Lutron Electronics GRAFIK Eye QS with EcoSystem Operating instructions

LUTRON
with EcoSystem Control Unit
Installation and Operation Guide
®
Please Read
The GRAFIK Eye QS with EcoSystem
control unit allows for control of both lights
and shades, without interfaces, using
a single control unit. Features include
pushbutton scene recall, info screen
that displays energy savings and status,
IR receiver, astronomic timeclock, contact
closure input, and engravable backlit
buttons that are easy to find and operate.
The built-in EcoSystem bus link can control
up to 64 EcoSystem devices.
Model Numbers: QSGRJ-6E, QSGRJ-8E, QSGRJ-16E
QSGR-6E, QSGR-8E, QSGR-16E
120 V~50/60 Hz 220 - 240 V~50/60 Hz
Unit Capacity (watts) 2000 W 3000 W
MLV 2000 VA / 1600 W 3000 VA / 2400 W
Zone Capacity (watts) 25 – 800 W 40 – 1200 W
MLV 25 – 800 VA / 25 –600 W 40 – 1200 VA / 40 –960 W
See page 7 for EcoSystem bus ratings; see page 8 for IEC PELV/NEC®Class 2 ratings.
For California residents only:
The batteries in these devices contain Perchlorate Material –
special handling may apply.
For more information, visit www.dtsc.ca.gov/hazardouswaste/perchlorate
English Español Français

®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 2
Contents
Features and Functions of the
GRAFIK Eye QS with EcoSystem
Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Wiring the GRAFIK Eye QS with EcoSystem
Control Unit
Overview of Line Voltage/Mains
and EcoSystem Wiring ......................4
Line Voltage Wiring Details...................5
EcoSystem Bus Wiring Details................7
Overview of IEC PELV/NEC®Class 2 Wiring .....8
QS Link Control Wiring Details................9
Powering More Than 3 Wallstations Example ...10
Completing Installation of the
GRAFIK Eye QS with EcoSystem
Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
General Functionality ...................12
Pre-Programmed Button Functionality .....13
Zone Button Operation
Zone LED Displays for % of Lighting Levels....14
Programming Mode
Entering and Exiting Programming Mode ......15
Navigating Menus in Programming Mode ......15
Wireless Mode.........................16
FCC Information ..........................16
Zone Setup
Assigning Load Types ......................17
Assigning Non-Dim Load Types ..............17
Setting Load Types ........................18
Setting High End or Low End Trim ............19
Setting Minimum Level (optional).............19
Labeling a Zone (optional) ..................20
Scene Setup
Setting Zone Levels, Fade Rates,
and Shade Group Actions ..................21
Labeling a Scene (optional) .................22
Enabling/Disabling Daylighting in a Scene .....22
Setting Save Mode
Save Mode Settings .......................23
Quick Scene Programming:
Save by OK Mode .........................23
EcoSystem Setup
Building the System .......................24
Assigning/Unassigning an EcoSystem Device
to a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Addressing EcoSystem Devices..............26
Reset Missing Ballast Addresses.............27
Diagnostics ..............................28
Contact Closure Input (CCI) Setup.........29
Occupancy Sensor Setup................31
Associating Wireless Occupancy Sensors .....32
Selecting the Mode ........................33
Scene Mode .............................34
Zone Mode ..............................35
Labeling an Occupancy Sensor (optional)......36
Configuring Occupancy Sensor Settings
(optional) ................................37
Daylight Sensor Setup ..................38
Associating Wireless Daylight Sensors ........39
Assigning the Mode .......................40
Zone Mode ..............................41
Group Mode..............................42
Labeling a Daylight Sensor (optional) .........44
Pico Wireless Control Setup..............45
Associating with a GRAFIK Eye QS
Wireless Control Unit ......................46
Associating through a QS Sensor Module......47
IR Setup ..............................48
Enabling/Disabling the IR Receiver ...........49
Associating the QS IR Eye with a
GRAFIK Eye QS Control Unit ................50
Associating through a QS Sensor Module......52
Associating Sivoia QS Shades/Drapes
and GRAFIK Eye QS Control Units.........53
Adjusting Shade Settings
Setting Limits.............................54
Preset Adjustment: Simple Method ...........55
Preset Adjustment: Advanced Method ........55
Naming a Group of Shades .................56
Enable/Disable “Stop If Moving”
Functionality .............................57
Associating Sivoia QS Triathlon Shades
with GRAFIK Eye QS Control Unit . . . . . . . 58
Setting Upper and Lower Limits of a Sivoia
QS Triathlon Shade with GRAFIK Eye QS
Control Unit . . . . . . . . . . . . . . . . . . . . 59
Associating Multiple GRAFIK Eye QS
Control Units ..........................60
Timeclock Operation
Setting Time and Date .....................61
Setting Location ..........................62
Setting Daylight Saving Time ................62
Adding an Event ..........................63
Deleting an Event .........................64
Viewing an Event..........................64
Setting a Holiday ..........................65
Viewing a Holiday .........................65
Deleting a Holiday .........................65
Copying a Schedule .......................66
Deleting a Schedule .......................66
Afterhours ............................67
Afterhours Examples.......................68
Setting Up Afterhours ......................69
Ending Afterhours .........................69
Diagnostics and Special Settings
Enabling/Disabling the Timeclock ............70
Enabling/Disabling the Backlighting ..........70
Diagnostics ..............................70
Setting the Security Password ...............71
Language Selection.....................72
Faceplate Removal . . . . . . . . . . . . . . . . . . . . . 72
Troubleshooting........................73
Troubleshooting: Wireless Functions .......74
Troubleshooting: Shade Functions.........75
Troubleshooting: EcoSystem Functions.....76
Warranty..............................77
Contact Information ....................77

