LUCCI FUTURA ECO SERIES User manual

FUTURA ECO SERIES
E27 LAMP HOLDER
CEILING FANS
Version 1.0 – Last updated on NOV. 17, 2011 – © Copyright 2011 – LUCCI

2
IMPORTANT SAFETY INSTRUCTIONS
1) This appliance is NOT intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
2) The all-poles disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
3) Meaning of crossed-out wheeled dustbin: Do not dispose of electrical appliances as unsorted municipal
waste, use separate collection facilities. Contact your local government for information regarding the
collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into the food chain, damaging your health and
well-being.
4) The structure to which the fan is to be mounted must be capable of supporting a weight of 45kg.
5) The fan should be mounted so that the blades are at least 2.3 meters above the floor.
6) The fan is designed for indoor use only. Mounting the fan in a situation where it is subject to water or
moisture is dangerous.
7) Only an authorized electrician should execute the installation.
INTRODUCTION
CONGRATULATIONS, as you have just chosen a quality ceiling fan.
BEFORE INSTALLATION
Unpack the fan and carefully identify the parts. Please refer to FIGURE 1.
1. Hanger Bracket x 1
2. Pre-assembled Fan motor, down
rod, and canopy cover x 1
3. Glass shade x 1
4. Blades x 4
5. Screw for Hanger bracket x 2
6. Extra Motor screws for blade x 1
7. Wall plugs for Screw x 2
8. Balancing kits x 1 set
9. Receiver x 1
10. Transmitter x 1
Figure 1.

2
Specifications:
Model Rated Voltage Remote Fan
(watt) Lamp
xxxxxx 220-240V, 50HZ 1.5V, AAA X 4
60W MAX. 2 X 42W Halogen or
MAX. 2 x 15W CFL Spiral
xxxxxx 220-240V, 50HZ 1.5V, AAA X 4
60W MAX. 2 X 42W Halogen or
MAX. 2 x 15W CFL Spiral
xxxxxx 220-240V, 50HZ 1.5V, AAA X 4
60W MAX. 2 X 42W Halogen or
MAX. 2 x 15W CFL Spiral
INSTALLATION
NOTE: Ensure that the power to the supply wires has been turned off before attempting installation.
INSTALL THE MOUNTING BRACKET
Drill two mounting holes in the ceiling joist and securely screw
the mounting bracket to the ceiling using the washers and
mounting screws provided. The mounting plate should be able
to hold a weight of at least 45kg.
NOTE: Proper care must be taken when mounting to concrete
ceilings. For safe mounting, these ceilings may require
stronger screws and plastic plug or anchors than supplied with
the product.
Install mounting bracket (Fig. 2) to ceiling joist via using long
screws provided. Ensure that at least 40mm of the screw is
threaded into the support.
INSTALL THE FAN TO MOUNTING BRACKET ON CEILING
1. Carefully lift the fan and seat the down rod ball assembly into the spacing allocated in the mounting
bracket and lock the ball into place. Fig. 3
Fig.3

3
2. Remove the screws from the light plate and remove the light plate. Fig.4
Fig.4
3. Before installing the blades, remove the blades screws that was locked to motor in advance. Fig.5
Fig.5
4. Insert the blades through the side slot of motor and align with the 3 holes. If the holes do not align, the
blade is upside down. The blade should fit snugly and the screws should slot in vertical/perpendicularwith
the blade screw holes.
5. Secure the blades with 3 blade screws, and ensure that the 3 blade screws are tightened at the same time.
Do not tighten on screws first, and do not over tighten the screws as this can damage the blades. Repeat
this process for all blades. Fig.6

4
Fig.6
6. Replace the light plate as describe in step 4 and secure with screws as shown in Fig.7.
Fig.7
7. Insert and secure the light bulbs into the ES sockets as shown in Fig.8.
8. Carefully place the glass shade cover over the lamp and twist clockwise to lock it. The glass shade must
be inserted correctly before you can lock it in, so check the locking mechanism when performing this task.
Fig.9
Figure 8 Figure 9

5
WIRING
The wiring can now be installed ready for connection to the terminal block in the ceiling canopy of the fan.
Wiring requirement at the terminal block:
- Connect main supply Live wire to “L”
- Connect main supply Neutral wire to “N”
- Connect Earth wire to “E”.
NOTE: AN ISOLATION SWITCH SHOULD BE INSTALLED SOMEWHERE IN THE FIXED WIRING OF A
REMOTE FAN IN CASE REMOTE IS LOST, OR FOR SERVICING OF THE FAN.
FINISH THE INSTALLATION
1) Insert the remote receiver in mounting bracket
2) Connect remote to motor wire via plugging the plug and socket together and connect remote to mounting
bracket via plugging the plug and socket together
3) Cover the mounting bracket with the canopy, and secure the canopy via screws.
Fig.10
REVERSE FUNCTION
Your ceiling can operate either in fan mode or reverse fan mode.
SUMMER Mode: The reverse switch shall be in “down” (SUMMER) position to make the fan rotate in the
anticlockwise direction. The airflow will be directed downwards, for cooling in summer.
WINTER Mode: The reverse switch shall be “up” (WINTER) position to make the fan rotate in clockwise
direction. The airflow will be directed upwards, for energy conservation in winter.

