Lutron Electronics GRAFIK Eye QSGRN-6PCE Operating instructions

LUTRON
Control Unit
Installation and Operation Guide
®
Please Read
The GRAFIK Eye®QS control unit allows
for control of both lights and window
treatments, without interfaces, using
a single control unit. Features include
pushbutton scene recall, info screen
that displays energy savings and status,
IR receiver, astronomic timeclock, contact
closure input, and engravable backlit
buttons that are easy to find and operate.
Model Numbers: QSGR-3PCE, QSGR-4PCE, QSGR-6PCE
QSGRK-3PCE, QSGRK-4PCE, QSGRK-6PCE
QSGRM-3PCE, QSGRM-4PCE, QSGRM-6PCE
QSGRN-6PCE, QSGRQ-6PCE
All units 230 V 50/60 Hz
QSGR-3PCE
QSGRK-3PCE
QSGRM-3PCE
QSGR-4PCE
QSGRK-4PCE
QSGRM-4PCE
QSGR-6PCE
QSGRK-6PCE
QSGRM-6PCE
QSGRN-6PCE
QSGRQ-6PCE
Unit Capacity (watts) 1 500 W 2 000 W 2 300 W
MLV 1 500 VA / 1 200 W 2 000 VA / 1 600 W 2 300 VA / 1 800 W
Zone Capacity (watts) 40 – 500 W 40 – 500 W 40 – 500 W
MLV 40 – 500 VA / 40 – 400 W 40 – 500 VA / 40 – 400 W 40 – 500 VA / 40 – 400 W
See page 8 for IEC PELV/NEC®Class 2 ratings.