OK
12345691011 12 13 14 7815 16
9-16
1-8
®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 3
Optional Shade
button groups
Preset and raise/lower
buttons with integral LEDs
(maximum of 3 button
groups)
Zone numbers
Zone raise/lower buttons
Zone LEDs display current
lighting zone levels
Hinged faceplate
Hinged faceplate
Features and Functions of the GRAFIK Eye QS with EcoSystem Control Unit
Note: Zones 1, 2, and 3 are
integral line voltage dimming
zones that can control line
voltage loads. Remaining zones
are EcoSystem zones only.
Zones 1, 2, and 3 can be either
EcoSystem zones or line voltage
zones (no zone can be both)
Page button
Switches between displaying
zones 1 to 8 and 9 to 16 on
16-zone unit
Note: 6-zone control unit will show only zones 1 through 6.
Info screen
Displays status or
programming functions
Scene buttons
With integral scene
indicator LEDs
Timeclock button
Displays current
timeclock info
“OK” button
Used for programming
Infrared receiver
For handheld remote use
Master buttons
Temporarily raise and lower
lighting levels on unit
USB type mini B
For programming via PC

®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 4
Wiring the GRAFIK Eye QS with EcoSystem Control Unit (continued)
Overview of Line Voltage/Mains and EcoSystem Wiring
12 AWG (4.0 mm2)
each terminal
120 V~
or
220 - 240 V~
Distribution
Panel
Line Voltage/Mains
Cables and Load Wiring
E2
E1
E2
E1
To additional
EcoSystem devices
EcoSystem Bus Wiring
(See the bus wiring details section for
complete specification)
Two 16 AWG (1.5 mm2)
each terminal
EcoSystem devices: LED
drivers, interfaces, or ballasts
Two E1 and two E2 connections are
provided for ease of wiring, and to
provide two connecting points; there is
only one EcoSystem link on the unit.
Note: Ballasts and other EcoSystem
devices must NOT obtain power from a
line voltage output on the GRAFIK Eye
QS with EcoSystem control unit.
Distribution
Panel
L
N
L
N
Dimmable LED bulb*
Load controlled
by power module
or interface
Terminal labels:
L: Hot/Live
N: Neutral
: Ground
1, 2, 3: Dimmed/Switched
line voltage outputs
Power module
or interface
* For a complete list of approved dimmable LEDs please call 1.800.523.9466 or
visit www.lutron.com/dimcflled

®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 5
Wiring the GRAFIK Eye QS with EcoSystem Control Unit (continued)
Line Voltage Wiring Details
• Use properly certified cable for all line
voltage/mains cables.
• Proper short-circuit and overload
protection must be provided at the
distribution panel. You can use up to a
20 A circuit breaker for your installation.
• Install in accordance with all local and
national electrical codes.
• IEC PELV/NEC®Class 2 terminals may
be temporarily unplugged for ease of IR,
occupancy sensor, and control wiring.
• Notice: Risk of damage to unit. Do not
connect line voltage/mains cable to IEC
PELV/NEC®Class 2 terminals.
Step 1: Install wallbox. Mount a 3½in
(89 mm) deep 4-gang U.S. wallbox on a
dry, flat indoor surface that is accessible
and allows for system programming and
operation. Allow at least 4½in (110 mm)
clearance above and below the faceplate
to ensure proper heat dissipation. Allow
1 in (25 mm) for faceplate overhang on
all sides.
Note: 4-gang wallbox available from
Lutron; P/N 241400.
Step 2: Test load wiring.
• Turn power OFF at the circuit breaker or
fuse box.
• Connect a standard light switch between
the live lead and load wire to test the
circuit.
• Turn power ON and check for short or
open circuits. If load does not operate,
the circuit is open. If the circuit breaker
trips (fuse blows or opens), a load short
may exist. Correct short or open circuits
and test again.
Step 3: Check control unit wiring.
•Earth/ground terminal connection must
be made as shown in line voltage wiring
diagrams.
•Do not mix different load types on the
same zone.
• Follow all local and national electrical
codes when installing IEC PELV/
NEC®Class 2 wiring with line voltage/
mains wiring.
WARNING! Shock hazard. May
result in serious injury or death.
Always turn off circuit breaker or
remove main fuse from power line
before doing any work. Before
connecting the loads to the
GRAFIK Eye QS with EcoSystem
control unit, test the loads for
short-circuits.
(continued on next page)
Neutral
Hot/Live Switch
Load
LUTRON
LUTRON
Faceplate overhangs
wallbox on all sides;
allow 1 in (25 mm)
4`in
(110 mm)

