"

10-1/4"

5-3/4"

Gas Inlet Pressure

•With the heater off, the inlet pressure must meet the requirements listed in the table below

•If the pressure is not sufficient, make sure the piping used is large enough and the total gas load

for the residence does not exceed the amount supplied.

•The supply regulator (the regulator that attaches directly to the residence inlet or to the propane

tank) should supply gas at the suggested input pressure listed below. Contact the local gas

supplier if the regulator is at an improper pressure.

Standard Input Pressure

Natural Gas 7”W.C. (1.74 Kpa)

Propane 13”W.C. (3.23 Kpa)

Installation (for qualified installers only) 11

Travis Industries 100-01187 4040621

Vent Requirements

•The vent must maintain the required 1" clearance to combustible materials to prevent a fire. Do not fill

air spaces with insulation.

•The gas appliance and vent system must be vented directly to the outside of the building, and never

be attached to a chimney serving a separate solid fuel or gas-burning appliance. Each direct vent gas

appliance must use it's own separate vent system.

• When the vent passes through a

wall a wall thimble is required.

When the vent passes through a

ceiling a support box or firestop is

required. When the vent passes

through the roof, a roof flashing

and storm collar are required.

Follow the instructions provided

with the vent for installing these

items.

NOTE: Wall thimbles may have

different dimensions than what is

required by this heater.

•Failure to adjust the air shutter properly

may lead to improper combustion

which can create a safety hazard.

Consult your dealer or installer if you

suspect an improperly adjusted air

shutter.

•This heater has been tested at

altitudes ranging from sea level to

8,000 feet (2,400 M). In this

testing we have found that the

heater, with its standard orifice,

burns correctly with just an air

shutter adjustment.

Use a firestop whenever

passing through a ceiling

Vertical Termination NOTE:

always use the "high-wind"

version (if applicable)

Use a roof flashing and storm collar

whenever passing through the roof

Use a support box

on exposed vent

Vertical Vent

Requirements

Use a thimble when

passing through a wall

Horizontal Termination

Maintain a minimum 1"

clearance from vent to any

combustible.

Minimum

Framing for wall

thimble

Horizontal Vent

Requirements

Maintain a minimum 1"

clearance from vent to

any combustible

•Use of of the following 6-5/8" diameter co-axial gas direct vent systems:

Manuafacturer Series

Simpson Dura-Vent Model GS

Selkirk Hearth Products Direct-Temp

American Metal Products Ameri-Vent

Metal-Fab Inc. Direct-Vent with 4DHT or 4DVT Cap

NOTE

: Always use the high-wind cap for the type of vent you are using (if applicable)

•Slide the vent sections together and turn 1/4 turn until the sections lock in place.

•Screws are not required to secure the vent. However, three screws may be used to

secure vent sections together if desired.

•High temperature sealant is recommended at the appliance starter section connection

(use high-temperature silicone or Mill-Pac®).

•If disassembly is required, at time of re-assembly check to see if the vent creates a tight fit.

If it does not, apply high temperature sealant to the joints of the affected sections.

•Horizontal sections require a 1/4" rise every 12" of travel

•Horizontal sections require non-combustible support every three feet (e.g.: plumbing

tape)

12 Installation (for qualified installers only)

Travis Industries 100-01187_000 4070219

Approved Vent Configurations

Restrictor Position

•A restrictor is built into the appliance to control the flow rate of exhaust gases. This ensures proper

flames for the wide variety of vent configurations. Depending upon the vent configuration, you may

be required to adjust the restrictor position. The charts for approved vent configurations describe

which position the vent restrictor must be in.

Lift the stove top off the stove

and place it aside.

To Adjust the Restrictor

To Access the Restrictor

NOTE:

The restrictor is

shipped in

position #1.

This restrictor is

in position # 6

Lift the cotter pin out.

Slide the restrictor

adjustment rod in.

Replace the cotter pin

through the correct

hole on the restrictor

adjustment rod.

Restrictor

Positions

# 2

# 4

# 6

# 3

# 5

# 1

Measuring Vent Lengths

Vent

Horizontal

Run

Vent Horizontal Run is

measured from the start of

the horizontal section to the

end of the termination.

Vent Height is calculated to

the top of the vent on

horizontal terminations and

to the top of the termination

on vertical terminations.