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 2
Contents
Features and Functions of the
GRAFIK Eye®QS Control Unit .................3
Wiring the GRAFIK Eye®QS Control Unit
Overview of Line Voltage/Mains Wiring . . . . . . . . . 4
Line Voltage Wiring Details. . . . . . . . . . . . . . . . . . . 5
Overview of IEC PELV/NEC®Class 2 Wiring . . . . . 7
QS Link Control Wiring Details. . . . . . . . . . . . . . . . 8
Power Group Wiring Example . . . . . . . . . . . . . . . . 9
Powering More Than 3 Wallstations Example. . . 10
Completing Installation of the
GRAFIK Eye®QS Control Unit . . . . . . . . . . . . 11
General Functionality . . . . . . . . . . . . . . . . . . . 12
Pre-Programmed Button Functionality . . . . . 13
Zone Button Operation
Zone LED Displays for % of Lighting Levels. . . . 14
Programming Mode
Entering and Exiting Programming Mode . . . . . . 15
Navigating Menus in Programming Mode . . . . . . 15
WirelessMode.........................16
Zone Setup
Assigning Load Types. . . . . . . . . . . . . . . . . . . . . . 17
Assigning Non-Dim Load Type. . . . . . . . . . . . . . . 17
SettingLoadTypes........................18
Setting High End or Low End Trim. . . . . . . . . . . . 19
Setting Minimum Level (optional). . . . . . . . . . . . . 19
Labeling a Zone (optional) . . . . . . . . . . . . . . . . . . 20
Scene Setup
Setting Zone Levels, Fade Rates,
and Window Treatment Group Actions . . . . . . . 21
Labeling a Scene (optional) . . . . . . . . . . . . . . . . . 22
Enabling/Disabling Daylighting in a Scene . . . . . 22
Setting Save Mode
Save Mode Settings . . . . . . . . . . . . . . . . . . . . . . . 23
Quick Scene Programming:
SavebyOKMode........................23
Contact Closure Input (CCI) Setup
CCIModeSettings........................24
CCITypeSettings.........................25
Occupancy Sensor Setup . . . . . . . . . . . . . . . . 26
Associating Wireless Occupancy Sensors . . . . . 27
SelectingtheMode........................28
SceneMode .............................29
ZoneMode ..............................30
Labeling an Occupancy Sensor (optional). . . . . . 31
Configuring Occupancy Sensor Settings
(optional)...............................32
Daylight Sensor Setup . . . . . . . . . . . . . . . . . . 33
Associating Wireless Daylight Sensors . . . . . . . . 34
AssigningSensors.........................35
Labeling a Daylight Sensor (optional) . . . . . . . . . 36
Pico®Wireless Control Setup . . . . . . . . . . . . . 37
Associating with a GRAFIK Eye®QS
Wireless Control Unit . . . . . . . . . . . . . . . . . . . . . 38
Associating through a QS Sensor Module . . . . . 39
IRSetup..............................40
Enabling/Disabling the IR Receiver . . . . . . . . . . . 41
Associating the QS IR Eye with a
GRAFIK Eye®QS Control Unit . . . . . . . . . . . . . . 42
Associating through a QS Sensor Module . . . . . 44
Associating Sivoia®QS Window Treatments
and GRAFIK Eye®QS Control Units. . . . . . . 45
Adjusting Window Treatment Settings
SettingLimits.............................46
Preset Adjustment: Simple Method . . . . . . . . . . . 47
Preset Adjustment: Advanced Method . . . . . . . . 47
Naming a Group of Window Treatments . . . . . . . 48
Associating Multiple GRAFIK Eye®QS
ControlUnits..........................49
Timeclock Operation
Setting Time and Date . . . . . . . . . . . . . . . . . . . . . 50
SettingLocation ..........................51
Setting Daylight Saving Time . . . . . . . . . . . . . . . . 51
AddinganEvent ..........................52
DeletinganEvent .........................53
ViewinganEvent..........................53
SettingaHoliday..........................54
ViewingaHoliday.........................54
DeletingaHoliday.........................54
Copying a Schedule . . . . . . . . . . . . . . . . . . . . . . . 55
Deleting a Schedule . . . . . . . . . . . . . . . . . . . . . . . 55
Afterhours ............................56
Afterhours Examples. . . . . . . . . . . . . . . . . . . . . . . 57
Setting Up Afterhours . . . . . . . . . . . . . . . . . . . . . . 58
EndingAfterhours.........................58
Diagnostics and Special Settings
Enabling/Disabling the Timeclock . . . . . . . . . . . . 59
Enabling/Disabling the Backlighting . . . . . . . . . . 59
Diagnostics ..............................59
Setting the Security Password . . . . . . . . . . . . . . . 60
Language Selection . . . . . . . . . . . . . . . . . . . . 61
Faceplate Removal . . . . . . . . . . . . . . . . . . . . . 61
Troubleshooting .......................62
Troubleshooting: Wireless Functions. . . . . . . 63
Troubleshooting: Window Treatment
Functions.............................64
Warranty .............................65
Contact Information . . . . . . . . . . . . . . . . . . . . 65

OK
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 3
Info screen
Displays status or
programming functions
Scene buttons
With integral scene
indicator LEDs
Optional Shade
button groups
Preset and raise/lower
buttons with integral LEDs
(maximum of 3 button
groups)
Zone numbers
Zone raise/lower buttons
Zone LEDs display current
lighting zone levels
Timeclock button
Displays current
timeclock info
OK button
Used for programming
Infrared receiver
For handheld remote use
Master buttons
Temporarily raise and lower
lighting levels on unit
USB type mini B
For programming via PC
{
Hinged faceplate
Hinged faceplate
Features and Functions of the GRAFIK Eye®QS Control Unit

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 4
Wiring the GRAFIK Eye®QS Control Unit:
Overview of Line Voltage/Mains Wiring
1234
1 2 ABC
123456LN
4.0 mm2each
terminal
230 V
Distribution
Panel
Line Voltage/Mains
Cables and Load Wiring
123456LN
Incandescent load
Load controlled
by power module
or interface
Terminal labels:
L: Hot/Live
N: Neutral
: Ground
1-6: Dimmed/Switched
line voltage outputs
Power module
or interface

