Luxul XMS-1008P User manual

Simply Connected
Quick Install Guide
XMS-1008P
Gigabit Ethernet Smart POE Switch
Use the XMS-1008P to:
Combine the Benefi ts of POE with Gigabit Technology
(10X Performance of Fast Ethernet)
Simplify POE Device Installation, While Enhancing
Network Performance
Provide Intuitive Network Management and
Optimization Capabilities
Optimize and Protect Your Network with Advanced VLAN,
QoS and Network Security Features

Quick Install Guide
XMS-1008P
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XMS-1008P 093140920
2
Quick Install Guide
Model Number: XMS-1008P
Gigabit Ethernet Smart PoE Switch
© 2014 Luxul. All Rights Reserved.
No part of this publication may be modified or adapted in any way, for any purposes
without permission in writing from Luxul. The material in this manual is subject to change
without notice. Luxul reserves the right to make changes to any product to improve reliability,
function, or design. No license is granted, either expressly or by implication or otherwise
under any Luxul intellectual property rights. An implied license only exists for equipment,
circuits and subsystems contained in this or any Luxul product.
DOCUMENT CONVENTIONS
The following graphical alerts are used in this document to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING!: Indicates a condition or procedure that could result in
personal injury or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CONTACT LUXUL
Sales
P: 801-822-5450
E: [email protected]
Technical Support
P: 801-822-5450
E: suppor[email protected]
PACKAGE CONTENTS
XMS-1008P Gigabit Ethernet Smart POE Switch
Power cable
Two L-shape brackets and eight matched screws

Simply Connected
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners 3
Four rubber footpads
Quick Install Guide
If any of the listed items are missing or damaged, please contact the reseller from whom you
purchased for return/replacement.
HARDWARE DESCRIPTION
Front Panel
The front panel of the XMS-1008P switch includes 8 1000Mbps RJ45 and 2 SFP expansion
ports on the right side and LED indicators on the left side. Each 1000Mbps port has one
Link/Activity LED, one 1000Mbps LED and one POE LED, there are also two SFP LEDs, one
Power LED, one System LED and a reset button.
XMS-1008P Front Panel
Status indicators
Each port has one Link/Activity LED, one 1000Mbps LED and one POE LED. In addition, there
are two SFP LEDs, one Power LED, one System LED, as well as a Reset button to reboot the
device or restore factory default settings. The green LED indicators show the working status
of the switch. The following table describes the LED functionality:

Quick Install Guide
XMS-1008P
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XMS-1008P 093140920
4
Indicator Name Description
Power On Indicates that there is power to the XMS-1008P
Off If LED is off, check power connections and on/off
switch at the back of the unit.
Link/Act On There is a device connected to the port.
Flashing A port is receiving or transmitting data.
Off There is nothing connected to the port.
1000 Mbps On A device capable of 1000Mbps is connected to the port.
Off If a port has no device connected or it is not a 1000
Mbps capable device, the 1000 Mbps LED will be off.
POE On A POE enabled device is connected and being
supplied power
Off No POE enabled device is connected or POE is not
enabled on this port
SYS On Indicates that the XMS-1008P is running normally.
Flashing The XMS-1008P is restoring default settings.
Off The XMS-1008P is in startup and initialization process
or is not on.
At startup, port LEDs will flash for 1 second as a self test.
Reset Button
The Reset button (Located at the lower left corner of the front panel) is used to clear the
current settings of the switch and restore factory default settings.
How to Use the Reset Button
To Hard Reset the Switch: With the XMS-1008P powered on, press the Reset button.
CAUTION: DO NOT hold the button as this will factory default
the switch
To Restore the Default Settings: With the XMS-1008P powered on, press and hold the Reset
button until the status of the System LED shows the following: On – flashing – off. You can now
release the Reset button, and the switch automatically restores the factory default settings.
When the System LED comes on again, the XMS-1008P will be set to factory defaults.
CAUTION: Please note this will remove any configuration done to the switch
prior to Reset.

Simply Connected
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners 5
Network Ports
There are 8 10/100/1000Mbps RJ-45 ports (Ports 1~8), that support Auto MDI/MDIX.
Two Gigabit SFP optical/copper module expansion ports with support for hot-swapping of the
SFP modules.
NOTE: The SFP expansion ports cannot support optical connections until
equipped with an SFP (Mini GBIC) optical module.
NOTE:
When powering up, the port LEDs corresponding to the optical
interface may take a moment to initialize. This is normal as the
XMS-1008P does not detect the optical connection until after the
initialization and startup of internal software systems are completed.
NOTE: To extend your wired network connections beyond 300 feet, an optical
connection will be required. Please contact your Luxul representative or
go to our website to learn more about optical fiber, SFP optical modules
and optical network installation.
Rear Panel
The rear panel provides an AC input socket and power on/off switch. Use the included
power cable to connect the XMS-1008P to a surge protected outlet. The built-in high-
performance switching power supply of the XMS-1008P supports an input range of: AC 100 V
~ 220V, 50 Hz ~ 60 HZ.
INSTALLATION PREPARATION
System and Environmental Requirements
Network cables to connect the XMS-1008P to Ethernet enabled devices
A computer supporting TCP/IP and equipped with a Web browser. Supported Web browser
versions include Microsoft IE 7.0 and up, Safari 1.0 and up or Mozilla Firefox 1.0 and up. The Web
browser is used to configure the XMS-1008P.
Power must be AC 100V ~ 220V, 50Hz ~ 60Hz.
Temperature of the operating environment should be: 32F~113F (0C~45C). Place the switch away
from heat generating devices. For best performance and heat dissipation/ventilation, make sure
there is adequate space around the switch.
Humidity of the operating environment should be: 5%-95% non-condensing. Do not place the
switch in an extremely dirty or damp location.
Keep the switch away from strong electromagnetic fields (i.e. Air Conditioner compressors, fluores-
cent light ballasts, CRT monitors/televisions, etc.), and free from vibration, dust and direct sun light.

