Lorex DV900 Series User manual

Package Contents
DV900_QSG_EN_R2
USB MouseEthernet CablePower Adapter HDMI Cable
4K Ultra HD Security DVR
Remote Control
Dimensions
Connect your cameras (not included) to your recorder.
DV900 Series
Quick Setup Guide
Physical setup of recorder and essential system settings
1 /2
Setting Up Your Recorder
Follow the steps below to complete physical setup of your recorder.
To set up your recorder:
STEP 1:
Connect cameras*
STEP 2:
Connect router*
STEP 3:
Connect mouse
STEP 5:
Connect power
STEP 1:
Connect cameras*
STEP 2:
Connect router*
STEP 4:
Connect monitor*
STEP 3:
Connect mouse
STEP 5:
Connect power
Connect the recorder to your router using the included Ethernet cable.
Connect the recorder to a monitor using the included HDMI cable or a VGA cable
(not included). The HDMI port supports up to 4K resolution, and VGA supports up to
1080p.
Connect the included mouse to a USB port on the recorder.
Use the included power adapter to connect the recorder to a nearby outlet. Turn the
recorder on using the power switch on the back panel.
12.8” / 325mm 10.0” / 255mm
2.2”
55mm
* Not included / sold separately.
NOTES:
• The extension cable must be a single stretch of cable between the recorder and camera.
You cannot connect multiple extension cables to each other.
• This guide covers connecting cameras to your security recorder only. For full instructions on
installing your cameras, please refer to your camera’s documentation at lorex.com.
NOTE: To receive automatic firmware updates and enable remote viewing with computer and
mobile apps, a high speed Internet connection is required (minimum 3.5Mbps upload speed).
All other system features can be used without an Internet connection.
OR
NOTE: To optimize picture quality, set the recorder’s video output to match the resolution of
your monitor.
8-channel configuration shown. 16 channel will have the respective number of video inputs.
For camera compatibility information, visit lorex.com/compatibility.
Overview of extra ports:
NOTE: For full instructions on using the extra ports, please refer to your security recorder’s
instruction manual at lorex.com.
Audio In/Out
Connect microphone / speaker*
RS485
Connect Pan-Tilt-Zoom (PTZ) cameras*
Back panels shown below are for illustration only. Your recorder’s back panel may
appear different, with all the same ports in different locations.
Copyright © 2019 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to modify product design,
specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.
Need Help?
Visit us online for up-to-date software
and complete instruction manuals
Click on the Downloads tab
4
Visit lorex.com
Search for the model
number of your product
Click on your product
in the search results
3
2
1
STEP 4:
Connect monitor*

DV900_QSG_EN_R2
Once you have completed the physical setup of your recorder,
follow the steps below to configure essential system settings.
Now that you have set up your recorder, see the following
reference sections to learn more about using your system.
STEP 1: Creating a New Password
When using your system for the first time, you will be prompted to create a new 6
character password.
To create a new password:
1. Connect your system according to the instructions on the front of this guide.
2. When the recorder turns on, create and confirm your new, secure password. This
password will be used to connect to your system from now on.
Record your password below and store in a secure place:
STEP 2: Firmware Update
This system features automatic firmware upgrades for enhanced functionality. It is
required to upgrade your system to the latest firmware version.
To upgrade firmware:
1. After startup, a notification will appear asking you to upgrade the firmware if a
newer version is available. Click OK to upgrade.
2. The system will download and install the firmware upgrade. Wait for the firmware
update to complete. The system may restart during the firmware upgrade process.
IMPORTANT: Do not power off the recorder or disconnect the power cable during
firmware installation.
STEP 3: Setting Date and Time
It is important to set the correct time to ensure accurate time stamps on recordings.
To set date and time:
1. In live view, right-click and click Main Menu.
2. Log in using the system user name (default: admin) and your new, secure password.
3. Click and select Setting.
4. Click General and select the Date & Time tab.
5. Click Apply to save changes.
a. Enter the current time and
select your time zone, and
click OK.
b. Check DST to enable auto
Daylight Savings Time
updates.
c. (Optional) Check NTP to
sync your system with an
Internet time server. Click
Manual Update to instantly
update the time.
