LUCCI AIRFUSION AIRLIE ECO SERIES User manual

AIRLIE-V1.0
CEILING FAN MANUAL
INSTALLATION
OPERATION
MAINTENANCE
WARRANTY INFORMATION
LUCCI
AIRFUSION AIRLIE ECO SERIES
E27 LAMP HOLDER
CEILING FANS
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

2
CONGRATULATIONS, as you have just chosen a quality ceiling fan.
The information contained in the following pages has been prepared to ensure you of trouble-free operation of your
ceiling fan.
1. To ensure the success of the installation be sure to read the instructions and study the diagrams thoroughly.
2. For your safety, all electrical connection and disconnection must be performed by a licensed electrician.
3. All electrical work should only be undertaken after disconnection of the power by removing fuses or turning off
the circuit breaker to ensure all pole isolation of the electrical supply. If you are in any doubt the services of a
qualified electrician should be sought to ensure that all work is carried out in accordance with the local
regulations, current good practice and other national and local electrical codes.
4. Make sure that your installation location will not allow the rotating fan blades to come into contact with any
object and that there is a minimum clearance of 30cm from the blade tip to the wall or nearest object. Please
note that the bigger this clearance is the better the airflow from your fan will be. Ensure the blades are mounted
at a minimum height of 2.1 meters from the floor when the fan is installed.
5. The fixing point for the fan must be able to support a weight of at least 30kg. If you are mounting the fan to a
ceiling junction box, the box and it’s fixing must be able to support the moving weight of the fan and must not
twist or work loose.
6. The fan must be earthed.
7. Do not connect the fan motor to a dimmer switch. This may give an unsatisfactory performance (motor hum)
and cause damage to the motor. Only use the supplied wall controller.
8. It is not recommended that ceiling fans and gas appliances be operated in the same room at the same time.
9. The fan must be turned off and stopped completely before reversing the fan direction. This will prevent any
damage to the motor of the unit or controller (if installed).
10. Do not insert anything into the fan blades while the fan is operating, as this may cause person injury, damage
the blades, and upset the balance of the unit causing the unit to wobble.
11. After the fan is completely installed make sure that all connections are secured and tightened to prevent any
problems.
12. Because of the fans natural movement, some connections may loosen. Check the support connections,
brackets and blade attachments twice a year to make sure they are all secured. If they are loose, tighten with a
screwdriver.
Note: The important safeguards and instructions given in this manual are not meant to cover all possible conditions
and situations that may occur. It must be understood that common sense, caution and care are factors, which
cannot be built into any product. The persons caring for and using the unit must supply these factors.
For installation advice, or in the unlikely event of damaged or missing parts please consult a licensed electrician.
CONGRATULATIONS ON YOUR CHOICE
SAFETY PRECAUTIONS

3
IMPORTANT NOTES
FAN
CONTROL
Your warranty will be void if a solid-state dimmer type fan controller or other band
wall controller is used. ONLY use the wall controller supplied. With these
controllers there is a strong possibility that the ceiling fan motor will produce an
unpleasant load humming noise.
FAN
INSTALLATION
Under our warranty terms, this ceiling fan must be installed by a licensed
electrician. Improperly installed ceiling fans can be dangerous and expensive to
repair. This will void the warranty too. This fan is designed for indoor use only.
Mounting the fan where it is subject to water or moisture can be dangerous and
also void the warranty.
FAULT
FINDER
Always check the “Trouble Shooting Checklist” included in this booklet before
reporting a fault. Unnecessary calls are inconvenient for all and can attract a
service charge.
MECHANICAL NOISE MAY BE NOTICED ON INSTALLATION-ALLOW AT LEAST 8
HOURS SETTLING-IN PERIOD. SOME FANS WOBBLE MORE THAN
OTHERS—EVEN IN THE SAME MODEL, IT DOES NOT MEAN THE FAN IS FAULTY.
WARNING
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
The fan must be installed so that the blades are at least 2.1 meters above the floor.
The important safeguards and instruction appearing in this manual are not meant
to cover all possible conditions and situation that may occur. It must be
understood that common sense, caution and care are factors, which cannot be
built into any product. These factors must be supplied by the person(s) caring for
and operating the unit.