Quick Install Guide
XMS-1008P
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XMS-1008P 093140920
6
3.2 Before Connecting to the Network
The XMS-1008P can be rack-mounted or used as a desktop switch. Before connecting to the
network, please be aware of the following requirements:
Install the XMS-1008P in a stable/safe place to avoid any possible damage
Make sure there is adequate space around the XMS-1008P for adequate ventilation and proper
heat dissipation. It is recommended to have at least 4-6 inches around all sides.
Do not place heavy articles on the XMS-1008P.
Power outlets should be within 5 feet of the XMS-1008P.
Verify the ground connection of the outlet is functioning properly.
Check the power cord to confirm a secure connection.
Avoid placement in direct sunlight.
When installing the XMS-1008P on a flat surface, attach the rubber feet to the bottom of the
device to avoid scratching the surface.
XMS-1008P INSTALLATION
Installation on Desktop/Shelf
As shown below, attach the four rubber footpads to 4 corner indentations on the bottom of
the XMS-1008P. Place the switch horizontally on a solid, level platform.
Desktop/Shelf Installation of XMS-1008P
Installation in a Rack
The XMS-1008P is suitable for 19-inch rack installation. With the included L brackets, it can
be conveniently installed into a server or audio rack. As shown below, use three screws
to attach the L-shaped brackets on either sides of the XMS-1008P, and horizontally insert
the switch into a free space within the rack. Use your desired hardware to affix the switch
supports to the rack.
L-Shaped Supports for XMS-1008P

Simply Connected
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners 7
Network Connections
The XMS-1008P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/full-duplex mode
and 1000 Mbps full-duplex mode. All RJ-45 ports support Auto MDI/MDIX and can be used
as ordinary ports or as Uplink ports. Any RJ-45 port can be used to connect the XMS-1008P
to an Ethernet enabled device (including servers, routers, and other switches) without a
crossover cable.
The XMS-1008P offers 2 SFP optical/copper module expansion ports. When Gigabit SFP
optical modules are inserted, these interfaces can support optical fiber cables to extend
the Gigabit network up to 49 miles—enabling the network to extend beyond the 300 foot
limitation of twisted pair Ethernet. When Gigabit SFP copper modules are inserted, the
standard Ethernet limitations apply.
Network Transmission Media
For the RJ-45 ports, Category-5, super Category-5 or Category-6 unshielded twisted
pair (CAT5/CAT5e/CAT6 UTP) should be used. For best results, it is recommended that
Category-6 shielded twisted pair be used to ensure stable data transmission at 1000 Mbps.
Optical fiber/cable should be selected based on the wavelength of the SFP optical module
to be used.
CAUTION: Make sure only one Uplink channel exists between switches or
between the XMS-1008P and a router. Otherwise, loops can occur
and result in network failure.
CONFIGURATION
Login
The XMS-1008P is not equipped with internal DHCP server. However, if you are connecting
to the XBR-2300 Enterprise Dual-WAN Router with the default LAN address, the configura-
tion will be automatic. Otherwise, the IP address of the computer for login and configura-
tion will need to be manually configured. The table below lists the default parameters of the
XMS-1008P.
Parameter: Default Value
Default IP address: 192.168.0.3
Default user name: admin
Default password: admin
Login to the switch with the following steps:
1. Plug an Ethernet cable into any of the switch ports
2. Plug the other end into the Ethernet port of your computer

Information on this document supersedes all previous versions. Products and documents
subject to change without notice. Products may be discontinued without notice.
LUX-QIG-XMS-1008P
093140920
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685
luxul.com | 801-822-5450
3. Power on the switch.
4. Check to see that the IP address of the computer is within this network segment: 192.168.0.xxx
(“xxx” ranges 2~254. For example, 192.168.0.50). For IP address settings, refer to Appendix 2.
5. Open the Web browser and enter 192.168.0.3. The switch
login window appears, as shown at the right.
6. Enter the user name and password (default user name
and default password are both set as “admin”), and then
click “OK” to login to the switch configuration window.
Click any menu item on the left to view and/or modify the
corresponding settings or functions.
ADVANCED SETTINGS
For login and advanced settings information see the User Guide on luxul.com
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment uses and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions may cause harmful
interference to radio communications. However; there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020, declares that
this Luxul XAP-1500 is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
For a copy of this report send a self addressed stamped envelope to:
Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.