Luxibel LXMH10003 User manual

LXMH10003
7 X 15 W OSRAM 4-IN-1 LED MOVING HEAD
USER MANUAL

LXMH10003
V. 01 –03/12/2015 2 ©Velleman nv

LXMH10003
V. 01 –03/12/2015 3 ©Velleman nv
USER MANUAL
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle
could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal
waste; it should be taken to a specialized company for recycling. This device should be returned
to your distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Luxibel®! Please read the manual thoroughly before bringing this device into
service. If the device was damaged in transit, do not install or use it and contact your dealer.
2. Safety Instructions
Be very careful during the installation: touching live wires can cause life-threatening
electroshocks.
Always disconnect mains power when device not in use or when servicing or
maintenance activities are performed. Handle the power cord by the plug only.
Indoor use only. Keep this device away from rain, moisture, splashing and dripping
liquids. Never put objects filled with liquids on top of or close to the device.
Keep this device away from children and unauthorized users.
Caution: device heats up during use.
Do not stare directly at the light source, as this may cause
epileptic seizure in sensitive people
temporarily loss of sight (flash blindness)
permanent (irreversible) eye damage.
There are no user-serviceable parts inside the device. Refer to an authorized dealer for
service and/or spare parts.
Respect a minimum distance of 0.5 m between the device’s light output and any
illuminated surface.
This is a Safety Class 1 device. It is therefore essential that the device be earthed. Have
a qualified person carry out the electric connection.
Make sure that the available voltage does not exceed the voltage stated in the specifications of this
manual.
Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if
necessary.
Use an appropriate safety cable to fix the device (e.g. VDLSC7N or VDLSC8N).
Install the device at a minimal distance of 0.5 m from flammable and explosive objects or
substances.
The maximum ambient temperature is 40 °C. Do not operate the device at higher temperatures.

LXMH10003
V. 01 –03/12/2015 4 ©Velleman nv
3. General Guidelines
Refer to the Velleman®Service and Quality Warranty on the last pages of this manual.
Keep this device away from dust and extreme temperatures. Make sure the ventilation
openings are clear at all times. For sufficient air circulation, leave at least 1" (± 2.5 cm)
in front of the openings.
Protect this device from shocks and abuse. Avoid brute force when operating the device.
Familiarise yourself with the functions of the device before actually using it. Do not allow operation
by unqualified people. Any damage that may occur will most probably be due to unprofessional use
of the device.
All modifications of the device are forbidden for safety reasons. Damage caused by user modifications
to the device is not covered by the warranty.
Only use the device for its intended purpose. All other uses may lead to short circuits, burns,
electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the
warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and
the dealer will not accept responsibility for any ensuing defects or problems.
Mechanical wear and LEDs are not covered by warranty.
A qualified technician should install and service this device.
Do not switch the device on immediately after it has been exposed to changes in temperature.
Protect the device against damage by leaving it switched off until it has reached room temperature.
This device is designed for professional use on stage, in discos, theatres, etc. The device should only
be used indoors with an alternating current of 100-240 V~, 50/60 Hz.
Lighting effects are not designed for permanent operation: regular operation breaks will prolong their
lives.
Use the original packaging if the device is to be transported.
Product images are for illustrative purposes only.
Keep this manual for future reference.
4. Features
DMX channels: 19/50/18/20
super-fast, smooth and silent movement
7 LEDs with pixel control
RGBW four-colour mixing creates vivid, saturated and uniform colour effects
pre-set colour temperature at 2700 K, 3200 K, 4200 K, 5600 K and 8000 K
zoom from 10° to 60°
full-range 0-100 % dimmer
various strobe effects
RDM (Remote Device Management) function to change DMX address, display flip, X/Y reverse…
software upgrade via DMX
adjustable sleep mode when DMX signal is lost
temperature indication for base, arm and lamp
fan speed changes automatically depending on temperature
heat pipe for cooling
W-DMX for wireless DMX transmission

LXMH10003
V. 01 –03/12/2015 5 ©Velleman nv
5. Mounting and Connection
Choose a suitable mounting spot. Mount the device in the desired angle using the included bracket.
Connect the power cord to the mains. Disconnect after use.
5.1 Mounting the Device
Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable norms.
The carrying construction must be able to support 10 times the weight of the device for 1 hour
without deforming.
The installation must always be secured with a secondary attachment e.g. a safety cable.
Never stand directly below the device when it is being mounted, removed or serviced. Have a
qualified technician check the device once a year and once before you bring it into service.
Install the device in a location with few passers-by that is inaccessible to unauthorised persons.
Overhead mounting requires extensive experience: calculating workload limits, determining the
installation material to be used… Have the material and the device itself checked regularly. Do not
attempt to install the device yourself if you lack these qualifications as improper installation may
result in injuries.
For truss mounting, use an appropriate clamp (not incl.) and fit an M10 bolt through the centre of the
(folded) bracket.
Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.
Make sure there is no flammable material within a 0.5 m radius of the device.
Have a qualified electrician carry out the electric connection.
Connect the device to the mains with the power plug. All devices must be powered directly off a
grounded switched circuit. Do not connect to a dimmer pack.
The device has a power output to supply power to another device. When connecting several devices
in a daisy chain via this output, make sure that the total current does not exceed the power line’s
nominal current. Use power cables with an adequate section.
The installation has to be approved by an expert before the device is taken into service.
1. Install the clamp onto the Omega bracket.
2. Install the clamp-bracket assembly onto the device.
3. Install the assembly onto an appropriate truss and fasten. Secure with a secondary safety rope.
5.2 Connecting the Device
Power
Connect the device to the mains with the power plug.
Power all devices directly off a grounded switched circuit.
Do not connect the device to a rheostat or dimmer circuit, even when using the rheostat or dimmer
channel solely for 0 % to 100 % switching.
Have a qualified electrician carry out the electric connection.

