Luxul XGS-1005 User manual

Fold Fold Fold
READ ME FIRST
QUICK
INSTALL
GUIDE
5-Port Gigabit Switch
XGS-1005
Includes:
XGS-1005 5-Port Gigabit Switch
Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1005 in a stable/safe place to avoid any
possible damage. Avoid placement in direct sunlight and
do not place heavy articles on the XGS-1005.
Ensure there is adequate space for proper heat dissipa-
tion and ventilation around the switch.
XGS-1005 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet
near the XGS-1005, then connect the power adapter plug
to the switch power connector.
XGS-1005 Rear Panel Detail View
cCAUTION: Use only the included power supply.
If a dierent power supply is used, it
could damage the XGS-1005.
LUX-QIG-XGS-1005-v3 0321703
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any pur-
poses without permission in writing from Luxul. The material in this document
is subject to change without notice. Luxul reserves the right to make changes
to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual
property rights. An implied license only exists for equipment, circuits and
subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the
Luxul logo mark and Simply Connected are all trademarks and or registered
trademarks of Luxul Wireless, Inc. All other trademarks and registered
trademarks are property of their respective holders.
Sales
P: 801-822-5450
E: [email protected]om
Technical Support
P: 801-822-5450 Option 3
E: [email protected]

Fold Fold Fold
READ ME FIRST
QUICK
INSTALL
GUIDE
5-Port Gigabit Switch
XGS-1005
Includes:
XGS-1005 5-Port Gigabit Switch
Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1005 in a stable/safe place to avoid any
possible damage. Avoid placement in direct sunlight and
do not place heavy articles on the XGS-1005.
Ensure there is adequate space for proper heat dissipa-
tion and ventilation around the switch.
XGS-1005 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet
near the XGS-1005, then connect the power adapter plug
to the switch power connector.
XGS-1005 Rear Panel Detail View
cCAUTION: Use only the included power supply.
If a dierent power supply is used, it
could damage the XGS-1005.
LUX-QIG-XGS-1005-v3 0321703
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any pur-
poses without permission in writing from Luxul. The material in this document
is subject to change without notice. Luxul reserves the right to make changes
to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual
property rights. An implied license only exists for equipment, circuits and
subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the
Luxul logo mark and Simply Connected are all trademarks and or registered
trademarks of Luxul Wireless, Inc. All other trademarks and registered
trademarks are property of their respective holders.
Sales
P: 801-822-5450
E: [email protected]om
Technical Support
P: 801-822-5450 Option 3
E: [email protected]

Fold Fold Fold
READ ME FIRST
QUICK
INSTALL
GUIDE
5-Port Gigabit Switch
XGS-1005
Includes:
XGS-1005 5-Port Gigabit Switch
Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1005 in a stable/safe place to avoid any
possible damage. Avoid placement in direct sunlight and
do not place heavy articles on the XGS-1005.
Ensure there is adequate space for proper heat dissipa-
tion and ventilation around the switch.
XGS-1005 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet
near the XGS-1005, then connect the power adapter plug
to the switch power connector.
XGS-1005 Rear Panel Detail View
cCAUTION: Use only the included power supply.
If a dierent power supply is used, it
could damage the XGS-1005.
LUX-QIG-XGS-1005-v3 0321703
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any pur-
poses without permission in writing from Luxul. The material in this document
is subject to change without notice. Luxul reserves the right to make changes
to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual
property rights. An implied license only exists for equipment, circuits and
subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the
Luxul logo mark and Simply Connected are all trademarks and or registered
trademarks of Luxul Wireless, Inc. All other trademarks and registered
trademarks are property of their respective holders.
Sales
P: 801-822-5450
E: [email protected]om
Technical Support
P: 801-822-5450 Option 3
E: [email protected]

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1005
to Ethernet devices as shown below. Luxul recommends
Category-5, super Category-5 or Category-6 unshielded
twisted pair (CAT5/CAT5e/CAT6 UTP). To ensure best
performance and stable data transmission at 1000 Mbps,
use Category-6 shielded twisted pair.
Connecting the XGS-1005 to a Device
When a device is properly connected, the Link/Activity
LED for the port to which the device is connected lights
up green. Please refer to the section on LED Indicators
for definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports,
Luxul recommends connecting LAN devices to the
XGS-1005, then connecting the switch to a router LAN
port or another switch as shown in the illustration.
Internet
Connecting the XGS-1005 to a Router or Switch
When the XGS-1005 is properly connected to a router
or switch, the Link/Activity LED for the appropriate port
lights up green. Refer to the section on LED Indicators for
definitions and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1005 includes five Link/
Activity LEDs and one Power LED. For more information
on these LEDs, refer to the table describing these
indicators in the next section.
XGS-1005 Front Panel View
XGS-1005 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1005 include one Power
indicator and 5 Link/Activity indicators. These LED
indicators show the operating status of the XGS-1005
and each switch connection.
The following chart shows the LED indicators of the
XGS-1005 along with a description of each indicator:
LED Color Status Description
Power Green On The switch is powered.
O The switch is unpowered.
Check the DC power
supply to ensure proper
connection to the outlet
and switch.
Link/
Activity
Green On The switch is connected
to an Ethernet device.
Blinking The switch is
transmitting/receiving
data packets.
O Indicates the port is
not connected to an
Ethernet device.