4
Unpack your ceiling fan carefully. Remove all parts and hardware. Place fan motor on a cloth or soft surface to
avoid damaging the finish.
Do not lay motor housing on its side as the decorative housing may become bent or damaged.
Verify that all parts are present before starting assembly.
Check the packaging carefully for missing parts.
Examine all parts. You should have the following:
Fig.1
AIRLIE FAN WITH LIGHT
AIRLIE FAN WITHOUT LIGHT
1.
Blades x 4
1.
Blades x 4
2.
Pre-assembled Fan motor, down rod, and canopy
x 1
2.
Pre-assembled Fan motor, down rod, and canopy
x 1
3.
Glass shade x 1
3.
Hanger Bracket x 1
4.
Hanger Bracket x 1
4.
Flat washers for blade screw x 13
5.
Flat washers for blade screw x 13
5.
Blade screws x 13
6.
Blade screws x 13
6.
Screws x 2
7.
Screws x 2
7.
Wooden screws for mounting bracket x 2
8.
Wooden screws for mounting bracket x 2
8.
Spring washers x2
9.
Spring washers x2
9.
Flat washers x 2
10.
Flat washers x 2
10.
Balancing kits x 1 set
11.
Balancing kits x 1 set
11.
Wall controller x 1 set
12.
Wall controller x 1 set
12.
Bottom cover plate x 1
BEFORE INSTALLATION

5
NOTE: Unlike most ceiling fans, you must attach the blades to the motor housing BEFORE mounting the
motor to the ceiling. When installing more than one fan, ensure that the blades sets are not mixed up as
each set is dynamically balanced.
The AIRLIE SERIES ceiling fan are now packaged with the motor, down rod and canopy cover
pre-assembled. Before installation, please check to ensure all screws and nuts are re-tightened as they may
become loose during transportation.
TOOLS REQUIRED
- Phillips head screw driver
- Flat head screw driver
- Pair of pliers
- Step ladder
- Wire cutter
- Wiring, supply cable as required by AS/NZS 3000 wiring code.
1. The ceiling fan must be installed in a location so that the blades are at least 2.1 meters above the floor, and
300mm spacing from the tip of the blade to the nearest objects or walls.
2. Secure the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 30KG, with
two long screws provided. Ensure at least 30mm of the screw is threaded into the support. Fig 2.
NOTE: Ensure the mains power supplies are switched OFF during installation.
NOTE: The bracket screw provided is for use with wooden structure only. For structures other than wood,
the appropriate screw type MUST be used.
INSTALLATION INSTRUCTIONS
INSTALLING THE FAN

6
3. Remove the two screws from the covering plate on top of the motor housing (Fig. 4), and remove the plate.
Fig 4.
4. Insert the blade through the slots around the motor. Align the blade with the three holes, and secure the three
screws through the opening exposed when the covering plate was removed. If the holes do not align, the blade is
upside down. The blade is designed to fit snugly; the screws should be vertical with the blade. Tighten all blade
screws evenly and securely to ensure quiet, wobble free operation of the fan. Repeat this process for all blades.
Replace the covering plate on top of the motor housing. Fig.4.
5. Carefully lift the fan and seat the down rod ball assembly into the spacing allocated in the mounting bracket and
lock the ball into place. Fig. 5
Fig.5
6. Insert and secure the light bulbs (Max. 15W CFL Spiral only, not included) into the ES sockets as shown in Fig.6.
NOTE: FOR FAN MODELS WITHOUT LIGHT, IGNORE THIS INSTALLATION PROCESS.
7. Carefully place the glass shade cover over the lamp and twist clockwise to lock it. The glass shade must be
inserted correctly before you can lock it in, so check the locking mechanism when performing this task. Fig.7.
NOTE: FOR FAN MODELS WITHOUT LIGHT, IGNORE THIS INSTALLATION PROCESS.
8. Refer to the wiring diagram provided for Electrical Connection/installation. Fig. 8 & 9
WARNING: To prevent electrical shock or risk of fire, do not attempt to perform the electrical connection
wiring yourself. All electrical connections must be carried out by a qualified licensed electrician.
NOTE: An additional all pole disconnection switch must be included in the fixed wiring.
9. After completing the electrical wiring at the mounting bracket terminal and connecting the fan motor and fixed
wiring via the quick connector, cover the mounting bracket with the canopy cover. Ensure all electrical wirings are
tucked inside the canopy cover and that they are not damaged during this step, and secure with screws. Fig.10