6
HOW TO USE THE FAN/LIGHT WITH REMOTE CONTROL
SETTING DIP SWITCHES
When two or more fans are located near each other, you may desire to have the receiver/transmitter for each
fan set to a different code, so that the operation of one fan does not affect the operation of the other fans.
The DIP switches for the receiver are located on the flat surface of the receiver. The DIP switches for the
transmitter are in the battery compartment. Fig. 11.
NOTE: Ensure that the power to the supply wires has been turned off before setting the code.
NOTE: Before you change the DIP switch settings, make sure the battery is not connected to the transmitter.
Figure 11 Figure 12
Change the position of the DIP switches in the remote transmitter and the receiver. Make sure that the DIP
switches match in theremote receiver and transmitter. If they don’t match, the transmitter will not function. Fig.
12

7
ICONS ON THE REMOTE LCD PANEL
Figure 13
Auto mode temperature setting icon
1) Indicate the temperature at which the fan turns on, when the fan is set to FAN AUTO function.
2) Indicate the time at which the fan turns off, when the fan is set to FAN TIMER function.
3) The icon will switch from temperature setting and timer setting every two seconds automatically.
Room temperature setting icon
1) Indicate the room temperature.
2) Indicate the time at which the light turns off, when the light is set to LIGHT TIMER function.
3) The icon will switch from temperature setting and timer setting every two seconds automatically.
Low battery icon
When the battery low icon is flashing, that means battery power level is low, please replace the batteries
immediately.
Fan speed icon
Display the fan setting is at which speed level (high, medium, low, off )
Fan running mode icon
Indicate the fan is set to MANUAL mode or FAN AUTO mode
Lighting status icon
Display the light setting is ON or OFF

8
BUTTONS ON THE REMOTE
FAN AUTO: Press the button to switch from FAN AUTO mode to MANAUL mode.
FAN: Press the button to set fan running at HIGH – MEDIUM – LOW – OFF speed.
FAN TIMER: Press the button to turn off the fan at setting time automatically.
LIGHT TIMER: Press the button to turn off the light at setting time automatically.
Press and hold the button for 10 seconds to switch from degree Celsius to degree Fahrenheit.
LIGHT DELAY: Press the button to active the light delay function, which will turn off the light 3 minutes later.
Up: Set the temperature and time up
Down: Set the temperature and time down
LIGHT switch: Press the button to turn ON/ OFF the light.
Use the FAN AUTO Function
Press the FAN AUTO button to active FAN AUTO function, and then press the UP/ DOWN buttons to set the
temperature at what you preferred. The fan will run at the HIGH, MEDIUM, LOW or OFF speed automatically
via comparing to room temperature as following:
Room temperature is lower than setting temperature: ------------------> OFF
Room temperature is higher than setting temperature by 0˚ C -------> LOW
Room temperature is higher than setting temperature by 2˚ C -------> MED
Room temperature is higher than setting temperature by 4˚ C -------> HI
Press the FAN AUTO button again to turn off the FAN AUTO function.
Use FAN/ LIGHT TIMER Function
Press the FAN TIMER / LIGHT TIMER buttons to active the timer function, and then press the UP / DOWN
buttons to set the time at what you preferred. The fan and light will turn OFF at setting time.

9
AFTER INSTALLATION
WOBBLE:
NOTE: CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE
MOUNTED ON A RUBBER GROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE CEILING IT
WOULD CAUSE EXCESSIVE VIBRATION. MOVEMENT OF A FEW CENTIMETRES IS QUITE
ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM.
TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE
MOUNTING BRACKET AND DOWN ROD ARE SECURE.
BALANCING KIT: Balancing Kit is provided to balance the ceiling fan on initial installation. Please refer to the
instruction on how to use the Balancing Kit. The balancing kit can be used to assist re-balancing should the
ceiling fan becomes un-balanced again, so store your balancing kit away after first use.
NOISE:
When it is quiet (especially at night) you may hear occasional small noises. Slight power fluctuations and
frequency signals superimposed in the electricity for off-peak hot water control, may cause a change in fan
motor noise. This is normal. Please allow a 24-hour “breaking -in” period, most noises associated with a new
fan disappear during the time. The manufacturer’s warranty covers actual faults that may develop and NOT
minor complaints such as hearing the motor run – All electric motors are audible to some extent.
CARE AND CLEANING
1) Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to
avoid scratching the paint finish. Please turn off electricity power when you do so.
2) Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the
possibility of an electrical shock.
3) Motor has permanently lubricated ball bearing. No need to oil
NOTE: Always turn off the power and disconnect thefemale plug 1 and male plug 1 before attempting toclean
your fan.