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1005
to Ethernet devices as shown below. Luxul recommends
Category-5, super Category-5 or Category-6 unshielded
twisted pair (CAT5/CAT5e/CAT6 UTP). To ensure best
performance and stable data transmission at 1000 Mbps,
use Category-6 shielded twisted pair.
Connecting the XGS-1005 to a Device
When a device is properly connected, the Link/Activity
LED for the port to which the device is connected lights
up green. Please refer to the section on LED Indicators
for definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports,
Luxul recommends connecting LAN devices to the
XGS-1005, then connecting the switch to a router LAN
port or another switch as shown in the illustration.
Internet
Connecting the XGS-1005 to a Router or Switch
When the XGS-1005 is properly connected to a router
or switch, the Link/Activity LED for the appropriate port
lights up green. Refer to the section on LED Indicators for
definitions and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1005 includes five Link/
Activity LEDs and one Power LED. For more information
on these LEDs, refer to the table describing these
indicators in the next section.
XGS-1005 Front Panel View
XGS-1005 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1005 include one Power
indicator and 5 Link/Activity indicators. These LED
indicators show the operating status of the XGS-1005
and each switch connection.
The following chart shows the LED indicators of the
XGS-1005 along with a description of each indicator:
LED Color Status Description
Power Green On The switch is powered.
O The switch is unpowered.
Check the DC power
supply to ensure proper
connection to the outlet
and switch.
Link/
Activity
Green On The switch is connected
to an Ethernet device.
Blinking The switch is
transmitting/receiving
data packets.
O Indicates the port is
not connected to an
Ethernet device.

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1005
to Ethernet devices as shown below. Luxul recommends
Category-5, super Category-5 or Category-6 unshielded
twisted pair (CAT5/CAT5e/CAT6 UTP). To ensure best
performance and stable data transmission at 1000 Mbps,
use Category-6 shielded twisted pair.
Connecting the XGS-1005 to a Device
When a device is properly connected, the Link/Activity
LED for the port to which the device is connected lights
up green. Please refer to the section on LED Indicators
for definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports,
Luxul recommends connecting LAN devices to the
XGS-1005, then connecting the switch to a router LAN
port or another switch as shown in the illustration.
Internet
Connecting the XGS-1005 to a Router or Switch
When the XGS-1005 is properly connected to a router
or switch, the Link/Activity LED for the appropriate port
lights up green. Refer to the section on LED Indicators for
definitions and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1005 includes five Link/
Activity LEDs and one Power LED. For more information
on these LEDs, refer to the table describing these
indicators in the next section.
XGS-1005 Front Panel View
XGS-1005 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1005 include one Power
indicator and 5 Link/Activity indicators. These LED
indicators show the operating status of the XGS-1005
and each switch connection.
The following chart shows the LED indicators of the
XGS-1005 along with a description of each indicator:
LED Color Status Description
Power Green On The switch is powered.
O The switch is unpowered.
Check the DC power
supply to ensure proper
connection to the outlet
and switch.
Link/
Activity
Green On The switch is connected
to an Ethernet device.
Blinking The switch is
transmitting/receiving
data packets.
O Indicates the port is
not connected to an
Ethernet device.

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1005
to Ethernet devices as shown below. Luxul recommends
Category-5, super Category-5 or Category-6 unshielded
twisted pair (CAT5/CAT5e/CAT6 UTP). To ensure best
performance and stable data transmission at 1000 Mbps,
use Category-6 shielded twisted pair.
Connecting the XGS-1005 to a Device
When a device is properly connected, the Link/Activity
LED for the port to which the device is connected lights
up green. Please refer to the section on LED Indicators
for definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports,
Luxul recommends connecting LAN devices to the
XGS-1005, then connecting the switch to a router LAN
port or another switch as shown in the illustration.
Internet
Connecting the XGS-1005 to a Router or Switch
When the XGS-1005 is properly connected to a router
or switch, the Link/Activity LED for the appropriate port
lights up green. Refer to the section on LED Indicators for
definitions and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1005 includes five Link/
Activity LEDs and one Power LED. For more information
on these LEDs, refer to the table describing these
indicators in the next section.
XGS-1005 Front Panel View
XGS-1005 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1005 include one Power
indicator and 5 Link/Activity indicators. These LED
indicators show the operating status of the XGS-1005
and each switch connection.
The following chart shows the LED indicators of the
XGS-1005 along with a description of each indicator:
LED Color Status Description
Power Green On The switch is powered.
O The switch is unpowered.
Check the DC power
supply to ensure proper
connection to the outlet
and switch.
Link/
Activity
Green On The switch is connected
to an Ethernet device.
Blinking The switch is
transmitting/receiving
data packets.
O Indicates the port is
not connected to an
Ethernet device.

Fold Fold Fold
READ ME FIRST
QUICK
INSTALL
GUIDE
5-Port Gigabit Switch
XGS-1005
Includes:
XGS-1005 5-Port Gigabit Switch
Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1005 in a stable/safe place to avoid any
possible damage. Avoid placement in direct sunlight and
do not place heavy articles on the XGS-1005.
Ensure there is adequate space for proper heat dissipa-
tion and ventilation around the switch.
XGS-1005 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet
near the XGS-1005, then connect the power adapter plug
to the switch power connector.
XGS-1005 Rear Panel Detail View
cCAUTION: Use only the included power supply.
If a dierent power supply is used, it
could damage the XGS-1005.
LUX-QIG-XGS-1005-v3 0321703
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any pur-
poses without permission in writing from Luxul. The material in this document
is subject to change without notice. Luxul reserves the right to make changes
to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual
property rights. An implied license only exists for equipment, circuits and
subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the
Luxul logo mark and Simply Connected are all trademarks and or registered
trademarks of Luxul Wireless, Inc. All other trademarks and registered
trademarks are property of their respective holders.
Sales
P: 801-822-5450
E: [email protected]om
Technical Support
P: 801-822-5450 Option 3
E: [email protected]