Lutron Electronics QSGRK-3PCE Owner's manual

LUTRON
Control Unit
Quick Installation
and Operation Guide
English 中文
Español Italiano
Français Deutsch
®
Please Read
The GRAFIK Eye®QS control unit allows for control of both lights and window
treatments, without interfaces, using a single control unit. Features include
pushbutton scene recall, info screen that displays energy savings and status,
IR receiver, astronomic timeclock, contact closure input, and engravable backlit
buttons that are easy to find and operate.
Contents
Features and Functions of the
GRAFIK Eye®QS Control Unit .................2
Wiring the GRAFIK Eye®QS Control Unit
Overview of Line Voltage/Mains Wiring. . . . . . . . . 3
Line Voltage Wiring Details. . . . . . . . . . . . . . . . . . . 4
Overview of IEC PELV Wiring. . . . . . . . . . . . . . . . . 6
QS Link Control Wiring Details. . . . . . . . . . . . . . . . 7
Power Group Wiring Example . . . . . . . . . . . . . . . . 8
Completing Installation of the
GRAFIK Eye®QS Control Unit . . . . . . . . . . . . . 9
Programming Mode
Entering and Exiting Programming Mode . . . . . . 10
Navigating Menus in Programming Mode . . . . . . 10
WirelessMode.........................11
Zone Setup
Assigning Load Types. . . . . . . . . . . . . . . . . . . . . . 12
Assigning Non-Dim Load Type. . . . . . . . . . . . . . . 12
SettingLoadTypes........................13
Scene Setup
Setting Zone Levels, Fade Rates,
and Window Treatment Group Actions . . . . . . . 14
Occupancy Sensor Setup . . . . . . . . . . . . . . . . 15
SceneMode .............................16
Configuring Occupancy Sensor Settings
(optional)...............................17
Pico®Wireless Control Setup:
Associating with a GRAFIK Eye®QS
Wireless Control Unit . . . . . . . . . . . . . . . . . . . . . 18
Troubleshooting .......................19
Warranty .............................20
Contact Information . . . . . . . . . . . . . . . . . . . . 20
For additional features and advanced functions,
see the complete installation and operation guide at
www.lutron.com/qs
Model Numbers: QSGRK-3PCE, QSGRK-4PCE, QSGRK-6PCE
QSGRM-3PCE, QSGRM-4PCE, QSGRM-6PCE
QSGR-3PCE, QSGR-4PCE, QSGR-6PCE
All units 230 V 50/60 Hz
QSGRK-3PCE
QSGRM-3PCE
QSGR-3PCE
QSGRK-4PCE
QSGRM-4PCE
QSGR-4PCE
QSGRK-6PCE
QSGRM-6PCE
QSGR-6PCE
Unit Capacity
(watts)
1 500 W 2 000 W 2 300 W
MLV 1 500 VA
1 200 W
2 000 VA
1 600 W
2 300 VA
1 800 W
Zone Capacity
(watts)
40 – 500 W 40 – 500 W 40 – 500 W
MLV 40 – 500 VA
40 – 400 W
40 – 500 VA
40 – 400 W
40 – 500 VA
40 – 400 W
See page 6 for IEC PELV ratings.

OK
®
Info screen
Displays status or
programming functions
Scene buttons
With integral scene
indicator LEDs
Optional Shade
button groups
Preset and raise/lower
buttons with integral LEDs
(maximum of 3 button
groups)
Zone numbers
Zone raise/lower buttons
Zone LEDs display current
lighting zone levels
Timeclock button
Displays current
timeclock info
OK button
Used for programming
Infrared receiver
For handheld remote use
Master buttons
Temporarily raise and lower
lighting levels on unit
USB type mini B
For programming via PC
{
Hinged faceplate
Hinged faceplate
Features and Functions of the GRAFIK Eye®QS Control Unit
For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 2