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 5
Wiring the GRAFIK Eye®QS Control Unit:
Line Voltage Wiring Details
• Useproperlycertifiedcableforallline
voltage/mains cables.
• Propershort-circuitandoverload
protection must be provided at the
distribution panel. You can use up to a
20 A circuit breaker for your installation.
• Installinaccordancewithalllocaland
national electrical codes.
• IECPELV/NEC®Class 2 terminals may
be temporarily unplugged for ease of IR,
occupancy sensor, and control wiring.
• Notice: Risk of damage to unit. Do not
connect line voltage/mains cable to IEC
PELV/NEC®Class 2 terminals.
Step 1: Install wallbox. Mount an
89mmdeep4-gangU.S.wallboxona
dry, flat indoor surface that is accessible
and allows for system programming
and operation. Allow at least 110 mm
clearance above and below the faceplate
to ensure proper heat dissipation. Allow
25 mm for faceplate overhang on all
sides.
Note:4-gangwallboxavailablefrom
Lutron;P/N241400.
Step 2: Test load wiring.
• TurnpowerOFFatthecircuitbreakeror
fuse box.
• Connectastandardlightswitchbetween
the live lead and load wire to test the
circuit.
• TurnpowerONandcheckforshortor
open circuits. If load does not operate,
the circuit is open. If the circuit breaker
trips (fuse blows or opens), a load short
may exist. Correct short or open circuits
and test again.
Step 3: Check control unit wiring.
•Earth/ground terminal connection must
be made as shown in line voltage wiring
diagrams.
•Do not mix different load types on the
same zone.
• Follow all local and national electrical
codeswheninstallingIECPELV/NEC®
Class 2 wiring with line voltage/mains
wiring.
WARNING! Shock hazard. May
result in serious injury or death.
Always turn off circuit breaker or
remove main fuse from power line
before doing any work. Before
connecting the loads to the
GRAFIK Eye®QS control unit, test
theloadsforshort-circuits.
Neutral
Hot/Live Switch
Load
LUTRON
LUTRON
Faceplate overhangs
wallbox on all sides;
allow 25 mm
110 mm

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 6
Wiring the GRAFIK Eye®QS Control Unit:
Line Voltage Wiring Details (continued)
Step 4: Connect line voltage and loads
to control unit.
• Strip8mmofinsulationofftheline
voltage/mains cables in the wallbox.
• Connectthelinevoltage/mains,ground,
and load wires to the appropriate
terminals on the back of the control unit.
L: Hot/Live
 N:Neutral
: Ground
 Terminals1-6:Dimmed/Switched
line voltage outputs
8 mm
The recommended installation torque
is0.6N∙m for line voltage/mains
connectionsand0.6N∙m for the earth/
ground connection.
Note: See the zone setup section for
a list of compatible load types and
instructions for programming the
GRAFIK Eye®QS control unit to properly
recognize them.
Notice: Risk of damage to unit. GRAFIK Eye®QS control units must be installed by a
qualified electrician in accordance with all applicable regulations and building codes.
Improper wiring can result in damage to control units or other equipment.
Note: To avoid overheating and possible damage to equipment, do not install control
unitstodimreceptacles,motor-operatedappliances,orfluorescentlightingnot
equippedwithLutronHi-lume®,Eco-10®,Tu-Wire®, electronic dimming ballasts, or
otherdevicesapprovedforyourlocation.Indimmedmagneticlow-voltagecircuits,
youcanpreventtransformeroverheatingandfailurebyavoidingexcessivelyhighcur-
rent flow. Do not operate control units with any lamps removed or burned out; replace
any burned out lamps immediately; use only transformers that incorporate thermal
protection or fused primary windings. Control units are designed for residential and
commercial use, for indoor use only.

