Lutron Electronics GRAFIK Eye QSGRJ-3P Operating instructions

LUTRON
Control Unit
Installation and Operation Guide
®
Please Read
The GRAFIK Eye®QS control unit allows for
control of both lights and shades, without
interfaces, using a single control unit.
Features include pushbutton scene recall,
info screen that displays energy savings and
status, IR receiver, astronomic timeclock,
contact closure input, and engravable
backlit buttons that are easy to find and
operate.
Model Numbers: QSGRJ-3P, QSGRJ-4P, QSGRJ-6P
QSGR-3P, QSGR-4P, QSGR-6P
120 V~50/60 Hz 220 - 240 V~50/60 Hz
Unit Capacity (watts) 2000 W 3000 W
MLV 2000 VA / 1600 W 3000 VA / 2400 W
Zone Capacity (watts) 25 – 800 W 40 – 1200 W
MLV 25 – 800 VA / 25 – 600 W 40 – 1200 VA / 40 – 960 W
See page 7 for IEC PELV/NEC®Class 2 ratings.
For California residents only:
The batteries in these devices contain
Perchlorate Material – special handling may apply.
For more information visit
www.dtsc.ca.gov/hazardouswaste/perchlorate
English Español Français

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 2
Contents
Features and Functions of the
GRAFIK Eye®QS Control Unit .................3
Wiring the GRAFIK Eye®QS Control Unit
Overview of Line Voltage/Mains Wiring .........4
Line Voltage Wiring Details...................5
Overview of IEC PELV/NEC®Class 2 Wiring .....7
QS Link Control Wiring Details................8
Powering More Than 3 Wallstations Example....9
Completing Installation of the
GRAFIK Eye®QS Control Unit ............10
General Functionality ...................11
Pre-Programmed Button Functionality .....12
Zone Button Operation
Zone LED Displays for % of Lighting Levels....13
Programming Mode
Entering and Exiting Programming Mode ......14
Navigating Menus in Programming Mode ......14
Wireless Mode.........................15
FCC Information ..........................15
Zone Setup
Assigning Load Types......................16
Assigning Non-Dim Load Types..............16
Setting Load Types ........................17
Setting High End or Low End Trim............18
Setting Minimum Level (optional).............18
Labeling a Zone (optional) ..................19
Scene Setup
Setting Zone Levels, Fade Rates,
and Shade Group Actions ..................20
Labeling a Scene (optional) .................21
Enabling/Disabling Daylighting in a Scene .....21
Setting Save Mode
Save Mode Settings .......................22
Quick Scene Programming:
Save by OK Mode .........................22
Contact Closure Input (CCI) Setup.........23
Occupancy Sensor Setup................25
Associating Wireless Occupancy Sensors .....26
Selecting the Mode ........................27
Scene Mode .............................28
Zone Mode ..............................29
Labeling an Occupancy Sensor (optional)......30
Configuring Occupancy Sensor Settings
(optional) ................................31
Daylight Sensor Setup ..................32
Associating Wireless Daylight Sensors ........33
Assigning Sensors.........................34
Calibrating Sensors........................34
Labeling a Daylight Sensor (optional) .........35
Pico®Wireless Control Setup .............36
Associating with a GRAFIK Eye®QS
Wireless Control Unit ......................37
Associating through a QS Sensor Module .....38
IR Setup ..............................39
Enabling/Disabling the IR Receiver ...........40
Associating the QS IR Eye with a
GRAFIK Eye®QS Control Unit ...............41
Associating through a QS Sensor Module .....43
Associating Sivoia®QS Shades/Drapes
and GRAFIK Eye®QS Control Units ........44
Adjusting Shade Settings
Setting Limits.............................45
Preset Adjustment: Simple Method ...........46
Preset Adjustment: Advanced Method ........46
Naming a Group of Shades .................47
Enable/Disable “Stop If Moving” Functionality . . 48
Associating Sivoia®QS Triathlon®Shades with
GRAFIK Eye®QS Control Unit . . . . . . . . . 49
Setting Upper and Lower Limits of a
Sivoia®QS Triathlon®Shade with
GRAFIK Eye®QS Control Unit . . . . . . . . . 50
Associating Multiple GRAFIK Eye®QS
Control Units ..........................51
Timeclock Operation
Setting Time and Date .....................52
Setting Location ..........................53
Setting Daylight Saving Time ................53
Adding an Event ..........................54
Deleting an Event .........................55
Viewing an Event..........................55
Setting a Holiday ..........................56
Viewing a Holiday .........................56
Deleting a Holiday .........................56
Copying a Schedule .......................57
Deleting a Schedule .......................57
Afterhours ............................58
Afterhours Examples.......................59
Setting Up Afterhours ......................60
Ending Afterhours .........................60
Diagnostics and Special Settings
Enabling/Disabling the Timeclock ............61
Enabling/Disabling the Backlighting ..........61
Diagnostics ..............................61
Setting the Security Password ...............62
Language Selection ....................63
Faceplate Removal . . . . . . . . . . . . . . . . . . . . . 63
Troubleshooting .......................64
Troubleshooting: Wireless Functions.......65
Troubleshooting: Shade Functions ........66
Warranty .............................67
Contact Information ....................67

