LUCCI Airfusion Radar User manual

LUCCI
AIRFUSION RADAR
DC CEILING FAN
INSTALLATION
OPERATION
MAINTENANCE
WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

Airfusion Radar Installation Instructions
1 | Page
CONTENTS
Page 2
Important information
Safety precautions
Page 3
Parts list
Page 4-7
Installing the fan
Page 7-10
Using your ceiling fan
Page 11
Care & cleaning
Warranty service
Wobble
Normal wear and tear
Bump in the night
Fan light
Page 12
Trouble shooting checklist
Page 13
Notes to installer
Technical information
Page 13-15
Warranty conditions
STALLAT

Airfusion Radar Installation Instructions
2 | Page
IMPORTANT INFORMATION – PLEASE READ PRIOR TO INSTALLATION
Congratulations on purchasing the latest in energy saving ceiling fans. This Airfusion Radar fan runs on DC (direct
current) power which gives it the benefit of being super energy efficient whilst still maintaining high volume air-movement
and silent operation.
Energy saving - The DC motor is the latest technology in fan design. Its highly efficient motor saves up to 65% more
energy than ceiling fans with traditional AC motors.
Silent operation – This DC fan motor is programmed with a stabilized current which efficiently reduces motor noise.
Low operating temperature – The DC power is managed effectively which brings down the motor operating
temperature to less than 50degs. This results in a much cooler motor than a standard AC fan and increases the longevity
of the motor.
Regular AC ceiling fans usually come with only 3 speeds, this Airfusion Radar DC fan comes complete with a 6 speed
remote, which gives a greater choice of comfort levels.
SAFETY PRECAUTIONS
1) This ceiling fan is NOT intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
2) Children should be supervised to ensure that they do not play with the appliance.
3) An all-pole disconnection switch must be incorporated in the fixed wiring in accordance with the wiring rules.
4) Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems
available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can
leak into the groundwater and get into the food chain, damaging your health and well-being.
5) The structure to which the fan is to be mounted must be capable of supporting a weight of 30kg.
6) The fan should be mounted so that the blades are at least 2.3 metres above the floor for Europe.
7) The fan should be mounted so that the blades are at least 2.1 metres above the floor for Australia.
8) This fan is suitable for indoor use only. Mounting the fan in a situation where it is subject to water or moisture is
dangerous.
9) Only an authorized electrician should execute the installation.

Airfusion Radar Installation Instructions
3 | Page
PARTS LIST
Unpack your ceiling fan carefully. Remove all parts and hardware. Place the fan motor on a cloth or soft surface to avoid
damaging the finish.
•Do not lay the motor housing on its side – the decorative housing may become bent or damaged.
•Verify that all parts are present before starting assembly.
•Check the packaging carefully for missing parts.
Examine all parts. You should have the following:
1 Mounting bracket x 1
7 Remote transmitter with holder x 1 set
2 Fan assembly with hanging plate, receiver, and
motor x 1
8 Extra Motor screws x 1 (not shown)
3 Motor housing x 1
9 Wooden screw x 4 (not shown)
4 Blade x 3
10 Screw for remote holder x 2 (not shown)
5 Blade bracket kit x 3
11 12V Battery for remote x 1 (not shown)
6 Bottom cover x 1
Fig. 1

Airfusion Radar Installation Instructions
4 | Page
INSTALLING THE FAN
TOOLS REQUIRED:
- Phillips / Flat head screwdriver
- Pair of pliers
- Adjustable spanner
- Step ladder
- Wire cutter
- Wiring, supply cable as required by local provincial and national wiring codes and regulations.
INSTALLING THE MOUNTING BRACKET
The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the blade to the
nearest objects or walls.
Secure the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 30kg, with two
long screws provided. Ensure at least 30mm of the screw is threaded into the support.
NOTE: The bracket screws provided are for use with wooden structures only. For structures other than wood,
the appropriate screw type MUST be used.
ANGLED CEILING INSTALLATION
This fan hanging system DOES NOT support a degree angled ceiling installation.
Fig. 2