®
For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 3
Wiring the GRAFIK Eye®QS Control Unit:
Overview of Line Voltage/Mains Wiring
1234
1 2 ABC
123456LN
4.0 mm2each
terminal
230 V
Distribution
Panel
Line Voltage/Mains
Cables and Load Wiring
123456LN
Incandescent load
Load controlled
by power module
or interface
Terminal labels:
L: Hot/Live
N: Neutral
: Ground
1-6: Dimmed/Switched
line voltage outputs
Power module or
interface

®
Wiring the GRAFIK Eye®QS Control Unit:
Line Voltage Wiring Details
• Useproperlycertifiedcableforallline
voltage/mains cables.
• Propershort-circuitandoverload
protection must be provided at the
distribution panel. You can use up to a
20 A circuit breaker for your installation.
• Installinaccordancewithalllocaland
national electrical codes.
• IECPELVterminalsmaybetemporarily
unplugged for ease of IR, occupancy
sensor, and control wiring.
• Notice: Risk of damage to unit. Do not
connect line voltage/mains cable to IEC
PELV terminals.
Step 1: Install wallbox. Mount an
89mmdeep4-gangU.S.wallboxona
dry, flat indoor surface that is accessible
and allows for system programming
and operation. Allow at least 110 mm
clearance above and below the faceplate
to ensure proper heat dissipation. Allow
25 mm for faceplate overhang on all
sides.
Note:4-gangwallboxavailablefrom
Lutron; P/N 241400.
Step 2: Test load wiring.
• TurnpowerOFFatthecircuitbreakeror
fuse box.
• Connectastandardlightswitchbetween
the live lead and load wire to test the
circuit.
• TurnpowerONandcheckforshortor
open circuits. If load does not operate,
the circuit is open. If the circuit breaker
trips (fuse blows or opens), a load short
may exist. Correct short or open circuits
and test again.
Step 3: Check control unit wiring.
•Earth/ground terminal connection must
be made as shown in line voltage wiring
diagrams.
•Do not mix different load types on the
same zone.
• Follow all local and national electrical
codes when installing IEC PELV wiring
with line voltage/mains wiring.
WARNING! Shock hazard. May
result in serious injury or death.
Always turn off circuit breaker or
remove main fuse from power line
before doing any work. Before
connecting the loads to the
GRAFIK Eye®QS control unit, test
theloadsforshort-circuits.
Neutral
Hot/Live Switch
Load
LUTRON
LUTRON
Faceplate overhangs
wallbox on all sides;
allow 25 mm
110 mm
For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 4

®
For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 5
Wiring the GRAFIK Eye®QS Control Unit:
Line Voltage Wiring Details (continued)
Step 4: Connect line voltage and loads
to control unit.
• Strip8mmofinsulationofftheline
voltage/mains cables in the wallbox.
• Connectthelinevoltage/mains,ground,
and load wires to the appropriate
terminals on the back of the control unit.
L: Hot/Live
N: Neutral
: Ground
 Terminals1-6:Dimmed/Switched
line voltage outputs
8 mm
The recommended installation torque
is0.6N∙m for line voltage/mains
connectionsand0.6N∙m for the earth/
ground connection.
Note: See the zone setup section for
a list of compatible load types and
instructions for programming the
GRAFIK Eye®QS control unit to properly
recognize them.
Notice: Risk of damage to unit. GRAFIK Eye®QS control units must be installed by
a qualified electrician in accordance with all applicable regulations and building codes.
Improper wiring can result in damage to control units or other equipment.
Note: To avoid overheating and possible damage to equipment, do not install control
unitstodimreceptacles,motor-operatedappliances,orfluorescentlightingnot
equippedwithLutronHi-lume®,Eco-10®,Tu-Wire®, electronic dimming ballasts, or
otherdevicesapprovedforyourlocation.Indimmedmagneticlow-voltagecircuits,
youcanpreventtransformeroverheatingandfailurebyavoidingexcessivelyhighcur-
rent flow. Do not operate control units with any lamps removed or burned out; replace
any burned out lamps immediately; use only transformers that incorporate thermal
protection or fused primary windings. Control units are designed for residential and
commercial use, for indoor use only.