1234
1 2 ABC
123456LN
Contact Closure Input Wiring
24 V 50 mA
For settings, see CCI Mode Setup.
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 7
1 2 ABC
NH123456
1234
1234
1 2
ABC
123456LN
1234
1 2
ABC
123456LN
Note: Use appropriate wire
connecting devices as
specified by local codes.
Example:
Occupancy sensor
(maximum 1)
1: COM
2: 24 V *
3: MUX
4: MUX
QS Link Control Wiring
24 V 100 mA
Wiring the GRAFIK Eye®QS Control Unit:
Overview of IEC PELV/NEC®Class 2 Wiring
IR Wiring
From external
IR connection
(by others)
1.0 mm2each
terminal
1.0 mm2each terminal
1: IR DATA
2: IR COM
A: CCI SIG
B: 24 V
C: CCI COM
To control
stations, window
treatments, or
other GRAFIK Eye®
QS control units
Data (terminals 3 and 4):
Twisted, shielded pair 0.5 mm2
each terminal
Common and power (terminals 1 and 2):
Two 1.0 mm2each terminal (for link <153 m)
Two 4.0 mm2eachterminal(forlink153-610m)
*Do not connect terminal 2
between any GRAFIK Eye®
QS control unit and any other
power supply, including another
GRAFIK Eye®QS control unit.
See “Power Group Wiring” for a
detailed wiring example.
1234
1 2
ABC
123456LN
Example:
Emergency lighting interface (maximum 1)
Note: The GRAFIK Eye®QS control unit
mustbepoweredbyaNormal/
Emergency distribution panel for
proper ELI operation. Refer to the
LUT-ELI-3PHInstallationGuidefor
the complete wiring diagram.
A: CCI SIG
B: 24 V
C: CCI COM
LUT-ELI-3PH
Signal
+V Input
Circuit Common

• SystemcommunicationusesIECPELV/NEC®
Class 2 wiring.
• Followalllocalandnationalelectricalcodeswhen
installingIECPELV/NEC®Class 2 wiring with line
voltage/mains wiring.
• Eachterminalacceptsuptotwo1.0mm2wires.
• Totallengthofcontrollinkmustnotexceed610m.
• Makeallconnectionsinthecontrolunit’swallbox.
• WiringcanbeT-tappedordaisy-chained.
• IECPELV/NEC®Class 2 24 V 150 mA.
System Limits
The QS wired communication link is limited to 100
devices or 100 zones.
The GRAFIK Eye®QS control unit supplies 3 Power
Draw Units (PDUs) on the QS link. Refer to the
QS Link Power Draw Units specification submittal
(LutronPN369405)formoreinformationconcerning
Power Draw Units.
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 8
Wiring the GRAFIK Eye® QS Control Unit:
QS Link Control Wiring Details
QS smart
power
panel
LUTRON
LUTRON
LUTRON
LUTRONLUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
T-Tap Wiring Example
GRAFIK Eye®QS
control unit
Sivoia®QS
window
treatment
seeTouch®QS
wallstation
LUTRON
LUTRON
LUTRON
LUTRONLUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON LUTRON LUTRON
LUTRON
GRAFIK Eye®QS
control unit
Sivoia®
QS
window
treatment
seeTouch®QS
wallstations
Daisy-Chain Wiring Example
QS smart
power panel
GRAFIK Eye®QS
control unit
Wire Sizes (check compatibility in your area)
QS Link Wiring Length Wire Gauge Lutron Cable Part Number
Less than 153 m Power (terminals 1 and 2)
1 pair 1.0 mm2GRX-CBL-346S
GRX-PCBL-346S
Data (terminals 3 and 4)
1 twisted, shielded pair 0.5 mm2
153 to 610 m Power (terminals 1 and 2)
1 pair 4.0 mm2GRX-CBL-46L
GRX-PCBL-46L
Data (terminals 3 and 4)
1 twisted, shielded pair 0.5 mm2