Airfusion Radar Installation Instructions
5 | Page
HANGING THE FAN MOTOR ASSEMBLY
•Lift the fan assembly to the mounting bracket (1) and let the J-hook of the mounting bracket (4) go through the hole
of the hanging plate and hang up the fan assembly (3). Fig. 3
•Connect the male and female connector together (2). Fig. 3
•Complete the electrical wiring using the diagram below (Figure. 4).
PREPARE AND COMPLETE THE ELECTRICAL WIRING --- WIRING DIAGRAM (Fig. 4)
WARNING:FOR YOUR SAFETY, ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A LICENSED
ELECTRICIAN.
NOTE: AN ADDITIONALALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED WIRING.
NOTE: IF THERE ARE TWO OR MORE DC CEILING FANS INSTALLED IN THE ONE LOCATION, AN ISOLATION
SWITCH IS REQUIRED FOR EACH CEILING FAN. THIS IS REQUIRED WHEN PROGRAMMING THE REMOTE AND
RECEIVER TO PAIR TOGETHER.
Fig. 4
Fig. 3

Airfusion Radar Installation Instructions
6 | Page
INSTALL THE CANOPY COVER
•Loosen 2 screws (2) from the mounting bracket. Fig. 5
•Loosen 2 screws (1) by half thread from the mounting bracket. Fig. 5
•Lift the hanging plate of the fan assembly up to the mounting bracket and let the L-shape slot on the hanging plate
go through the screws (1) on the mounting bracket. Turn the hanging plate until it locks in place at the end section
of the L-shape slot and secure it by tightening the two screws (2). Avoid damaging the electrical wiring prepared
previously.
•Finally attach the motor housing to the hanging plate and secure it by pushing the hooks (3) into the slot holes and
turn it anti clockwise.
BLADE INSTALLATION
•Insert the blade screws through the blade assembly in the following order - bracket kit (2) and blade (1).
Attach the blade assembly to the motor and secure it by tightening the 2 screws (3). Fig. 6
•Repeat to install the other blades.
•Finally install the bottom cover (4) to the shaft of the motor by rotating it clockwise.
Fig. 6
Fig. 5

Airfusion Radar Installation Instructions
7 | Page
LIGHT KIT Installation (Light kit - optional)
NOTE:The light kit must be installed by a licensed
electrician.
NOTE: The light kit is available for selected ceiling fan
models and as an optional light kit.
1. Remove the bottom cover from the shaft.
2. Remove the shinkable tube from the light wires
connector.
3. For light kit installation, please refer to the light kit
installation user guide.
USING YOUR CEILING FAN
Pairing Transmitter and Receiver – when 2 or more DC ceiling fans are installed in one location
When two or more ceiling fans are located near each other, you may desire to have the receiver/transmitter for each fan
set to a different code so that the operation of one fan does not affect the operation of the other fan/s.
The DIP switches for the transmitter (remote hand piece) are located in the battery compartment of the transmitter.
Configuring the DIP switches will allow a unique transmission code assigned to each ceiling fan.
NOTE: Ensure that you have installed an all - pole disconnection switch in the fixed wiring for each fan, when using DIP
code function.
NOTE: Ensure power to the Receiver is ON prior to pairing the transmitter with the receiver.
Transmitter/Receiver pairing for ceiling fan 1:
•Turn off both ceiling fans 1 and 2 via the mains supply to the receiver.
•Slide the cover of the battery compartment of the transmitter to access the DIP switches. This will be transmitter 1.
•Change the position of the DIP switches in the remote transmitter 1, so that it will be different to transmitter 2. Fig. 8
•Install the 12V DC battery in the compartment. Please make sure the polarity of the battery is correct.
•Turn on the power to receiver 1. Keep the power OFF to receiver 2. (Each ceiling fan must have its own isolation
switch, so that only the ceiling fan that needs to be paired with the transmitter will be ON).
•Press and hold the SET button of transmitter 1 for 6 seconds within 60 seconds of switching the power to the
receiver of ceiling fan 1.
•Now the transmitter should be paired with the receiver of ceiling fan 1. Turn ON/OFF or change the speed of ceiling
fan 1 by the transmitter to check the operation.
Fig. 7

