LORUS R23 Series User manual

INSTRUCTION MANUAL FOR
WATCH CALIBRE
Z025
THIS PRODUCT CONTAINS A BUTTON BATTERY
If swallowed or placed inside any part of the body, the battery can
cause severe or fatal injuries within 2 hours or less.
Button batteries are hazardous. Keep batteries out of reach of children.
If you think the battery may have been swallowed or placed inside any
part of the body, seek immediate medical attention. Contact the
Australian Poisons Information Centre immediately on 13 11 26
(New Zealand 0800 764 766) for 24 / 7 fast, expert advice.

■CHARACTERISTICS
1. Time/calendar display:Hour, minute,
second, month, date and day of the week
2. Time indication: 12-hour display format
with PM indicator and 24-hour display
format are available.
3. Stopwatch: The stopwatch can measure
up to 23 hours 59 minutes and 59 seconds
in 1/100-second increments. Split time
measurement is available.
4. Alarm: The alarm can be set to sound at
the designated time on a 24-hour basis.
5. Chime: The chime can be set to sound
every hour on the hour with a single beep.
6. Countdown timer: The countdown timer
can be set up to 23 hours 59 minutes and
59 seconds.
7. Illuminating light: The built-in electro-
luminescent (EL) light evenly illuminates
the display for easy viewing in darkness.
■BUTTONS AND DISPLAYS
NREZ025 10-2018
CAL. Z025 (R23 SERIES)
■HOW TO USE THE CHRONOGRAPH
Press Button D to go to the CHRONOGRAPH
mode. The CHRONOGRAPH mode indicator
appears on the display.
CHRONOGRAPH
mode indicator
Hour
Minute
Second
1/100 Second
* Measurement and release of split time can
be repeated by pressing Button C.
During the measurement, the outer second
markers keeps flashing.
Press Button D to return to the TIME/CALENDAR
mode.
Chronograph operation
Standard Measurement
Split Time Measurement
BC C B C
Start Split Reset
Split
Release Stop
BB
C
Start Stop Reset
Outer second
markers
■HOW TO USE TIMER
Press Button D twice to go to the TIMER mode.
The TIMER mode indicator appears on the
display.
1. Press Button A for 2 seconds. The second
digits start flashing.
2. Press Button B to set the second digits.
One digit (flashing) is advanced with each
press of Button B and reversed with each
press of Button C. The digits are advanced
or reversed quickly by keeping Button B
(advance) or C (reverse) pressed.
3. Press Button D to confirm the second
setting and move on to the minute setting.
The minute digits start flashing.
4. Press Button B or C to set the minute digits
in the same manner as the second setting.
5. Press Button D to confirm the minute
setting and move on to the hour setting.
The hour digits start flashing.
6. Press Button B or C to set the hour digits
in the same manner as the second and
minute setting.
7. Press Button A to complete the timer
setting.
TIMER
mode indicator
Current time
(Hour/Minute)
D
B
C
T I M E R T i m e
(hour & minute)
A
The time display format in either 12-hour
indication or in 24-hour indication can be
selected alternately by pressing Button B or
C. Under the 12-hour indication format, “PM”
mark appears in the afternoon, but no AM
mark appears in the morning. Under the 24-
hour indication format, no mark appears on
the display.
Hourly chime is OFF Hourly chime is ON
C
Choice of 12-Hour/24-Hour format
How to set the hourly chime
Current time
(Outer second
marker)
In the TIME/CALENDAR mode, press Button
C to turn ON or OFF the hourly chime.
Timer operation
BB
C
Start Stop Reset
1. Press Button B in the TIMER mode to start
the countdown timer.
2. Press Button B to stop the countdown timer.
3. To reset the timer, press Button C.
Press Button D to return to the TIME/CALENDAR mode.
D
B
C
P M
indicator
Hour
Day of the week
Chime
Date Minute
Second
Alarm
(START/STOP)
(SET/LIGHT)
(MODE)
(SPLIT/RESET)
Month
The display mode changes in the following order
by pressing Button D.