Wiring the GRAFIK Eye®QS Control Unit:
Power Group Wiring Example
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 9
LUTRON
On the QS link, there are devices that supply power and devices that consume power. Each device has a specic number of Power
Draw Units (PDUs) it either supplies or consumes. A Power Group consists of one device that supplies power and one or more
devicesthatconsumepower;eachPowerGroupmayhaveonlyonepower-supplyingdevice.Refer to the QS Link Power Draw Units
specificationsubmittal(LutronPN369405)formoreinformationconcerningPDUs.
Within Power Groups on the QS link, connect all 4 terminals (1, 2, 3, and 4), shown by the letter A in the diagram. Between devices on
theQSlinkthatsupplypower,connectonlyterminals1,3,and4(NOTterminal2),shownbytheletterBonthediagram.
WiringcanbeT-tappedordaisy-chained.
Power Group 1
Power Group 2
Power Group 3
A
A
A
B
B
(Do not connect
terminal 2: 24 V )
(Do not connect
terminal 2: 24 V )
GRAFIK Eye®QS
control unit
Supplies PDUs
QS Power Supply
Supplies PDUs
Energi Savr NodeTM
unit Supplies PDUs
Control Interfaces
Consume PDUs
Control Interfaces
Consume PDUs
Wallstations
Consume PDUs
Wallstations
Consume PDUs
Wallstations
Consume PDUs
QS Sensor Module with
Occupancy Sensor
Consumes PDUs
Quantum®panel
Supplies PDUs
Connect all 4 terminals within a
power group:
1: Common
2: 24 V
3 and 4: Data
Connect only 3 terminals
between power groups:
1: Common
3 and 4: Data
Do not connect
Terminal 2: 24 V
A
B

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 10
4 3 2 1
C B A
4 3 2 1
C B A
4 3 2 1
C B A
4 3 2 1
C B A
1234
1 2 ABC
123456HN
Wiring the GRAFIK Eye®QS Control Unit:
Powering More Than 3 Wallstations Example
• The +24 VDC wire from the power supply
connects to QS link terminal 2 on all of
the wallstations it is powering. This wire
does not connect to terminal 2 on the
GRAFIK Eye®QS control unit.
The GRAFIK Eye®QS control unit can power up to 3 seeTouch®wallstations. An external 24 V power supply is required to power
more than three wallstations.
To power source
QSPS-P1-1-50
(powers up to 8 seeTouch®QS
wallstations)
• The Common wire from the power
supply connects to QS link terminal 1
on all of the wallstations it is powering
and terminal 1 on the GRAFIK Eye®QS
control unit.
GRAFIK Eye®QS control unit
(rear view)
1 twisted pair
0.5 mm2
Lutron cable
GRX-CBL-346S-500 or
GRX-PCBL-346S-500
seeTouch®QS wallstations
(1) 1.0 mm2
Common
• The communication signals on the QS
link (terminals 3 and 4) connect from
the wallstations to the GRAFIK Eye®QS
control unit on twisted, shielded cable
just as when an additional power supply
is not being used. Control unit shown in
rear view.

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 11
Completing Installation of the GRAFIK Eye®QS Control Unit
1.Mount the control unit in the wallbox as
shown using the four screws provided.
Note: Follow all local and national
electrical codes when installing IEC
PELV/NEC®Class 2 wiring with line
voltage/mains wiring.
2.Verify installation:
•Restore power.
•Press the top scene button. The LED will
light.
•Press the zone raise and lower buttons.
Make sure the control unit is dimming all
connected loads.
3.Apply the protective overlay to the control
unit.
Note: When tightening mounting
screws, make sure that the hinged
cover and faceplate will open fully,
as shown.
Wall
200 mm
87 mm
95 mm
Protective overlay
(apply after installation)

OK
1 2 3 4 5 6
The info screen turns off 30 seconds after the last button press
or completion of the last scene change. See example screens below.
The Master buttons activate the info screen. These buttons
temporarily raise or lower all dimmable lights (except those
programmed as unaffected in the current scene). Adjustments are
temporary and do not affect scene programming.
Note: Master buttons affect all zones.
The OK button activates the info screen (when off), which then
shows the current scene and its fade time. In Save Always mode,
it allows fade time adjustment. In Save by OK mode, pressing
a second time allows zone adjustment; pressing a third time
allows fade adjustment.
The timeclock button activates the info screen and displays the
current time and the next event scheduled to occur. Pressing
a second time displays the time, date, and afterhours status.
Pressing a third time displays location and sunrise/sunset times.
Pressing a fourth time displays the language selection screen.
Pressing once more returns to the first screen.
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 12
Scene 1
Master raise
Master lower
General Functionality
OK
1 2 34569 10 11 12 13 14 7815 16
9-16
1-8
OK
1 2 34569 10 11 12 13 14 7815 16
9-16
1-8
OK
1 2 34569 10 11 12 13 14 7815 16
9-16
1-8
Scene 1
Adjust fade
3seconds
11:23 AM Fri
Next: 5:00 PM
Scene 1
Master buttons
OK button
Timeclock
(back) button