7
Fig.6 Fig.7
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENCED ELECTRICIAN
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED
WIRING.
Fig.8 Wiring diagram
NOTE: The light switch wiring diagram is omitted for models that do not have the light feature.
ELECTRICAL WIRING DIAGRAM
INSTALLING THE FAN

8
Fig. 9 Rotary switch and controller capacitor wiring diagram.
Fig. 10 Secure the canopy with screws

9
FAN WALL CONTROL
Your ceiling fan is controlled via the rotary switch (fan) and rocker switch (light) via the wall controller. Refer to Fig.11
SWITCH POSITION
DESCRIPTION
OFF –FAN IS OFF
1 –FAN IS “ON”, SPEED = HIGH
2 –FAN IS “ON”, SPEED = MEDIUM
3 –FAN IS “ON”, SPEED = LOW
LIGHT SWITCH –Toggle to switch ON/OFF the light
WALL CONTROLLER
FIG. 11 Fan Wall Controller
USING YOUR CEILING FAN
INSTALLING THE FAN

10
REVERSING SWITCH
Your ceiling can operate either in fan mode or reverse fan mode.
SUMMER Mode: The reverse switch shall be in “down” (SUMMER) position to make the fan rotate in
the anticlockwise direction. The airflow will be directed downwards, for cooling in summer.
WINTER Mode: The reverse switch shall be “up” (WINTER) position to make the fan rotate in
clockwise direction. The airflow will be directed upwards, for energy conservation in winter.
FIG. 12 Reverse Switch
LIGHT FUNCTION
NOTE: FOR FAN MODELS WITHOUT LIGHT, IGNORE THIS PROCESS.
The fan light can be switched ON/OFF via the light switch on the Wall Controller. Fig.11
Changing lamp or Re-lamping:
When changing or re-lamping, for your safety, the following should be considered:
1) Switch OFF the light and FAN from the mains supply and allow the lamp to cool;
2) Remove the glass cover / diffuser by twisting anti-clockwise.
3) Remove the bulbs from E27 sockets. Replace with new bulbs.
Note: Refer to the specification information for replacement lamp type.
4) Replace the glass cover / diffuser by twisting clockwise.
CAUTION: Be careful when using a ladder for changing lamp or re-lamping.
NOTE: MECHANICAL NOISE MAY BE NOTICED ON INSTALLATION-ALLOW AT LEAST 8 HOURS SETTLING-IN
PERIOD. SOME FAN WOBBLES MORE THAN OTHER—EVEN IN THE SAME MODEL.

11
Please note that all ceiling fans are not the same, even in the same model—some may move more or less than
others. Movement of a couple of centimetres is quite acceptable and does not suggest the fan will fall down.
Even when all blades are weighted and grouped by weight, it is impossible to eliminate wobble altogether and
should not be considered a problem. Ceiling fan tend to move during operation due to the fact that they are not
generally rigidly mounted
You may do the following actions to reduce the wobbling
1) Check all the blade mounting screws are tightened and securely.
2) Wobbling problems may result from inconsistent blade level. To check blade level, measure the distance
from each blade tip to the ceiling.
Note: If measurements are inconsistent:
- check blade mount screws are not too tight or loose as this can cause the blade tip to be unlevelled;
- An out of shape blade can cause wobbling. Check by removing the blade and lay it on a flat surface. A good
flat blade will lay flat on the surface.
3) Blade tracking may be checked simply by use of a household ruler as shown in below Figure. Place the
ruler vertically against the ceiling and even with the outside leading edge of a blade. Note the distance of the
edge of a blade is the same as the others. Turn the blade slowly by hand to check the remaining blades. If a
blade is not in alignment, the blade is either out of shape / warp or the blade screws are not evenly tighten
or either loose.
FIG 13.
BALANCING KIT
Balancing kit is provided to balance the ceiling fan on initial installation. Please refer to the instruction on how to
use the balancing kit.
The balancing kit can be used to assist re-balancing should the ceiling fan becomes un-balanced again, so store
your balancing kit away after first use.
BALANCING / WOBBLYING TROUBLE SHOOTING
INSTALLING THE FAN

