lumishore LUX Livewell Light LW25 User manual

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
1
Without Bezel Fitted With Bezel Fitted
LUX Livewell Light LW25 Installation Guide
Full spectrum color tunable lighting, including cold and warm white light
Please read the following pages before attempting installation
Before you start…
• Always ensure that the vessel’s power source and battery are disconnected or isolated prior
to installation.
• A qualied professional should carry out both the electrical and mechanical installation.
• The LUX Livewell Light is designed to be used in conjunction with the Lumishore LUX Light
Module (see diagram below). Do not connect to any other 3rd party lighting control products
or dimmers.
• The LUX Livewell Light is fully sealed and can be installed inside, outside or underwater in
the livewell tank.
• Choose a location – the light must be mounted on a at – not curved surface.
• Note that tting the Bezel is optional.
45-0161-Rev2

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
2
(0.14in)
3.5mm
(0.972in)
24.7mm
(1.04in)
26.5mm
(1.42in)
Ø 36mm
(1.00in)
ø 25mm
Basic Dimensions - NO BEZEL:
HOLE CUT-OUT
(0.213in)
5.4mm
(0.972in)
Ø 24.7mm
(0.97in)
24.6mm
(1.97in)
Ø 50mm
(1.00in)
ø 25mm
Basic Dimensions - WITH BEZEL:
HOLE CUT-OUT

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
3
Mechanical Installation:
Using a hole saw cut a 1in hole, always cut the hole smaller than needed and le to the correct size to
ensure a snug t.
When tting the lens ensure CLEAR marine sealant is used around the back face of the body as shown
below. Fit lens into the housing. Clean any excess adhesive using a soft cloth and soap and water -
DO NOT USE CHEMICAL CLEANERS.
NOTE: The Lumishore LUX Livewell Light LW25 requires connection to the Lumishore LUX Light
Module. For full electrical installation and wiring diagrams please refer to the LUX Light Module
installation guide.
Power rating = 0.5watts per light
Typical current draw = 0.06A @ 12Volt / 0.03A @24Volt
Installation Diagram
LUX Livewell Lights (Max 16)
Extend using 3-Core Cable
Fitting Bezel is
Optional
CLEAR
MARINE SEALANT
R
O
A
T
E
T
O
S
P
R
E
A
D
A
D
H
E
S
I
V
E
R
O
A
T
E
T
O
S
P
R
E
A
D
A
D
H
E
S
I
V
E
Mounting Panel

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
4
Warranty
LUMISHORE Ltd warrants the LUX Livewell Light LW25 to be free from defects in workmanship and mate-
rials for a period of two years, starting from the date of original purchase. Misuse, abuse, improper installa-
tion, neglect, improper shipping, damage caused by disasters such as re, ood, and lightning, installation
by unqualied personnel, unauthorized repair or modication will void this warranty. For the avoidance
of confusion and doubt, non-compliance with all installation, maintenance and operating instructions in
this document constitute non-conformance with warranty terms.
The LUX Light Control Module is designed to work with Lumishore LUX lighting products ONLY, do not
use with other light brands, this will invalidate the warranty.
CLEAR
MARINE SEALANT
R
O
A
T
E
T
O
S
P
R
E
A
D
A
D
H
E
S
I
V
E
R
O
A
T
E
T
O
S
P
R
E
A
D
A
D
H
E
S
I
V
E
Mounting Panel
If the supplied bezel is to be tted ensure CLEAR marine sealant is used behind the bezel. Clean any
excess adhesive using a soft cloth and soap and water - DO NOT USE CHEMICAL CLEANERS.