Pre-Programmed Button Functionality
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 13
OK
1 2 34569 10 11 12 13 14 7815 16
9-16
1-8
Scene Button Pre-Programming
for Dimmable Loads
Scene 1: All zones to 100%
Scene 2: All zones to 75%
Scene 3: All zones to 50%
Scene 4: All zones to 25%
All zones Off
OK
1 2 34569 10 11 12 13 14 7815 16
9-16
1-8
Shade Button Pre-Programming
for Sivoia®QS window treatments
All window treatments fully open
All window treatments to 50%
All window treatments fully closed
Lower/Raise all window treatments
(Applies only to units with shade keypads)
The GRAFIK Eye®QS control unit controls most lighting loads without special
programming.Eachunitshipswithpre-programmeddefaultsettingsforthesceneand
shadebuttons.Forloadtypesotherthanthoseshownbelow(dimmableornon-dim),
assign the load type before proceeding. See the scene setup section for instructions on
changing scene settings.

Zone Button Operation
Each zone column (LEDs and buttons)
represents one zone of lights. Pressing
any button on a column turns on the info
screenanddisplaysthezone’scurrent
light level and current energy savings.
Pressing the raise and lower buttons on a
zone causes different actions depending
on zone type (see below).
Dimmable zones:
• Pressandholdtoraise/loweralllightsina
zone; release to stop
• Pressraiseorlowertostopazonethatis
fading
• Raisinglightsfromofftofullonorlowering
from full on to off takes 5 seconds
• Pressraiseandlowersimultaneouslyto
toggle between full on and off
• Pressandholdlowerfor6secondsafter
the zone has gone to 0% light level to
set the zone as unaffected in the current
scene. The zone will not change when this
scene is initiated, and the Master buttons
will not raise/lower the zone in this scene.
Non-dim zones:
• Pressraisetoturnzoneon
• Presslowertoturnzoneoff
Note: To set zone types, see the zone
setup section.
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 14
OK
OK
Zone Raise
Zone Lower
Legend:
UA = Unaffected (lights are not affected by
scene button or Master buttons)
LED lit
LED off
Zone LEDs
LEDs indicate
light level
(see below)
Zone LED Displays for % of Lighting Levels
Light Level
(%)
Off 1–17 18-33 34-49 50-66 67-82 83-99 On/
100
UA
Dimmable
Load Types
Non-Dim
Load Types

Entering and Exiting Programming Mode
Entering programming mode:
Press and hold the top and bottom scene
buttons simultaneously for 3 seconds. The
LEDs in the scene buttons will scroll from
top to bottom, confirming that you are in
programming mode, and the info screen will
display the main menu.
Exiting programming mode:
Press and hold the top and bottom scene
buttons simultaneously for 3 seconds. The
info screen will go to Scene 1.
Navigating Menus in Programming Mode
Master Buttons
The Master buttons allow you to move through the menu
choices. The current choice is highlighted on the info screen.
OK Button
The OK button chooses the current highlighted menu choice.
This will either take you to the next menu or accept a setting you
haveselected.WhenthescreendisplaysaYes/Noquestion,the
OK button is “Yes”.
Timeclock Button
The timeclock button functions as a “back” button during
programming mode. Pressing the timeclock button takes you
back one step in the current menu. Pressing it repeatedly
will eventually return you to the main menu, but will not exit
programmingmode.WhenthescreendisplaysaYes/No
question,theTimeclockbuttonis“No”.
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 15
Programming Mode
OK
1 2 3 4 5 6
Press and hold the top and
bottom buttons for 3 seconds
to enter or exit programming
mode
Master buttons
OK button
Timeclock (back) button
Main menu
Scene setup
Timeclock
Scene 1
Fade time
3 seconds