OK
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 3
Optional Shade
button groups
Preset and raise/lower
buttons with integral LEDs
(maximum of 3 button
groups)
Zone numbers
Zone raise/lower buttons
Zone LEDs display current
lighting zone levels
Hinged faceplate
Hinged faceplate
Features and Functions of the GRAFIK Eye®QS Control Unit
Info screen
Displays status or
programming functions
Scene buttons
With integral scene
indicator LEDs
Timeclock button
Displays current
timeclock info
“OK” button
Used for programming
Infrared receiver
For handheld remote use
Master buttons
Temporarily raise and lower
lighting levels on unit
USB Receptacle for PC programming: Micro or Mini B
(To access micro USB receptacle, pull down to remove
lower hinged faceplate)

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 4
Wiring the GRAFIK Eye®QS Control Unit
Overview of Line Voltage/Mains Wiring
1234
12 ABC
123456LN
12 AWG (4.0 mm2)
each terminal
120 - 127 V~
or
220 - 240 V~
Distribution
Panel
Line Voltage/Mains
Cables and Load Wiring
123456LN
Incandescent load
Load controlled
by power module
or interface
Terminal labels:
L: Hot/Live
N: Neutral
: Ground
1-6: Dimmed/Switched
line voltage outputs
Power module
or interface

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 5
Wiring the GRAFIK Eye®QS Control Unit (continued)
Line Voltage Wiring Details
• Use properly certified cable for all line
voltage/mains cables.
• Proper short-circuit and overload
protection must be provided at the
distribution panel. You can use up to a
20 A circuit breaker for your installation.
• Install in accordance with all local and
national electrical codes.
• IEC PELV/NEC®Class 2 terminals may
be temporarily unplugged for ease of IR,
occupancy sensor, and control wiring.
• Notice: Risk of damage to unit. Do not
connect line voltage/mains cable to IEC
PELV/NEC®Class 2 terminals.
Step 1: Install wallbox. Mount a 3½ in
(89 mm) deep 4-gang U.S. wallbox on a
dry, flat indoor surface that is accessible
and allows for system programming and
operation. Allow at least 4½ in (110 mm)
clearance above and below the faceplate
to ensure proper heat dissipation. Allow
1 in (25 mm) for faceplate overhang on
all sides.
Note: 4-gang wallbox available from
Lutron; P/N 241400.
Step 2: Test load wiring.
• Turn power OFF at the circuit breaker or
fuse box.
• Connect a standard light switch between
the live lead and load wire to test the
circuit.
• Turn power ON and check for short or
open circuits. If load does not operate,
the circuit is open. If the circuit breaker
trips (fuse blows or opens), a load short
may exist. Correct short or open circuits
and test again.
`
Step 3: Check control unit wiring.
•Earth/ground terminal connection must
be made as shown in line voltage wiring
diagrams.
•Do not mix different load types on the
same zone.
• Follow all local and national electrical
codes when installing IEC PELV/
NEC®Class 2 wiring with line voltage/
mains wiring.
WARNING! Shock hazard. May
result in serious injury or death.
Always turn off circuit breaker or
remove main fuse from power line
before doing any work. Before
connecting the loads to the
GRAFIK Eye®QS control unit, test
the loads for short-circuits.
Neutral
Hot/Live Switch
Load
LUTRON
LUTRON
Faceplate overhangs
wallbox on all sides;
allow 1 in (25 mm)
4`in
(110 mm)