1234
1 2 ABC
123456LN
Contact Closure Input Wiring
24 V 50 mA
For settings, see the full installation
and operation guide at
www.lutron.com/qs
®
1 2 ABC
NH123456
1234
1234
1 2
ABC
123456LN
1234
1 2
ABC
123456LN
Note: Use appropriate wire connecting
devices as specified by local
codes.
Example:
Occupancy sensor
(maximum 1)
1: COM
2: 24 V *
3: MUX
4: MUX
QS Link Control Wiring
Wiring the GRAFIK Eye®QS Control Unit:
Overview of IEC PELV Wiring
IR Wiring
From external
IR connection
(by others)
1.0 mm2each
terminal
1.0 mm2each terminal
1: IR DATA
2: IR COM
A: CCI SIG
B: 24 V
C: CCI COM
To control
stations, window
treatments, or
other GRAFIK Eye®
QS control units
Data (terminals 3 and 4):
Twisted, shielded pair 0.5 mm2each terminal
24 V 100 mA
Common and power (terminals 1 and 2):
Two 1.0 mm2each terminal (for link <153 m)
Two 4.0 mm2eachterminal(forlink153-610m)
*Do not connect terminal 2
between any GRAFIK Eye®QS
control unit and any other power
supply, including another GRAFIK
Eye®QS control unit.
See “Power Group Wiring” for a
detailed wiring example.
1234
1 2
ABC
123456LN
Example:
Emergency lighting interface (maximum 1)
Note: The GRAFIK Eye®QS control unit
must be powered by a Normal/
Emergency distribution panel for
proper ELI operation. Refer to the
LUT-ELI-3PHInstallationGuidefor
the complete wiring diagram.
A: CCI SIG
B: 24 V
C: CCI COM
LUT-ELI-3PH
Signal
+V Input
Circuit Common
For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye®QSControlUnitQuickInstallationandOperationGuide6

• SystemcommunicationusesIECPELVwiring.
• Followalllocalandnationalelectricalcodeswhen
installing IEC PELV wiring with line voltage/mains
wiring.
• Eachterminalacceptsuptotwo1.0mm2wires.
• Totallengthofcontrollinkmustnotexceed
610m.
• Makeallconnectionsinthecontrolunit’swallbox.
• WiringcanbeT-tappedordaisy-chained.
• IECPELV24V 150 mA.
System Limits
The QS wired communication link is limited to 100
devices or 100 zones.
The GRAFIK Eye®QS control unit supplies 3 Power
Draw Units (PDUs) on the QS link. Refer to the
QS Link Power Draw Units specification submittal
(LutronPN369405)formoreinformationconcerning
Power Draw Units.
®
Wiring the GRAFIK Eye® QS Control Unit:
QS Link Control Wiring Details
QS smart
power
panel
LUTRON LUTRON LUTRON
LUTRON
LUTRON
LUTRON
T-Tap Wiring Example
GRAFIK Eye®QS
control unit
Sivoia®QS
window
treatment
seeTouch®QS
wallstation
LUTRON LUTRON LUTRON
LUTRON
LUTRON
LUTRON
GRAFIK Eye®QS
control unit
Sivoia®
QS
window
treatment seeTouch®QS
wallstations
Daisy-Chain Wiring Example
QS smart
power panel
GRAFIK Eye®QS
control unit
For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 7
Wire Sizes (check compatibility in your area)
QS Link Wiring Length Wire Gauge Lutron Cable Part Number
Less than 153 m Power (terminals 1 and 2)
1 pair 1.0 mm2GRX-CBL-346S (non-plenum)
GRX-PCBL-346S (plenum)
Data (terminals 3 and 4)
1 twisted, shielded pair 0.5 mm2
153 to 610 m Power (terminals 1 and 2)
1 pair 4.0 mm2GRX-CBL-46L (non-plenum)
GRX-PCBL-46L (plenum)
Data (terminals 3 and 4)
1 twisted, shielded pair 0.5 mm2