®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 6
Wiring the GRAFIK Eye QS with EcoSystem Control Unit (continued)
Line Voltage Wiring Details (continued)
Step 4: Connect line voltage and loads
to control unit.
• Strip 9in (8 mm) of insulation off the line
voltage/mains cables in the wallbox.
• Connect the line voltage/mains, ground,
and load wires to the appropriate
terminals on the back of the control unit.
L: Hot/Live
N: Neutral
: Ground
Terminals 1, 2, 3: Dimmed/Switched
line voltage outputs
9in
(8 mm)
The recommended installation torque is
5.0 in∙lb (0.6 N∙m) for line voltage/mains
connections and 5.0 in∙lb (0.6 N∙m) for
the earth/ground connection.
Note: See the zone setup section for
a list of compatible load types and
instructions for programming the GRAFIK
Eye QS with EcoSystem control unit to
properly recognize them.
Notice: Risk of damage to unit. GRAFIK Eye QS with EcoSystem control units must be
installed by a qualified electrician in accordance with all applicable regulations and
building codes. Improper wiring can result in damage to control units or other equipment.
Note: To avoid overheating and possible damage to equipment, do not install control
units to dim receptacles, motor-operated appliances, or fluorescent lighting not
equipped with Lutron Hi-lume, Eco-10, Tu-Wire, EcoSystem electronic dimming
ballasts, or other EcoSystem devices approved for your location. In dimmed magnetic
low-voltage circuits, you can prevent transformer overheating and failure by avoiding
excessively high current flow. Do not operate control units with any lamps removed
or burned out; replace any burned out lamps immediately; use only transformers that
incorporate thermal protection or fused primary windings. Control units are designed
for residential and commercial use, for indoor use only.

®
EcoSystem bus wiring may be considered
NEC®Class 1 or IEC PELV/NEC®
Class 2.
• NEC®Class 1: EcoSystem bus wiring
may be run in the same conduit as mains
voltage wiring to fixtures.
• IEC PELV/NEC®Class 2: EcoSystem bus
wiring must be separated from all mains
and NEC®Class 1 wiring.
• Consult applicable national and local
codes for compliance.
• Lutron recommends using two different
colors for E1 and E2 (EcoSystem bus)
wires. This will prevent wiring mistakes
in junction boxes where several different
EcoSystem bus wires combine. Use
the following instructions for wiring the
EcoSystem bus.
• Each EcoSystem link can have only 1
GRAFIK Eye QS with EcoSystem control
unit connected to it. No additional
EcoSystem bus supplies can be on the
link.
• Up to 64 EcoSystem devices can be
connected to the EcoSystem link.
• No other devices may be connected to
the EcoSystem link.
WARNING! Shock hazard. May
result in serious injury or death.
Do not wire live. Interrupt power
via circuit breaker before wiring
and servicing the EcoSystem bus
supply.
Step 1: Use the wire size chart at right to
determine which wire size to use based
on the length of the EcoSystem bus.
Step 2: Wire the EcoSystem bus from
terminal E1 and terminal E2 to all
EcoSystem devices.
Step 3: If wiring the EcoSystem bus as
IEC PELV/NEC®Class 2, maintain proper
separation from mains and NEC®Class 1
wiring.
Step 4: Turn on circuit breaker to
energize.
EcoSystem Bus
18 V-250 mA
Wiring the GRAFIK Eye QS with EcoSystem Control Unit (continued)
EcoSystem Bus Wiring Details
Wiring Size and Bus Length
EcoSystem bus wires E1 and E2 are not
polarity sensitive. EcoSystem bus length
is limited by the wire gauge used for E1
and E2 as follows:
Wire Gauge Maximum EcoSystem
Bus Length
12 AWG
(4.0 mm2)
2200 ft (671 m)
14 AWG
(2.5 mm2)
1400 ft (427 m)
16 AWG
(1.5 mm2)
900 ft (275 m)
18 AWG
(1.0 mm2)
570 ft (175 m)
Note: Some EcoSystem devices
(ballasts, drivers, and interfaces)
accept connections to daylight
sensors and occupancy sensors.
For instructions on installing and
operating these devices, refer to
their individual instruction sheets.
EcoSystem bus wiring cables (16 AWG/
1.5 mm2) are available from Lutron, part
numbers C-CBL-216-GR-1 (non-plenum)
and C-PCBL-216-CL-1 (plenum).
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 7

