M-system M2EXV User manual

M2EXV
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-5133-B Rev1 P. 1 / 18
SIGNAL TRANSMITTER
(PC programmable)MODEL M2EXV
OPERATING MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Signal conditioner (body + base socket).............................(1)
■MODEL NO.
Confirm Model No. marking on the side of the product to be
exactly what you ordered.
■OPERATING MANUAL
This manual describes detailed operation regarding settings.
The M2EXV is programmable using a PC. For detailed in-
formation on the PC configuration, refer to the M2ECFG
users manual (EM-5147).
The M2ECFG Configurator Software is downloadable at
M-System’s web site: http://www.m-system.co.jp
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
•This equipment is suitable for Pollution Degree 2 and In-
stallation Category II. Reinforced insulation (signal in-
put or output to power input: 300V) and basic insulation
(signal input to output: 300V) are maintained. Prior to
installation, check that the insulation class of this unit
satisfies the system requirements.
•Altitude up to 2000 meters.
•The equipment must be mounted inside a panel.
•The equipment must be installed such that appropriate
clearance and creepage distances are maintained to con-
form to CE requirements. Failure to observe these re-
quirements may invalidate the CE conformance.
•The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
•Install lightning surge protectors for those wires connect-
ed to remote locations.
■POWER INPUT RATING & OPERATIONAL RANGE
Locate the power input rating marked on the product and
confirm its operational range as indicated below:
100 – 240V AC rating: 85 – 264V, 47 – 66 Hz,
≤ 4.5VA at 100V AC
≤ 6.5VA at 200V AC
≤ 8.5VA at 264V AC
24V DC rating: 24V ±10%, ≤ 2.3W
110V DC rating: 85 – 150V, ≤ 2.3W
■GENERAL PRECAUTIONS
Before you remove the unit from the socket or mount it,
turn off the power supply and input signal for safety.
■ENVIRONMENT
•Indoor use
•When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
•Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
•Environmental temperature must be within -5 to +55°C
(23 to 131°F) with relative humidity within 10 to 85% RH
in order to ensure adequate life span and operation.
■WIRING
•Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
•Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
•The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
•With voltage output, do not leave the output terminals
shortcircuited for a long time. The unit is designed to en-
dure it without breakdown, however, it may shorten ap-
propriate life duration.
•The edge of the display may be hidden by the frame and
invisible depending on the view angle.
COMPONENT IDENTIFICATION
Connection Diagram
(Side)
Body Base Socket
Display
Fixing Screw
(screw for attaching
the body to the socket)
Mode
Set
Up
Down
Specification

M2EXV
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-5133-B Rev1 P. 2 / 18
INSTALLATION
Loosen the fixing screw in front of the unit in order to separate the body from the base socket.
■FIXING SCREW
The fixing screw can be pushed into the body when it is
not in use. Tighten the knob until the body is securely at-
tached to the base socket. Push it into the body and turn it
clockwise to lock. Push the knob and turn it counterclock-
wise to unlock so that the know pops out.
■
DIN Rail
35mm wide
Spring Loaded
DIN Rail Adaptor
DIN RAIL MOUNTING
Set the base socket so that
its DIN rail adaptor is at
the bottom. Position the
upper hook at the rear side
of base socket on the DIN
rail and push in the lower.
When removing the socket,
push down the DIN rail
adaptor utilizing a minus
screwdriver and pull.
■WALL MOUNTING
Refer to the drawings in
the shown below.
TERMINAL CONNECTIONS
Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.
■EXTERNAL DIMENSIONS unit: mm (inch)
28.5 (1.12)
83 (3.27)
94 (3.70)
8
(.31)
124 (4.88)
22 (.87)
6 (.23)
59 (2.32)
11–M3
SCREW
72 (2.83)
36 (1.42)
29.5 (1.16)
2–4.2x5
(.17x.20)
MTG HOLE
6 (.24) deep
DIN RAIL
35mm wide
[4 (.16)]
• When mounting, no extra space is needed between units.
4
8 7
10
8
(.31)
11
56
123
9
■CONNECTION DIAGRAM
1
4
2
+
–
OUTPUT
7
8
10
11
CONFIGURATOR JACK
U(+)
V(–)
POWER
–
Input Current
+
+
Input Voltage
–

