M Design LUNA HC Series User manual

COLLECTION LUNA HC
INSTRUCTION FOR INSTALLATION AND USE

2
Attention : THE SUPPLIER TAKES NO RESPONSIBILITY FOR ANY POSSIBLE DAMAGE, POWER LESS
WORKING APPLIANCES DUE TO ACCIDENT AS A RESULT OF INCORRECT INSTALLATION.
SUMMARY
1GENERAL.................................................................................................................................................. 3
1.1 TRANSPORT AND INSTALLATION ........................................................................................................... 3
1.2FUEL ....................................................................................................................................................... 3
1.2.1 Recommended fuel: Wood –hard, soft –damp cca 16%.................................................................. 3
1.2.1.1 Optimal operation .................................................................................................................................... 3
1.2.2 Forbidden fuel ................................................................................................................................... 3
1.3 STARTING THE FIRE ................................................................................................................................ 4
2INSTALLATION ......................................................................................................................................... 4
2.1 INSTALLATION........................................................................................................................................ 4
2.2 LIST OF STANDARDS TO BE OBSERVED DURING ASSEMBLY AND OPERATIONS ..................................... 4
2.3 SAFE DISTANCE FIREPLACE STOVES TYPE „LUNA HC“ FROM FLAMMABLE MATERIALS, LOCATION
FIREPLACE STOVES AND SMOKE EXTRACT............................................................................................. 4
2.4 LOCATION THE FIREPLACE FURNACE TYPE SERIES „LUNA HC“ ON THE FLOOR...................................... 5
2.5 REQUIREMENTS FOR PASSING COMBUSTION AIS ................................................................................. 5
2.6 INSTALLATON THE FIREPLACE MODEL SERIES „LUNA HC“ ON THE PLACE OF USE................... 5
2.7 LOCATION FIREPLACE FURNACE ............................................................................................................ 6
2.8ISOLATION AND SURROUND.................................................................................................................. 6
2.9 INSTALLATION OF 3-SIDED FRAME......................................................................................................... 7
2.10 COMBUSTION AIR INTAKES.................................................................................................................... 7
2.11 VENTILATION ......................................................................................................................................... 7
2.11.1 Natural convection........................................................................................................................ 7
2.11.2 The hot-air distribution ................................................................................................................. 8
2.12 CHIMNEY................................................................................................................................................ 9
3CONTROL ............................................................................................................................................... 10
4GENERAL RECOMMENDATIONS ............................................................................................................. 11
4.1 MAINTANCE......................................................................................................................................... 11
4.1.1 CLEANING GLASS ............................................................................................................................. 12
5SECURITY CONDITIONS .......................................................................................................................... 12
6SUPLIED ACCESSORIES ........................................................................................................................... 13
7SIGN....................................................................................................................................................... 13
8SERIE - SIZE........................................................................................................................................... 14
9SPARE PARTS –LUNA HC........................................................................................................................ 15
10 GUARANTEE........................................................................................................................................... 19
10.1 TERMS AND ITEMS COVERED .............................................................................................................. 19
10.2 GUARRANTY CONDITIONS ................................................................................................................... 19

3
Obr.2c
Obr.2c
1GENERAL
1.1 TRANSPORT AND INSTALLATION
The LUNA is transported in a horizontal position or if there are some problems –in angle-wise 45°.
To make transport easier you can use a set of solid rubber belts.
Before the installation is important to unlock /put out/ transport plug. Plug is placed behind covers on
face sheet.
Promotion of unlocking: Unscrew the cover 1. a 2. /pic. 1a/
Behind screws are placed plugs which is necessary to pull out towards you /see pic 1b, 1c/
After pulling out the plugs is essential to screw on covers back on primary place.
Before installation of the furnace, please check lifting door- lifting up and down and opening
/pic.2a,2b,2c./
1.2 FUEL
1.2.1 Recommended fuel: Wood –hard, soft –damp cca 16%
The quality of the wood is extremely important for the optimal function of the stove /output, clear
glass, etc.../. The ideal is to use dried wood with moisture content 12% to 18%. Damp wood gives off less
heat, clogs the chimmey and the glass of the fireplace´s door. You can also use briquettes and it is better to
use them in combination with wood. Damage as a result of excessive temerature is not under guarantee, two
halves of woods of the 2kg weight are equal 5-7kW.
1.2.1.1 Optimal operation
Optimal use of fuel and optimal operation of the stove reach loading cca 3,5kg of the wood
(3pieces cca 33cm long), lying horizontal on the raft in the middle of the combustion room. The
chimney effect 12Pa and the regulator supply air on maximum.
1.2.2 Forbidden fuel
The use of treated wood /painted, etc./ and all types of household waste, which can disperse hazardous
gases, is FORBIDDEN and CANCELS OUT ANY CLAIM ON THE GUARANTEE. The use of fluid fuel
/petrol, etc./ is also forbidden.
pic.2a
pic.2b
open
close
pic.2c
pic.1b
pic.1c
pic.1a
cover1
cover2