Contact Closure Input Wiring
24 V-50 mA
For settings, see CCI Mode Setup.
®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 8
12 ABC
NH123456
1234
1234
12
ABC
123456LN
1234
12
ABC
123456LN
Note: Use appropriate wire connecting devices
as specified by local codes.
Example:
Occupancy sensor
(maximum 1)
1: COM
2: 24 V-*
3: MUX
4: MUX
Wiring the GRAFIK Eye QS with EcoSystem Control Unit (continued)
Overview of IEC PELV/NEC®Class 2 Wiring
IR Wiring
From external
IR connection
(by others)
18 AWG (1.0 mm2)
each terminal
18 AWG (1.0 mm2)
each terminal
1: IR DATA
2: IR COM
A: CCI SIG
B: 24 V-
C: CCI COM
To control stations,
shades, or other
GRAFIK Eye QS
control units
Data (terminals 3 and 4):
Twisted, shielded pair 22 AWG (0.5 mm2)
each terminal
*Do not connect terminal 2
between any GRAFIK Eye QS
control unit and any other power
supply, including another GRAFIK
Eye QS control unit.
Refer to the QS Link Power Draw
Units specification submittal
(Lutron P/N 369405) for more
information concerning PDUs.
1234
12
ABC
123456LN
Example:
Emergency lighting interface (maximum 1)
Note: The GRAFIK Eye QS control unit must
be powered by a Normal/Emergency
distribution panel for proper ELI
operation. Refer to the LUT-ELI-3PH
Installation Guide for the complete
wiring diagram.
A: CCI SIG
B: 24 V-
C: CCI COM
LUT-ELI-3PH
Signal
+V Input
Circuit Common
QS Link Control Wiring
24 V-100 mA
Common and power (terminals 1 and 2):
Two 18 AWG (1.0 mm2) each terminal (for link <500 ft/153 m)
Two 12 AWG (4.0 mm2) each terminal (for link 500-2000 ft/153-610 m)

• System communication uses IEC PELV/NEC®
Class 2 wiring.
• Follow all local and national electrical codes when
installing IEC PELV/NEC®Class 2 wiring with line
voltage/mains wiring.
• Each terminal accepts up to two 18 AWG (1.0 mm2)
wires.
• Total length of control link must not exceed
2000 ft (610 m).
• Make all connections in the control unit’s wallbox.
• Wiring can be T-tapped or daisy-chained.
• IEC PELV/NEC®Class 2 24 V-150 mA.
System Limits
The QS wired communication link is limited to
100 devices or 100 zones.
The GRAFIK Eye QS control unit supplies
3 Power Draw Units (PDUs) on the QS link. Refer
to the QS Link Power Draw Units specification
submittal (Lutron P/N 369405) for more information
concerning Power Draw Units.
®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 9
Wiring the GRAFIK Eye QS with EcoSystem Control Unit (continued)
QS Link Control Wiring Details
QS smart
power
panel
LUTRON
LUTRON
LUTRON
LUTRONLUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
T-Tap Wiring Example
GRAFIK Eye QS
with EcoSystem
control unit
Sivoia QS
shade/drape
seeTouch QS
wallstation
To EcoSystem link 1
To EcoSystem
link 2
LUTRON
LUTRON
LUTRON
LUTRONLUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
GRAFIK Eye QS
with EcoSystem
control unit
Sivoia
QS
shade/
drape
seeTouch QS
wallstations
Daisy-Chain Wiring Example
QS smart
power panel
To EcoSystem link 2
To EcoSystem link 1
GRAFIK Eye QS
with EcoSystem
control unit
Wire Sizes (check compatibility in your area)
QS Link Wiring Length Wire Gauge Lutron Cable Part Number
Less than 500 ft (153 m) Power (terminals 1 and 2); 1 pair 18 AWG (1.0 mm2) GRX-CBL-346S (non-plenum)
GRX-PCBL-346S (plenum)
Data (terminals 3 and 4); 1 twisted, shielded pair 22 AWG (0.5 mm2)
Up to 2000 ft (610 m) Power (terminals 1 and 2); 1 pair 12 AWG (4.0 mm2) GRX-CBL-46L (non-plenum)
GRX-PCBL-46L (plenum)
Data (terminals 3 and 4); 1 twisted, shielded pair 22 AWG (0.5 mm2)
Notes:
• For more information regarding Lutron cable specifications, please see Lutron P/N 369596 and P/N 369597 at www.lutron.com
• For wire runs over 2000 ft (610 m), please contact Lutron Customer Assistance