M2EXV
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-5133-B Rev1 P. 3 / 18
EXTERNAL VIEWS
Display
Mode Button
Set Button
Configurator Jack
Up Button
Down Button
Up
Down
Mode
Set
Output Setting DIP SW
ON
1
2
3
4
5
6
7
8
SW1
OFF
ON
1
2
3
4
5
6
7
8
SW1
OFF
PERCENT
100.00
OUTPUT
20.000
%
mA
COMPONENT FUNCTION
Display Indicates present values, setting values and abnormal information. Two types of present values at up-
per and lower are displayed by setting.
Mode button Used to shift from measuring mode to each setting mode. Destination to shift is changed by the time
pressing and holding the button. Used to return from each setting mode to measuring mode. (press and
hold for 2 sec. or more)
Set button Used to change setting value of setting parameter. When at setting changeable state, used to enter
(save) the setting value. Used to move on through digits of setting value for input/output scaling at
setting changeable state,
Up button Used to shift through setting parameter, and to increase or select setting value.
Down button Used to shift through setting parameter, and to decrease or select setting value.
Configurator Jack Used to configure with M2E configurator software (model: M2ECFG). At the same time, set the lockout
setting of the unit to ‘lock’.
DIP SWITCH
The internal DIP switch for output setting is required to select output types before setting a precise output range using front
buttons or setting with a PC.
Refer to the “PROGRAMMING” for the operation with front buttons. Refer to the users manual (EM-5147) of M2E Configurator
Software (model: M2ECFG) for setting with PC.
Output Range SW1
12345678
0– 20mA OFF ON OFF OFF OFF OFF ON OFF
-5– +5V OFF OFF ON OFF ON OFF OFF ON
-10– +10V OFF OFF ON OFF OFF ON OFF ON
CAUTION: DO NOT set DIP switches while power is supplied. Otherwise, the unit may fail.

M2EXV
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-5133-B Rev1 P. 4 / 18
SCREEN DISPLAY
■DISPLAY IN MEASURING MODE
• Double tiered display
The unit can select and display any two items out of input
engineering value, input scaling value, % value*, output en-
gineering value, and output scaling value.
* Percent value for input.
INP (Scaling)
L / min
12.34
50.00
PERCENT
%
Item name
Value
Unit
Item name
Value
Unit
Upper
Lower
• Single tiered display
When displayed item is one, it is available to show big char-
acters in single tiered display.
INPUT
mA
20.00
Value
Unit
Item name
Refer to the Display setting of the Advanced mode for
settings.
■DISPLAY IN EACH SETTING MODE
For each setting, current values of setting parameter, ITEM
number and setting value are indicated. During setting,
‘(Setting)’ is indicated at the side of ‘DATA’ display.
If the power is mistakenly shut down during setting, set-
ting values are discarded. (Return to the value before set-
ting change.) Setting display previously displayed before
power shutdown is indicated at next power up.
Input range
ITEM
11
DATA (Setting)
-10–+10V
Setting parameter
Item number
Setting Value
The long setting parameter is indicated by scrolling.
ITEM
14
DATA
0.00
Indicated by scrolling
0% input scaling
■DISPLAY TIMEOUT
When there is no operation within the setting time of dis-
play timeout, display is turned off. Pressing Mode, Set, Up
or Down button or occurring error enables to return from
display off. Set ‘0’ to display ‘always on’.

M2EXV
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-5133-B Rev1 P. 5 / 18
PROGRAMMING
■SETTING FLOWCHART
POWER ON
Measuring Mode
Hold down Mode button for ≥ 2 seconds
Hold down Mode button
for ≥ 2 seconds
Basic Setting Mode
Option Mode
Advanced Mode
Hold down Mode button for ≥ 2 seconds
Hold down Mode button for ≥ 4 seconds
Hold down Mode button for ≥ 2 seconds
Hold down Mode button for ≥ 6 seconds
Linearization Mode
Hold down Mode button for ≥ 2 seconds
Hold down Mode button for ≥ 8 seconds