4
1.3 STARTING THE FIRE
Regulation at maximum /see pic.14/
Open the door /pic.2a /.
Put a bed of tinder(paper or firelighters) with a little kindling (small twigs or pieces of wood) in the
stove and light the tinder. Let the door a little open /+3cm/, so as chimney effect arose, which helps the
kindling start the fire.
After the kindling has cought fire and burns well, the logs maybe placed on the fire. When the logs are
burning, the door can be closed.
NOTE: When a fire is made for the first time, the paint will harden and that give off smoke and a smell,
which starts after the fire has bourned for about 10 minutes and lasts for about 15 minutes. See to it that
there is ample ventilation in the room. The combustion chamber should be kept closed except for fuelling
to prevent entry of gases into the room.
CAUTION:
It is not necesarry to overload the fireplace with wood. 1kg dried wood gices a 4kW power.
Example: a fireplace with 80% return gives a power for about 3,2kW for 1kg dry wood. If you want
a power about 6-7kW, it is just enough to put 2kg wood in the fireplace. This is like two normal pieces of
wood. We are not responsible for the wrong use of fireplace and any consequence for not following this
guideline. External surfaces of the stove are hot during operation, which has to be paid due attention to
avoid an accident burns.
2INSTALLATION
2.1 INSTALLATION
For your own safety and satisfaction, we advise you to entrust specialist with the installation. The appliance has
to be installed according to certain prescribes rules and local regulations. The device must be built in an
area with an adequate capacity,on on the board, which can spread the weight of the device. The device must be
positioned so as to maintain the safety distance from any flammable materials that could not fire. However, if
you decide to carry out the work on your own, we advise you to do the following:
Refer to the terms and conditions of our contract of guarantee
Ask your supplier for advice.
2.2 LIST OF STANDARDS TO BE OBSERVED DURING ASSEMBLY AND
OPERATIONS
The fireplace type „LUNA HC“ complies with STN EN 13229. For installation and operation of the
fireplace type „LUNA HC“ should proceed in accordance with STN 92 0300 „Local fire safety appliances
and heat sources“ and STN 73 4201 „The design of chimneys and flues“.
2.3 SAFE DISTANCE FIREPLACE STOVES TYPE „LUNA HC“ FROM FLAMMABLE
MATERIALS, LOCATION FIREPLACE STOVES AND SMOKE EXTRACT
Fireplace type series „LUNA HC“ must be installed in accordance with Decree MV SR No. 95/2004
statute, coll establishing specifications and requirements for fire safety during instalations and operation of
heating appliances, electrothermal appliances and central heating installations and the constructions and use
of chimneys and flues. I tis also necessary to respect the STN 73 4210 „Running of the chimneys and flues
and connecting fuel appliances.“ The manufactorer recommends the installattion of the fireplace furnace
type series „LUNA HC“ conducted by qualified Professional who is responsible for the material used for
installation. The manufactorer is responsible for the delivered product.
When installing the fireplace type series „LUNA HC“ must be complied with 1000 mm safety clearance
from combustible materials.