®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 10
1234
12 ABC
4
3
2
1
4
3
2
1
4
3
2
1
4
3
2
1
Wiring the GRAFIK Eye QS with EcoSystem Control Unit (continued)
Powering More Than 3 Wallstations Example
• The +24 VDC wire from the power supply
connects to QS link terminal 2 on all of
the wallstations it is powering. This wire
does not connect to terminal 2 on the
GRAFIK Eye QS control unit.
The GRAFIK Eye QS with EcoSystem control unit can power up to 3 seeTouch wallstations. An external 24 V-power supply is
required to power more than 3 wallstations.
To power source
QSPS-P1-1-50
(powers up to 8 seeTouch QS
wallstations)
• The Common wire from the power supply
connects to QS link terminal 1 on all
of the wallstations it is powering and
terminal 1 on the GRAFIK Eye QS control
unit.
GRAFIK Eye QS with EcoSystem
control unit (rear view)
1 twisted pair
22 AWG
(0.5 mm2)
Lutron cable
GRX-CBL-346S-500 (non-plenum) or
GRX-PCBL-346S-500 (plenum)
seeTouch QS wallstations
(1) 18 AWG
(1.0 mm2)
Common
• The communication signals on the QS
link (terminals 3 and 4) connect from
the wallstations to the GRAFIK Eye QS
control unit on twisted, shielded cable
just as when an additional power supply
is not being used. Control unit shown in
rear view.

®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 11
Completing Installation of the GRAFIK Eye QS with EcoSystem Control Unit
1.Mount the control unit in the wallbox as
shown using the four screws provided.
Note: Follow all local and national
electrical codes when installing
IEC PELV/NEC®Class 2 wiring
with line voltage/mains wiring.
2.Verify installation:
•Restore power.
•Press the top scene button. The LED
will light.
•Press the zone raise and lower buttons.
Make sure the control unit is dimming all
connected loads.
3.Apply the protective overlay to the
control unit.
Note: When tightening mounting
screws, make sure that the
hinged cover and faceplate
will open fully, as shown.
Wall
7.9 in
(200 mm)
3.5 in
(87 mm) 3.75 in
(95 mm)
Protective overlay
(apply after installation)

The info screen turns off 30 seconds after the last button press or
completion of the last scene change. See example screens below.
The Master buttons activate the info screen. These buttons
temporarily raise or lower all dimmable lights (except those
programmed as unaffected in the current scene). Adjustments
are temporary and do not affect scene programming.
Note: Master buttons affect all zones.
The “OK” button activates the info screen (when off), which then
shows the current scene and its fade time. In “Save Always”
mode, it allows fade time adjustment. In “Save by OK” mode,
pressing a second time allows zone adjustment; pressing a
third time allows fade adjustment.
The Timeclock button activates the info screen and displays the
current time and the next event scheduled to occur. Pressing
a second time displays the time, date, and afterhours status.
Pressing a third time displays location and sunrise/sunset times.
Pressing a fourth time displays the language selection screen.
Pressing once more returns to the first screen.
The Page button is on 16-zone units only. Pressing the Page button will toggle the unit
between page 1 (zones 1 through 8) and page 2 (zones 9 through 16). Two LEDs above
each zone LED bar indicate the unit’s current page. Upon switching pages, the LED bars
for all 8 zones of that page will show their level for the current scene.
®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 12
OK
12345691011 12 13 14 7815
16
9-16
1-8
Scene 1
Master raise
Master lower
General Functionality
OK
12345691011 12 13 14 7815 16
9-16
1-8
OK
12345691011 12 13 14 7815 16
9-16
1-8
OK
12345691011 12 13 14 7815 16
9-16
1-8
Scene 1
Adjust fade
3seconds
OK
12345691011 12 13 14 7815 16
9-16
1-8
11:23 AM Fri
Next: 5:00 PM
Scene 1
Master buttons
“OK” button
Timeclock
(back) button
Page
button