M2EXV
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-5133-B Rev1 P. 6 / 18
■OPERATION IN EACH SETTING MODE
• Basic operation
Mode button: In measuring mode, holding down Mode button for ≥ 2 seconds, ≥ 4 seconds, ≥ 6 seconds or ≥ 8 seconds
enables to move on to each setting mode. Holding down Mode button for ≥ 2 seconds at each setting item
display enables to return to measuring mode.
Holding down Mode button for ≥ 2 seconds while changing settings (‘(Setting)’ is displayed next to ‘DATA’)
enables to discard setting value in changing, and to return to the state before change settings (‘(Setting)’
next to ‘DATA’ is off).
Set button: Pressing Set button at each setting parameter enables to blink setting value and changing settings is
ready (‘(Setting)’ is displayed next to ‘DATA’). Pressing Set button while changing settings enables to
save (enter) setting value and change from blinking to on.
Up button: Press Up button to move through setting parameters. Selecting setting value while changing settings,
increasing a setting value to set value. Keeping pressing Up button enables to increase the value
continuously.
Down button: Press Down button to move through setting parameters. Selecting setting value while changing settings,
decreasing a setting value to set value. Keeping pressing Down button enables to decrease the value
continuously.
• Input/ output display scaling setting parameter
For input/output display scaling setting parameter, set values digit by digit. Pressing Set button enables to move blinking
digit. Adjust blinking digit to set numerical value with Up and Down button. Blinking digit moves from most significant digit
with pressing Set button. At least significant digit, pressing Set button again enables to turn on and determine the setting
value. During setting, press and hold Mode button for ≥ 2 seconds to discard the setting value.
ITEM
14
DATA
0
0% input scal
ITEM
14
DATA (Setting)
0% input scal
ITEM
14
DATA (Setting)
0% input scal
ITEM
14
DATA (Setting)
0% input scal
Set button Set button Set button
Setting sixth digit Setting fifth digit
Set button (save)
Setting first digit
000000 000000000000
• Lockout setting
‘Lockout setting’ is available for the unit. When unlocking the lockout setting, indicate ‘Lockout Setting’ of ‘ITEM01’ in each
setting mode and set ‘Unlock’. To enable lockout setting again, set ‘Lock’. Even when lockout setting is enabled, it is avail-
able to confirm the each setting value. ‘DATA (Locked)’ is indicated in that case.

M2EXV
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-5133-B Rev1 P. 7 / 18
■BASIC SETTING MODE
Measuring Mode
Lockout Setting
Input Range
0% Input Setting
100% Input Setting
0% Input Scaling
100% Input Scaling
Input Decimal Point
Output Range
0% Output Setting
100% Output Setting
0% Output Scaling
100% Output Scaling
Output Decimal Point
Loop Test
Set
Set
Hold down Mode button
for ≥ 2 seconds
Hold down Mode button
for ≥ 2 seconds
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
SetSet
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Up Down
Up Down
Up Down
Up Down
Up Down
Up Down
Up Down
Up Down
Up Down
Up Down
Up Down
Up Down
Up Down
Up Down
Lock / Unlock
0 – 50 mA /
-1000 – +1000 mV /
-10 – +10 V
0.00 – 48.00 /
-1000.0 – 900.0 /
-10.000 – 9.000
2.00 – 50.00 /
-900.0 – 1000.0 /
-9.000 – 10.000
-99999 – 999999
-99999 – 999999
oooooo / ooooo.o
oooo.oo / ooo.ooo
oo.oooo / o.ooooo
0 – 20 mA /
-5 – +5 V /
-10 – +10 V
0.000 – 19.000 /
-5.000 – 4.750 /
-10.000 – 9.000
1.000 – 20.000 /
-4.750 – 5.000 /
-9.000 – 10.000
-99999 – 999999
-99999 – 999999
oooooo / ooooo.o
oooo.oo / ooo.ooo
oo.oooo / o.ooooo
Cancel / Set
Basic Setting Mode

