Luxul Xen XGS-1008 User manual

READ ME FIRST
Fold Fold Fold
QUICK INSTALL GUIDE
8-Port Gigabit Desktop Switch
XGS-1008
Includes:
One: XGS-1008 8-Port Gigabit Desktop Switch
One: Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1008 in a stable/safe place to avoid any possible damage. Avoid
placement in direct sunlight and do not place heavy articles on the XGS-1008.
Ensure there is adequate space for proper heat dissipation and ventilation
around the switch.
XGS-1008 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet near the XGS-1008,
then connect the power adapter plug to the switch power connector.
XGS-1008 Rear Panel Detail with DC Power Connector
cCAUTION: Use only the included power supply. If a dierent power
supply is used, it could damage the XGS-1008.
Sales
P: 801-822-5450
Technical Support
P: 801-822-5450 Option 3
LUX-QIG-XGS-1008-v2 05131612
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied
license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and
Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other
trademarks and registered trademarks are property of their respective holders.

READ ME FIRST
Fold Fold Fold
QUICK INSTALL GUIDE
8-Port Gigabit Desktop Switch
XGS-1008
Includes:
One: XGS-1008 8-Port Gigabit Desktop Switch
One: Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1008 in a stable/safe place to avoid any possible damage. Avoid
placement in direct sunlight and do not place heavy articles on the XGS-1008.
Ensure there is adequate space for proper heat dissipation and ventilation
around the switch.
XGS-1008 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet near the XGS-1008,
then connect the power adapter plug to the switch power connector.
XGS-1008 Rear Panel Detail with DC Power Connector
cCAUTION: Use only the included power supply. If a dierent power
supply is used, it could damage the XGS-1008.
Sales
P: 801-822-5450
Technical Support
P: 801-822-5450 Option 3
LUX-QIG-XGS-1008-v2 05131612
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied
license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and
Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other
trademarks and registered trademarks are property of their respective holders.

READ ME FIRST
Fold Fold Fold
QUICK INSTALL GUIDE
8-Port Gigabit Desktop Switch
XGS-1008
Includes:
One: XGS-1008 8-Port Gigabit Desktop Switch
One: Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1008 in a stable/safe place to avoid any possible damage. Avoid
placement in direct sunlight and do not place heavy articles on the XGS-1008.
Ensure there is adequate space for proper heat dissipation and ventilation
around the switch.
XGS-1008 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet near the XGS-1008,
then connect the power adapter plug to the switch power connector.
XGS-1008 Rear Panel Detail with DC Power Connector
cCAUTION: Use only the included power supply. If a dierent power
supply is used, it could damage the XGS-1008.
Sales
P: 801-822-5450
Technical Support
P: 801-822-5450 Option 3
LUX-QIG-XGS-1008-v2 05131612
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied
license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and
Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other
trademarks and registered trademarks are property of their respective holders.

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1008 to Ethernet devices
as shown below. Luxul recommends Category-5, super Category-5
or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP). To
ensure best performance and stable data transmission at 1000 Mbps, use
Category-6 shielded twisted pair.
Connecting the XGS-1008 to a Device
When a device is properly connected, the Link/Activity LEDs for each port
lights up green/orange. Please refer to the section on LED Indicators for
definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports, Luxul recommends
connecting LAN devices to the XGS-1008, then connecting the switch to a
router LAN port or another switch as shown in the illustration.
Internet
Connecting the XGS-1008 to a Router or Switch
When devices are properly connected, the Link/Activity LEDs for each port
light up green/orange. Refer to the section on LED Indicators for definitions
and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1008 includes eight Link/Activity LEDs and one
power LED. For more information on these LEDs, refer to the table describing
these indicators in the next section.
XGS-1008 Front Panel View
XGS-1008 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1008 include one Power indicator and 8 Link/
Activity indicators. These LED indicators show the operating status of the
XGS-1008 and each switch connection.
The following chart shows the LED indicators of the XGS-1008 along with a
description of each indicator:
LED Color Status Description
Power Green On The XGS-1008 is powered.
O The XGS-1008 is unpowered. Check
the DC power supply to ensure proper
connection to the outlet and switch.
Link/
Activity
Green On The XGS-1008 is connected at
1000Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 1000Mbps.
Orange On The XGS-1008 is connected at
10/100Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 10/100Mbps.
O Indicates the port is not connected to
a device.

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1008 to Ethernet devices
as shown below. Luxul recommends Category-5, super Category-5
or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP). To
ensure best performance and stable data transmission at 1000 Mbps, use
Category-6 shielded twisted pair.
Connecting the XGS-1008 to a Device
When a device is properly connected, the Link/Activity LEDs for each port
lights up green/orange. Please refer to the section on LED Indicators for
definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports, Luxul recommends
connecting LAN devices to the XGS-1008, then connecting the switch to a
router LAN port or another switch as shown in the illustration.
Internet
Connecting the XGS-1008 to a Router or Switch
When devices are properly connected, the Link/Activity LEDs for each port
light up green/orange. Refer to the section on LED Indicators for definitions
and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1008 includes eight Link/Activity LEDs and one
power LED. For more information on these LEDs, refer to the table describing
these indicators in the next section.
XGS-1008 Front Panel View
XGS-1008 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1008 include one Power indicator and 8 Link/
Activity indicators. These LED indicators show the operating status of the
XGS-1008 and each switch connection.
The following chart shows the LED indicators of the XGS-1008 along with a
description of each indicator:
LED Color Status Description
Power Green On The XGS-1008 is powered.
O The XGS-1008 is unpowered. Check
the DC power supply to ensure proper
connection to the outlet and switch.
Link/
Activity
Green On The XGS-1008 is connected at
1000Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 1000Mbps.
Orange On The XGS-1008 is connected at
10/100Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 10/100Mbps.
O Indicates the port is not connected to
a device.