Pre-Programmed Button Functionality
®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 13
OK
12345691011 12 13 14 7815 16
9-16
1-8
Scene Button Pre-Programming
for Dimmable Loads
Scene 1: All zones to 100%
Scene 2: All zones to 75%
Scene 3: All zones to 50%
Scene 4: All zones to 25%
All zones Off
OK
12345691011 12 13 14 7815 16
9-16
1-8
Shade Button Pre-Programming
for Sivoia QS shades
All shades fully open
All shades to 50%
All shades fully closed
Lower/Raise all shades
(Applies only to units with shade keypads)
The GRAFIK Eye QS with EcoSystem control unit controls most lighting loads without
special programming. Each unit ships with pre-programmed default settings for the
scene and shade buttons. For load types other than those shown below (dimmable
or non-dim), assign the load type before proceeding. See the scene setup section for
instructions on changing scene settings.

Zone Button Operation
Each zone column (LEDs and buttons)
represents one zone of lights. On 16-zone
units, the page button toggles between
zones 1 through 8 and zones 9 through
16. Page LEDs above each column will
indicate which zone is currently active on
the control unit. Pressing any button on
a column turns on the info screen and
displays the zone’s current light level and
current energy savings.
Pressing the raise and lower buttons on a
zone causes different actions depending
on zone type (see below).
Dimmable zones:
• Press and hold to raise/lower all lights in a
zone; release to stop
• Press raise or lower to stop a zone that is
fading
• Raising lights from off to full on or lowering
from full on to off takes 5 seconds
• Press raise and lower simultaneously to
toggle between full on and off
• Press and hold lower for 6 seconds after
the zone has gone to 0% light level to
set the zone as unaffected in the current
scene. The zone will not change when this
scene is initiated, and the Master buttons
will not raise/lower the zone in this scene.
Non-dim zones:
• Press raise to turn zone on
• Press lower to turn zone off
Note: To set zone types, see the zone
setup section.
®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 14
OK
12345
6
91011 12 13
14 7815 16
9-16
1-8
OK
12345691011 12 13 14 7815 16
9-16
1-8
Zone Raise
Zone Lower
Legend:
UA = Unaffected (lights are not affected by
scene button or Master buttons)
LED on
LED off
Zone LEDs
LEDs indicate
light level
(see below)
Zone LED Displays for % of Lighting Levels
Light Level
(%)
Off 1–17 18-33 34-49 50-66 67-82 83-99 On/
100
UA
Dimmable
Load Types
Non-Dim
Load Types

Entering and Exiting Programming Mode
Entering programming mode:
Press and hold the top and bottom scene
buttons simultaneously for 3 seconds. The
LEDs in the scene buttons will scroll from
top to bottom, confirming that you are in
programming mode, and the info screen
will display the main menu.
Exiting programming mode:
Press and hold the top and bottom scene
buttons simultaneously for 3 seconds. The
info screen will go to Scene 1.
Navigating Menus in Programming Mode
Master Buttons
The Master buttons allow you to move through the menu
choices. The current choice is highlighted on the info screen.
OK Button
The “OK” button chooses the current highlighted menu choice.
This will either take you to the next menu or accept a setting you
have selected. When the screen displays a Yes/No question, the
“OK” button is “Yes”.
Timeclock Button
The Timeclock button functions as a “back” button during
programming mode. Pressing the Timeclock button takes
you back one step in the current menu. Pressing it repeatedly
will eventually return you to the main menu, but will not exit
programming mode. When the screen displays a Yes/No
question, the Timeclock button is “No”.
®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 15
Programming Mode
OK
12345691011 12 13 14 7815
16
9-16
1-8
Press and hold the top and
bottom buttons for 3 seconds
to enter or exit programming
mode
Master buttons
“OK” button
Timeclock (back) button
Main menu
Scene setup
Timeclock
Scene 1
Fade time
3 seconds