Vent

Height Vertical Elbow

NOTE:

When a horizontal elbow (90°or 45°) is

used, horizontal length is the sum of the

two lengths (H1 + H2).

Horizontal

Elbow

Vertical Elbow

Installation (for qualified installers only) 13

Travis Industries 100-01187_000 4070219

Vertical Termination with Zero, Two, or Four 45° Elbows

•The termination must fall

within the shaded area

shown in the chart. Use

the indicated restrictor

position.

•If using offsets, use the

table below to calculate the

vertical rise and horizontal

offset

Offset

Length

Horizontal

Offset

Vertical

Rise

Offset Length Hor. Offset Vert. Rise

None 5”1’

1’Section 1’1’7”

2’Section 1’9”2’4”

3’Section 2’5”3’

4’Section 3’2”3’8”

4’+ 1’Section 3’9”4’4”

4’+ 2’Section 4’6”5’

4’+ 3’Section 5’2”5’9”

4’+ 4’Section 6’6’9”

AAAAAAAAAAAAAAAAAAA

5 feet

10 feet

15 feet

20 feet

25 feet

30 feet

0 feet

40' (max)

5 feet

0 feet

5 feet

10 feet

15 feet

20 feet

25 feet

30 feet

40' (max)

Restrictor

Position # 5

NOTE:

Restrictor positions are based

upon lab tests. The ideal

restrictor position may vary

slightly, especially when the

termination is near a

demarkation line.

Restrictor

Position # 6

10 feet

15 feet

20 feet

24 ' (max)

0 feet

5 feet

10 feet

15 feet

20 feet

24 ' (max)

35 feet35 feet

14 Installation (for qualified installers only)

Travis Industries 100-01187_000 4070219

Horizontal Termination with One 90° Elbow

•If using a Snorkel Termination (14”or 36”) add the snorkel height to the vertical height (snorkel

terminations are used primarily for basement installations).

•The termination must fall within the shaded area shown in the chart. Use the indicated restrictor

position.

AAAAAAAAAAAAAAAAAAAAA

5 feet

10 feet

15 feet

19' (max)

0 feet

5 feet

0 feet

5 feet

10 feet

15 feet

Restrictor Position # 5

NOTE:

Restrictor positions are based

upon lab tests. The ideal

restrictor position may vary

slightly, especially when the

termination is near a

demarkation line.

Restrictor

Position # 1

10 feet

15 feet

20 feet

24 ' (max)

0 feet

5 feet

10 feet

15 feet

20 feet

24 ' (max)

19' (max)

NOTE:

Horizontal sections require a 1/4"

rise every 12" of travel.

NATURAL GAS: Min. 2' Section Required

PROPANE (LP): Min. 3' Section Required

Installation (for qualified installers only) 15

Travis Industries 100-01187_000 4070219

Horizontal Termination with Two Elbows

(one 90° vertical and one 90° or 45° horizontal elbow)

•If using a Snorkel Termination (14”or 36”) add the snorkel height to the vertical height (snorkel

terminations are used primarily for basement installations).

•The termination must fall within the shaded area shown in the chart. Use the indicated restrictor

position.

AAAAAAAAAAAAAAAAAAAAA

5 feet

10 feet

15 feet

19' (max)

0 feet

5 feet

0 feet

5 feet

10 feet

15 feet

Restrictor

Position # 5

NOTE:

Restrictor positions are based upon lab

tests. The ideal restrictor position may vary

slightly, especially when the termination is

near a demarkation line.

Restrictor

Position # 1

10 feet

15 feet

20 feet

24 ' (max)

0 feet

5 feet

10 feet

15 feet

20 feet

24 ' (max)

19' (max)

NOTE:

Horizontal sections require a 1/4"

rise every 12" of travel.

This is considered a horizontal

elbow (it does not matter

whether it turns right or left).

It may be a 90°or 45°elbow.

This is considered a

vertical elbows

Horizontal length (max. 24') is calculated

by adding both lengths of horizontal run

(Horizontal Length = H1 + H2).

NATURAL GAS: Min. 2' Section Required

PROPANE (LP): Min. 3' Section Required

16 Installation (for qualified installers only)

Travis Industries 100-01187_000 4070219

Horizontal Termination with Three 90° Elbows (all vertical)

•The termination must fall within the shaded area shown in the chart. Use the indicated restrictor

position.