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1008 to Ethernet devices
as shown below. Luxul recommends Category-5, super Category-5
or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP). To
ensure best performance and stable data transmission at 1000 Mbps, use
Category-6 shielded twisted pair.
Connecting the XGS-1008 to a Device
When a device is properly connected, the Link/Activity LEDs for each port
lights up green/orange. Please refer to the section on LED Indicators for
definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports, Luxul recommends
connecting LAN devices to the XGS-1008, then connecting the switch to a
router LAN port or another switch as shown in the illustration.
Internet
Connecting the XGS-1008 to a Router or Switch
When devices are properly connected, the Link/Activity LEDs for each port
light up green/orange. Refer to the section on LED Indicators for definitions
and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1008 includes eight Link/Activity LEDs and one
power LED. For more information on these LEDs, refer to the table describing
these indicators in the next section.
XGS-1008 Front Panel View
XGS-1008 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1008 include one Power indicator and 8 Link/
Activity indicators. These LED indicators show the operating status of the
XGS-1008 and each switch connection.
The following chart shows the LED indicators of the XGS-1008 along with a
description of each indicator:
LED Color Status Description
Power Green On The XGS-1008 is powered.
O The XGS-1008 is unpowered. Check
the DC power supply to ensure proper
connection to the outlet and switch.
Link/
Activity
Green On The XGS-1008 is connected at
1000Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 1000Mbps.
Orange On The XGS-1008 is connected at
10/100Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 10/100Mbps.
O Indicates the port is not connected to
a device.

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1008 to Ethernet devices
as shown below. Luxul recommends Category-5, super Category-5
or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP). To
ensure best performance and stable data transmission at 1000 Mbps, use
Category-6 shielded twisted pair.
Connecting the XGS-1008 to a Device
When a device is properly connected, the Link/Activity LEDs for each port
lights up green/orange. Please refer to the section on LED Indicators for
definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports, Luxul recommends
connecting LAN devices to the XGS-1008, then connecting the switch to a
router LAN port or another switch as shown in the illustration.
Internet
Connecting the XGS-1008 to a Router or Switch
When devices are properly connected, the Link/Activity LEDs for each port
light up green/orange. Refer to the section on LED Indicators for definitions
and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1008 includes eight Link/Activity LEDs and one
power LED. For more information on these LEDs, refer to the table describing
these indicators in the next section.
XGS-1008 Front Panel View
XGS-1008 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1008 include one Power indicator and 8 Link/
Activity indicators. These LED indicators show the operating status of the
XGS-1008 and each switch connection.
The following chart shows the LED indicators of the XGS-1008 along with a
description of each indicator:
LED Color Status Description
Power Green On The XGS-1008 is powered.
O The XGS-1008 is unpowered. Check
the DC power supply to ensure proper
connection to the outlet and switch.
Link/
Activity
Green On The XGS-1008 is connected at
1000Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 1000Mbps.
Orange On The XGS-1008 is connected at
10/100Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 10/100Mbps.
O Indicates the port is not connected to
a device.

READ ME FIRST
Fold Fold Fold
QUICK INSTALL GUIDE
8-Port Gigabit Desktop Switch
XGS-1008
Includes:
One: XGS-1008 8-Port Gigabit Desktop Switch
One: Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1008 in a stable/safe place to avoid any possible damage. Avoid
placement in direct sunlight and do not place heavy articles on the XGS-1008.
Ensure there is adequate space for proper heat dissipation and ventilation
around the switch.
XGS-1008 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet near the XGS-1008,
then connect the power adapter plug to the switch power connector.
XGS-1008 Rear Panel Detail with DC Power Connector
cCAUTION: Use only the included power supply. If a dierent power
supply is used, it could damage the XGS-1008.
Sales
P: 801-822-5450
Technical Support
P: 801-822-5450 Option 3
LUX-QIG-XGS-1008-v2 05131612
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied
license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and
Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other
trademarks and registered trademarks are property of their respective holders.
Other manuals for Xen XGS-1008
4
Table of contents
Other Luxul Switch manuals

Luxul
Luxul XMS-2624P User manual

Luxul
Luxul AMS-2600 User manual

Luxul
Luxul XMS-1024P User manual

Luxul
Luxul XFS-1816P User manual

Luxul
Luxul XFS-1084P User manual

Luxul
Luxul Xen XGS-1008 User manual

Luxul
Luxul XFS-1816P User manual

Luxul
Luxul XMS-5248P User manual

Luxul
Luxul XGS-1024 User manual

Luxul
Luxul AGS-1024 User manual

Luxul
Luxul AMS-1208P User manual

Luxul
Luxul AMS-1208P User manual

Luxul
Luxul XMS-1024P User manual

Luxul
Luxul AMS-1816P User manual

Luxul
Luxul SW-510-48P-F User manual

Luxul
Luxul AGS-1008M User manual

Luxul
Luxul Xen XGS-1008 User manual

Luxul
Luxul XGS-1005 User manual

Luxul
Luxul Xen XGS-1008 User manual

Luxul
Luxul AMS-4424P User manual