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 16
Wireless Mode
Many models of the GRAFIK Eye®QS control unit support wireless communication with
other Lutron®products. This feature allows for easy integration of wireless sensors,
keypads,remotes,andwindowtreatmentsforsingle-roomwirelessapplications.
Units supporting wireless communication are labeled “GRAFIK Eye®QS Wireless” on
the front label of the unit.
The wireless feature of the GRAFIK Eye®QS Wireless control unit has three (3) modes
of operation.
• Disabled:Useforwired-onlysystems.
• Enabled: The GRAFIK Eye®QS Wireless control unit will respond to any programming
commands from nearby Lutron QS wireless (and compatible) products.
• Ignore Programming (default): The GRAFIK Eye®QS Wireless control unit will only
respond to normal operation commands from wireless devices associated while in
Enabled mode.
Changing the wireless mode of the GRAFIK Eye®QS Wireless control unit:
1. Enter programming mode.
2. Use the Master buttons to highlight “Wireless Mode” and press
the OK button to accept.
3. Use the Master buttons to highlight the desired wireless mode,
and press the OK button to accept.
4. The info screen will display a confirming “Saved” message.
5. Exit programming mode.
Note: The wireless signal has a range of 9 m through standard
construction or 18 m line of sight.
Wireless Mode
Enabled
Saved
Saved
Main menu
Shade labels
Wireless Mode
OK
Master
buttons
OK
button
Timeclock
(back) button

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 17
Assigning Load Types
1. Enter programming mode.
2. Use the Master buttons to highlight
“Zone setup” and press the
OK button to accept.
3. Use the Master buttons to highlight
“Load type”. Press the OK button to
accept. See “Setting Load Types”
table on the next page.
4. Use the zone raise/lower buttons to
choose the load type for that zone.
See the list on the next page for
supported load types. Press the OK
button to accept.
5. The info screen will confirm that
your load type has been saved.
6. Exit programming mode.
Zone Setup
OK
1 2 3 4 5 6
Master
buttons
OK button
Main menu
CCI Setup
Zone setup
OK
1 2 3 4 5 6
Use the
zone
raise/lower
buttons to
choose the
load type for
that zone.
Zone Setup
Non-Dim Load Type
Load Type
Set zones
Saved
Load Type
Assigning Non-Dim Load Type
Zonesassignedtonon-dimloadshavethreeavailableconfigurations:
•LOFO: Last On, First Off
•FOFO: First On, First Off
•FOLO: First On, Last Off
Scenesmadeupofbothdimandnon-dim
loadtypeswilltogglethenon-dimloads
before the dim loads in a “First” on/off
configuration, and after the dim loads in a
“Last” on/off configuration.
1. Enter programming mode.
2. Use the Master buttons to highlight “Zone
setup” and press the OK button to accept.
3.UsetheMasterbuttonstohighlight“Non-Dim
Load type”. Press the OK button to accept.
See “Setting Load Types” table on the next
page.
4. Use the zone raise/lower buttons to choose
thenon-dimloadtypeforthatzone.(Zones
notprogrammedasnon-dimwillbedisplayed
as Unaffected.) Press the OK button to
accept.
5. The info screen will confirm that your load
type has been saved.
6. Exit programming mode.
Main menu
CCI Setup
Zone setup
Zone Setup
Load Type
Load Type
Set zones
Saved
Non-Dim Load Type