5
The fireplace type series „LUNA HC“ must be installed so that before it left space on the layout, about 1 x
1 m.
Basis respectively base under fireplace type series „LUNA HC“ must be straight fire material and must
withstand heat stress. Also, wall and ceiling material, which the fireplace type series „LUNA HC“ may not
be from combustible materials, respectively should be used for good thermal insulation
Combustion pipe must be fitted to the fireplace chimney`s mounthpiece furnace type series „LUNA HC“ so
that i tis firmly and tightly connected.
The combustion pipe might be of black respectively stainless steel pipes and elbows. The flue connection must
be made by the shortest route to the flue by STN 73 4210. The combustion pipe should be implemented and
concolidate in order to be released accidentally or spontaneously. Pipes that are plugged into each other, should
be inserted in the direction of flow of exhaust gases. Where the flue passes through building structure, which
contains flammable materials, or surface modified flammable materials should be insulated to protect the
crossing design and implement in accordance with Decree MV SR No. 95/2004 statute.
Connection the combustion pipe of the furnace type series „LUNA HC“ can only be the chimney, which has
been expertly tested. Based on expert examination of the appliance flue connection and issue a professionally
qualified person „Certificate examination on implementation of the chimney, where a professionally qualified
person to deliver state of the chimney and flue for their safe and reliable operation.
2.4 LOCATION THE FIREPLACE FURNACE TYPE SERIES „LUNA HC“ ON THE
FLOOR
In the place of installation fireplace insert type series „LUNA HC“ on the floor must be ensured a minimum
floor load 1000 kg.m-2. The floor before the fireplace insert type series„LUNA HC“must be fire-resistant
material at a distance of at least 1000 mm from front wall of the fireplace isert type series „LUNA HC“.
2.5 REQUIREMENTS FOR PASSING COMBUSTION AIS
The fireplace furnace type series „LUNA HC“can be placed directly in the heated respectively outside
the heated space. The combustion of fuel used air from the area where is the fireplace furnace, or it is possible to
transport external admission of air and connect it according to the point 2.10. In case of insufficient ventilation
of this area is necessary to ensure sefficient fresh air.
2.6 INSTALLATON THE FIREPLACE MODEL SERIES „LUNA HC“ ON THE PLACE
OF USE
Fireplace type series "LUNA HC" is installed in the heated or outside of heated space.
For the location of the fireplace insert type series "LUNA HC" in the heated space, the operator must decide
whether to implement the distribution of heated air or not. If the operator decides that yes, it is necessary to
ensure the distribution of heated air from the space garnishment fireplace insert type series "LUNA HC" by flex-
tube respectively. through appropriate pipes for the heated air inlet temperature of 150 ° C to the desired
location. If the operator decides that no heated air is to be exported from the area Converted fireplace insert with
a hot air diffusers, in order to ensure air circulation.

6
2.7 LOCATION FIREPLACE FURNACE
FIREPLACE INSERT SHOULD NOT BE LAID ON THE FLOOR DUE TO THE NATURAL FLOW
OF AIR.
AIR-INTAKE OPEN IS LOCATED AT THE REAR OF FIREPLACE FURNACE./PIC. 3A/
Setting up the fireplace insert can be in two ways:
Fine-tuning using screws /pic.3b/.
Minimum height from the floor to bottom of the fireplace furnace
3,5cm .
The height from floor A=170mm
2.8 ISOLATION AND SURROUND
FOLLOW THESE INSTRUCTIONS. IF YOU DO NOT FOLLOW THE INSTRUCTIONS QUIPMENT
MAY OVERHEAT.
Once installation is omplete, the device may be doing the surround. If you check everything you can to make a
final insulating and finishing operations. Make sure the device is not put too tight and that there is adequate
space for the flow of hot air. We suggest that you use for insulation insulating plates M-Design. You are advised
to use other insulating materials. Flammable materials are also prohibited.
A very important point when installing the distance which must be between fireplaces and building materials
such as marble.../pic.4a bad version / and / pic.4b good design /.
Pic.3a
Pic.4a
min.5mm
Pic.4b
Pic.3b
A