TIME CHRONOGRAPH TIMER
ALARM
SECOND TIME
ZONE
AB
C
D
D
■HOW TO SET THE TIME/CALENDAR
1. Press Button A for 2 seconds. The second
digits start flashing.
2. Selection of the digits to be adjusted
(flashing) is made in the following order by
pressing Button D.
SECONDS
DATE
12 / 2 4 - H O U R
FORMAT MONTH
MINUTES
HOURS
D
D
D
DD
D D
YEAR
3. One digit (flashing) is advanced with
each press of Button B, and reversed with
each press of Button C. The digits except
seconds are advanced or reversed quickly
by keeping Button B (advance) or C
(reverse) pressed.
A
Press Afor
2 seconds
Press Bor C
to set second
Press Bor C
to set hour
Press Bor C
to set
minute
Press Bor C
to set
year
Press Bor C
to set month
Press Bor C
to set date
Press Bor C
to set 12/24 H format
4. After all the adjustments are completed,
press Button A to return to the TIME/CALEN-
DAR mode.
Second setting
Press Button B in accordance
with a time signal. The second
digits are reset to “00” and
start counting immediately.
When the second digits count
any number from “30” to “59”
and Button B is pressed, one
minute is added and the
seconds are immediately reset
to “00.”
D D
D
D
D D
D
A
B
C
TIME/CALENDAR
Mode TIMER Mode
Press D
Twice
Press Bor C
to set minute
Press A for
2 seconds
AB
C
D
D A
D
Press Bor C
to set second
Press Bor C
to set hour
Press A to
complete setting
A
D
LORUS Z025_800.indd 1 2018/06/08 9:45

Press D
3 times Press Bor C
to set hour
Press Afor
2 seconds
Press Bor C
to set minute
Press Bor C
to set time zone
Alarm OFF Alarm ON
Note: The alarm can be set
only in one time zone.
The alarm sounds for 20 seconds at the
designated time. To stop it manually while
sounding, press any Button.
In the ALARM mode, with each press of Button
B, the alarm can be turned ON or OFF. When the
alarm is turned on, the ALARM mark appears
on the Display.
Press Button D to return to the TIME/CALENDAR
mode.
■HOW TO SET SECOND TIME ZONE
Press Button D four times to go to the SECOND
TIME ZONE. The SECOND TIME ZONE indicator
appears on the display.
1. Press Button A for 2 seconds. The hour digits
start flashing.
2. Press Button B to set the hour digits. One
digit (flashing) is advanced with each
press of Button B and reversed with each
press of Button C. The digits are advanced
or reversed quickly by keeping Button B
(advance) or C (reverse) pressed.
3. Press Button D to confirm the hour setting
and move on to the minute setting. The
minute digits start flashing.
4. Press Button B to set the minute digits. The
minute digits are increased in 30-minute
increments.
5. After all the adjustments are completed,
press Button A to confirm the time zone
setting.
Press Button D to return to the TIME/CALENDAR
mode.
■HOW TO USE EL BACKLIGHT
In any mode press Button A to illuminate the
display for about 3 seconds.
Note:
1. The backlight of the watch employs an elec-
tro-luminescent (EL) light, which tends to
lose illuminating power after very long use.
2. The illumination provided by backlight may
be hard to see when viewed under direct
sunlight.
The miniature battery CR2032, which powers
your watch should last approximately 4 years.
However, because it is inserted at the factory,
the actual life of the battery once in your
possession may be less than the specified
period.
Be sure to replace the battery to prevent any
possible malfunction as soon as it runs down.
To replace the battery we recommend taking
the watch to a local watch repair shop.
Note:If the alarm is used for more than 20
seconds a day and/or the illuminating
light for more than 6 seconds a day,
the battery life may be less than the
specified period.
■BATTERY CHANGE
Caution:
• Leather Band
• A leather band is susceptible to
discoloration and deterioration from
moisture, sweat and direct sunlight.