12
CARE & CLEANING
Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth
to avoid scratching the paint finish. Please turn off electricity power when you do so.
Do not use water when cleaning your ceiling fan. It could damage the motor or the wooden blades and
create the possibility of an electrical shock.
Motor has permanently lubricated ball bearing. No need to oil
The manufacturer warranty covers actual faults that may develop, but NOT minor complaints, e.g. noise from
motor run—ALL ELECTRIC MOTORS ARE AUDIBLE TO SOME EXTENT.
Ceiling fan tend to move during operation due to the fact that they are not generally rigidly mounted—if they
were, they could generate excessive ceiling vibration and stress on their mountings.
Movement of a couple of centimetres is quite acceptable and does not suggest the fan will fall down.
Ceiling fans are mounted very securely on steel brackets with rubber cushioning or with ball-joints to allow
free movement.
Please note that all ceiling fans are not the same, even in the same model—some may move more or less
than others.
Threaded components working slighting loose or blade carriers even slightly bent due to vigorous cleaning or
bumping can cause extra wobble and noise. THIS IS NOT COVERED UNDER WARRANTY- but a little care and
maintenance can reduce or prevent this problem.
This is the biggest cause for service calls, which are outside the manufacturer’s warranty. If a fan has a fault, it will
be noticeable at all times. Naturally, when everything is quiet at night, you will be more inclined to hear small
noises, which may not be noticeable at other times. Even slightly power fluctuations, and mains frequency signals
superimposed in your electricity supply for off-peak hot water control may cause a change in fan motor noise.
This is normal.
Except for a manufacturing fault, which is extremely rare, FAN LIGHTS AND GLOBES ARE NOT COVERED UNDER
YOUR FAN WARRANTY. Noises and vibration etc. are often more accentuated when a fan light is fitted.
For instance a fan light glass that has not been tightened or worked loose can cause a rattle. Again, care and
maintenance will reduce this
Glass of all kinds is warranty to the retailers’ door and subject to the retailer checking it on delivery.
WOBBLE
NORMAL WEAR AND TEAR
BUMP-IN-THE NIGHT
FAN LIGHT
WARRANTY SERVICE
FAN CARE AND WARRANTY INFORMATION