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 6
Wiring the GRAFIK Eye®QS Control Unit (continued)
Line Voltage Wiring Details
Step 4: Connect line voltage and loads
to control unit.
• Strip 9in (8 mm) of insulation off the line
voltage/mains cables in the wallbox.
• Connect the line voltage/mains, ground,
and load wires to the appropriate
terminals on the back of the control unit.
L: Hot/Live
N: Neutral
: Ground
Terminals 1-6: Dimmed/Switched
line voltage outputs
9in
(8 mm)
The recommended installation torque is
5.0 in∙lb (0.6 N∙m) for line voltage/mains
connections and 5.0 in∙lb (0.6 N∙m) for
the earth/ground connection.
Note: See the zone setup section for a
list of compatible load types and
instructions for programming the
GRAFIK Eye®QS control unit to
properly recognize them.
Notice: Risk of damage to unit. GRAFIK Eye®QS control units must be installed by a
qualified electrician in accordance with all applicable regulations and building codes.
Improper wiring can result in damage to control units or other equipment.
Note: To avoid overheating and possible damage to equipment, do not install control
units to dim receptacles, motor-operated appliances, or fluorescent lighting not
equipped with LutronRHi-lume®, Eco-10®, Tu-Wire®, electronic dimming ballasts, or
other devices approved for your location. In dimmed magnetic low-voltage circuits,
you can prevent transformer overheating and failure by avoiding excessively high
current flow. Do not operate control units with any lamps removed or burned out;
replace any burned out lamps immediately; use only transformers that incorporate
thermal protection or fused primary windings. Control units are designed for residential
and commercial use, for indoor use only.

1234
12 ABC
123456LN
Contact Closure Input Wiring
24 V-50 mA
For settings, see CCI Mode Setup.
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 7
1234
12
ABC
Example:
Occupancy sensor
(maximum 1)
1: COM
2: 24 V-*
3: MUX
4: MUX
Wiring the GRAFIK Eye®QS Control Unit (continued)
Overview of IEC PELV/NEC®Class 2 Wiring
IR Wiring
From external
IR connection
(by others)
18 AWG (1.0 mm2)
each terminal
18 AWG (1.0 mm2)
each terminal
1: IR DATA
2: IR COM
A: CCI SIG
B: 24 V-
C: CCI COM
To control stations,
shades, or other
GRAFIK Eye®QS
control units
Data (terminals 3 and 4):
Twisted, shielded pair 22 AWG (0.5 mm2)
each terminal
*Do not connect terminal 2
between any GRAFIK Eye®
QS control unit and any other
power supply, including another
GRAFIK Eye®QS control unit.
Refer to the QS Link Power Draw
Units specification submittal
(LutronRP/N 369405) for more
information concerning PDUs.
ABC
Example:
Emergency lighting interface (maximum 1)
Note: The GRAFIK Eye®QS control unit
must be powered by a Normal/Emergency
distribution panel for proper ELI operation.
Refer to the LUT-ELI-3PH Installation Guide
for the complete wiring diagram.
A: CCI SIG
B: 24 V-
C: CCI COM
LUT-ELI-3PH
Signal
+V Input
Circuit Common
Note: Use appropriate wire connecting devices
as specified by local codes.
QS Link Control Wiring
24 V-100 mA
Common and power (terminals 1 and 2):
Two 18 AWG (1.0 mm2) each terminal (for link <500 ft/153 m)
Two 12 AWG (4.0 mm2) each terminal (for link 500-2000 ft/153-610 m)