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 18
Zone Setup (continued)
Load Type Notes
• Allelectroniclow-voltage
(ELV) lighting used with an
interface must be rated for reverse
phase control dimming. Before
installing an ELV light source,
verify with the manufacturer that
their transformer can be dimmed.
When dimming, an ELV interface
(suchasthePHPM-PA-DV-WH)
must be used with the control
unit.
• ForallDMXorRGB/CMYDMX
lighting,anexternalDMXinterface
(suchastheQSE-CI-DMX)must
be used with the control unit.
Zone ratings:
•Notallzonesmustbeconnected;
however, connected zones must
have a minimum load of 40 W.
•Maximumloads:
10 A per unit
500 W per zone.
•Maximumtotallightingloadfora
magneticlow-voltage(MLV)load
is 500 VA / 400 W.
LUTRON
LUTRON
LUTRON
LUTRON
Setting Load Types
Direct control via
GRAFIK Eye®QS
control unit
Control via
power module or
interface
Fixture load type Choose this load type from the menu
on the GRAFIK Eye®QS control unit:
Zones
1 – 6
Incandescent Incandescent Power module
MLV (magnetic low-voltage) MLV Power module
ELV (electronic low-voltage) — Power module
Hi-lume®/Eco-10®— Fluorescent module
0-10 V — Fluorescent module
Non-dim lighting loads Non-dim Non-dim
Neon/Cold cathode Neon, CC Neon, CC
DMX — DMX
RGB/CMY DMX — RGB/CMY DMX
Power
module or
interface

Setting Minimum Level (optional)
Some local regulations specify a minimum lighting level for
dimming zones in occupied buildings. If this pertains to you,
follow these steps to set up your minimum lighting level.
1. Enter programming mode and select
“Zone setup,” then “Min level”. Press the
OK button to accept.
2. Use the Master buttons to highlight
“OFF” if you want your lights to go all
the way off at their minimum light level,
or “10%” if you want that to be the
minimum light level. Press the OK button
to accept.
Note:Non-dimloadswill turn off
regardless of the minimum level setting.
3. The info screen will confirm that your
minimum level has been saved.
4. Exit programming mode.
®GRAFIK Eye®QS Control Unit Installation and Operation Guide 19
Zone Setup
Setting High End or Low End Trim
•If you are unsure about appropriate high and low end settings,
please contact Lutron Technical Support for assistance.
•High and low end trim settings limit the maximum and minimum
output of a dimming zone. Trim levels are set automatically when
the load type is programmed.
1. Enter programming mode.
2. Use the Master buttons to highlight
“Zone setup” and press the OK button to
accept.
3. Use the Master buttons to highlight “High
end” or “Low end” (this example shows
low end). Press the OK button to accept.
4. Use the zone raise/lower buttons to set
the high end or low end trim for that
zone. The info screen will display each
zone number and percentage as you
adjust it. Press the OK button to accept.
5. The info screen will confirm that your
setting has been saved.
6. Exit programming mode.
Main menu
CCI Setup
Zone setup
High end
Zone 2
Low end
Set zones
Low end
OK
1 2 3 4 5 6
Master
buttons
OK
1 2 3 4 5 6
Use the
zone
raise/lower
buttons to
set the high
end or low
end trim for
that zone.
OK
button
10%
Min level
Off
Zone setup
Low end
Min level
Zone setup
Saved Saved

®GRAFIK Eye®QS Control Unit Installation and Operation Guide 20
Zone Setup
Labeling a Zone (optional)
1. Enter programming mode.
2. Use the Master buttons to highlight “Zone setup” and press
the OK button to accept.
3. Use the Master buttons to highlight “Label” and press the
OK button to accept.
4. Use the Master buttons to change the zone number to your
desired zone. Custom zone labels will appear if previously set.
Press the OK button to accept.
5. Use the Master buttons to highlight “Custom” and press the
OK button to accept. Or, highlight “Default” to return the zone
label to the default (e.g., Zone 1).
6. Use the Master buttons to scroll through the characters
(lowercase and uppercase letters, plus numbers 0 through 9).
The character you are currently changing will be underlined
on the screen. Press OK to select the character you want,
then repeat for all available characters. Choose a space (no
character) and press OK for any remaining characters. Press
the OK button to accept.
Note: Custom zone labels will always begin with the zone
number and a colon (e.g., 1: Uplights).
7. The info screen will confirm that your name has been saved.
8. Exit programming mode.
Main menu
CCI Setup
Zone setup
Min level
Label zone
Label
Label zone 2
Custom
Label zone 2
1: A
A
1 / 11
OK
1 2 3 4 5 6
Master
buttons
OK
button
Zone setup
Zone 2
Saved