LUCHT LHZ Technotherm International CPH 1000 User manual

D
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE
REFERENCE. BE SURE TO OBSERVE ALL LABELS AND WARNINGS ON THE APPLIANCE
Edition: 01/14
Id Nr. 911 360 860
Installation and technical manual
Panel Heater CPH 1000 - 2400
GB
All manuals and user guides at all-guides.com
all-guides.com

2 Edition:01/14
Manual
CPH 1000 - 2400
1. Important Safety instructions
•People (including children) who are limited in their physical, sensory, or mental capacities should
not use this device at any time. Furthermore do not handle this instrument if you do not possess
the necessary experience and knowledge to do so. This device should only be handled under the
supervision of a qualified person and after a thorough introduction.
•Do not leave children alone with the device, and supervise them at all times to keep them from
getting harmed.
•WARNING: Do not cover! Otherwise this instrument will overheat.
•Do not place the heater underneath a socket, drainage or the like.
•To keep from getting burned, do not touch heater´s surface whenever it is turned on.
•Please use the handle whenever you have to move the heater.
•Do not put the cord underneath the carpet or a rug and make sure that it is not a tripping hazard.
•Plug the heater into properly grounded sockets only.
•Do not use the heater in any other way than described in the user manual. Any other way of use
may lead to fire, electrocution, and may cause serious harm to the person.
•Do not use this device near bathtubs, showers or swimming pools.
•In case the connection cable is damaged it has to be replaced by the manufacturer or someone
commissioned by the manufacturer.
WARNING: Do not use a switching-oriented device, like a timekeeper, when operating this heater.
This could cause a change in the thermal adjustment which is potentially hazardous!
•To keep the device from overheating, do not put towels or clothing on top.
•When using the heater, make sure it is in an upright position and positioned on a even and dry
place.
•Do not put any foreign objects into the vent. This may cause electrocution, fire or damage to the
heater.
•Do not use an extension cord unless approved by an electrician.
•This device is for private use only, do not use in any other way than intended by the
manufacturer.
•Do not use the device near curtains, highly combustible, extremely explosive or malleable
materials.
•Keep a distance of a at least 1.0 m between combustible materials- like furniture, cushions,
bedding, paper, clothing, curtains-and the heating device.
•Do not use the device in rooms were petrol, paint or any other flammable liquids are stored.
•Do not use the device outside.
Warning! This device has to be grounded
This device may only be operated using alternating current and the operating voltage indicated
on the power rating plate.
•Nominal Voltage 230V AC, 50 Hz
•Protection Class I
•Degree of Protection IP 24
•Room Thermostat 4°C till 40°C
GB
All manuals and user guides at all-guides.com

3 Edition:01/14
Manual
CPH 1000 - 2400
2.1 Technical data
Model
Power [W]
Dimensions (ill.)
a [mm] b [mm] weight [kg]
CPH 1000
1000
415
215
4,8
CPH 1500
1500
565
365
6,0
CPH 2000
2000
695
495
7,0
CPH 2400
2400
915
715
8,2
2. 2 Operation
Connect the heating convector to the mains supply
to set it into operation.
Switching the appliance on
Switch on the appliance by setting the tumbler switch
to position „1“.
Switching the heating on
Switch on the heating by turning the temperature selector switch and choose the required temperature.
The temperature range extends from 4°C to 40°C graduated into 10 steps. The thermostat switches off
the heating as soon as the preset ambient temperature is reached, which will then be kept constant by
cyclic heating. The high consistency of the thermostat (below 2 K) provides a constantly comfortable
temperature and thus ensures power-saving heating.
Anti-freezing protection
When setting the temperature selector switch to grade „1“ the thermostat automatically cuts in if the
ambient temperature falls below 4°C.
Switching the appliance off
Switch off the appliance by setting the tumbler switch to position „0“.
3. Important notes
During operation the temperature at the front panel and at the hot-air outlet of the convector may rise
above 85 °C. Do not place any objects on or beside the heater, do not put anything between the heater
and the wall. Free air exit must not be hindered by covering the hot-air outlets with any objects such as
curtains, pieces of laundry etc., otherwise risk of overheating. Combustible objects such as wood, paper,
textiles etc. as well as highly flammable substances such as wax, petrol, aerosols must not be placed
near the heater within the hot-air current. Switch the heater off when carrying out work where highly
flammable vapors could emerge, such as laying or sealing parquet or other kinds of floor covering or
when using aerosols, floor wax, petrol etc.
GB
All manuals and user guides at all-guides.com