7
2.9 INSTALLATION OF 3-SIDED FRAME
- 3-sided frame is part of the fireplace furnace type series „Luna HC“..č.5a
- Assembly and disassembly of teh frame by screwing and unscrewing convert screws/pic.5a,5b,5c/. It
should remove the side rails first. The top part is necessary for the authorization hold the screws to avoid
damaging the glass.
.č.5a
PLEASE, ATTENTION TO PRESERVING APPROXIMATELY 2-3 MM CLEARANCE BETWEEN
THE FRAME AND THE MATERIALS FOR SURROUNDING
(HEAT = EXPANSION)
Example:
The total size of the LUNA 900HC is 474 x 888 mm
The thickness of 3-sided frame is 4 mm
The calculation is following: 888 + 2x4mm (3-sided frame) + 2x2mm (expansion) = 900 mm.
For this measurement using a 3-sided frame in combination with marble or other materilas.
Height is measured from the bottom bar on the top 3-sided frame. This is 474mm. Thus 474mm + 2mm.
2.10 COMBUSTION AIR INTAKES
Any type of combustion using air. If enclosure is an additional air supply is very important. It is very important
always to avoid creating negative pressure inside the room. Need air intake with a diameter of 150 mm coming
from outside or ventilated place. The air supply can be connected to Luna HC DC / see pic.3/.On the hole, attach
the mouthpiece / see pic.6 and 7 /. This new system is the air that is required to burn completely separated from
the airflow in the room.
2.11 VENTILATION
2.11.1 Natural convection
It must be open at least two of the three holes for warm air at the top of the fireplace furnace/Pic.8 /.
Openings for air supply are in the bottom of the rear / Pic.7 /. Fireplace should be located at least 20 mm above
the floor / when it is placed on the floor / so as to permit the bottom of the natural flow of air. For a sufficient
circulation of heated air must be ensured that surround the bottom opening with at least 4dm2, excluding dust
filter, including filter or 6dm2.
Pic.5a
Pic.5b
Pic.5c
Pic.7
Pic.6
Obr.č.8
Pic.8

8
2.11.2 The hot-air distribution
The heat-insulated pipes are essential for optimal functioning of the device. (Causing air flow - move) Using a
larger number of tubes (minimum 2) is better traction and noise caused by a stroke is reduced. The installation of
these tubes is best to keep them upright for at least one meter up then change direction, rather do a wide bend
and the exhaust grille with less resistance to air flow, because the lower velocity means lower efficiency heat
register. We recommend that you use the exhaust grille M-design, which have many advantages / obr.11, 12 /.
NOTE: The circulation of hot air is required to be in the room does not produce any vacuum. Grid in the
floor sucking cold air/pic.12/. Do not connect it through a tube. The air itself will find a way to get to the
right place. If it is possible to mount all the accessories you use the same shape and angles, otherwise it
may happen that a grid can make much more heat than others. The hot-air distribution work on a similar
principle as the chimney, one that is warm as the first, the biggest move, and therefore becomes warm
much faster. Grills should be placed so as not to be blocked.
The exhaust grille Pic.11 by providing two connections. To simplify installation, you can use the angle profile,
which is bundled to the grid. This profile is mounted on the inside of the exhaust grille.
INDUCTION
GRID
S=2dm2
Pic.12
Pic.11
EXHAUST GRID
MRIEŽKA
INDUCTION GRID
S=4dm2

9
2.12 CHIMNEY
The design of the chimney must meet strict conditions:
• The chimney must be insulated
• One stack may have more than two changes of direction. The angle of this change of direction must be
greater than 30 ° - 45 ° from the vertical direction
• must be taken into consideration the existing barriers in the vicinity of the hole in the chimney
• The Do not stack more than one fireplace. Use unused seals.
All fireplaces are standard LUNA HC chimney hole diameter 200 mm. Some chimneys may require a different
standard diameters. In this case, refer to the table for the height of the chimney and by reducing the possibility of
reduction. Chimney fireplace insert LUNA HC can connect from the top / Pic.13a / or the back side / Pic.13b /.
The closed door is a slow, directed the flow of gases into the chimney. Short-circuiting valve opens and
closes the doors. Fireplace Luna HC still has two flaps which are not related to the fire but the flow between the
heater jacket and chamber. These valves are located in the rear of the fireplace insert of the air supply and / or
above the upper beam in the front door. These two valves are also controlled the doors (see Pic. 16).
Pic.13b
Pic.13a
Short-circuitingclapper
Clapper2
Clapper 3
Pic.16