13
Throughout Australia, but in particular Sydney and other parts of NSW and Queensland, electricity distributors use a
remote control and switching system that is commonly called ripple control. Ripple control has existed for many years
and is used for controlling demand and implementing different customer tariffs.
Our electricity supply is 240 Volts AC 50 Hertz. AC means alternating current, a type of electrical energy that flows in
one direction for half a cycle, and then the opposite direction for the other half cycle. 50 Hertz means there are fifty cycles
per second. For electrical and electronic products a cycle rate of 50 Hertz is very slow and therefore the wires carrying the
power can also carry other signals. Ripple control systems superimpose signals on the 50 Hertz mains supply so they can
be distributed throughout a local power grid. Ripple control signals are used to switch on and off high power consumption
equipment such as water heaters and water supply pumps.
Electrical equipment such as televisions, toasters, fans, fluorescent and halogen lighting and some appliances may be
sensitive to ripple control signals. This results in an audible buzz being generated whenever the signals are present. As
different frequencies for these signals are used in different areas, products may respond is some areas and not others.
Some areas have more than one ripple control system in operation and different signals may be present at different times
and affect different products.
WILL I BE AFFECTED?
In areas that have ripple control installed for off-peak tariff switching (such as off-peak hot water systems) there is
usually a dual tariff meter installed, or dual meters. A smaller control box marked “Zellweger” may also be present. The
meter or Zellweger box will usually have the ripple control signal frequency marked on it (for example 1050 Hz). Even if
you do not have off-peak equipment installed your power supply may still be affected by ripple control signals. Apart
from looking for the control signal marking in your meter box there is no way of knowing in advance if you will be
affected by ripple control signal noise.
WHAT CAN I DO IF I AM AFFECTED?
There are ripple control signal filters available for sale from experienced lighting and fan dealers. These filters have to be
installed by a licensed electrician and each filter has to be matched to the particular signals in your area. Your dealer
usually knows the signals used in their local area and can recommend the correct filter.
It is not possible to build an electric motor based product that rejects all the ripple control signals and the signals differ
from location to location. If you are affected by ripple control noise in your fan or lighting product please contact your
local dealer to purchase the appropriate filter. The cost of the filter and the cost of installation are not covered by the
purchase price of the fan or light. Occasionally the ripple control signals are so strong they cannot be sufficiently filtered.
WARRANTY CLAIMS:
Ripple control signal noise is not covered by warranty. If you make a warranty based service call for ripple control noise,
you will be charged for the call-out by the electrician if he/she does not find a genuine fault with the product.
Note: Ripple control are commonly used in NSW (New South Wales), and Queensland for
off-peak tariff switching.
RIPPLE CONTROL
(Abstract from Hunter Pacific International)

14
The fan must be installed so that the blades are more than 2.1 meters above the floor.
According to law in Australia, all electrical connections & disconnection must be installed by licensed
electrician. This ceiling fan is within this requirement.
According to our warranty terms, only the fans installed by licensed electrician are covered by warranty
service.
WARNING: THE CEILING FAN MUST BE SWITCHED OFF, BEFORE TROUBLE
SHOOTING IS PERFORMED.
TROUBLE
PROBABLE CAUSES
SUGGESTED REMEDY
1. Fan will not start
(Warning: THE ceiling must
be switched OFF, and the
assistance of a licensed
electrician maybe required.)
A. Fuse or circuit breaker blown.
Check main and branch circuit fuses or
circuit breakers.
B. Loose power line connections to
the fan.
Check line wire connections to fan
C. Speed controller not in correct
position.
Check speed controller’s position.
2. Fan Wobbles
(Refer to Wobble section of
the manual for further
information.)
A. Fan blades are not horizontal to
ceiling.
Refer to “wobbling fixing” section of
manual.
- The blade may require adjustment
at the blade mounting screws;
- The blade is out of shape, thus
causing wobbling. New blades set
will require to be replaced. Contact
your local Beacon Lighting store.
B. Blade screws are loose.
Make sure all screws are securely
fastened.
C. Blade/s are out of shape
Remove blade and lay on a flat surface to
check if blades are out-of-shape. Contact
agent or manufacturer for replacement
blades.
3. Fan sound noisy
A. Top canopy touching ceiling.
Lower canopy from ceiling to ensure
minimum 3 mm clearance.
B. Loose fan blade screws.
Re-tighten all screws on fan blades but
never over-tighten.
C. Ceiling fan not secured against
ceiling.
Re-tighten all screws in the hanging
bracket or plate.
D. Incorrect speed controller.
Change the controller to the one supplied.
E. Audible buzzing noise. Cause by
Ripple Control signals. Please refer
to the Ripple Control section of this
manual.
Install a Ripple Control filter. (Refer to the
Ripple control information in this manual.)
4. Mechanical Noise
A. Allow at least 8 hours settling-in
period.
5. Light will not turn ON
(Optional light kit ONLY)
The globe/lamp has failed.
Replace globe/lamp
TROUBLE-SHOOTING CHECKLIST
WARNING