4 Edition:01/14
Manual
CPH 1000 - 2400
Caution!
The appliance must not be installed in rooms with explosion hazard such as garages etc.
Remove the protection foil from all panels prior to first use. Should the heater give off a bad smell
when it is heated up for the first time this is caused by manufacturing-related residues, which are
harmless to health. This nuisance will disappear within short time. The rising hot air can cause
staining on the wall, a phenomenon seen in all other types of heaters too. The appliance may
only be opened by an authorized professional with the power supply disconnected.
4. Maintenance
To clean the appliance, switch it off and rub it with a moist cloth using a mild detergent if necessary.
Finally polish with a dry cloth. Do not use any abrasive or caustic detergents for cleaning.
This Manual is very important and has to be kept at a safe place at all times. Be sure to hand this manual
to any other succeeding owner of the device.
5. Installation instructions
These installation instructions are an integral part of the appliance and must be kept in a safe place by
the user. Pass it on to any subsequent user if the owner of the appliance changes. Wall convectors are
direct electric heaters that are exclusively intended for being fixed to massive walls. Thanks to graduated
heating capacities they can be adapted to any room size. The convector comes complete with connecting
cable that must be connected to a wall socket. The appliance has been designed to be connected to
230V alternating current (AC).
Fixing
Fix the appliance in such way that any potentially combustible objects cannot catch fire. Therefore, the
minimum safety distances mentioned below must be kept. Fix the heater to an upright wall that is
resistant to a minimum temperature of 90°C.
Keep a distance of 25 cm to the floor. There shall be a minimum space of 10 cm between the heater and
any wooden parts or other objects. Any window sills, roof slopes, brackets etc. must be located at least
50 cm over the hot-air outlets of the heater. If the appliance is used in bathrooms, install it in such way
that the tumbler switch or the temperature selector cannot be touched by a person being in the tub or
under the shower. When fixing the appliance to the wall observe the dimensions given in Fig. 1 and follow
all other instructions for installation. Drill two holes of 7mm and fix the appropriate plugs. Screw in the two
4 x 25 mm screws so that a distance of 1 – 2 mm is kept between screw head and wall. Hang up the
appliance on the suspension brackets which are fixed to the back of the heater and push it to the left until
it stops. Then tighten the left-hand screw through the air exit grille and the provided hole in the back panel
of the heater. Now the appliance is secured against unintended removal.
Caution Do not install the appliance below a wall socket. The appliance is not suitable for
outside use.
GB
All manuals and user guides at all-guides.com

5 Edition:01/14
Manual
CPH 1000 - 2400
Electrical installation
The appliance has been designed to be connected to 230V alternating current (AC). All electrical
installation work, in particular protective measures, must be carried out in compliance with the national
regulations and statutory provisions of the respective utilities provider.
The electrical installation may only be carried out in compliance with the installation instructions
by an authorized professional!
The appliance has been designed for fixed connection. Therefore, it is necessary to install a connector
socket for fixed connection where the connecting cable of the appliance.
H05 VVF 3 x 1.0 mm2
(power class 1000 W)
H05 VVF 3 x 1.5 mm2
(power class 1500 W- 2400 W)
Permanent cables must not be connected directly to the appliance! If the electrical installation is done by
means of an isolating unit, it should be taken care that the isolation is designed with at least 3 mm
separation on all poles.
Type of connection of the appliance:
Type Y acc. to VDE 0700 Part 1.
In case the connecting cable is damaged, it may only be replaced by a repair shop appointed by
the manufacturer!
The minimum distance between appliance and connector socket must be 10 cm. The connecting cable
must not have contact with the appliance.
GB
All manuals and user guides at all-guides.com

6 Edition:01/14
Manual
CPH 1000 - 2400
Diagram of connections
Lucht LHZ Elektroheizung GmbH & Co. KG
Obere Hauptstr. 61
D 09232 Hartmannsdorf
Fon: [phone]
Fax: [phone]
E-mail: [e-mail]
Web: www.technotherm.com
TECHNOTHERM Support:
Fon: [phone]
GB
All manuals and user guides at all-guides.com
all-guides.com