Lorex SG6350 User manual

2.4 GHZ WIRELESS COLOR
CAMERA/RECEIVER SYSTEM
SG6350
FOR MORE INFORMATION
WWW.STRATEGICVISTA.COM
Before operating the system, please read this manual
thoroughly and retain it for future reference.
This product broadcasts over public airwaves and its
video and audio signals may be intercepted without
your consent.

Explanation of two Symbols
The lightning flash with arrowheadsymbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage“within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in
the literature accompanying the appliance.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON
THE BOTTOM OF THE SYSTEM.
!
WARNING: To prevent fire or shock hazard, do not expose this unit to
rain, water, or wet locations. Do not insert any metallic object
through the ventilation grills.
FCC CLASS B NOTICE
Note:
This equipment has been tested and found to comply with the limits For a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, (which can be determined by turning the equipment off
and on), the user is encouraged to try to correct the interference by one or more
of the following measures:
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
!
•Reorient or relocate the receiving antenna
•Connect the equipment into an outlet on a circuit different from that to which
other devices may be connected.
•Consult the dealer or an experienced radio or television technician for help.
i

SAFETY INSTRUCTIONS
IMPORTANT SAFEGUARDS
All the safety and operating instructions should be read before the
system is operated, and retained for future reference.
1. HEED WARNINGS -All warnings on the appliance and in the operating
instructions should be adhered to.
2. FOLLOW INSTRUCTIONS -All operating instructions should be
followed.
3. WATER AND MOISTURE -Do not use this video product near water –
for example, a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement.
4. POWER SOURCES -This product should be operated only from the type
of power source indicated on the marking label.
5. OVERLOADING -Do not overload outlets and extension cords, which
can result in a risk of fire or electric shock.
6. SERVICING -Do not attempt to service this product yourself. Opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing or repairs to qualified service personnel.
7. DAMAGE REQUIRING SERVICE -Unplug this product from the wall
outlet and refer servicing or repairs to qualified service personnel under
the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions.
e. If the product has been dropped or the cabinet has been damaged.
f. When the product exhibits a distinct change in performance.
8. REPLACEMENT PARTS -When replacement parts are required, be
sure the service technician has used replacement parts that are
specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
9. SAFETY CHECK -Upon completion of any service or repairs to this
video product, ask the service technician to perform safety checks to
determine if the video product is in proper operating condition.
10. An appliance and cart combination should be moved with care.
Do not place this equipment on an unstable cart, stand, or table.The
equipment may fall, causing serious injury to a child or adult, and
serious damage to the equipment. Wall or shelf mounting should
follow the manufacturer's instructions and should be done with
a mounting kit approved by the manufacturer.
ii

TABLE OF CONTENTS PAGE
iii
INTRODUCTION & FEATURES………………………………………
SYSTEM INCLUDES…………………………………………………..
CONTROLS AND FUNCTIONS
Wireless Camera….......…….......….……………………..……...
Wireless Receiver...……..............................……….……...……
INSTALLATION OF WIRELESS CAMERA………………………….
INSTALLATION OF WIRELESS RECEIVER
Operation with TV (Using RCA Cables)......……………….…....
Operation with TV (Using Coaxial Cable) ..............…..……......
SYSTEM OPERATION
Multiple Cameras / Auto Scanning…………………………………
Auto/Manual Options / Selectable Settings………………………
TROUBLE SHOOTING ..............................................………..…...
TECHNICAL SPECIFICATIONS ....................................................
CARE & MAINTENANCE……………………………..……………….
1
2
3
4
5
6
7
8
9
10
11
12