®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 16
Wireless Mode
Many models of the GRAFIK Eye QS control unit support wireless communication with
other Lutron products. This feature allows for easy integration of wireless sensors,
keypads, remotes, and shades for single-room wireless applications
Units supporting wireless communication are labeled “GRAFIK Eye QS Wireless” on the
front label of the unit.
The wireless feature of the GRAFIK Eye QS Wireless control unit has three (3) modes of
operation.
• Ignore Programming (default): The GRAFIK Eye QS Wireless control unit will only
respond to normal operation commands from wireless devices associated while in
Enabled mode.
• Disabled: Use for wired-only systems.
• Enabled (30 minutes): The GRAFIK Eye QS Wireless control unit will respond to any
programming commands from nearby Lutron QS wireless (and compatible) products.
The GRAFIK Eye will automatically revert to “Ignore Programming” mode if there is no
activity for 30 minutes.
Changing the wireless mode of the GRAFIK Eye QS Wireless control unit:
1. Enter programming mode.
2. Use the Master buttons to highlight “Wireless Mode” and press
the “OK” button to accept.
3. Use the Master buttons to highlight the desired wireless mode,
and press the “OK” button to accept.
4. The info screen will display a confirming “Saved” message.
5. Exit programming mode.
Note: The wireless signal has a range of 30 ft (9 m) through
standard construction or 60 ft (18 m) line of sight.
Wireless Mode
Enabled (30 minutes)
Saved
Saved
Main menu
Shade labels
Wireless Mode
FCC Information
Changes or modifications not expressly approved
by Lutron Electronics Co. could void the user’s
authority to operate this equipment.
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
rules. Operation is subject to the following: (1)
This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
These limits are designed to provide reasonable
protection against harmful interference in a
residential and commercial installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio or television
reception. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
OK
12345691011 12 13 14 7815
16
9-16
1-8
Master
buttons
“OK”
button
Timeclock
(back) button

®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 17
Assigning Load Types
1. Enter programming mode.
2. Use the Master buttons to highlight
“Zone setup” and press the
“OK” button to accept.
3. Use the Master buttons to highlight
“Load type”. Press the “OK” button
to accept. See “Setting Load Types”
table on the next page.
4. Use the zone raise/lower buttons
to choose the load type for that
zone. See the list on the next page
for supported load types. Press the
“OK” button to accept.
5. The info screen will confirm that
your load type has been saved.
6. Exit programming mode.
Zone Setup
OK
12345691011 12 13 14 7815 16
9-16
1-8
Master
buttons
“OK” button
Main menu
CCI Setup
Zone setup
OK
12345691011 12 13
14 7815 16
9-16
1-8
Use the
zone raise/
lower
buttons to
choose the
load type for
that zone.
Zone Setup
Non-Dim Load Type
Load Type
Set zones
Saved
Load Type
Assigning Non-Dim Load Types
Zones assigned to non-dim loads have five available configurations:
•LOFO: Last On, First Off
•FOFO: First On, First Off
•FOLO: First On, Last Off
•LOLO: Last On, Last Off
•60/40: On at 60%, off at 40%
Scenes made up of both dim and non-dim
load types will toggle the non-dim loads
before the dim loads in a “First” on/off
configuration, and after the dim loads in a
“Last” on/off configuration.
1. Enter programming mode.
2. Use the Master buttons to highlight “Zone
setup” and press the “OK” button to accept.
3. Use the Master buttons to highlight “Non-Dim
Load type”. Press the “OK” button to accept.
See “Setting Load Types” table on the next
page.
4. Use the zone raise/lower buttons to choose
the non-dim load type for that zone. (Zones
not programmed as non-dim will be displayed
as Unaffected.) Press the “OK” button to accept.
5. The info screen will confirm that your load
type has been saved.
6. Exit programming mode.
Main menu
CCI Setup
Zone setup
Zone Setup
Load Type
Load Type
Set zones
Saved
Non-Dim Load Type

®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 18
Zone Setup (continued) Load Type Notes
• All electronic low-voltage (ELV) lighting
used with an interface must be rated for
reverse phase control dimming. Before
installing an ELV light source, verify with
the manufacturer that their transformer
can be dimmed. When dimming, an
ELV interface (e.g., PHPM-PA-DV-WH)
must be used with the control unit.
• For all DMX or RGB/CMY DMX lighting,
an external DMX interface (e.g.,
QSE-CI-DMX) must be used with the
control unit.
• Maximum total lighting load for Lutron
Tu-Wire and Advance Mark X electronic
dimming ballasts (120 V~only) must
not exceed 6 A per zone or 16 A per
unit.
• Maximum total lighting load for LTE LED
drivers must not exceed 10 LED drivers
per zone or 26 LED drivers per unit.
For non-EcoSystem loads:
• Not all zones must be connected;
however, connected zones must have a
minimum load:
120 V~: 25 W
220 - 240 V~: 40 W
• Maximum zone loads:
120 V~: 800 W
220 - 240 V~: 1200 W
• Maximum total lighting load for
magnetic low-voltage (MLV) varies by
input voltage:
120 V~: 800 VA / 600 W
220 - 240 V~: 1200 VA / 960 W
LUTRON
LUTRON LUTRON
LUTRON
Setting Load Types
Direct control via GRAFIK
Eye QS control unit
Control via power module
or interface
Fixture load type Choose this load type from the menu
on the GRAFIK Eye®QS control unit:
Zones 1 – 3
Incandescent Incandescent Power module
MLV (magnetic low-voltage) MLV Power module
ELV (electronic low-voltage) — Power module
Hi-Lume/Eco-10 ballast —Fluorescent module
Hi-lume 2-wire LTE LED driver Fluorescent module —
Hi-lume 3-wire L3D LED driver —Fluorescent module
0-10 V —Fluorescent module
Non-dim lighting loads Non-dim Non-dim
Neon/Cold cathode Neon, CC Neon, CC
Tu-Wire Tu-Wire Tu-Wire
Advance Mark XRTu-Wire Tu-Wire
EcoSystem Digital load —
DMX — DMX
RGB/CMY DMX —RGB/CMY DMX
EcoSystem switching (e.g., XPJ) Non-dim digital —
Cree LR4/LR6 LED Cree LR4/LR6 LED Fluorescent module
LED Incandescent* Power module
Zones 4 – 16
EcoSystem Digital load —
DMX — DMX
RGB/CMY DMX —RGB/CMY DMX
EcoSystem switching (e.g., XPJ) Non-dim digital —
* Use incandescent load type unless otherwise specified in the LED product selection tool available at www.lutron.com/ledtool.
To
EcoSystem
link
Power
module or
interface

