Lutron Electronics QSE-IO User manual

RSPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
QS System QSE-IO Control Interface
369374a 1 08.07.12
QSE-IO Control Interface
The QSE-IO contact closure interface provides
integration with third-party equipment requiring
contact closure input/output, including occupancy
and vacancy sensors; motorized projection screens,
skylights, and window shades; AV equipment; security
systems; movable partition walls; and timeclocks. One
QSE-IO interface provides five (5) dry contact closure
outputs.
For complete functionality, programming
instructions, and detailed DIP switch settings, see
the QSE-IO Programming Guide, PN 040391,
at www.lutron.com/qs.
Key Features
•IntegratesaGRAFIKEye®QS control system
with equipment that has contact-closure I/O
•Providesveinputsandvedrycontactclosure
outputs.
•Providesbothnormallyopen(NO)andnormallyclosed
(NC)contacts.
•Maybeprogrammedtocontrolorbecontrolledby
anycombinationofGRAFIKEye®QS control units or
control any combination of Sivoia®QS window
treatments on the QS link.
Compatible Components
The following devices are compatible with the QS link.
Formoreinformationoneach,referto
www.lutron.com/qs.
•GRAFIKEye®QS control units
•seeTouch®QS wallstations
•Sivoia®QS shades
•QSInterfaces(contactclosure,Ethernet/RS232)
•Quantum®system
•EnergiSavrNodeTM units
•QSSensorModule
•QSKeyswitch
For Programming, see the
QSE-IO Control Interface Programming Guide:
PN 040391 at www.lutron.com/qs
Requirements
•QSLinkPowerSupply,suchasa:
 -GRAFIKEye®QS
 -QSLinkpowersupply,suchastheQSPS-P1-1-50
 -EnergiSavrNodeTM QS
- Quantum® light management hub
•QSCommunicationLink(IECPELV/NEC®Class2)
(seeQSLinkWireSizestable)

RSPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
QS System QSE-IO Control Interface
369374a 2 08.07.12
Specifications
Power
•IECPELV/NEC®Class2
•Operatingvoltage:12–24V 100mA
Regulatory Approvals
•ULListed
•cULListed
•CEcompliant
QS Link Limits
•TheQSwiredcommunicationslinkislimitedto
100devicesand100zones.EachQSE-IOcontrol
interfacecountsas1deviceand2zones.
•EachQSE-IOcontrolinterfaceconsumes3power
drawunits(PDU)ontheQSlink.RefertotheQS
LinkPowerDrawUnitsSpecicationSubmittal
(LutronPN369405,atwww.lutron.com)formore
information.
•ThemaximumwiringlengthfortheQSlinkis
2000ft(610m).
Environment
•32to104°F(0to40°C).
•Relativehumiditylessthan90%non-condensing.
Functionality and Operating Modes
•Usingtheinputs,contactclosuresinother
equipmentcanoperatecontrolunitsto:
–Selectscenes
 –Adjustscenestoreectstatusofmovablewalls
–Toggleanycombinationofzonesinthesystem
between Off and a configurable preset value
 –Turnlightsonoroffand/ormoveshadesbasedon
room occupancy
 –Performspecialfunctionssuchassequencing,
panic, control lockout, or timeclock disable
•Usingtheoutputs,sceneand/orzonechangesin
controlunitscan:
–Triggeroutputstocontrolotherequipment.
–Providestatusfeedbacktootherequipment.
•Usingtheinputs,contactclosuresinother
equipment can operate Sivoia®QS window
treatmentsto:
–Openorclose.
 –Raise,lower,orstop.
–Selectoneofthreeadjustablepresets.
•Usingtheoutputs,keypressesonQSwindow
treatmentkeypadsorGRAFIKEye®QS window
treatmentbuttonscan:
–Triggeroutputstoothermotorizedwindowtreatment
equipment.
•Sceneselection  •Occupancysensor
•Zonetoggle   •Shadeinput
•Specialfunctions  •Shadeoutput
•Partitioning
Five Input Terminals
•Acceptmaintainedinputsandmomentaryinputswith
40msecminimumpulsetimes.
•Off-stateleakagecurrentmustbelessthan100µA.
•Opencircuitvoltage:24V maximum.
•Inputsmustbedrycontactclosure,solidstate,open
collector,oractive-low(NPN)/activehigh(PNP)output.
 -OpencollectorNPNoractive-lowon-statevoltage
mustbelessthan2V andsink3.0mA.
 -OpencollectorPNPoractive-highon-statevoltage
mustbegreaterthan12V andsource3.0mA.
Five Output Terminals
•Provideselectablemaintainedormomentary
(1-second)outputs(IECPELV/NEC®Class2rated
only).
•TheQSE-IOisnotratedtocontrolunclamped,
inductive loads. Inductive loads include, but are not
limited to, relays, solenoids, and motors. To control
thesetypesofequipment,aybackdiodemustbe
used(DCvoltagesonly).See"TerminalLocations".
•Outputrelaysarenon-latching(ifrelaysareclosedand
power is lost, relays will open).
Status LEDs
•FiveStatusLEDslightwhenassociatedoutputis
active (on).

RSPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
QS System QSE-IO Control Interface
369374a 3 08.07.12
2.50
(63.5)
3.75
(95.3)
4.26
(108.2)
5.26
(133.6)
1.06
(26.9)
Mountingholes
Terminal
blocks
on this side
LEDsandaddressing
switches on this side
Dimensions
Dimensionsareininches(mm)
0.34
(8.6)dia.
0.18
(4.6)dia.
0.18
(4.6)dia.
0.25
(6.4)
#6or#8(M3orM4)
screw recommended
MountingHoleDetail
Mounting Options
Mounting Examples
Mountwhereterminalblocks,switches,andLEDsare
accessible. Strip 4in(10mm)ofinsulationfrom
wires. Each data link terminal will accept up to two
18AWG(1.0mm2)wires.Connectwiringasshownin
theWiringDiagram.Choosefromthefollowing
mountingmethods:
1: Direct Wall Mounting
Mountthecontrolinterfacedirectlyonawall,as
showninMountingMethodsatright,usingscrews
(notincluded).Whenmounting,providesufcient
space for connecting cables.
2: Rack Mounting
PlacetheunitcanintheLUT-19AV-1UAVrackusing
screws(notincluded).TheLUT-19AV-1Uwillholdup
to four units.
3: Enclosed Wall Mounting
If conduit is desired for wiring, use the
LUT-5x10-ENCtomountoneunit.
Note:Contactclosureoutputrelaysclickaudibly
whenswitching.Mountwherethiswillnotcause
inconvenience.
LUT-19AV-1U
2
LUT-5x10-ENC
5.26
4.263.75
2.50
1.06
Control Interface
Wall
1
3

RSPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
QS System QSE-IO Control Interface
369374a 4 08.07.12
Terminal Locations
4321
Relay 1 NC Relay 1 NO Relay 1 & 2 Common Relay 2 NC Relay 2 NO Relay 3 NC Relay 3 NO Relay 3 & 4 Common Relay 4 NC Relay 4 NO Relay 5 NC Relay 5 NO Relay 5 Common Input 1 Input 2 Input 3 Input 4 Input 5 Common
CCIandCCOterminalseachholdone
28–16AWG(0.08–1.5mm2) wire
QSDataLink(tocontrol
units, window treatments,
and wallstations)
 1:Common
 2:24V
 3:MUX
4:MUX
CCO 1 NC CCO 1 NO 1-2 COM CCO 2 NC CCO 2 NO CCO 3 NC CCO 3 NO 3-4 COM CCO 4 NC CCO 4 NO CCO 5 NC CCO 5 NO 5 COM CCI 1 CCI 2 CCI 3 CCI 4 CCI 5 COM
QSE-IO
Program
button
1234567
DIPswitches
LED1:CCO1
LED2:CCO2
LED3:CCO3
LED4:CCO4
LED5:CCO5
LED6:Unused
LED7:Status
Note:LEDisONwhenCCONO
(normally open contact) is closed.
}
ContactClosureOutputs Contact
Closure
Inputs
LED and DIP Switch Locations
QS Link Wire Sizes (check compatibility in your area)
QS Link Wiring Length Wire Gauge Lutron Cable Part Number
<500ft(153m)
Power(terminals1and2)
1pair18AWG(1.0mm2)GRX-CBL-346S(non-plenum)
GRX-PCBL-346S(plenum)
Data(terminals3and4)
1twisted,shieldedpair22AWG(0.5mm2)
500–2000ft
(153–610m)
Power(terminals1and2)
1pair12AWG(4.0mm2)GRX-CBL-46L(non-plenum)
GRX-PCBL-46L(plenum)
Data(terminals3and4)
1twisted,shieldedpair22AWG(0.5mm2)

RSPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
QS System QSE-IO Control Interface
369374a 5 08.07.12
QS Link Wiring Methods (choose one)
Powered by GRAFIK Eye®QS Control Unit
Powered by a QS Link Power Supply
1234
12 ABC
123456LN
To additional wallstations/
control interfaces
To additional wallstations/
control interfaces
RearViewof
GRAFIKEye®QS
ControlUnit
RearViewof
GRAFIKEye®QS
ControlUnit
QS
Link
QS
Link
QSLink
1:Common
2:Power
3:MUX
4:MUX
DataLink:
4:MUX
3:MUX
SeeQSLink
WireSizestable
previous page
IECPELV/NECClass2Powerwiring:
2:Power
1:Common
SeeQSLinkWireSizes
table previous page
•SystemcommunicationusesIECPELV/NEC®Class2
wiring.
•Followalllocalandnationalelectricalcodeswhen
installingIECPELV/NEC®Class2wiringwithline
voltage/mains wiring.
•Eachterminalacceptsuptotwo18AWG(1.0mm²)
wires.
•Totallengthofcontrollinkmustnotexceed2000ft
(610m).
•TypicalWireSizes:SeeQSLinkWireSizestable,
previous page.
•Connecttheterminal1,3,and4connectionstoall
control units, wallstations, and control interfaces in
theQSsystem.Forterminal2connectivity,please
refer to the wiring diagrams below.
•TheQSE-IOcontrolinterfacecanbepoweredbythe
followingdevices:
 -GRAFIKEye®QS control unit
 -QSlinkpowersupply(QSPSmodelnumbers)
- Quantum®LightManagementHub
(see Quantum®system documentation)
 -EnergiSavrNodeTM QS
4321
LutronCable
SeeQSLinkWireSizestable
previous page
QSPS-P1-1-50
(providesupto8
power draw units)
To power source
(1)18AWG
(1.0mm2)
Common
(1)twistedpair
22AWG
(0.5mm2)

RSPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
QS System QSE-IO Control Interface
369374a 6 08.07.12
Wiring Application Examples
1 Lutron Occupancy Sensor Wired to 1 QSE-IO Device Input
QSE-IO Terminals
Occupancy
Sensor
Power Pack
(use model that
corresponds to
input voltage)
Hot
Neutral
Red (+20 - 24 V )
Blue (signal)
Black (common)
Blue (signal)
Black
(common)
Black
White
Red
Red
120 / 277 / 347 V 60 Hz
230 V 50 / 60 Hz
CCI1 CCI2 CCI3 CCI4 CCI5 COM
Power Pack
(use model that
corresponds to
input voltage)
Blue (signal)
Black
(common)
3 Lutron Occupancy Sensors Wired to 1 QSE-IO Device Input
QSE-IO Terminals
Occupancy
Sensors
Hot
Neutral
Red (+20 - 24 V )
Blue (signal)
Black (common)
Black
White
Red
Red
120 / 277 / 347 V 60 Hz
230 V 50 / 60 Hz
CCI1 CCI2 CCI3 CCI4 CCI5 COM
Note: Occupancy sensors will not participate in partitioning logic.
More Than 3 Lutron Occupancy Sensors Wired to 1 QSE-IO Device Input
QSE-IO Terminals
Occupancy Sensors
Hot
Neutral
Red (+20 - 24 V )
Blue (signal)
Black (common)
Red (+20 - 24 V )
Blue (signal)
Black (common)
Black
White
Red
Red
120 / 277 / 347 V 60 Hz
230 V 50 / 60 Hz
CCI1 CCI2 CCI3 CCI4 CCI5 COM
Occupancy Sensors
Hot
Neutral
Black
White
Red
Red
120 / 277 / 347 V 60 Hz
230 V 50 / 60 Hz
Blue (signal)
Black
(common)
Blue (signal)
Black
(common)
Power Pack
(use model that
corresponds to
input voltage)
Power Pack
(use model that
corresponds to
input voltage)
Note: Occupancy sensors will not participate in partitioning logic.

RSPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
QS System QSE-IO Control Interface
369374a 7 08.07.12
Multiple Lutron Occupancy Sensors Wired to Multiple QSE-IO Device Inputs
QSE-IO Terminals
Occupancy Sensors
Hot
Neutral
Red(+20-24V )
Blue(signal)
Black(common)
Red(+20-24V )
Blue(signal)
Black(common)
Black
White
Red
Red
120/277/347V 60Hz
230V 50/60Hz
CCI1 CCI2 CCI3 CCI4 CCI5 COM
Occupancy Sensors
Power
Pack*
Hot
Neutral
120/277/347V 60Hz
230V 50/60Hz
Occupancy Sensors
Power
Pack*
Neutral
120/277/347V 60Hz
230V 50/60Hz
Hot
Occupancy Sensor
Power
Pack*
Neutral
120/277/347V 60Hz
230V 50/60Hz
Hot
Black
White
Red
Red
Black
White
Red
Red
Black
White
Red
Red
Black
White
Red
Red
Occupancy Sensor
Power
Pack*
Neutral
120/277/347V 60Hz
230V 50/60Hz
Hot
Red(+20-24V )
Blue(signal)
Black(common)
Red(+20-24V )
Blue(signal)
Black(common)
Red(+20-24V )
Blue(signal)
Black(common)
Wiring Application Examples
Power
Pack*
*(usepower
pack model that
corresponds to
input voltage)
Note:Occupancysensorswillnotparticipateinpartitioninglogic.

RSPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
QS System QSE-IO Control Interface
369374a 8 08.07.12
QSE-IO Operating Modes and DIP Switch Settings Overview
Mode Dip Switch Contact Closures Invoke:
Configuration 3 4 5 6 7 8 Input 1 Input 2 Input 3 Input 4 Input 5 Inputs Outputs
Scene selection
Scene 1 Scene 2 Scene 3 Scene 4 Scene Off
Maintained or
Momentary Maintained
Scene 5 Scene 6 Scene 7 Scene 8 Scene Off
Scene 9 Scene 10 Scene 11 Scene 12 Scene Off
Scene 13 Scene 14 Scene 15 Scene 16 Scene Off
Scene 1 Scene 2 Scene 3 Scene 4 Scene Off
Maintained or
Momentary Momentary
Scene 5 Scene 6 Scene 7 Scene 8 Scene Off
Scene 9 Scene 10 Scene 11 Scene 12 Scene Off
Scene 13 Scene 14 Scene 15 Scene 16 Scene Off
Special
(maintained)
Sequence
5–16
Zone
lockout
Scene
lockout
Panic
mode Timeclock Maintained
Maintained
Special
(momentary)
Sequence
5–16
Zone
lockout
Scene
lockout
Panic
mode Timeclock Momentary
Special 2
(maintained)
Sequence
1–4
Zone
lockout
Scene
lockout
Panic
mode
Afterhours
mode Maintained
Maintained
Special 2
(momentary)
Sequence
1–4
Zone
lockout
Scene
lockout
Panic
mode
Afterhours
mode Momentary
Shade input preset
(“stop if moving”) Shade
open
Shade
preset 1
Shade
preset 2
Shade
preset 3
Shade
close
Maintained or
Momentary Maintained
Shade input preset
(no “stop if moving”)
Shade input
(raise, lower, stop)
Shade
open
Shade
raise
Shade
lower Shade stop Shade close
Momentary or
Maintained Maintained
Shade input dual group
(“stop if moving”) Open
Group 1
Close
Group 1
Open
Group 2
Close
Group 2 —Maintained or Momentary Maintained
Shade input dual group
(no “stop if moving”)
Shade input dual group
(raise/lower)
Raise/Stop
Group 1
Lower/Stop
Group 1
Raise/Stop
Group 2
Lower/Stop
Group 2 —Momentary Momentary
Shade input toggle
(“stop if moving”:
open/stop/close/stop)
Toggle
Group 1
Toggle
Group 2
Toggle
Group 3
Toggle
Group 4
Toggle
Group 5 Momentary Momentary
Shade input toggle
(no “stop if moving”:
open/close)
Toggle
Group 1
Toggle
Group 2
Toggle
Group 3
Toggle
Group 4
Toggle
Group 5 Maintained Momentary
AC Shade output
(maintained outputs)
Open
Group 1
Stop Group
1
Close
Group 1
Open
Group 2
Close
Group 2
Maintained or
Momentary Maintained
AC Shade output
(momentary stop)
Open
Group 1
Stop Group
1
if moving
Close
Group 1
Open
Group 2
Close
Group 2
Maintained or
Momentary
Maintained
(except 2, which
is Momentary)
AC Shade output
(momentary outputs)
Open
Group 1
Stop Group
1
if moving
Close
Group 1
Open
Group 2
Close
Group 2
Maintained or
Momentary Momentary
Notes
• ForACshadeswithonly2inputs(open/close),setDIPswitch1totheup/onpositiontoenablethefeature
thatmimics“stop”(assertsboth“open”and“close”CCOstogetherwhena“stop”commandisreceived).
• TheQSE-IOprovidesnopower,onlyacontrolsignal,toACshades.Refertotheinstructionsthatcamewithyourshadesformore
information.
Legend:
Up/On
Down/Off
scene
selection
special and
special 2
zone
toggle
zone
control
hotel
conguration
integration
conguration
shade
stuffs
partitioning
occ sensor
345678345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678345678
345678
345678
345678
345678
345678
345678
345678
345678

RSPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
QS System QSE-IO Control Interface
369374a 9 08.07.12
QSE-IO Operating Modes and DIP Switch Settings Overview (continued)
Mode Dip Switch Contact Closures Invoke:
Configuration 3 4 5 6 7 8 Input 1 Input 2 Input 3 Input 4 Input 5 Inputs Outputs
Partitioning
(momentary) Wall 1 Wall 2 Wall 3 Wall 4 Wall 5 Momentary Maintained
Partitioning
(maintained) Wall 1 Wall 2 Wall 3 Wall 4 Wall 5 Maintained Maintained
Occupancy sensor
(auto on/off) Generates events on occupancy and vacancy Maintained Maintained
Occupancy sensor
(manual on/auto off) Generates events on vacancy only Maintained Maintained
Zone toggle
(maintained) Toggle 1 Toggle 2 Toggle 3 Toggle 4 Toggle 5 Maintained
Maintained
Zone toggle
(momentary) Toggle 1 Toggle 2 Toggle 3 Toggle 4 Toggle 5 Momentary
Zone toggle with raise/lower
(maintained) Toggle 1 Toggle 2 Toggle 3 Raise Lower Maintained
Zone toggle with raise/lower
(momentary) Toggle 1 Toggle 2 Toggle 3 Raise Lower Momentary
Zone control
(maintained output)
Toggle 1 Toggle 2 Toggle 3 Toggle 4 Toggle 5 Maintained
Maintained
Toggle 1 Toggle 2 Toggle 3 Toggle 4 Toggle 5 Momentary
Zone control
(momentary output)
Pulse 1 Pulse 2 Pulse 3 Pulse 4 Pulse 5 Maintained
Momentary
Pulse 1 Pulse 2 Pulse 3 Pulse 4 Pulse 5 Momentary
Zone control
(pulsed output)
Pulse 1 Pulse 2 Pulse 3 Pulse 4 Pulse 5 Maintained
Pulsed
Pulse 1 Pulse 2 Pulse 3 Pulse 4 Pulse 5 Momentary
Hotel configuration 1
Service
(make up
room)
Privacy
(do not
disturb)
Doorbell
Start/end
afterhours
mode
Toggle
Scene 1/
Off
1-3:
Maintained or
Momentary
4-5:
Maintained
Maintained
(except 3)
Hotel configuration 2
Service
(make up
room)
Privacy
(do not
disturb)
Doorbell
Start/end
afterhours
mode
Enable/
disable
Scene
lockout
1-3:
Maintained or
Momentary
4-5:
Maintained
Maintained
(except 3)
Integration configuration Control
output 1
Control
output 2
Control
output 3
Control
output 4
Control
output 5
Maintained or
Momentary
Maintained or
Momentary
Notes
• Occupancysensor:Eachinputrepresents1sensor/groupofsensors.Responsetosensoreventisprogrammableattheassignedlighting
control.
• “Momentary”outputpulseisoffixedduration(250msdefault).
“Pulsed”outputdurationcorrespondstoactivatingbuttonbeingheld/released.
• Hotel:“Service”and“Privacy”aremutuallyexclusive;“Doorbell”islockedoutwhen“Privacy”isactive.
• DIPswitch1mustbeup/ontoactivatethe"Start/EndAfterhours"featureonCCI4.
• DIPswitch2mustbeup/ontoactivatethe"ToggleScene"or"SceneBlackout"featureonCCI5.
• Occupancysensorswillnotparticipateinpartitioninglogic.
Legend:
Up/On
Down/Off
scene
selection
special and
special 2
zone
toggle
zone
control
hotel
conguration
integration
conguration
shade
stuffs
partitioning
occ sensor
345678345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678
345678345678
345678
345678
345678
345678
345678
345678
345678
345678