10
3CONTROL
Control the fireplace furnace Luna HC driver controls the front bar/see pic.14a /by help of key/pic.14b/. By
controllin the flow of air to control your heater /secondary,primary/, /pic.15/. Open the door control doees
not affect the combustion.
Obr.3a
Obr.3d
Pic.14b
Pic.14a
min
max
Regulation clapper
Way of
exhaust gas
Pic.15

11
4GENERAL RECOMMENDATIONS
The device must be connected and tested before there is doing the surround. To make sure the equipment is
working optimally, they must be cured with tubes isolated. They must meet the minimum diameter of the tube
with hot air / flue / a diameter of a heat. Do not place flammable materials in close proximity to the fireplace
insert. Note: If you leave the door open, a small piece of burning wood / carbon / may fall to the floor. Insulation
materials: it is preferable to use high temperature resistant materials. It is very advantageous position to connect
the chimney and fireplace so that no moisture or water do not get inside. Moisture and water can cause skamolex
swells and then bursts when the fire start.
4.1 MAINTANCE
in addition to regular cleaning of glass, must be your chimney at least once a year sweep to insert
optimal function. / It's not just a legal requirement, but it also makes sense for your own safety /.
Refractory bricks / babble / may still work perfectly, even if they are cracked. However, if the missing
pieces of bricks, bricks must be replaced in order to effectively protect the combustion chamber.
To remove the ash residue can to use the ash / ash /
Cleaning the flue gas flow routes easily convert –lean out the heat-bridge 1 towards you / look out from
behind the bridge, the founder ash / Convert .This cleaning do at least once a month during the heating
season. In the case of rough may be clogging the roads flue can result in poor combustion and excessive
fumigation. Pic.17 / 17a.
Säuberung
Abb.17a
Fallende Aschel
Way of lean out the bridge
Pic.17
Bridge 1

12
4.1.1 CLEANING GLASS
Close the door / pic.2a./
Secure the door in position for cleaning glass. /pic.2b./ ( mae sure that the bottom edge of the glass is
about 1,5 cm above the lower ledge and whether the track sliding door is not an obstacle!)
Slide the door towards the front /see pic.2c/
You can then clean the glass
We recomment the cleaning product that you can use the M-design „Bio – Clean“, which is available
from your suplier. This is one of the few products that does not damage paint.
If you use the fireplace often, it should be lightly brushed with a mechanism for keping the door stabile
silicone oil. Do not use any other types of lubrication or oil. This lubrication is non-stick bace and is
also available from dealers M-design. The mechanism may otherwise be dry and slider door locks.
5SECURITY CONDITIONS
In operating the fireplace furnace type series "LUNA" should observe the following precautions:
The fireplace furnace type series "LUNA" can serve only an adult.
At a distance of 1000 mm before the fireplace furnace type series "LUNA" will not place flammable
objects and materials.
The Fireplace type series "LUNA" shall operate under conditions in which a fire or explosion.
Comply with fire regulations of general application.
When operating the fireplace furnace type series "LUNA" rise to the surface of the walls of high
temperature at which it could be burning. It is therefore prohibited during the operation, touch the walls.
When operating the fireplace type stoves Council "LUNA" rise to the surface of high temperature
controls, in which could cause burns. It is therefore necessary drivers to use with gloves or protective.
auxiliary tools that are included fireplace furnace type series "LUNA".
During working the fireplace furnace type series „LUNA“ is forbidden –give the hand to the flow of
heated air of the reason its too high temperature.
Fire in the fireplace furnace type series "LUNA" never extinguish with water.
The space where it is located fireplace type series "LUNA" must be ensured adequate supply of air for
combustion of fuel.
Loading doors must be kept running the fireplace furnace type series "LUNA" always closed except
placing unit in service and refueling.
They are allowed no interference with the fireplace furnace type series "LUNA" that could endanger the
safe operation.
The ignition of fuel in the aggregate is not permitted to use flammable liquids.
In the event of any problems with the operation of the fireplace furnace type series "LUNA" must be
authorized to call the supplier or manufacturer.
In carrying out the fireplace furnace type series "LUNA" fuel use gloves with sufficient protective
property from excessive heat.