INTRODUCTION:
Thank you for purchasing the 2.4 GHz Wireless Color Camera &
Receiver System. This system turns your TV into a Video Security
System, providing instant protection in your home or office. Avoiding the
hassle of running wires, this system is easy to install and operate for
immediate applications.
The system is capable of connecting up to 4 cameras (additional
cameras sold separately) with the option to automatically scan between
locations.
To learn more about this 2.4GHz Wireless Camera & Receiver System
and our complete range of CCTV products, please visit our website at:
www.strategicvista.com
FEATURES:
•Turns your TV into a Video Security System
•Flexible –move camera from room to room
•Listen-in audio
•Camera has AC or battery option
•300 ft Wireless Transmission (open space)
•2.4 GHz Wireless Transmission
•Crystal clear Video and Stereo audio
•4 Channel Wireless System
•Record picture to any standard VCR
1

SYSTEM INCLUDES:
1 -2.4 GHz Color Wireless Camera
Owner’s Manual
Also includes:
2 –9V DC 500mA Adapters
2 –RCA Audio/Video Cables
1 –Coaxial Cable
2
1 -2.4 GHz Wireless Receiver

REAR VIEW
WIRELESS CAMERA
.
.
3
FRONT/ SIDE VIEW
CONTROLS & FUNCTIONS
7
8
1. Microphone –Built-in condenser microphone provides listen-in audio
capability from camera to TV
2. Lens –Color CMOS Image Sensor
3. Channel Selector Switch –Slide switch for channels 1-4
4. ON/OFF Power Switch –Controls power to the camera. Note: Please
ensure that you set the switch to the OFF position before plugging the
AC adapter into the unit
5. Battery Compartment –Optional 4 “AA” batteries (not included) can
be used to power the camera
6. Bracket –Metal bracket connects to camera for mounting to walls,
ceilings or table
7. DC IN Jack –Connects to the 9V DC (500mA) adapter.
8. 2.4GHz Antenna –High gain dipole antenna sends audio and video
signals to the receiver
26
4
3
15

WIRELESS RECEIVER
REAR VIEW
BOTTOMVIEW
9 10
5 6 7 8
1. Auto/Manual Button –Used to activate/deactivate auto sequencing
2. Channel Selector Button –Used to manually switch channels from 1-4
3. LED Channel Indicators –Indicator light shows selected channel
4. 2.4 GHz Antenna –High gain dipole antenna receives audio and video
signal from the wireless camera
5. Video Output Jack (Yellow) –RCA jack for video output connector
(when using RCA connector)
6. Audio Output Jacks L (White) & R (Red) –RCA jacks for audio
output connector (when using RCA connector)
7. RF Out Jack (To TV) –Connects the receiver to a TV using the supplied
coaxial cable. (alternative to RCA cable connection)
8. DC IN Jack –Connects to the power source of the receiver
9. ON/OFF Power Switch –Ensure this switch is set to OFF before
plugging the system into an electrical outlet
10.Channel 3/4 Selector Switch –Used to view picture on television when
using coaxial cable (preset to channel 3)
CONTROLS & FUNCTIONS
TOPVIEW
3
2
4
1
4

CONNECTING CAMERA TO AN AC OUTLET/ BATTERY POWER
INSTALLATION OF CAMERA
Ensure the Power Switch on the camera is turned OFF prior to
proceeding with the following steps.
NOTE
Electrical
Outlet
STEP 1:
5
To 9V Power
adapter
1. Attach the stand base to the wall or ceiling where you want to install the
camera. Locate a wall stud or ceiling, and secure the bracket using the
four supplied screws.
2. Attach the camera to the stand and firmly tighten the swivel.
3. Attach the camera with the stand to the stand base, and firmly tighten the
joint knob on the stand base.
4. Connect the supplied 9V 500mA DC adapter to the DC IN jack at the rear
of the camera, and plug it into an electrical outlet.
If you are using batteries to power the camera follow these steps:
1. Make sure that the power switch on the camera is turned “OFF”
2. Carefully slide open the battery compartment (bottom of camera)
3. Insert 4 “AA”batteries (not included) into the compartment noting the
polarity
Warning: to prevent damage to the unit, ensure the batteries are
aligned properly and battery types are not mixed.
4. Close the compartment and turn camera “ON”