• System communication uses IEC PELV/NEC®
Class 2 wiring.
• Follow all local and national electrical codes when
installing IEC PELV/NEC®Class 2 wiring with line
voltage/mains wiring.
• Each terminal accepts up to two 18 AWG (1.0 mm2)
wires.
• Total length of control link must not exceed
2000 ft (610 m).
• Make all connections in the control unit’s wallbox.
• Wiring can be T-tapped or daisy-chained.
• IEC PELV/NEC®Class 2 24 V-150 mA.
System Limits
The QS wired communication link is limited
to 100 devices or 100 zones.
The GRAFIK Eye®QS control unit supplies
3 Power Draw Units (PDUs) on the QS link. Refer
to the QS Link Power Draw Units specification
submittal (LutronRP/N 369405) for more information
concerning Power Draw Units.
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 8
Wiring the GRAFIK Eye® QS Control Unit (continued)
QS Link Control Wiring Details
QS smart
power
panel
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
T-Tap Wiring Example
GRAFIK Eye®QS
control unit
Sivoia®QS
shade/drape
seeTouch®QS
wallstation
LUTRON
LUTRON
LUTRON
LUTRONLUTRON
LUTRON
LUTRON
GRAFIK Eye®QS
control unit
Sivoia®
QS
shade/
drape
seeTouch®QS
wallstations
Daisy-Chain Wiring Example
QS smart
power panel
GRAFIK Eye®QS
control unit
Wire Sizes (check compatibility in your area)
QS Link Wiring Length Wire Gauge LutronRCable Part Number
Less than 500 ft (153 m) Power (terminals 1 and 2); 1 pair 18 AWG (1.0 mm2) GRX-CBL-346S (non-plenum)
GRX-PCBL-346S (plenum)
Data (terminals 3 and 4); 1 twisted, shielded pair 22 AWG (0.5 mm2)
Up to 2000 ft (610 m) Power (terminals 1 and 2); 1 pair 12 AWG (4.0 mm2) GRX-CBL-46L (non-plenum)
GRX-PCBL-46L (plenum)
Data (terminals 3 and 4); 1 twisted, shielded pair 22 AWG (0.5 mm2)
Notes:
• For more information regarding LutronRcable specifications, please see LutronRP/N 369596 and P/N 369597 at www.lutron.com
• For wire runs over 2000 ft (610 m), please contact LutronRTechnical Support

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 9
1234
12 ABC
4
3
2
1
4
3
2
1
4
3
2
1
4
3
2
1
123456LN
Wiring the GRAFIK Eye®QS Control Unit (continued)
Powering More Than 3 Wallstations Example
• The +24 VDC wire from the power supply
connects to QS link terminal 2 on all of
the wallstations it is powering. This wire
does not connect to terminal 2 on the
GRAFIK Eye®QS control unit.
The GRAFIK Eye®QS control unit can power up to 3 seeTouch®wallstations. An external 24 V-power supply is required to power
more than 3 wallstations.
To power source
QSPS-P1-1-50
(powers up to 8 seeTouch®QS
wallstations)
• The Common wire from the power
supply connects to QS link terminal 1
on all of the wallstations it is powering
and terminal 1 on the GRAFIK Eye®QS
control unit.
GRAFIK Eye®QS control unit
(rear view)
1 twisted pair
22 AWG
(0.5 mm2)
LutronRcable
GRX-CBL-346S-500 (non-plenum) or
GRX-PCBL-346S-500 (plenum)
seeTouch®QS wallstations
(1) 18 AWG
(1.0 mm2)
Common
• The communication signals on the QS
link (terminals 3 and 4) connect from
the wallstations to the GRAFIK Eye®QS
control unit on twisted, shielded cable
just as when an additional power supply
is not being used. Control unit shown in
rear view.