NOTE: A constant Internet
connection is required to
use NTP.
a
b
c
1. LEFT-CLICK:
• During split-screen display mode: Click an individual channel
to view it in full-screen. Click again to return to the split-screen
display mode.
• While navigating menus: Click to open a menu option.
2. RIGHT-CLICK:
• During live view: Right-click anywhere on the screen to open
the Quick Menu.
• While navigating menus: Right-click to exit menus.
3. SCROLL WHEEL:
• During live view: Use the scroll wheel to zoom in / out.
NOTE: In live view, hover the mouse cursor over the top of the
screen to open the Navigation Bar. Move the mouse cursor away
from the top of the screen to close the Navigation Bar.
To quickly open a window that displays vital system information such as device ID,
model number, firmware version, and IP address:
•Press the ENTER button on the front panel.
OR
•Right-click to open the Quick Menu and click Info. If prompted, enter the system user
name (default: admin) and your new, secure password.
Reference: Using the Quick Menu
Right-click anywhere on the live viewing screen to open the Quick Menu.
b
a
c
d
e
f
g
h
i
a. Select camera/live display view.
b. Control PTZ cameras (not included).
c. Adjust camera color and image settings.
d. View system information.
e. Start/stop sequence mode.
f. Disable current audible warning.
g. Search and playback recordings.
h. Open manual recording controls.
i. Open Main Menu.
Reference: Using the Mouse
Reference: Quick Access to System Information
Search through and play video recordings from the hard drive.
To search for and play back recordings:
1. From live view, right-click and then click Playback.
2. Log in using the system user name (default: admin) and your new, secure password.
3. Configure the following:
Reference: Playback and Search
a. Use the calendar on the right to select
the date to playback.
b. Use the drop-down menus to select the
channels you would like to playback.
Click the display options ( )
to playback multiple channels
simultaneously.
c. Click inside the video bar to select
the playback time. Playback starts
immediately at the selected time.
b
a
c
Back up recordings from the hard drive to a USB flash drive (not included).
To back up recordings:
1. Insert a USB flash drive (not included) into a free USB port on the recorder.
2. From live view, right-click and then click Main Menu.
3. Log in using the system user name (default: admin) and your new, secure password.
4. Click , then click BACKUP.
5. Configure the following:
Reference: Backup
a. Select the type and quality of
recordings to search for.
b. Select the channel(s) to search
by.
c. Select a start and end time for
your search.
d. Choose a file format for your
backed up files.
e. Click Add to see recordings
that match your search.
f. Check boxes next to recordings
you want to back up, then
click Start. You may also click
Onekey Backup to back up all
files that match your search.
ab
cde
f
1 2
3
STEP 4: Configuring Deterrence Settings
1. In live view, right-click and click Main Menu.
2. Log in using the system user name (default:
admin) and your new, secure password.
3. Click and select Setting.
4. Click Event > Motion > Deterrence
(see Figure 1).
5. Select the channel of the deterrence camera to
configure next to Camera.
6. Click the Enable checkbox to enable automatic
warning light deterrence.
7. Click Setup next to Area to set the active area
for automatic deterrence:
To configure automatic deterrence using DVR:
Set preferences for the automatic warning light triggering on compatible Lorex deterrence
cameras. For a complete list of compatible deterrence cameras, see lorex.com/compatibility.
To activate deterrence features manually:
Figure 1: Deterrence Tab
Figure 2: Deterrence Active Area Example
10. Click Apply to save changes.
• Press and hold ESC on the front panel for
5 seconds. Warning lights and sirens will
be activated for all connected deterrence
cameras.
Press and hold for 5 seconds.
• From live display, hover near the top of
a channel to reveal the Mini Menu. Click
to activate warning light, or click
to activate siren.
8. Click Setup next to Schedule to set a schedule
during which automatic deterrence will be used:
• The camera image appears with a grid of green
boxes over top. The green area is the active area
for deterrence.
• Click or click-and-drag to add / remove boxes
from the active area.
• In Figure 2, only motion around the doorway will
trigger warning light.
• Right-click when finished.
• The default schedule is active during the night,
between 5pm and 7am.
• Right-click when finished.
9. Click Warning Light to set preferences for the warning light:
• Enter a time for the white light to be active up to 30 seconds.
• Select Warning Light for sustained light or Strobe for a flashing light.
• Click OK to save and exit.