CONNECTING THE RECEIVER TO A TV
INSTALLATION OF RECEIVER
STEP 2:
Ensure the Power Switch on the Receiver is turned OFF before
proceeding with the following steps.
NOTE
1. Place the wireless receiver near your television (or monitor).
2. Connect one end of the RCA cables to the Audio/Video output jacks at the
back of the Receiver. Plug the other end of RCA cables into the
Audio/Video In jacks on your television. Be sure the yellow, red and white
plugs match the yellow, red and white jacks on both the receiver and TV.
3. Connect one end of the supplied 9V 500 mA AC adapter into the DC IN
jack at the rear of the receiver; the other end into an electrical outlet. Turn
the receiver ON. The system is defaulted to channel 1.
4. Turn your T.V. to AX (Aux. Mode or TV/Video) to view the picture on your
second T.V.
5. Adjust the antenna on both the camera and receiver as necessary for
optimum viewing.
For optimum viewing reception you may need to change the
channels of both your camera and receiver to the same
channels between CH 1 –CH 4
NOTE
You have two options to connect the Receiver: A) Using RCA Cables
(see below), or B) Coaxial Cables, please refer to page 7 of this manual.
Back of Receiver Television
Electrical Outlet
A)
6

CONNECTING A RECEIVER TO A TV USING COAXIAL CABLES
INSTALLATION OF RECEIVER
B) Back of Receiver
Television
Electrical Outlet
Coaxial Cable (75 ohm)
Ensure the Power Switch on the Receiver is turned OFF prior to
proceeding with the following steps.
NOTE
1. Place the wireless receiver near your television (or monitor).
2. Connect one end of the coaxial cable to the back of the Receiver. Plug the
other end of the coaxial cable to the television.
3. Connect one end of the supplied 9V 500mA AC adapter into the DC IN jack
at the back of the receiver; the other end into an electrical outlet. Turn the
receiver ON. The system is defaulted to channel 1.
4. Search channels 1 through 4 by using Channel Selector Switch on the
Receiver and Camera.
5. Turn your TV to channel 3 to view the picture.
6. Adjust the antenna on both the camera and receiver as necessary for
optimum viewing.
For optimum viewing reception you may need to change the
channels of your camera and receiver to the same channels
between CH1 –CH 4
NOTE
Audio Video
7

SYSTEM OPERATION
CONNECTING MORE CAMERAS TO YOUR SYSTEM (MAX. OF 4)
When connecting additional cameras to this system, ensure the camera is
set to a different channel. Use the Auto/Manual button to navigate between
channels.
AUTO SCANNING -WHEN UTILIZING MORE THAN 1 CAMERA
The video security system provides you with the option to automatically
scan/switch between four camera locations. If you are utilizing less than four
cameras, you can also set the system to scan only within two or three
locations.
Setting Auto Scan to 2 or 3 camera locations:
1. Press and hold the Auto/Manual button for more than 2 seconds. All four
LED lights on the front of the receiver will turn ON. Releasing the
Auto/Manual button to remain in the four channel switching option.
2. Continue to press and hold the Auto/Manual button. The Channel 4 LED
button will turn off. The system is now set to scan between three camera
locations (Channel 1-3).
3. Continue to press and hold the Auto/Manual button. The Channel 3 LED
button will now be turned off. The system is now set to scan between two
camera locations (Channel 1-2).
4. Continue to press and hold the Auto/Manual button to return to the four
camera viewing option (all four LED lights will be illuminated).
8
The receiver will automatically do a self diagnostic when it is powered up to
determine how many cameras are connected. It will detect which channels are
receiving a video signal. To purchase additional wireless cameras, please visit
www.strategicvista.com