Airfusion Radar Installation Instructions
8 | Page
Setting DC Ceiling fan 2:
•Turn off both ceiling fans 1 and 2 via the mains supply to the receiver.
•Slide the cover of the battery compartment of the transmitter to access the DIP switches. This will be transmitter 2.
•Change the position of the DIP switches in the remote transmitter 2, so that it will be different to transmitter 1. Fig. 8
•Install the 12V DC battery in the compartment. Please make sure the polarity of the battery is correct.
•Turn on the power to receiver 2. Keep the power OFF to receiver 1. (Each ceiling fan must have its own isolation
switch, so that only the ceiling fan that needs to be paired with the transmitter will be ON).
•Press and hold the SET button of transmitter 2 for 6 seconds within 60 seconds of switching the power to the
receiver of ceiling fan 2.
•Now the transmitter should be paired with the receiver of ceiling fan 2. Turn ON/OFF or change the speed of the
ceiling fan 2 by the transmitter to check operation.
Note: The pairing of Transmitter and Receiver is not required if only one ceiling fan is installed. When more than
two ceiling fans are installed near each other, please refer to the instruction above.
Remote Control Buttons
○
1 - FAN SPEED CONTROL BUTTON:
There are 6 available speeds. ○
Ibutton is for the lowest
speed, and ○
VI button is for the fastest speed.
NOTE: WHEN YOU TURN ON THE FAN FOR THE FIRST
TIME OR SWITCH THE MAIN POWER TO THE
CONTROLLER, YOU NEED TO START THE FAN ON HIGH
“○
VI ” SPEED FIRST AND THEN CHOOSE A LOWER
SPEED. A 5-10 SECONDS IS REQUIRED TO ALLOW THE
DC FAN TO RESPOND TO THE REMOTE EACH SPEED
OR FAN DIRECTION SELECTIONS, AS DC FANS
INCORPORATE A SENSOR CONTROL WHICH CONTROLS
THE POWER TO THE MOTOR.
Fig. 9
Fig. 8

Airfusion Radar Installation Instructions
9 | Page
○
2 - FAN OFF BUTTON:
Press the button to turn the fan off.
○
3 - REVERSE FUNCTION BUTTON:
Press the button to activate the reverse running function. The fan must be operating to activate the reverse function.
○
4 - LIGHT CONTROL BUTTON:
Press the button to turn on/off the light.
THE RECEIVER PROVIDES THE FOLLOWING LEVEL OF PROTECTION:
•Lock position: the receiver has a built in safety feature to protect against obstruction during operation. The motor
will be locked from operation and will disconnect from power after 30 seconds of interruption. Please remove
obstacles before re-starting. To reset, simply turn off the power supply to the fan motor and re-start.
•Over 80W protection: when the receiver detects power consumption which is greater than 80W, the receiver power
will be stopped and operation will immediately discontinue. Turn the receiver power on after 5 seconds to restart the
fan.
REPAIRING THE FAN RECEIVER & REMOTE PAIRING
Should the remote and receiver lose control after installation or during use, the pairing of the remote and the
receiver must be repaired. Below are the operating symptoms and method to repair the pairing of the DC ceiling
fan remote and receiver.
Issues:
•Loss of control - Fan is only running at high speed after installation
•Loss of control - No reverse function after installation
•Loss of control - Remote cannot communicate with receiver
Solution:
If the fan runs at the highest speed continuously, it means the wiring of the installation is correct. When the fan operates
on high speed only or fails to operate in reverse function or any other command/s, it is recommended to repair the
communication pairing of the remote and receiver. Please follow the steps below:
A. Remove the battery cover of the remote, check the 434 MHz sticker area, make sure the battery is installed
correctly and the red LED light indicator will be flashing, it means the remote function is okay.