lumishore LUX Strip Light SL180 User manual

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
1
LUX Strip Light SL180 (IP68) CRGBW (Cut and Seal) Installation Guide
Full spectrum color tunable lighting, including cold and warm white light
Please read the following pages before attempting installation to ensure
complete understanding of the LUMISHORE Strip Lights
Before you start…
• Always ensure that the vessel’s power source and battery are disconnected or isolated prior
to installation.
• A qualied professional should carry out both the electrical and mechanical installation.
• The Lux Strip Light Is designed to be used in conjunction with the Lumishore Lux Strip Light
Driver modules (see diagram below). Do not connect to any other 3rd party lighting control
products or drivers.
• The lux Strip Light must be cut and sealed prior to installation. Failure to follow the
instructions in this manual will invalidate the warranty. Only sealant supplied is to be used.
• The lux Strip Light is fully sealed and can be installed inside or outside, it can be installed in
wet areas but is not designed to be permanently submerged in water.
• Choose a location – the Strip Light is made from UV resistant material but should not be
installed in areas of strong direct sunlight.
• The Strip Light has a bend radius of 50mm in the vertical axis, do not bend in the horizontal
axis or twist the Strip Light.
45-0181-Rev2
LUX Strip Light SL180 (IP68) CRGBW (Cut and Seal) Installation Guide

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
2
Handling & Manipulating:
DO NOT BEND IN
HORIZONTAL AXIS
DO NOT TWIST
MIN 50mm
VERTICAL BEND ONLY
Installation Diagram:
LUX Strip Lights
Switches
1 2
LUX Strip Light
Driver
NOTE : The Lumishore Lux Strip Lights requires connection to the Lumishore LUX Strip Light Driver
Module. For full electrical installation and wiring diagrams please refer to the LUX Strip Light Driver
Installation Manual (45-0143).
Power Rating = 5 watts Per Meter
Voltage Input Range = 23 - 25V*
*ONLY USE WITH LUMISHORE STRIP LIGHT DRIVER MODULES

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
3
Cutting to length
Unreel the striplight onto a at surface and identify correct end to be cut. Measure and mark out the
required length to cut. If installing around curved areas or corners we recommend that the strip light is
“oered up” before cutting to ensure correct length has been marked out.
1. Locate the closest cut point to the
length required.
2. Only cut on marked
cut points.
1. At the end to be sealed, peel back
20mm of the adhesive backing and
very lightly score the adhesive 10mm
from the end using a sharp blade.
2. Remove the adhesive tape
from the score line to expose
silicone underneath.
5. Half ll the end cap with
silicone adhesive (supplied)
6. Fit end cap, clean up any excess
adhesive. Allow to cure for 24hrs
before handling.
3. Using a pair of scissors cut the strip
light to length. Use a single cutting
motion in the center of the cut pads.
End prep and sealing
It is important that the adhesive backing is properly removed from the end required to be sealed, skipping
this step may compromise the watertightness of the assembly and risk voiding warranty.

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
4
Mechanical Installation - 3M Adhesive Strip
Ensure silicone adhesive (previous page) has fully cured before proceeding. Thoroughly clean the
mounting surface using IPA, ensure it is dust and dirt free.
Peel back the 3M adhesive backing layer and rmly press strip light in place. Allow the adhesive to set for
24 hours before switching the strip light on.
Outdoor Installation - Mounting Fasteners
For outdoor installation, wet areas or tight bend radii: it is recommended that mechanical fasteners
are used in addition to the adhesive layer.
Using suitable screws the fasteners should be placed every 25 - 30cm apart and/or at either side of
the bend
Mounting Clips (Optional)
For narrow mounting channels Lumishore can supply Stainless Steel metal clips. These are attached
using a countersink screw. Gently prize open the metal clip and insert the strip light. Once in place gently
squeeze the clip together over the strip light.
SQUEEZE TOGETHER WITH
STRIP IN PLACE
PRIZE OPEN TO INSERT STRIP
CTSK SCREW
WITH METAL
CLIP
FASTENING CLIP

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
5
Warranty
LUMISHORE Ltd warrants the LUX Strip Light to be free from defects in workmanship and materials for
a period of two years, starting from the date of original purchase. Misuse, abuse, improper installation,
neglect, improper shipping, damage caused by disasters such as re, ood, and lightning, installation by
unqualied personnel, unauthorized repair or modication will void this warranty. For the avoidance of
confusion and doubt, non-compliance with all installation, maintenance and operating instructions in this
document constitute non-conformance with warranty terms.
The LUX Strip Light is designed to work with Lumishore LUX Strip Light Driver Module ONLY, do not
use with other 3rd party drivers, this will invalidate the warranty.