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 10
Completing Installation of the GRAFIK Eye®QS Control Unit
1.Mount the control unit in the wallbox as
shown using the four screws provided.
Note: Follow all local and national
electrical codes when installing IEC
PELV/NEC®Class 2 wiring with line
voltage/mains wiring.
2.Verify installation:
• Restore power.
• Press the top scene button. The LED
will light.
• Press the zone raise and lower buttons.
Make sure the control unit is dimming all
connected loads.
3.Apply the protective overlay to the
control unit.
Note: When tightening mounting
screws, make sure that the hinged
cover and faceplate will open fully,
as shown.
Wall
7.9 in
(200 mm)
3.5 in
(87 mm) 3.75 in
(95 mm)
Protective overlay
(apply after installation)
Note: To access micro USB
receptacle, pull down to remove
lower hinged faceplate.

OK
The info screen turns off 30 seconds after the last button press or
completion of the last scene change. See example screens below.
The Master buttons activate the info screen. These buttons
temporarily raise or lower all dimmable lights (except those
programmed as unaffected in the current scene). Adjustments are
temporary and do not affect scene programming.
Note: Master buttons affect all zones.
The “OK” button activates the info screen (when off), which then
shows the current scene and its fade time.
In “Save Always”
mode, it allows fade time adjustment. In “Save by OK” mode,
pressing a second time allows zone adjustment; pressing a
third time allows fade adjustment.
The Timeclock button activates the info screen and displays the
current time and the next event scheduled to occur. Pressing
a second time displays the time, date, and afterhours status.
Pressing a third time displays location and sunrise/sunset times.
Pressing a fourth time displays the language selection screen.
Pressing once more returns to the first screen.
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 11
Scene 1
Master raise
Master lower
General Functionality
OK Scene 1
Adjust fade
3seconds
11:23 AM Fri
Next: 5:00 PM
Scene 1
Master buttons
“OK” button
Timeclock
(back) button

Pre-Programmed Button Functionality
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 12
Scene Button Pre-Programming
for Dimmable Loads
Scene 1: All zones to 100%
Scene 2: All zones to 75%
Scene 3: All zones to 50%
Scene 4: All zones to 25%
All zones Off
Shade Button Pre-Programming
for Sivoia®QS shades
All shades fully open
All shades to 50%
All shades fully closed
Lower/Raise all shades
(Applies only to units with shade keypads)
The GRAFIK Eye®QS control unit controls most lighting loads without special
programming. Each unit ships with pre-programmed default settings for the scene and
shade buttons. For load types other than those shown below (dimmable or non-dim),
assign the load type before proceeding. See the scene setup section for instructions on
changing scene settings.

Zone Button Operation
Each zone column (LEDs and buttons)
represents one zone of lights. Pressing
any button on a column turns on the info
screen and displays the zone’s current
light level and current energy savings.
Pressing the raise and lower buttons on a
zone causes different actions depending
on zone type (see below).
Dimmable zones:
• Press and hold to raise/lower all lights in a
zone; release to stop
• Press raise or lower to stop a zone that is
fading
• Raising lights from off to full on or lowering
from full on to off takes 5 seconds
• Press raise and lower simultaneously to
toggle between full on and off
• Press and hold lower for 6 seconds after
the zone has gone to 0% light level to
set the zone as unaffected in the current
scene. The zone will not change when this
scene is initiated, and the Master buttons
will not raise/lower the zone in this scene.
Non-dim zones:
• Press raise to turn zone on
• Press lower to turn zone off
Note: To set zone types, see the zone
setup section.
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 13
Zone Raise
Zone Lower
Legend:
UA = Unaffected (lights are not affected by
scene button or Master buttons)
LED on
LED off
Zone LEDs
LEDs indicate
light level
(see below)
Zone LED Displays for % of Lighting Levels
Light Level
(%)
Off 1–17 18-33 34-49 50-66 67-82 83-99 On/
100
UA
Dimmable
Load Types
Non-Dim
Load Types

