Lorex CVC6999U User manual

QUICK START GUIDE
www.lorextechnology.com
Lorex Technologies Inc.
Copyright © 2010 Lorex Technologies Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product
design, specifications and prices, without notice and without incurring any obligation. E&OE
Cable Extension Options PROFESSIONAL LONG RANGE
OUTDOOR SECURITY CAMERA
Problem Solution
No Picture/Signal • Ensure your TV is on the correct input
channel. Common terms of an input channel:
INPUT, AV CHANNEL, LINE1, LINE2, AUX.
• If your camera is connected to a VCR/DVR,
ensure it is properly connected to your TV/
Monitor.
• Ensure connections are properly connected.
• Ensure all the camera power supply is
plugged in.
Picture is too bright • Ensure your camera isn’t pointed directly at a
source of light (e.g sun or spot light).
• Slide the sunshade (bullet cameras only)
forward to block excess light.
• Move your camera to a different location.
Picture is too dark • If using during the day, the camera may not
be getting enough light. Slide the sunshade
backwards to let in more light. Check the
brightness and contrast settings of the device
your camera connects to (TV/Monitor/DVR).
Night Vision is not
working
• The night vision activates when light levels
drop. The area may have too much light.
Picture is not clear • Check the camera lens for dirt, dust,
spiderwebs. Clean the lens with a soft, clean
cloth.
• Make sure that the cable run is within the
limitations specified in the section ' Cable
Extension Options'
Bright spot in video
when viewing camera
at night
• Night vision reflects when pointing a camera
to a window. Move the camera to a different
location.
BNC connection does
not connect to my TV
• Use a BNC to RCA adapter at the end of the
extension cable.
Troubleshooting
Option Cable Type
1Regular BNC
(supplied with
camera)
180ft / 55m 3
2'RG59' or 'Coax'
or ' Coaxial'
BNC (sold sepa-
rately)
300ft / 92m 5
3Lorex Universal
Cable
(sold separately)
300ft / 92m 3
Max. Cable
Run Distance
Max. # of
Extensions
MODEL: CVC6999U
English Version 1.0
Image Sensor 1/3” Color
Video Format / Pixels
Horizontal Resolution
Video Output
IR / Night Vision Range
Field of View (diagonal)
Minimum Illumination
Termination
NTSC: 768(H) x 494 (V)
540 TVL
Comp. 1.0 Vpp @ 75ohm
54 Degrees
0 LUX (IR LEDs on)
Video: BNC Female
Power: Barrel Female
Lens / Lens Mount 6.0 mm F1.4/ Fixed
Camera Specifications
Notes:
1. For optimal performance, consider using option 2 or 3. Preference for using
the same cable type for the entire distance.
2. Cable run recommendation based on typical camera power consumption (up
to 500mA). For specialty cameras with higher current consumption,
maximum cable run may be reduced. Consider providing power to the camera
at the camera side rather then at the end of the extension cable.
3. Indicators that your cable run may be too long:
• Video is permanently Black & White (even during day time)
• Video is distorted
Product Information
User Manuals
Quick Start Guides
Specification Sheets
Software Upgrades
Firmware Upgrades
www.lorextechnology.com
IT’S ALL ON THE WEB!
Extend the cable run for your camera up to 300ft or more
depending on the cable type used. See table below:
Operating Temp. 14°F ~ 122°F
(-10°C ~ 50°C)
Power Requirement 12V DC ±10%
Power Consumption 700mA or 8.4W max
Weight (with stand) 2.3 lbs. / 1.1 kg
56 IR LED / 130 ft. (40 m)
Environmental Rating IP 67
4.5"/ 115mm
11.5"/ 293mm
8.5"/ 216mm
All manuals and user guides at all-guides.com
all-guides.com

To install the camera:
1. Apply the mounting template sticker to the desired
mounting location (Figure 1).
2. Drill the holes according to the template, and push the
wall plugs into the holes.
3. Fasten the four screws 3/4 of the way.
4. Place bracket onto the screws (step 1) and gently lower
the bracket so that the screw locks the bracket in place
(step 2) (Figure 2).
5. Fasten the screws until they are secure.
6. Set the position and angle of the camera using the
provided Allen key.
7. Connect the extension cable to the camera:
ATTENTION - Ensure there is an opening in your mounting surface large
enough for the cables to pass through. If necessary, you can run the cables
through the pass-through ports at the top or bottom of the stand.
ATTENTION -Test all connections and ensure the camera is working
correctly prior to permanent installation.
Mounting Surface
Template Sticker
(Figure 1) (Figure 2)
Step 1
Step 2
Top pass-
through port
Bottom pass-
through port
Connect the BNC and
power connectors to the
camera.
Connect the BNC connector to the
video input of the monitor/DVR,
and connect the included power
connector to a power adapter.
Male power connector Female power connector
BNC Connector
To Camera To Monitor/ DVR
Contents
Features
• Ultra High Resolution image sensor produces 540 TV
lines of resolution
• Advanced noise reduction improves image quality and
recording storage efficiency
• Intelligent IR technology prevents image overexposure
• Capable of viewing images up to 130ft (40m)* away in
total darkness with IR night vision
• 6mm lens captures far away objects
• Cable pass-through wall mount bracket protects the
connection cable from vandalism
• IP67 rated housing for indoor / outdoor installations**
* IR illumination range under ideal conditions. Objects at or beyond this
range may be partially or completely obscured, depending on the camera
application.
** Not recommended for submersion in water
• Camera with cable pass through wall bracket
•Sunshade
• 66 ft. BNC/Power Extension Cable
• BNC to RCA Adapter
•12VDCPowerAdapter
• 4x Mounting screws
•4xWallplugs
•1xAllenkey
• 1x Mounting template
Installation Tips
• Point the camera towards a direction where there is
the least amount of obstructions (i.e. tree branches).
• Install the camera in a location that is difficult for
vandals to reach.
• Secure cabling so that it is not exposed or easily cut.
• Connect your system and cameras to a back-up power
supply. This ensures the system continues to record
during power outtages.
Installing The Camera
Warning / Caution Statements
1. Read this guide carefully and keep it for future reference.
2. Follow all instructions for safe use of the product.
3. Use the camera within given temperature, humidity and voltage levels noted
in Camera Specifications.
4. Do not disassemble the camera.
5. Do not point the camera directly towards the sun or a source of intense light.
6. Use only the supplied regulated power supply. Use of a non-regulated, non-
conforming power supply can damage this product and voids the warranty.
7. The supplied extension cable is rated for surface mounting only.
Cables for in-wall / floor-to-floor installations are sold separately.
Setup Diagram
DVR/CCTV MONITOR
Video IN
TV/VCR
Video IN
Attach the included BNC to RCA adapter to connect the
extension cable to RCA inputs (i.e. for a TV connection).
Accessories
BNC to RCA Adapter (included)
BNC to RCA Adapter
Connecting the Pin Connector
Pin Connector
BNC/Power connector
If the pin connection becomes loose, simply re-connect the pin
connector to the BNC/power connector. Line up the notch on
the pin connector with the arrow on the BNC/Power connector,
and push the connectors together. The pin connector goes in
one way only.
Notch
Arrow
All manuals and user guides at all-guides.com