Lutron Electronics GRAFIK Eye QS Owner's manual

The GRAFIK Eye QS with DALI®control unit allows for control
of both lights and window treatments, without interfaces, using
a single control unit. Features include pushbutton scene recall,
info screen that displays energy savings and status, IR receiver,
astronomic timeclock, contact closure input, and engravable
backlit buttons that are easy to find and operate. The built-in
DALI®bus link can control up to 64 DALI®devices.
Model Numbers: QSGRK-6D, QSGRK-8D, QSGRK-16D
QSGR-6D, QSGR-8D, QSGR-16D
QSGRM-6D, QSGRM-8D, QSGRM-16D
Ratings: 230 V~50/60 Hz 100 mA
Output: IEC PELV supply: 24 V-150 mA
DALI®Link: 18 V-250 mA
Contents
Features and Functions of the GRAFIK Eye QS with
DALI®Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Wiring the GRAFIK Eye QS with DALI®Control Unit
Overview of Line Voltage/Mains and DALI®Wiring. . . . . . . . . . . . . . . . 3
Line Voltage Wiring Details . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
DALI®Bus Wiring Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Overview of IEC PELV Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . 6
QS Link Control Wiring Details . . . . . . . . . . . . . . . . . . . . . . . . . 7
Power Group Wiring Example . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Completing Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Programming Mode
Entering and Exiting Programming Mode . . . . . . . . . . . . . . . . . . . 10
Navigating Menus in Programming Mode . . . . . . . . . . . . . . . . . . . 10
Wireless Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Zone Setup
Assigning Load Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Assigning Non-Dim Load Type . . . . . . . . . . . . . . . . . . . . . . . . 12
Scene Setup
Setting Zone Levels, Fade Rates, and Window Treatment
Group Actions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DALI®Setup
Building the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Assigning/Unassigning a DALI®Device to a Zone . . . . . . . . . . . . . . . 15
Occupancy Sensor Setup
Associating Wireless Occupancy Sensors. . . . . . . . . . . . . . . . . . . 16
Scene Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Daylight Sensor Setup
Associating Wireless Daylight Sensors . . . . . . . . . . . . . . . . . . . . 18
Zone Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Pico Wireless Control Setup
Associating with a GRAFIK Eye QS Wireless Control Unit. . . . . . . . . . . 20
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Wireless Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DALI®Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
For additional features and advanced functions, see the complete installation and
operation guide at www.lutron.com/qs
English DeutschEspañol Français Italiano
Quick Installation and
Operation Guide
Please Read
LUTRON
ѣᮽ
GRAFIK Eye QS with DALI®Control Unit

For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye QS with DALI®Control Unit Quick Installation and Operation Guide 2
OK
12345691011 12 13 14 7815 16
9-16
1-8
Features and Functions of the GRAFIK Eye QS with DALI®Control Unit
Info screen
Displays status or programming
functions
Page button
Switches between displaying
zones 1 to 8 and 9 to 16 on
16-zone unit
USB type mini B
For programming via PC
Scene buttons
With integral scene
indicator LEDs
Optional Shade
button groups
Preset and raise/lower buttons
with integral LEDs (maximum of
3 button groups)
Zone numbers
Zone raise/lower buttons
Zone LEDs display current
lighting zone levels
Timeclock button
Displays current timeclock info
OK button
Used for programming
Infrared receiver
For handheld remote use
Master buttons
Temporarily raise and lower
lighting levels on unit
Upper hinged faceplate
Lower hinged faceplate
Note: 6-zone control unit will show only zones 1 through 6.

For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye QS with DALI®Control Unit Quick Installation and Operation Guide 3
Wiring the GRAFIK Eye QS with DALI®Control Unit:
Overview of Line Voltage/Mains and DALI®Wiring
Two D1 and two D2 connections are provided for ease of wiring, and to provide two connecting points; there is only one
DALI®link on the unit.
Line Voltage/Mains
Cables and Load Wiring
DALI®Bus
Wiring
(See DALI®Bus
Wiring Details
section for complete
specification)
Terminal labels
L: Line / Hot
N: Neutral
: Ground
To additional DALI®devices
DALI®devices:
ballasts, drivers, or interfaces Distribution
Panel
D2 L
L
N
N
D2
D1
D1
2.5 mm2each terminal
230V~
50/60Hz
Distribution
Panel
Two 1.5 mm2each terminal*
* See page 7 for additional wiring options.