Entering and Exiting Programming Mode
Entering programming mode:
Press and hold the top and bottom scene
buttons simultaneously for 3 seconds. The
LEDs in the scene buttons will scroll from
top to bottom, confirming that you are in
programming mode, and the info screen will
display the main menu.
Exiting programming mode:
Press and hold the top and bottom scene
buttons simultaneously for 3 seconds. The
info screen will go to Scene 1.
Navigating Menus in Programming Mode
Master Buttons
The Master buttons allow you to move through the menu
choices. The current choice is highlighted on the info screen.
OK Button
The “OK” button chooses the current highlighted menu choice.
This will either take you to the next menu or accept a setting you
have selected. When the screen displays a Yes/No question, the
“OK” button is “Yes.”
Timeclock Button
The Timeclock button functions as a “back” button during
programming mode. Pressing the Timeclock button takes
you back one step in the current menu. Pressing it repeatedly
will eventually return you to the main menu, but will not exit
programming mode. When the screen displays a Yes/No
question, the Timeclock button is “No.”
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 14
Programming Mode
OK
Press and hold the top and
bottom buttons for 3 seconds
to enter or exit programming
mode
Master buttons
“OK” button
Timeclock (back) button
Main menu
Scene setup
Timeclock
Scene 1
Fade time
3 seconds

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 15
Wireless Mode
Many models of the GRAFIK Eye®QS control unit support wireless communication with
other Lutron®products. This feature allows for easy integration of wireless sensors,
keypads, remotes, and shades for single-room wireless applications, as well as
compatibility with other LutronRwireless systems such as RadioRA®2.
(See the RadioRA®2 Setup Guide; LutronRP/N 044254.)
Units supporting wireless communication are labeled “GRAFIK Eye®QS Wireless” on
the front label of the unit.
The wireless feature of the GRAFIK Eye®QS Wireless control unit has 3 modes of
operation.
• Ignore Programming (default): The GRAFIK Eye®QS Wireless control unit will only
respond to normal operation commands from wireless devices associated while in
“Enabled” mode.
• Disabled: Use for wired-only systems.
• Enabled (30 minutes): The GRAFIK Eye®QS Wireless control unit will respond to any
programming commands from nearby LutronRQS wireless (and compatible) products.
The GRAFIK Eye® will automatically revert to “Ignore Programming” mode if there is no
activity for 30 minutes.
Changing the wireless mode of the GRAFIK Eye®QS Wireless control unit:
1. Enter programming mode.
2. Use the Master buttons to highlight “Wireless Mode” and press
the “OK” button to accept.
3. Use the Master buttons to highlight the desired wireless mode,
and press the “OK” button to accept.
4. The info screen will display a confirming “Saved” message.
5. Exit programming mode.
Notes
• The wireless signal has a range of 30 ft (9 m) through standard
construction or 60 ft (18 m) line of sight.
• When used within a RadioRA®2 system, the wired QS link on the
GRAFIK Eye®QS control unit is disabled, and certain features
that do not pertain to RadioRA®2 are not accessible.
Wireless Mode
Enabled (30 minutes)
Saved
Saved
Main menu
Shade labels
Wireless Mode
FCC Information
Changes or modifications not expressly approved
by Lutron Electronics Co. could void the user’s
authority to operate this equipment.
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
rules. Operation is subject to the following: (1)
This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
These limits are designed to provide
reasonable protection against harmful interference
in a residential and commercial installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio or television
reception. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
OK
Master
buttons
“OK”
button
Timeclock
(back) button