AAAAAAAAAAAAAAAAAAAA

5 feet

10' (min)

15 feet

21' (max)

0 feet

5 feet

0 feet

5 feet

10' (min)

15 feet

Restrictor

Position # 5

NOTE:

Restrictor positions are based

upon lab tests. The ideal restrictor

position may vary slightly,

especially when the termination is

near a demarkation line.

Restrictor

Position # 1

10 feet

15 feet

20 feet

24 ' (max)

0 feet

5 feet

10 feet

15 feet

20 feet

24 ' (max)

21' (max)

NOTE:

Horizontal sections require a 1/4"

rise every 12" of travel.

This is a horizontal elbow -

NOT ALLOWED FOR THIS

VENT CONFIGURATION

These are

vertical elbows.

Installation (for qualified installers only) 17

Travis Industries 100-01187_000 4070219

Vertical Termination with Two 90° Elbows

•The termination must fall within the shaded area shown in the chart. Use the indicated restrictor

position.

AAAAAAAAAAAAAAAAAA

5 feet

10' (min)

15 feet

20 feet

25 feet

30 feet

0 feet

40' (max)

5 feet

0 feet

5 feet

10' (min)

15 feet

20 feet

25 feet

30 feet

40' (max)

Restrictor

Position # 5

NOTE:

Restrictor positions are

based upon lab tests. The

ideal restrictor position may

vary slightly, especially

when the termination is near

a demarkation line.

Restrictor

Position # 6

10 feet

15 feet

20 feet

24 ' (max)

0 feet

5 feet

10 feet

15 feet

20 feet

24 ' (max)

35 feet35 feet

Restrictor

Position # 1

NOTE:

Horizontal sections require a 1/4"

rise every 12" of travel.

This is a horizontal elbow -

NOT ALLOWED FOR THIS

VENT CONFIGURATION

These are

vertical elbows.

18 Installation (for qualified installers only)

Travis Industries 100-01187_000 4070219

Vertical Termination with Three 90° Elbows

(Two 90° Vertical and One 45° or 90° Horizontal Elbow)

•The termination must fall within the shaded area shown in the chart. Use the indicated restrictor

position.

AAAAAAAAAAAAAAAAAA

5 feet

10' (min)

15 feet

20 feet

25 feet

30 feet

0 feet

40' (max)

5 feet

0 feet

5 feet

10' (min)

15 feet

20 feet

25 feet

30 feet

40' (max)

Restrictor

Position # 5

NOTE:

Restrictor positions are based

upon lab tests. The ideal

restrictor position may vary

slightly, especially when the

termination is near a demarkation

line.

10 feet

15 feet

20 feet

24 ' (max)

0 feet

5 feet

10 feet

15 feet

20 feet

24 ' (max)

35 feet35 feet

Restrictor

Position # 1

NOTE:

Horizontal sections require a

1/4" rise every 12" of travel.

This is considered a horizontal

elbow (it does not matter

whether it turns right or left).

It may be a 45°or 90°elbow.

This is considered a

vertical elbow

Horizontal length (max. 24') is calculated

by adding both lengths of horizontal run

(Horizontal Length = H1 + H2).

H2 This is considered a

vertical elbow

Installation (for qualified installers only) 19

Travis Industries 100-01187_000 4070219

Vent Termination Requirements (see illustration below)

! Venting terminals shall not be recessed into a wall or siding.

A Minimum 9" clearance from any door or window

B Minimum 12" above any grade, veranda, porch, deck or balcony

C Minimum 3-3/8" from outside corner walls

NOTE: Clearance in accordance with local installation codes and the requirements

of the gas supplier.

D Minimum 12" from inside corner walls

NOTE: Clearance in accordance with local installation codes and the requirements

of the gas supplier.

11”Min.

6”Min.

Roof

Surface

Roof

Eaves

E Minimum 11" clearance below unventilated soffits or roof surfaces

Minimum 18" clearance below ventilated soffits

Minimum 6" clearance below roof eaves

NOTE: Vinyl surfaces require 24"

NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.

F Minimum 12" clearance below a veranda, porch, deck or balcony

NOTE: Permitted only if veranda, porch, deck, or balcony is fully open on a minumum of two sides beneath the floor.

NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.