15
All electric motors, including fans make some noise and may feel hot if touched—this is not a fault.
Some fan wobble more than other—even in the same model.
Fan lights can rattle, but are not covered under warranty
Fan wall controller make slight buzz and get warm especially on lower setting
These occurrences are not covered by the manufacturer’s warranty.
AIRLIE ECO
SERIES models
Rated Voltage
Rated power
(motor)
Rated power lamp (for
models with light only)
Lamp type
48”fan with light
230-240 VAC
65W
MAX. 2 x 15W CFL Spiral
Only
E27
48”fan without
light
230-240 VAC
65W
N/A
N/A
52”fan with light
230-240 VAC
65W
MAX. 2 x 15W CFL Spiral
Only
E27
52”fan without
light
230-240 VAC
65W
N/A
N/A
NOTES TO INSTALLERS
TECHINCAL INFORMATION

16
This product is guaranteed against electrical defects in material or manufacturing workmanship for
faults when under normal domestic/residential conditions for a certain period of time from the date of
purchase. This warranty covers parts and labour costs for the motor subject to the following conditions:
1. Installation being performed by a qualified licensed Electrician.
This warranty will not apply if the ceiling fan is installed by anyone other than a licensed electrician.
Problems arising from incorrect installation are not covered by warranty. The cost of repairs and/or
service call where the defect is due to the installation and not due to faulty material or workmanship,
in accordance with wholesaler and their authorized agent, will be payable at time of repair.
2. The correct controller being fitted to the fan.
Only use the controller supplied with the fan or a genuine replacement. Using solid-state dimmer
type or non-genuine controllers will void the warranty. Use of non-genuine controllers may cause the
fan to operate with a loud hum and at altered speeds. Where controllers are supplied complete with
light switch –do not use this switch to operate the fan. Fans connected using this switch to turn the
fan on/off, will not be covered by warranty.
3. Repair work being carried out by licensed electrician only after authorisation by the wholesaler or
their authorised agent to complete the repair and is subject to the supply of dated proof of purchase
and installing electricians details.
4. The exclusion from warranty of any changes to ceiling fan blade or motor, plated and/or painted
finishes due to climatic conditions (moisture, salt air etc) or after 6 months from the date of purchase
or other circumstances deemed to be beyond the control of wholesaler or their authorized agents.
5. The warranty service does not cover:
a. Transportation and in-transit insurance costs, if the product or parts thereof have to be
returned for repair or replacement to the retailer or their authorised agent.
b. Repair of defects caused by accident, fire, misuse, alterations modification, negligence,
incorrect or incomplete installation/operation, any unauthorised person attempting to repair
the ceiling fan, or acts of God.
c. Claims or damage to furniture, carpet, wall, ceilings or any other consequential loss either
direct or indirectly resulting from a faulty ceiling fan.
6. Except in the case of pre-packed integrated light models, light fittings attached to the fan are not
covered by this warranty. Where the fan is pre-packed complete with a light, the light fitting will be
covered by warranty to electrical defect. Tarnishing caused by climatic conditions and breakage of
glass is not covered by warranty. Globes/lamps are also not covered by warranty. All light fittings
attached to the fan must be installed by a qualified licensed Electrician ensuring such attachments
are complete and do not affect the fan’s performance. Light fittings will often accentuate noises and
vibrations, which can be traced to loose glass or fittings and are not covered by warranty. Broken
glass as supplied in the pre-packed light complete models is not considered an item requiring a
warranty service call. Notification within 48 hours of installation is required where glasses have
WARRANTY CONDITIONS