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 16
Assigning Load Types
1. Enter programming mode.
2. Use the Master buttons to highlight
“Zone setup” and press the
“OK” button to accept.
3. Use the Master buttons to highlight
“Load type.” Press the “OK” button
to accept. See “Setting Load Types”
table on the next page.
4. Use the zone raise/lower buttons
to choose the load type for that
zone. See the list on the next page
for supported load types. Press the
“OK” button to accept.
5. The info screen will confirm that
your load type has been saved.
6. Exit programming mode.
Zone Setup
OK
Master
buttons
“OK” button
Main menu
CCI Setup
Zone setup
1 2 3 4 5 6 Use the
zone
raise/lower
buttons to
choose the
load type for
that zone.
Zone Setup
Non-Dim Load Type
Load Type
Set zones
Saved
Load Type
Assigning Non-Dim Load Types
Zones assigned to non-dim loads have five available configurations:
• LOFO: Last On, First Off
• FOFO: First On, First Off
• FOLO: First On, Last Off
• LOLO: Last On, Last Off
• 60/40: On at 60%, off at 40%
Scenes made up of both dim and non-dim
load types will toggle the non-dim loads before
the dim loads in a “First” on/off configuration,
and after the dim loads in a “Last” on/off
configuration.
1. Enter programming mode.
2. Use the Master buttons to highlight “Zone
setup” and press the “OK” button to accept.
3. Use the Master buttons to highlight “Non-Dim
Load type.” Press the “OK” button to accept.
See “Setting Load Types” table on the
next page.
4. Use the zone raise/lower buttons to choose
the non-dim load type for that zone. (Zones
not programmed as non-dim will be displayed
as Unaffected.) Press the “OK” button to
accept.
5. The info screen will confirm that your load type
has been saved.
6. Exit programming mode.
Main menu
CCI Setup
Zone setup
Zone Setup
Load Type
Load Type
Set zones
Saved
Non-Dim Load Type

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 17
Zone Setup (continued)
Load Type Notes
• All electronic low-voltage
(ELV) lighting used with an
interface must be rated for reverse
phase control dimming. Before
installing an ELV light source,
verify with the manufacturer that
their transformer can be dimmed.
When dimming, an ELV interface
(such as the PHPM-PA-DV-WH)
must be used with the control
unit.
• For all DMX or RGB/CMY DMX
lighting, an external DMX interface
(such as the QSE-CI-DMX) must
be used with the control unit.
• Maximum total lighting load for
Lutron®Tu-Wire®and Advance
Mark X®electronic dimming
ballasts (120 to 127 V~only)
must not exceed 6 A per zone
or 16 A per unit.
Zone ratings:
• Not all zones must be connected;
however, connected zones must
have a minimum load:
120 - 127 V~: 25 W
220 - 240 V~: 40 W
• Maximum zone loads:
120 - 127 V~: 800 W
220 - 240 V~: 1200 W
• Maximum total lighting load for
magnetic low-voltage (MLV) varies
by input voltage:
120 - 127 V~: 800 VA / 600 W
220 - 240 V~: 1200 VA / 960 W
LUTRON
LUTRON
Setting Load Types
Direct control via
GRAFIK Eye®QS
control unit
Control via
power module or
interface
Fixture load type Choose this load type from the menu
on the GRAFIK Eye®QS control unit:
Zones
1 – 6
Incandescent Incandescent Power module
MLV (magnetic low-voltage) MLV Power module
ELV (electronic low-voltage) — Power module
Hi-Lume®/Eco-10®— Fluorescent module
0-10 V — Fluorescent module
Non-dim lighting loads Non-dim Non-dim
Neon/Cold cathode Neon, CC Neon, CC
Tu-Wire®Tu-Wire Tu-Wire
Advance Mark X®Tu-Wire Tu-Wire
DMX — DMX
RGB/CMY DMX — RGB/CMY DMX
Cree LR4/LR6 LED Cree LR4/LR6 LED Fluorescent module
LED Incandescent* Power module
* Use incandescent load type unless otherwise specified in the LED product selection tool available at www.lutron.com/ledtool.
Power
module or
interface