Wiring the GRAFIK Eye®QS Control Unit: Power Group Wiring Example
®
On the QS link, there are devices that supply power and devices that consume power. Each device has a specic number of Power
Draw Units (PDUs) it either supplies or consumes. A Power Group consists of one device that supplies power and one or more
devicesthatconsumepower;eachPowerGroupmayhaveonlyonepower-supplyingdevice.Refer to the QS Link Power Draw Units
specificationsubmittal(LutronPN369405)formoreinformationconcerningPDUs.
Within Power Groups on the QS link, connect all 4 terminals (1, 2, 3, and 4), shown by the letter A in the diagram. Between devices on
the QS link that supply power, connect only terminals 1, 3, and 4 (NOT terminal 2), shown by the letter B on the diagram.
WiringcanbeT-tappedordaisy-chained.
For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 8
LUTRON
Power Group 1
Power Group 2
Power Group 3
A
A
A
B
B
B
(Do not connect
terminal 2: 24 V )
(Do not connect
terminal 2: 24 V )
GRAFIK Eye®QS
control unit
Supplies PDUs
QS Power Supply
Supplies PDUs
Energi Savr NodeTM
unit Supplies PDUs
Control Interfaces
Consume PDUs
Control Interfaces
Consume PDUs
Wallstations
Consume PDUs
Wallstations
Consume PDUs
Wallstations
Consume PDUs
QS Sensor Module with
Occupancy Sensor
Consumes PDUs
Connect all 4 terminals
within a power group:
1: Common
2: 24 V
3 and 4: Data
Connect only 3 terminals
between power groups:
1: Common
3 and 4: Data
Do not connect
Terminal 2: 24 V
A
B
Quantum®
Supplies PDUs

®
Completing Installation of the GRAFIK Eye®QS Control Unit
1.Mount the control unit in the wallbox as
shown using the four screws provided.
Note: Follow all local and national
electrical codes when installing IEC
PELV wiring with line voltage/mains
wiring.
2.Verify installation:
•Restore power.
•Press the top scene button. The LED will
light.
•Press the zone raise and lower buttons.
Make sure the control unit is dimming all
connected loads.
3.Apply the protective overlay to the control
unit.
Note: When tightening mounting
screws, make sure that the
hinged cover and faceplate
will open fully, as shown.
Wall
200 mm
87 mm
95 mm
Protective overlay
(apply after installation)
For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 9

Entering and Exiting Programming Mode
Entering programming mode:
Press and hold the top and bottom scene
buttons simultaneously for 3 seconds. The
LEDs in the scene buttons will scroll from
top to bottom, confirming that you are in
programming mode, and the info screen will
display the main menu.
Exiting programming mode:
Press and hold the top and bottom scene
buttons simultaneously for 3 seconds. The
info screen will go to Scene 1.
Navigating Menus in Programming Mode
Master Buttons
The Master buttons allow you to move through the menu
choices. The current choice is highlighted on the info screen.
OK Button
The OK button chooses the current highlighted menu choice.
This will either take you to the next menu or accept a setting you
have selected. When the screen displays a Yes/No question, the
OK button is “Yes”.
Timeclock Button
The Timeclock button functions as a “back” button during
programming mode. Pressing the timeclock button takes you
back one step in the current menu. Pressing it repeatedly
will eventually return you to the main menu, but will not exit
programming mode. When the screen displays a Yes/No
question, the Timeclock button is “No”.
®
Programming Mode
OK
1 2 3 4 5 6
Press and hold the top and
bottom buttons for 3 seconds
to enter or exit programming
mode
Master buttons
OK button
Timeclock (back) button
Main menu
Scene setup
Timeclock
Scene 1
Fade time
3 seconds
For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 10