For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye QS with DALI®Control Unit Quick Installation and Operation Guide 4
Step 1: Install wallbox
• Mount a 89 mm deep, 4-gang U.S.
wallbox onto a dry, flat, indoor surface
that is accessible and allows for system
programming and operation.
• Allow at least 110 mm clearance above
and below the faceplate to ensure
proper heat dissipation. Allow 25 mm for
faceplate overhang on all sides.
Note: 4-gang wallbox available from
Lutron: P/N 241400.
Wiring the GRAFIK Eye QS with DALI®Control Unit:
Line Voltage Wiring Details
• Use properly certified cable for all line voltage/mains cables.
• Proper short-circuit and overload protection must be provided at the distribution panel.
• Install in accordance with all local and national electrical codes.
• IEC PELV terminals may be temporarily unplugged for ease of IR, occupancy sensor, and control wiring.
Step 2: Check control unit wiring
WARNING! Shock hazard. May
result in serious injury or death.
Always turn off circuit breaker or
remove main fuse from power line
before doing any work. Before
connecting the loads to the GRAFIK
Eye QS with DALI®control unit, test
the loads for short-circuits.
• Earth/ground terminal connection must
be made as shown in line voltage wiring
diagrams.
• Follow all local and national electrical
codes when installing IEC PELV wiring with
line voltage/mains wiring.
Step 3: Connect line voltage and loads
to control unit
• Strip 8 mm of insulation off the line
voltage/mains cables in the wallbox.
• Connect the line voltage/mains, ground,
and load wires to the appropriate terminals
on the back of the control unit.
L: Line / Hot
N: Neutral
: Ground
The recommended installation torque is
0.6 N∙m.
LUTRON
LUTRON
Allow 25 mm clearance on all sides
110 mm
8 mm
Notice: Risk of damage to unit.
• Do not connect line voltage/mains cable to IEC PELV terminals.
• Do not install control units to dim receptacles, motor-operated appliances, or
fluorescent lighting not equipped with DALI®electronic dimming ballasts, or other
DALI®devices approved for your location.
• Control units are designed for residential and commercial use, for indoor use only.
• Control units must be installed by a qualified electrician in accordance with all
applicable regulations and building codes.

For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye QS with DALI®Control Unit Quick Installation and Operation Guide 5
Wiring the GRAFIK Eye QS with DALI®Control Unit:
DALI®Bus Wiring Details
Step 1
• Use the wire size chart below to determine
which wire size to use based on the length
of the DALI®bus.
Wiring Size and Bus Length
DALI®bus wires D1 and D2 are not
polarity-sensitive. DALI®bus length is
limited by the wire gauge used for D1 and
D2 as follows:
Wire Gauge Maximum DALI®Bus Length
1.5 mm2275 m
1.0 mm2175 m
0.75 mm2150 m
0.5 mm2100 m
Step 2
WARNING! Shock hazard. May
result in serious injury or death.
Do NOT wire live. Interrupt power
via circuit breaker before wiring and
servicing the GRAFIK Eye QS with
DALI®control unit.
• Wire the DALI®bus from terminal D1 and
terminal D2 to all DALI®devices.
Step 3
• Turn on circuit breaker to energize.
DALI®Bus
18 V-250 mA
• DALI®terminal is double-insulated from QS and mains voltage
terminals.
• DALI®bus wiring may be run in the same conduit as mains wiring.
• Consult applicable national and local codes for compliance.
• Lutron recommends using two different colors for D1 and D2
(DALI® bus) wires. This will prevent wiring mistakes in junction
boxes where several different DALI®bus wires combine.
• Use the following instructions for wiring the DALI®bus.
– Each DALI®bus can have only 1GRAFIK Eye QS with DALI®
control unit connected to it. No additional DALI®bus supplies
can be on the link.
– Up to 64 DALI®devices can be connected to the DALI®bus.
• DALI®bus wiring cables (1.5 mm2) are available from Lutron:
P/N C-CBL-216-GR-1 and C-PCBL-216-CL-1.