• Wipe off moisture and sweat as soon as
possible by gently blotting them up with
a dry cloth.
• Do not expose the watch to direct
sunlight for a long time.
• Please take care when wearing a watch
with light-colored band, as dirt is likely to
show up.
• Refrain from wearing a leather band
watch other than Aqua Free bands while
bathing, swimming, and when working
with water even if the watch itself is
water-resistant enforced for daily use(10-
BAR/20-BAR water resistant).
• Plastic band
• As for material characteristics, the band
is easily dirtied, and may be stained and
discolored. Wipe off dirt with a wet cloth
or cleaning tissue.
• Unlike bands of other materials, cracks
may result in the band being cut. Take
care not to damage the band with an
edged tool.
• ALLERGIC REACTION
Because the case and band touch the skin
directly, it is important to clean them regularly. If
not, shirt sleeves may be stained and those with
delicate skin may develop a rash. Please wear
the watch with some play to avoid any possible
allergic reaction. If you develop a rash on your
wrist, stop wearing and consult a physician.
• MAGNETISM
Your watch will not be affected by magnetism
generated by household electric appliances.
• SHOCKS AND VIBRATIONS
Your watch may be worn for normal sports
activities, but be careful not to drop it or hit it
on hard surfaces.
• TEMPERATURE
Your watch is pre-adjusted so that constant
accuracy may be insured at normal tempera-
ture.
■SERVICE
When your LORUS watch requires repair
or servicing, please see the enclosed
WARRANTY/GUARANTEE.
Printed in China
■HOW TO SET ALARM TIME
ALARM
mode indicator
Alarm time
zone
T1 or T2
A L A R M T i m e
(hour & minute)
Press Button D three times to go to the ALARM
mode. The ALARM mode indicator appears
on the display.
1. Press Button A for 2 seconds. The hour digits
start flashing.
2. Press Button B to set the hour digits. One
digit (flashing) is advanced with each
press of Button B and reversed with each
press of Button C. The digits are advanced
or reversed quickly by keeping Button B
(advance) or C (reverse) pressed.
3. Press Button D to confirm the hour setting
and move on to the minute setting. The
minute digits start flashing.
4. Press Button B or C to set the minute digits
in the same manner as the hour setting.
5. Press Button D to confirm the minute setting
and move on to the time zone setting.
6. Press Button B or C to select the time zone.
7. Press Button A to complete the alarm
setting.
SECOND TIME ZONE
mode indicator
Hour/Minute/
Second
Press A to
complete
setting
B
■CARE OF YOUR LORUS WATCH
• BATTERY
Do not expose the old battery to fire or
recharge it. Keep it at a place beyond the
reach of children. If a child swallows it, consult
a doctor immediately.
• WATER RESISTANT
Condition
of use Accidental
contact with
water, such
as splashes
and rain
Swimming
and taking
a shower
Skin
diving
Scuba
diving
Indication
on the dial/
case back
No
Indication
* If your watch is 200 M/20 BAR, 100 M/10
BAR or 50 M/5 BAR water resistant, it is so
indicated on the dial/case back.
•
Do not operate the buttons when the watch is wet.
• If the watch is exposed to salt water, rinse it in
fresh water and then wipe it thoroughly dry.
NO NO NO
YES
YES
YES NO NO
YES YES NO
NO NO NO
YES
WATER
RESISTANT
WATER
RESISTANT
(50M/5 BAR )
WATER
RESISTANT
100M/10 BAR
or above
(
NO
(
CAUTION
AB
C
D
How to turn ON or OFF the alarm
How to stop the alarm while sounding
Press
Afor
2 seconds
Press A to complete
setting
AB
C
D
D A
D
D
A
D A
D
D
D
Press D
4 times
Press Bor C
to set hour
Press Bor C
to set minute
A
D
B
C
ALARM Mode
AB
CD
2nd TIME ZONE Mode
TIME/CALENDAR
Mode
TIME/CALENDAR
Mode
LORUS Z025_800.indd 2 2018/06/08 9:45