17
found to be broken on unpacking.
7. The warranty applies to actual faults which may develop. Minor running noises are not covered. All
electrical motors have some audible noise. Allow at least eight hours of operation to allow the
bearings to properly seat. The fan, especially when set on low, may feel warm to touch –this is not a
fault. If excessive heat is generated a service call may be required. Fan noises can vary due to slight
power fluctuations and mains frequency signals for off –peak-controlled appliances. These changes
are most noticeable in the quiet of night, mains frequency signals which come across as an
intermittent hum (mostly at night) are out of control of the manufacturer in these cases your
electricity provider should be contacted, or an electrician to fit a suitable noise filter.
8. Threaded components such as blade nuts can work slightly loose during normal operation. These
should be tightened regularly to ensure the fan doesn’t develop operation noises. If noises do
develop, check this aspect before requesting service. This is not covered by warranty.
9. Minor variation of speed may be evident between different fans, even in the same model and is not a
product fault and not covered by warranty.
10. Blades are not covered by warranty against defect in material. The replacement of the blades is not
covered by the in home warranty service call. Notification within 48 hours of installation is required
where blades have found to be broken on unpacking. Contact the retailer or their authorised agent
who will send you a new set of blades. Each blade set is balanced so it is important to replace all
blades. Blades affected by climatic conditions and by maintenance are not covered by this warranty.
This warranty applies only to Australian states and its mainland territories and New Zealand. The
benefits of this warranty are in addition to any rights offered under state or territory law.
For a warranty service, contact the warranty hotline number in this booklet and advise: the model
number and style, the nature of the fault, date and place of purchase. Service cannot be arranged
without this information.
Please also not the following, prior to requesting service, please consult the Trouble-shooting checklist
that is printed in the manual
All electric motors, including fans, make some noise and may feel hot to touch –this is not a
fault.
Some fans wobble more than others –even the same model.
Blades are weighed to be within tolerance to minimize wobbling. In multiple installations do not
mix blades from fans.
Fanlights can rattle and are not covered by warranty.
Finish to the fan, including blades and light complete models, are covered by 2 Years warranty.
Blade and glass replacements are not covered by in home servicing.

18
LUCCI CEILING FAN WARRANTY DETAIL
LUCCI WARRANTY HOTLINE- 1800 602 243
In the event of service being required, please call the Lucci Fan Warranty Hotline on 1800 602 243 between
9am & 5pm (EST) Monday to Friday. Please make sure you have all the ceiling fan details filled out at the end of
the manual before making the call.
Every Lucci ceiling fan is thoroughly inspected and tested before being released for sale. In addition to any
warranty rights or conditions under statutory regulations, Lucci warrants all of its ceiling fans against defective
workmanship and faulty materials for twenty four (24) months from the date of purchase. Lucci undertakes, at its
option, to repair or replace, free of charge, each product or part thereof on condition that;
1. The fan or relevant part has not been subjected to misuse, neglect, or been involved in an accident.
2. The repairs are not required as a result of normal wear and tear.
3. The product was installed by a licensed electrical contractor.
4. A copy of the original receipt of purchase is presented.
5. 12 month warranty applies when used in any non-domestic applications.
6. This warranty does not cover stains, scratch and scuff marks, or dents if the product is purchased
through a factory outlet or to refurbished items.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Lucci Design cannot be held responsible for any repair other than those carried out by it or one of its
Authorised Service Agents. Please keep this warranty information in a safe place. This information must
be produced in the event of service being required.
Distributed by:
Beacon Lighting
140 Fulton Drive
Derrimut, Victoria, 3030
Australia
Ph [phone]
Fax [phone]
Email: [e-mail]

19
CEILING FAN WARRANTY INFORMATION
LUCCI WARRANTY HOTLINE- 1800 602 243
Complete and retain this form for your personal records and warranty purposes.
NAME…………………………………………………………………………………
ADDRESS……………………………………………………………………………
……………………………………………………POSTCODE……………………
MODEL NUMBER……………………………………………………………………
(PO# + DATECODE Sticker here)
PO NUMBER or DATECODE ………………………………………………………
DATE OF PURCHASE………………………………………………………………
INSTALLING LICENSED ELECTRICAN……………………………………………
…………………………………………………………………………………………
LICENCE No…………………………………………………………………………
ATTACH PROOF OF PURCHASE HERE
THIS COMPLETED DETAIL PAGE SHOULD BE PRODUCED AND FAXED TO
THE WHOLESALER OR THEIR AUTHORISED AGENTS BEFORE OBTAINING
WARRANTY SERVICE