SYSTEM OPERATION
AUTO AND MANUAL VIEWING OPTIONS
This system is preset to the Manual mode. In Auto mode, the LED light will
turn ON.
To manually view a specific camera location, set the system to Manual and
press the Ch. Select key to view the desired camera location. Auto Mode is
used when more than 1 camera is connected to the system.
Set the Auto/Manual button to Auto Mode in order to have the system
automatically rotate between camera locations.
SELECTABLE DWELL SETTING
Dwell Setting is the time duration between each camera view in the auto
sequence mode
This system provides you with three selectable dwell options (2, 5 and 10
seconds) when the system is set to Auto Mode. This system is preset to a 2
second selection.
Changing Dwell Time
1. Press and hold the CH Select button. The LED button will turn on to
indicate that it is set to 2 seconds.
2. Continue to press and hold the CH Select button. The LED button will flash
at a one second interval to indicate that it is now set to the 5 second
setting.
3. Continue to press and hold the CH Select button. The LED button will flash
three times to indicate it is set to the 10 second setting.
9

FOR MORE INFORMATION, VISIT OUR WEBSITE AT:
www.strategicvista.com
TROUBLESHOOTING
If the system does not function properly, check the following points
before contacting the service center.
10
Causes & Remedies
Problems
-Adjust antenna direction-Adjust antenna directionPicture rolls and
jumps or
scrambledpicture
-Adjust brightness control on
TV/monitor
-Strong spot light in the
field of view
-Lighting source in the
field of view
Picture flickering
Picture too bright
or too dark
-Adjust antenna direction
-Improper channel 1-4
selection
-AC adapter not plugged in
-Power switch not turned
ON
Poor Reception
-AC adapter not plugged in
-Power switch not turned on
-TV or Monitor not turned on
-Improper A/V or coaxial
cable connection
-AC adapter not plugged in
-Power switch not turned
ON
No power
(no picture/sound)
Receiver/TransmitterCamera

TECHNICAL SPECIFICATIONS
Because our products are subject to continuous improvement, SVII and its subsidiaries reserve the right to modify
product design and specifications without notice and without incurring any obligation. E&OE
11
WIRELESS CAMERA
WIRELESS RECEIVER
Receiving frequency
Output level
Sensitivity
Antenna
Operating temperature
Power source
Dimensions
Weight
2.411GHz -2.473GHz (4CH)
1.0Vp-p(Video), 3.0Vp-p(Audio)
> 85 dBm
Dipole antenna
-14ºto + 122ºF or (-10ºC to + 50 ºC)
9V 500mA DC Adapter
5.25”(Diameter) x 1.5”(Height)
181 grams or 6.4 Oz
Image sensor
Lens
Scanning system
Scanning frequency
Sync. system
Resolution
Min. illuminations
Video Output
Gamma characteristics
Auto Iris
Microphone
Transmitting frequency
Modulation
RF out level
Video Output level
Antenna
Battery Option
Operating temperature
Power source
Dimensions
Weight
Color CMOS
3.6mm
2:1 interlace
15.734 KHz(H) 59.94Hz (V)
Internal Negative synchronization
380 Lines
2 Lux @ F2.0
1.0Vp-p/75 Ohm
r=0.45
Electrical Auto Iris
Shutter sensitivity :1/60-1/6,000
Electrronic Condenser
2.4 GHz-2.4835 GHz (4Ch)
FM
90dBu/V, 3m
1.0Vp-p/75 Ohm
Dipole
4 “AA”batteries, not included
-14ºto + 122ºF (-10ºC to + 50 ºC)
9V DC 500mA Adapter
6.2”(Length) x 2.2”(Diameter)
136 grams or 4.8 oz

CARE AND MAINTENANCE:
Please follow these instructions to ensure proper
care and maintenance of this system
Keep your monitor and camera dry. If it gets wet,
wipe it dry immediately.
Use and store your unit in normal temperature
environment. Extreme temperatures can shorten
the life of the electronic devices.
Handle the monitor carefully. Dropping it can cause
serious damage to the unit.
Occasionally clean the unit with a damp cloth to keep
it looking new. Do not use harsh chemicals, cleaning
solvents or strong detergents to clean the unit.
Keep the unit away from excessive dirt and dust. It
can cause premature wear of parts.
12