13
6SUPLIED ACCESSORIES
door opener 1pc
hub 5 pc
taker of ash 1pc
operating instrctions, guarrantee and certificate of quality and completeness of the product
Warning!!!
The correct and safe operation of the fireplace furnace type series „LUNA“ it is imperative to
observe the operating instructions and installation!!!
7SIGN
Identification of the type of fireplace type „LUNA HC“ is as follows:
-manufacturer: HT design, s.r.o., 01318 Podhorie 71, Slovensko
-type : „LUNA ...... HC “,
-usable power range: 10 kW
-heat flow into the space: 10 kW
-standard : STN EN 13229
-keep operating instructions
-the unit can be connected to a common chimney
-use only recommended fuels
-the appliance is designed for: shor-term operation
-serial number/see Pic.18/
TYPE- fireplace
700 HC
900 HC
1100 HC
Rated thermal power (kW)
9
10
11
Average efficiency (%)
78
78
78
Heat flow into the space (kW)
9
10
11
Power range (kW)
5 - 11
5 - 12
6 - 13
Flue gas temperature at rated output (°C)
195
195
195
Avg. CO concentration at 13% O2
(%)
0,10
0,10
0,10
The average volume concentration of CO at
13% O2 (mg.m-3)
1200
1200
1200
Minimum blast (Pa)
12
12
12
The weight of the fireplace furnace (kg)
280
300
330
Minimum distance from flammable
materials from the flanks and rear of
(mm)
300
300
300
Minimum distance from flammable
materials from the front (mm)
1000
1000
1000
Fuel delivery interval (h)
1
1
1
Recommeded fuel –dry wood
Beech, oak, spruce
Consumption of fuel at usable power range
(kg/h)
3,2
3,5
3,7
123456
Pic.18

14
8SERIE - SIZE

15
9SPARE PARTS –Luna HC

16
SPARE PARTS –Luna HC

17
SPARE PARTS –Luna HC

18

19
10 GUARANTEE
10.1 TERMS AND ITEMS COVERED
7 years` guarantee on the general structure
2 years` guarantee on the parts
No guarantee on glass, seals and lining the combustion chamber
10.2 GUARRANTY CONDITIONS
The claim must be submitted to the warranty, otherwise the claim is recognized.
1. The guarranty covers all defects in the fireplace furnace type series „LUNA“ and parts that are useable
due to poor quality material or faulty processing.
2. The guarranty does not apply to defects resulting non-compliance with the conditions specified in the
instructions for installtion, operation and maintenance or that the unit is used other than in the manner and
for any purpose other than for which i tis intended under normal conditions, poor or improper handling,
eg. Improrer storage, improrer handling, improrer use of fuel.
3. The guarranty does not apply to defects caused by impurities in the fuel combustion gas inappropriate,
improper placement and the inevitable damage caused by the event (natural disaster, etc...)
4. The guarranty also does not apply to damages caused indirectly and damage or personal injury cases.
5. The claims for non-compliance security guarantees expire, the expiry of the guarrantee period, repair or
modification of the fireplace furnace type series „LUNA“ unauthorized person.
6. The costs associated with sending a service worker to put the fireplace furnace type series „LUNA“ not
covered by the guarantee shall be borne by the customer –a user.
7. The liability for defects –a claim the user applies to the production company.
8. Other rights and obligations arising from liability for product defect shall be governed by the provisions of
generally binding legal regulations applicable in the Slovak Republic (Civil Code, Commercial Code,
etc.).
Date of sale .......................
Seller:..................................................
Contact the manufacturer: Contact the seller :
HT-design s.r.o. M-Design
Krásno nad Kysucou Torhoutsesteenweg 222a
02302 SLOVENSKO 8210 Zedelgem
e-mail: [e-mail] Belgium
http:\\www.m-design.be
e-mail: [e-mail]
Your serial number
..................................................