For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye QS with DALI®Control Unit Quick Installation and Operation Guide 6
Note: Use appropriate wire connecting devices as specified by local codes.
* Do not connect terminal 2 between any GRAFIK Eye QS control unit and any other power supply,
including another GRAFIK Eye QS control unit.
See “Power Group Wiring” for a detailed wiring example.
Wiring the GRAFIK Eye QS with DALI®Control Unit:
Overview of IEC PELV Wiring
IR Wiring
1: IR DATA
2: IR COM
12
From external IR
connection (by others)
1.0 mm2each terminal
1234
1: COM
2: 24 V-*
3: MUX
4: MUX
To control stations,
window treatments,
or other
GRAFIK Eye QS
control units
QS Link Control Wiring
24 V-100 mA
Common and power
(terminals 1 and 2)
Two 1.0 mm2each terminal
Data
(terminals 3 and 4)
Twisted, shielded pair 0.5 mm2each terminal
Contact Closure Input Wiring
24 V-50 mA
For settings, see the full installation and
operation guide at www.lutron.com/qs
ABC
Example: Occupancy sensor (maximum 1)
A: CCI SIG
B: 24 V-
C: CCI COM
1.0 mm2each terminal

For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye QS with DALI®Control Unit Quick Installation and Operation Guide 7
Wiring the GRAFIK Eye QS with DALI®Control Unit:
QS Link Control Wiring Details
• System communication uses IEC PELV wiring.
• Follow all local and national electrical codes when installing IEC PELV wiring with
line voltage/mains wiring.
• Each QS link terminal can accept
only two 18 AWG (1.0 mm2)
wires (two 12 AWG [4.0 mm2]
conductors will not fit). Connect
using appropriate wire connectors
as shown to the right.
• Total length of control link must
not exceed 610 m.
• Make all connections in the
control unit’s wallbox.
• Wiring can be T-tapped or
daisy-chained.
• IEC PELV 24 V-150 mA.
System Limits
The QS wired communication
link is limited to 100 devices or
100zones.
The GRAFIK Eye QS control unit supplies 3Power
Draw Units (PDUs) on the QS link. Refer to the
QS Link Power Draw Units specification submittal
(Lutron P/N 369405) for more information about
Power Draw Units.
Wire Sizes (check compatibility in your area)
QS Link Wiring Length Wire Gauge Lutron Cable Part Number
Less than 153 m Power (terminals 1 and 2): 1 pair 1.0 mm2GRX-CBL-346S; GRX-PCBL-346S
Data (terminals 3 and 4): 1 twisted, shielded pair 0.5 mm2
153 to 610 m Power (terminals 1 and 2): 1 pair 4.0 mm2GRX-CBL-46L; GRX-PCBL-46L
Data (terminals 3 and 4): 1 twisted, shielded pair 0.5 mm2
T-Tap Wiring Example
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
GRAFIK Eye QS with
DALI®control unit
Sivoia QS
window
treatment/
drape
seeTouch QS
wallstation
To DALI®link 1
To DALI®link 2
QS smart
power
panel
Daisy-Chain Wiring Example
LUTRON
LUTRON
LUTRON
LUTRONLUTRON
LUTRON
LUTRON
seeTouch QS
wallstations
QS smart
power panel
GRAFIK Eye QS
with DALI®
control unit
GRAFIK Eye QS
with DALI®
control unit
To DALI®link 1 To DALI®link 2
Sivoia QS
window
treatment/
drape
4.0 mm2
1.5 mm2