G Minimum 48" clearance from any adjacent building

H Minimum 84" clearance above any grade when adjacent to public walkways or driveways

NOTE: may not be used over a walkway or driveway shared by an adjacent building

I Minimum 48" clearance from any mechanical air supply inlet

J Minimum 36" clearance above and 48”below and to the sides of non-mechanical air supply inlet

K Minimum 36" from the area above the meter/regulator (vent outlet)

NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.

L Minimum 36" from the meter/regulator (vent outlet)

NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.

M Minimum 12”above the roof line (for vertical terminations)

N Minimum 24”horizontal clearance to any surface (such as an exterior wall) –for vertical terminations

NOTE: Measure clearances to the nearest edge of the exhaust hood.

•Use the vinyl siding standoff (#1250) when installing on an exterior with vinyl siding.

•Vent termination must not be located where it will become plugged by snow or other material

20 Installation (for qualified installers only)

Travis Industries 100-01187_000 4070219

Class A Chimney Conversion Kit

Simpson Duravent provides a conversion kit for those wishing to use an existing wood stove chimney

to vent this direct vent stove. The illustration below gives an overview of this type of installation. See

the instructions included with the kit for details.

! Do not exceed the maximum vertical rise. The restrictor position should be set to the position that

most closely resembles the vent configuration (see "Approved Vent Configurations" for details).

NOTE: because this installation utilizes non-standard vent, the restrictor position may vary. Carefully

monitor the burn characteristics to verify correct restrictor position.

! The conversion kit does not work on interior masonry chimneys.

Chimney Conversion Kit A (# 931)

Metalbestos 6" I.D.

Security Chimneys 6" I.D.

Jackes-Evans 6" I.D.

Hart & Cooley 6" I.D.

Pro-Jet 6" I.D.

Chimney Conversion Kit B (# 932)

Simpson Dura-Vent 6" I.D.

Air-Jet 6" I.D.

Metal-Fab 6" and 7" I.D.

Amer. Metals 6" & 7" I.D.

Metalbestos 7" and 8" I.D.

Jackes-Evans 7" and 8" I.D.

Hart & Cooley 7" and 8" I.D.

Pro-Jet 7" and 8" I.D.

Security Chimneys 8" I.D.

Chimney Conversion Kit C (# 933)

Simpson Dura-Vent 7" and 8" I.D.

American Metals 8" I.D.

Air-Jet 8" I.D.

Metal-Fab 8" I.D.

American Metals 8" I.D.

Each Kit Contains:

Retro Connector

Retro Vertical Top

Additional Required Equipment:

4" Flex (#711 or U.L. 1777)

Termination (#991)

Co-Axial Sections

Type A Chimney

Simpson Duravent Direct

Vent Pipe Sections

(use adjustable section)

Screw the Retro

Vertical Top to the

Flex Pipe

Retro Vertical Top

(screw to chimney)

Screw the Retro

Connector to the

Flex Pipe

Retro Connector

(screw to chimney)

4" (100 mm)

Aluminum Flex

Pipe

Cut the Flex Pipe to

the chimney height

plus 3" (75 mm)

Other manuals for Berkshire

Table of contents

Popular Wood Stove manuals by other brands

Woodstock Soapstone

Woodstock Soapstone Keystone Assembly instructions

Golden Eagle

Golden Eagle ECONOMY SERIES 5040 Owner’s Instruction and Operation Manual

Drolet

Drolet LEGEND III owner's manual

SHILOH

SHILOH TR002B owner's manual

HearthStone

HearthStone Phoenix 8612 owner's manual

Nordpeis

Nordpeis Q-23FL - Powerstone user manual

Panadero

Panadero OSAKA Usage and maintenance instructions

Breckwell

Breckwell SP24 owner's manual

hergom

hergom SHELBURNE Instruction book

Regency Fireplace Products

Regency Fireplace Products Alterra F175B-1 Owners & installation manual

Superior Fireplaces

Superior Fireplaces WXS2016 Installation and operation manual

Osburn

Osburn 3300 Installation and operation manual

Nibe

Nibe Contura 690AG Style manual

Euroheat

Euroheat WIKING MIRO Range Operating and maintenance instructions

Travis Industries

Travis Industries Lopi 1750 Republic owner's manual

Quadra-Fire

Quadra-Fire 2100 Millennium owner's manual

Globe fire

Globe fire Neptune user manual

Enerzone

Enerzone SOLUTION 1.7 owner's manual