LXMH10003
V. 01 –03/12/2015 6 ©Velleman nv
DMX-512 Connection
When applicable, connect an XLR cable to the female XLR output of a controller (not incl.) and the
other side to the male XLR input of the device. Multiple devices can be linked through serial linking.
The linking cable shall be a dual core, screened cable with XLR input and output connectors.
A DMX terminator is recommended for installations where the DMX cable has to run a long distance or is
in an electrically noisy environment (e.g. discos). The terminator prevents corruption of the digital
control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor
between pins 2 and 3, which is then plugged into the XLR output socket of the last device in the chain.
terminator
How to turn the controller line from 3-pins into 5-pins (plug and socket).
6. Operation
The device can be used in the following modes:
stand-alone mode
master/slave mode
with a DMX-512 controller.
6.1 Control Panel
Access the control panel functions using the four panel buttons located around the display:
Button
Function
MENU
access the menu
return to a previous menu option
ENTER
select menu option
store the current menu or option within the menu

LXMH10003
V. 01 –03/12/2015 7 ©Velleman nv
Button
Function
UP
scroll through the menu options in ascending order
increase value
DOWN
scroll through the menu options in descending order
decrease value
Menu
Connect
DMX Address
①
XXX
DMX address
setting
Wireless①
Wireless
Enabled
Light
Max
Temperature
①
80~139℃, 90℃/176~282℉,194℉
Lamp off if
temperature
continuously
over for 5
minutes
Lamp Adjust
①
PAN……
Adjust value of
each channels
Information
Time Info.
Current XXXX(Hours)
Fixture Life XXXX(Hours)
Fixture boot
time
Fixture total
run time
Temperature
Near Lamp Temp (depends on fixture)
Temperature
Sensors
Fans Speed
Near Lamp Fan (depends on fixture)
Fan speed
Sensors
Channel
Value
PAN……
Display value
of channel
Error
Message
Pan,Tilt……
Error channels
Fixture Model
xxxxxxxxxxxx
Display model
brand and
model

LXMH10003
V. 01 –03/12/2015 8 ©Velleman nv
Software Ver
1U01 V1.0.00
2U01 V1.0.00
:
Version of each
IC
Set
Reset
All
Pan&Tilt
Others
Reset all
Reset Pan&Tilt
Reset Others
Movment
Pan Reverse①
Tilt Reverse①
Pan Degree①
Encoders①
Pan/Tilt Mode①
ON/OFF
ON/OFF
630/540
ON/OFF
Stand/Smooth
Pan Reverse
Tilt Reverse
Choose Pan
Degree
Encoder wheel
on/off
Choose pan/tilt
mode
UI Set
Mic Sens. ③
No Signal①
Temperature. C/F①
Fans Mode①
Hibernation①
Backlight①
Flip Display①
Display Bright③
Brand Show①
Key Lock①
Language①
0~99%,60%
Close/Hold/Auto/Music
Fahrenheit /Celsius
Auto Speed /High Speed
OFF, 01M~99M，15M
02~60m 02m
ON/OFF
00~31 10
ON/OFF
ON/OFF
En/简/繁/Fr/Sp
Sensitivity of
Mic
Mode when no
signal
Temperature at
℃/℉
Fans mode
Sleeping mode
Show backlight
time
Display 180°
reverse
Display
Brightness
Show brand or
not
Key lock on/off
Language
Select

LXMH10003
V. 01 –03/12/2015 9 ©Velleman nv
Users
User Mode①
Standard
Extended
Basic-8bit
Basic-16bit
User
Standard mode
Extended mode
Basic-8bit
mode
Basic-16bit
mode
User program
mode
Edit User③
Max Channel = XX
PAN = CH01
:
Edit users
mode
Calibration③
-Password-
Pan..
=XXX
=XXX
Password: 050
Calibrate
channel value
Fixture ID③
Name
-Password-
PID Code
Name
Password: 050
Set PID of RDM
Wireless Set
①
DMX On Cable
Reset Connect
ON/OFF
ON/OFF
DMX Send Out
Reset Connect
Reload
Default
Basic Reload(①)
Program Reload(②)
---Password---
Private Reload(③)
All Reload
ON/OFF
ON/OFF
XXX
ON/OFF
ON/OFF
Basic Reload
Program
Reload
Password: 050
Private Reload
All Reload
Program
Play①
DMX Receive
Slave Receive
Sequence
Music
Slave Receive 1,2,3
Master / Alone
Master / Alone
DMX Receive
Choose slave
position
Run Sequence
Music mode

LXMH10003
V. 01 –03/12/2015 10 ©Velleman nv
Select Chase
②
Chase Part 1
Chase Part 2
Chase Part 3
Chase 1 ~ 8 Chase 1
Chase 1 ~ 8 Chase 2
Chase 1 ~ 8 Chase 3
Select and run
auto program
Edit Chase②
Chase 1
:
Chase 8
Chase Test
Step 01
Step 64
=SCxxx
=SCxxx
Test
Beginning
scene
Ending scene
Edit Scenes②
Edit Scene
001
~ Edit Scene
250
Pan,Tilt,……
--Fade
Time--
--Secne
Time--
DMX Input
=xxx
=xxx
=xxx
Input manual
scene
Modify
manually
fading time
Modify
manually
scene time
Input scene
from exterior
controller
Scenes
Record
ScXX=>ScXX
Auto Input
scenes
Remarks
xxxx
default setting
①
basic relaod
②
programme reload
③
private reload