For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye QS with DALI®Control Unit Quick Installation and Operation Guide 8
Wiring the GRAFIK Eye QS with DALI®Control Unit:
Power Group Wiring Example
On the QS link, some devices supply power and some devices consume power. Each device has a specific number of Power Draw Units
(PDUs) that it either supplies or consumes. A Power Group consists of one device that supplies power and one or more devices that
consume power; each Power Group may have only one power-supplying device. Refer to the QS Link Power Draw Units specification
submittal (Lutron P/N 369405) for more information about PDUs.
Within Power Groups on the QS link, connect all 4 terminals (1, 2, 3, and 4), shown by the letter A in the diagram. Between devices on the
QS link that supply power, connect only terminals 1, 3, and 4 (NOT terminal 2), shown by the letter B on the diagram.
Wiring can be T-tapped or daisy-chained.
LUTRON
Power Group 1
Power Group 2
Power Group 3
(Do NOT connect terminal 2: 24 V-)
(Do NOT connect terminal 2: 24 V-)
(Do NOT connect terminal 2: 24 V-)
GRAFIK Eye QS
control unit
Supplies PDUs
Quantum panel
Supplies PDUs
QS Power Supply
Supplies PDUs
Energi Savr Node
unit Supplies PDUs
Control Interfaces
Consume PDUs
Control Interfaces
Consume PDUs
Wallstations
Consume PDUs
Wallstations
Consume PDUs
Wallstations
Consume PDUs
QS Sensor Module with
Occupancy Sensor
Consumes PDUs
B
A
A
B
A
B
Connect all 4 terminals within a
power group:
1: Common
2: 24 V-
3 and 4: Data
Connect only 3 terminals between
power groups:
1: Common
2: 24 V-Do NOT connect
3 and 4: Data
A
B

For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye QS with DALI®Control Unit Quick Installation and Operation Guide 9
Completing Installation of the GRAFIK Eye QS with DALI®Control Unit
1. Mount the control unit in the wallbox as
shown using the four screws provided.
Note: Follow all local and national electrical
codes when installing IECPELV/
NEC®Class 2 wiring with line
voltage/mains wiring.
2. Verify installation:
• Restore power.
• Press the top scene button. The LED will
light.
• Press the zone raise and lower buttons.
Make sure the control unit is dimming all
connected loads.
3. Apply the protective overlay to the control
unit.
Wall
87 mm 95 mm
200 mm
Protective overlay
(apply after installation)
Note: When tightening mounting
screws, make sure that the hinged
cover and faceplate will open fully,
as shown.

For additional information, see the complete installation and operation guide at www.lutron.com/qs
GRAFIK Eye QS with DALI®Control Unit Quick Installation and Operation Guide 10
Programming Mode
Entering and Exiting Programming Mode
Entering programming mode
Press and hold the top and bottom scene buttons
simultaneously for 3 seconds. The LEDs in the scene
buttons will scroll from top to bottom, confirming that you
are in programming mode, and the info screen will display
the main menu.
Exiting programming mode
Press and hold the top and bottom scene buttons
simultaneously for 3 seconds. The info screen will go to
Scene 1.
Navigating Menus in Programming Mode
Master Buttons
The Master buttons allow you to move through the menu choices. The current
choice is highlighted on the info screen.
OK Button
The OK button chooses the current highlighted menu choice. This will either take you to the next menu or accept a setting you have
selected. When the screen displays a Yes/No question, the OK button is “Yes”.
Timeclock Button
The timeclock button functions as a “back” button during programming mode. Pressing the timeclock button takes you back one step in
the current menu. Pressing it repeatedly will eventually return you to the main menu, but will not exit programming mode. When the screen
displays a Yes/No question, the Timeclock button is “No”.
Main Menu
Timeclock
Scene Setup
Scene 1
Fade Time
3Seconds
OK
16
9-16
1-8
Master buttons
OK button
Timeclock (back)
button
Press and hold the
top and bottom
buttons for 3 seconds
to enter or exit
programming mode