Luxor STANDUP-CF60 User manual

2 / 12
Table of Contents
Table of Contents ........................................ 2
Parts List & Hardware ..................................... 3
Assembly and Installation
Assembly of the right and left frame ............................ 4
Place the crank adjustment housing ............................ 5
Attach the crank adjustment housing ........................... 6
Assembly of the cross bars. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Flip desk upright and attach the crank handle ..................... 8
Fasten the rotating hex rod................................... 9
Attach the desk surface ..................................... 10
Finish assembly and tighten bolts .............................. 11
ATTENTION!
Do not fully tighten screws until completely assembled
TOOLS NEEDED:
Mallet
WE ARE GIVING YOU A STANDING OVATION
You did it! You took the rst step towards healthier living by purchasing
our stand up desk. We couldn’t be happier to have you joining the millions
of people who were tired of sitting around and ready to take a stand for a
healthier life.
This desk was built with you in mind and every detail was carefully crafted. The
following assembly guide is best accomplished with two people. If you have any
questions or concerns contact your local dealer.

3 / 12
DB x1
DC x1
DA x1
AA x1 CA x1
FA x2
AB x1 JA x1
HA x1
CB*x17
M8x15
FB*x5
M6x48
JB*x5
M6x73
KB*x3
M6x36
M5
M4
M4
GA x1BA x2 BB x2 MA x4AC x4
EA x1
HB x1 HC x1
- Includes an
extra spare part
*
Includes
locking bolt

4 / 12
Gather Parts:
AA, AB, AC,
BA, BB, EA
AA
AB
BA
BA
BB
BB
EA
AC
AC
AC
AC
1Assembly of the right and left frame
Mallet
Tighten casters
fully with included
wrench

5 / 12
2
Gather Parts:
CA
CA
Place the crank adjustment housing
Assistance
Recommended

3
Gather Parts:
DA +
CB x16
M8x15
CBx4
CBx4
CBx4
CBx4
DA
CA
CA
CA
6 / 12
Attach the crank adjustment housing

7 / 12
4
+
Gather Parts:
FA, DB
FB x4
M6x48
AA
FA
FA
FA
AB
FB
FB
FB
FB
DB
Assistance
Recommended
Make sure the indented center
hole of the cross bars FA are
facing towards the casters
Assembly of the cross bars

8 / 12
5
1
2
Gather Parts:
GA
GA
GAx1
Assistance
Recommended
Flip desk upright and attach crank handle
IMPORTANT: Install the OPTIONAL
electric (SOLD SEPARATELY) before
attaching the desk top to the frame.
Handle should have only
13/4” of clearance when
attached correctly.

9 / 12
6
Gather Parts:
DC
HB
HC
HA
HA
HA
21
3
4
HA
HA DC
HB
HB
HC
Fasten the rotating hex rod
With allen wrench DC
fasten the locking bolt
HB clock-wise until the
nut locks in place.
HB x1 HC x1
Includes
locking bolt
+

10 / 12
7
+
Gather Parts:
JA JB x4
M6x73
JA
JB
JB
JB JB
DB
Assistance
Recommended
Attach the desk surface

11 / 12
8
KB x2
M6x36
KB
KB
DB
+
Gather Parts:
MA
MA x4
Finish assembly and tighten bolts

06/07/2016