M-system R8-FS16N User manual

R8-FS16N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-9791 P. 1 / 5
DC CURRENT / VOLTAGE INPUT MODULE
(built-in excitation /16points, non-isolated)MODEL R8-FS16N
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, check the
contents of the package you received as below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
DC current / voltage input module......................................(1)
■MODEL NO.
Confirm that the model number described on the product is
exactly what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
•The equipment must be mounted inside a panel.
•The actual installation environments such as panel con-
figurations, connected devices and connected wires may
affect the protection level of this unit when it is integrat-
ed in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure CE conformity.
■GENERAL PRECAUTIONS
•Before you remove or mount the unit, turn off the power
supply and input signal for safety.
•Do not touch the connector while power is on. The unit
may have a malfunction due to static electricity etc.
•Switches on the side of the module can be set for mainte-
nance only while the power supply is off. Do not access
them while the power is supplied.
■ENVIRONMENT
•Indoor use
•When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
•Do not install the unit where it is subjected to continuous
vibration. Do not apply physical impact to the unit.
•Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to90% RH
in order to ensure adequate life span and operation.
■WIRING
•Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
•Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■EXCITATION SUPPLY
•Rated curent 3 A DC (rated current 3 A for internal fuse
(slow blow fuse i2t (A2sec) max. 5.04)
■AND ....
The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for sat-
isfying complete performance described in the data sheet.
INSTALLATION
■HOW TO MOUNT THE MODULE ON DIN RAIL
• I/O Module
A
B
Confirm that the locking clamps of the I/O module are set.
Insert the module in parallel to the next one while aligning
the grooves of both modules (A & B in the above figure).
Maintain it perpendicularly to the rail.
More I/O modules can be added in the same manner.

R8-FS16N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-9791 P. 2 / 5
• Protective Cover
Groove
Hook
The protective cover is to be attached over the connected
I/O module
at the right end.
Align the hooks on the cover with the grooves of the module
and slide it
straight until the hooks are latched.
When removing the cover, pull it out while squeezing the
hooks inward.
■HOW TO UNMOUNT THE MODULE ON DIN RAIL
Release the locking clamps and pull out straight the mod-
ule.
• Removing an intermediate module
Caution !
1 ) Be careful not to hurt your hand by pointed edges of
the internal communication bus connector.
2 ) I/O modules cannot hold tightly on the DIN rail by
themselves without power/network module.
Secure them to the position if necessary by using DIN
rail end plates.

R8-FS16N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-9791 P. 3 / 5
COMPONENT IDENTIFICATION
Function Setting
DIP SW
Input Connector
Voltage / Current
DIP SW
8
7
6
5
4
3
2
1
SW1 SW2
On
■FRONT VIEW ■SIDE VIEW
RUN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
IN
12
39 40
On
1
16
On
1
16
Internal Bus Connector
Status Indicator LED
Input Status Indicator LEDs
Internal Bus Connector
VI
VI
■INDICATOR LED
LED OPERATION FUNCTION
Status OFF Stopping
Green ON Valid host communication
Green Blinking
Reading/writing configuration
Red ON Setting error
Red Blinking Parameter error
Input
Status
OFF Input data in the range
Red Blinking Input data out of range
■PC CONFIGURATOR
The following parameters can be set with using PC Configu-
rator Software (model: R8CFG):
•Input setting by channels (setting value, scaling, zero/
gain adjustments, selecting current/voltage)
•Common setting (loss of internal bus communication de-
tection time)
Programming by the PC Configurator is available via the
Power/Network Module.
Refer to the users manual for the R8CFG for detailed opera-
tion of the software program.
■MODULE ADDRESS
SW 1-1 through 1-4 determine the tenth place digit, while
SW 1-5 through 1-8 do the ones place digit of the address.
Address is selected between 0 to 24.
(Factory setting: 0)
MODULE
ADDRESS
SW1
x10 1234
x1 5 6 7 8
0 OFF OFF OFF OFF
1 OFF OFF OFF ON
2 OFF OFF ON OFF
3 OFF OFF ON ON
4 OFF ON OFF OFF
5 OFF ON OFF ON
6 OFF ON ON OFF
7 OFF ON ON ON
8 ON OFF OFF OFF
9 ON OFF OFF ON
■OPERATING MODE
(*)Factory setting
• Terminator DIP SW
TERMINATOR SW SW2
Without (*) OFF
With ON
Note: SW 2-1 through 2-4 and SW 2-4, 5, 7, 8 are unused. Be sure to set
unused SWs to OFF.
• Voltage / Current DIP SW
For voltage input, set the switch OFF.
For current input set the switch ON.
Note: To configure the input, setting from configurator software and the
setting of this switch are required.

R8-FS16N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-9791 P. 4 / 5
■INPUT CONNECTOR ASSIGNMENT
39 40
12
NO. ID FUNCTION
1In 1 Input 1 (+)
2Input 1 (−)
3In 2 Input 2 (+)
4Input 2 (−)
5In 3 Input 3 (+)
6Input 3 (−)
7In 4 Input 4 (+)
8Input 4 (−)
9In 5 Input 5 (+)
10 Input 5 (−)
11 In 6 Input 6 (+)
12 Input 6 (−)
13 In 7 Input 7 (+)
14 Input 7 (−)
15 In 8 Input 8 (+)
16 Input 8 (−)
17 In 9 Input 9 (+)
18 Input 9 (−)
19 In 10 Input 10 (+)
20 Input 10 (−)
21 In 11 Input 11 (+)
22 Input 11 (−)
23 In 12 Input 12 (+)
24 Input 12 (−)
25 In 13 Input 13 (+)
26 Input 13 (−)
27 In 14 Input 14 (+)
28 Input 14 (−)
29 In 15 Input 15 (+)
30 Input 15 (−)
31 In 16 Input 16 (+)
32 Input 16 (−)
33, 34
35, 36 24V Excitation supply 24V
37, 38
39, 40 0V Excitation supply 0V
CONNECTION DIAGRAM
INTERNAL POWER
INTERNAL BUS
EXC. SUPPLY
1
2
+
−
INPUT 1
3
4
+
−
INPUT 2
5
6
+
−
INPUT 3
7
8
+
−
INPUT 4
9
10
+
−
INPUT 5
11
12
+
−
INPUT 6
13
14
+
−
INPUT 7
15
16
+
−
INPUT 8
17
18
+
−
INPUT 9
19
20
+
−
INPUT 10
21
22
+
−
INPUT 11
23
24
+
−
INPUT 12
25
26
+
−
INPUT 13
27
28
+
−
INPUT 14
29
30
+
−
INPUT 15
31
32
+
−
INPUT 16
33
34
+24V
+24V
35
36
+24V
+24V
37
38
0V
0V
39
40
0V
0V
BUS CONNECTOR

R8-FS16N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-9791 P. 5 / 5
EXTERNAL DIMENSIONS unit: mm (inch)
115(4.53)
6(.24)
7(.28)6(.24)7(.28)
[3(.12)] [4(.16)]
24(.94)[75(2.95)]
55(2.17)
DIN RAIL (35 mm wide)
WIRING INSTRUCTIONS
■MIL connector
PWB connector XG4A-4034 (Omron)
Recommended socket XG5N-401 (Omron)*1
Recommended contact XG5W-0231 (Omron)*1
Applicable wire size: : AWG22, 17 strands, (0.16 dia)
*1) Not included in the package. Refer to the specifications of the product.