Setting Minimum Level (optional)
Some local regulations specify a minimum lighting level for
dimming zones in occupied buildings. If this pertains to you,
follow these steps to set up your minimum lighting level.
1. Enter programming mode and select
“Zone setup,” then “Min level”. Press
the “OK” button to accept.
2. Use the Master buttons to highlight “Off”
if you want your lights to go all the way
off at their minimum light level, or “10%”
if you want that to be the minimum light
level. Press the “OK” button to accept.
Note: Non-dim loads will turn off
regardless of the minimum level setting.
3. The info screen will confirm that your
minimum level has been saved.
4. Exit programming mode.
®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 19
Zone Setup (continued)
Setting High End or Low End Trim
•If you are unsure about appropriate high and low end settings,
please contact Lutron Customer Assistance.
•High and low end trim settings limit the maximum and minimum
output of a dimming zone. Trim levels are set automatically when
the load type is programmed.
1. Enter programming mode.
2. Use the Master buttons to highlight
“Zone setup” and press the “OK” button
to accept.
3. Use the Master buttons to highlight
“High end” or “Low end” (this example
shows low end). Press the “OK” button to
accept.
4. Use the zone raise/lower buttons to
set the high end or low end trim for
that zone. The info screen will display
each zone number and percentage as
you adjust it. Press the “OK” button to
accept.
5. The info screen will confirm that your
setting has been saved.
6. Exit programming mode.
Main menu
CCI Setup
Zone setup
High end
Zone 2
Low end
Set zones
Low end
OK
12345691011 12 13 14 7815 16
9-16
1-8
Master
buttons
OK
12345691011 12 13
14 7815 16
9-16
1-8
Use the
zone raise/
lower
buttons to
set the high
end or low
end trim for
that zone.
“OK”
button
10%
Min level
Off
Zone setup
Low end
Min level
Zone setup
Saved Saved

®
GRAFIK Eye QS with EcoSystem Control Unit Installation and Operation Guide 20
Zone Setup (continued)
Labeling a Zone (optional)
1. Enter programming mode.
2. Use the Master buttons to highlight “Zone setup” and press
the “OK” button to accept.
3. Use the Master buttons to highlight “Label” and press the
“OK” button to accept.
4. Use the Master buttons to change the zone number to your
desired zone. Custom zone labels will appear if previously set.
Press the “OK” button to accept.
5. Use the Master buttons to highlight “Custom” and press the
“OK” button to accept. Or, highlight “Default” to return the
zone label to the default (e.g., Zone 1).
6. Use the Master buttons to scroll through the characters
(lowercase and uppercase letters, plus numbers 0 through 9).
The character you are currently changing will be underlined
on the screen. Press OK to select the character you want,
then repeat for all available characters. Choose a space (no
character) and press OK for any remaining characters. Press
the “OK” button to accept.
Note: Custom zone labels will always begin with the zone
number and a colon (e.g., 1: Uplights).
7. The info screen will confirm that your name has been saved.
8. Exit programming mode.
Note: On 16-zone units, use the page button to access all zones.
Main menu
CCI Setup
Zone setup
Min level
Label zone
Label
Label zone 2
Custom
Label zone 2
1: A
A
1 / 11
OK
12345691011 12 13 14 7815
16
9-16
1-8
Master
buttons
“OK”
button
Zone setup
Zone 2
Saved
Page button