Setting Minimum Level (optional)
Some local regulations specify a minimum lighting level for
dimming zones in occupied buildings. If this pertains to you,
follow these steps to set up your minimum lighting level.
1. Enter programming mode and select
“Zone setup,” then “Min level.” Press the
“OK” button to accept.
2. Use the Master buttons to highlight “Off”
if you want your lights to go all the way
off at their minimum light level, or “10%”
if you want that to be the minimum light
level. Press the “OK” button to accept.
Note: Non-dim loads will turn off
regardless of the minimum level
setting.
3. The info screen will confirm that your
minimum level has been saved.
4. Exit programming mode.
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 18
Zone Setup (continued)
Setting High End or Low End Trim
• If you are unsure about appropriate high and low end settings,
please contact LutronRTechnical Support for assistance.
• High and low end trim settings limit the maximum and minimum
output of a dimming zone. Trim levels are set automatically when
the load type is programmed.
1. Enter programming mode.
2. Use the Master buttons to highlight “Zone
setup” and press the “OK” button to
accept.
3. Use the Master buttons to highlight “High
end” or “Low end” (this example shows
low end). Press the “OK” button to accept.
4. Use the zone raise/lower buttons to set
the high end or low end trim for that
zone. The info screen will display each
zone number and percentage as you
adjust it. Press the “OK” button to accept.
5. The info screen will confirm that your
setting has been saved.
6. Exit programming mode.
Main menu
CCI Setup
Zone setup
High end
Zone 2
Low end
Set zones
Low end
OK
Master
buttons
1 2 3 4 5 6
Use the
zone
raise/lower
buttons to
set the high
end or low
end trim for
that zone.
“OK”
button
10%
Min level
Off
Zone setup
Low end
Min level
Zone setup
Saved Saved

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 19
Zone Setup (continued)
Labeling a Zone (optional)
1. Enter programming mode.
2. Use the Master buttons to highlight “Zone setup” and press
the “OK” button to accept.
3. Use the Master buttons to highlight “Label” and press the
“OK” button to accept.
4. Use the Master buttons to change the zone number to your
desired zone. Custom zone labels will appear if previously set.
Press the “OK” button to accept.
5. Use the Master buttons to highlight “Custom” and press the
“OK” button to accept. Or, highlight “Default” to return the
zone label to the default (e.g., Zone 1).
6. Use the Master buttons to scroll through the characters
(lowercase and uppercase letters, plus numbers 0 through 9).
The character you are currently changing will be underlined
on the screen. Press OK to select the character you want,
then repeat for all available characters. Choose a space (no
character) and press OK for any remaining characters. Press
the “OK” button to accept.
Note: Custom zone labels will always begin with the zone
number and a colon (e.g., 1: Uplights).
7. The info screen will confirm that your name has been saved.
8. Exit programming mode.
Main menu
CCI Setup
Zone setup
Min level
Label zone
Label
Label zone 2
Custom
Label zone 2
1: A
A
1 / 11
OK
Master
buttons
“OK”
button
Zone setup
Zone 2
Saved

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 20
Scene Setup
Setting Zone Levels, Fade Rates, and Shade Group Actions
1. Enter programming mode.
2. Use the Master buttons to highlight “Scene setup” and press
the “OK” button to accept.
3. Use the Master buttons to highlight “Levels” to adjust lighting
and/or shade levels. Press the “OK” button to accept. Use the
Master buttons to highlight the scene number of your desired
scene. Press the “OK” button to accept.
4. Set each zone to the desired light level for this scene using
the zone raise/lower buttons. The info screen will display the
zone and percentage as you adjust it.
To set a zone as unaffected, lower the light levels all the way
to off, then hold the zone lower button for 3 seconds. The
screen will display “---” and the three middle LEDs for the
zone will be lit to indicate this zone is unaffected by the scene
(the zone will not change when this scene is initiated).
When all zones are at the desired level, press the “OK” button
to accept.
5. Use the Master buttons to set the fade time for this scene.
Press the “OK” button to accept.
6. Note: This step is applicable only if you have shades on your
system. If you do not have or do not wish to set shade
groups for this scene, press the “OK” button to skip this
step.
Set each shade group to the desired level for this scene.
When all shade groups are at the desired level, press the
“OK” button to accept.
For shade programming, see the section on adjusting shade
settings.
7. The info screen will confirm that your scene has been saved.
8. Exit programming mode.
Main menu
Timeclock
Scene setup
Scene setup
Labels
Levels
Scene 1
Adjust fade
seconds
Scene 1
Set shade
Groups
3 seconds
Scene 1
Set zones
Scene setup
Scene 1
Saved
3
Shade
button group
Zone raise
Zone lower
OK
Master
buttons
“OK”
button
Timeclock
(back) button