M2EXV
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-5133-B Rev1 P. 8 / 18
• Parameters
MODE ITEM SETTING PARAMETER RANGE UNIT INITIAL VALUE
Basic setting 01 Lockout setting Lock / Unlock — Lock
11
Input range 0 – 50mA
-1000 – +1000mV
-10 – +10V
— 0 – 50mA
12
0 % input setting 0.00 – 48.00
-1000.0 – 900.0
-10.000 – 9.000
mA
mV
V
4.00
13
100 % input setting 2.00 – 50.00
-900.0 – 1000.0
-9.000 – 10.000
mA
mV
V
20.00
14 0 % input scaling -99999 – 999999 — 0.00
15 100 % input scaling -99999 – 999999 — 100.00
16
Input decimal point No decimal point
The number of decimal
places : 1 – 5,
— 2 places of decimals
17
Output range 0 – 20mA
-5 – +5V
-10 – +10V
— 0 – 20mA
18
0 % output setting 0.000 – 19.000
-5.000 – 4.750
-10.000 – 9.000
mA
V
V
4.000
19
100 % output setting 1.000 – 20.000
-4.750 – 5.000
-9.000 – 10.000
mA
V
V
20.000
20 0 % output scaling -99999 – 999999 — 0.00
21 100 % output scaling -99999 – 999999 — 100.00
22
Output decimal point No decimal point
The number of decimal
places : 1 – 5,
— 2 places of decimals
26 Loop test -5.00 – 105.00 % Cancel

M2EXV
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-5133-B Rev1 P. 9 / 18
[01] Lockout Setting
Set Lock / Unlock of lockout setting.
SETTING VALUE DESCRIPTION INITIAL VALUE
Lock Lockout setting enable Lock
Unlock Lockout setting disable
Even when setting is ‘Lock’, it is available to move on to
each setting mode and confirm the setting value of each
setting parameter. In each setting parameter display, when
‘Lock’, ‘DATA (Locked)’ is indicated, when ‘Unlock’, ‘DATA’
is indicated.
[11] Input range
Set the type of output signal
SETTING VALUE DESCRIPTION INITIAL VALUE
0 – 50 mA
Input: 0 – 50 mA DC
0 – 50 mA-1000 – +1000 mV Input: -1000 – +1000 mV DC
-10 – +10 V Input: -10 – +10 V DC
When input range is changed, turn the power off,and change
the connection to the input terminal of the unit. Input set-
ting value is changed to initial value.
[12] 0 % input setting
Set the 0 % input setting.
Setting range differs according to input range.
INPUT RANGE SETTING RANGE MIN. SPAN INITIAL VALUE
0 – 50 mA 0.00 – 48.00 2.00 4.00
-1000 – +1000 mV -1000.0 – 900.0 100.0 -1000.0
-10 – +10 V -10.000 – 9.000 1.000 -10.000
Set as follows.
[12] 0 % input setting < [13] 100 % input setting
[13] 100 % input setting
Set the 100 % input setting.
Setting range differs according to input range.
INPUT RANGE SETTING RANGE MIN. SPAN INITIAL VALUE
0 – 50 mA 2.00 – 50.00 2.00 20.00
-1000 – +1000 mV -900.0 – 1000.0 100.0 1000.0
-10 – +10 V -9.000 – 10.000 1.000 10.000
Set as follows.
[12] 0 % input setting < [13] 100 % input setting
[14] 0 % input scaling
Set the display value of 0 % input setting.
SETTING RANGE INITIAL VALUE
-99999 – 999999 0.00
[15] 100 % input scaling
Set the display value of 100 % input setting.
SETTING RANGE INITIAL VALUE
-99999 – 999999 100.00
[16] Input decimal point
Set the decimal point position of [14] 0 % and [15] 100 %
input display scaling.
SETTING VALUE DESCRIPTION INITIAL VALUE
oooooo Decimal point: None
2 places of
decimals
ooooo.o Number of decimal places: 1
oooo.oo Number of decimal places: 2
ooo.ooo Number of decimal places: 3
oo.oooo Number of decimal places: 4
o.ooooo Number of decimal places: 5
[17] Output range
Set the range of output signal of the unit.
SETTING VALUE DESCRIPTION INITIAL VALUE
0 – 20 mA Output: 0 – 20 mA DC
0 – 20 mA-5 – +5 V Output: -5 – +5 V DC
-10 – +10 V Output: -10 – +10 V DC
When output range is changed, turn the power off, and
then set the output setting DIP SW on the side of the unit.
Setting is as follows. Output setting value is changed to ini-
tial value.
OUTPUT
RANGE
SW1
12345678
0 – 20 mA OFF ON OFF OFF OFF OFF ON OFF
-5 – +5 V OFF OFF ON OFF ON OFF OFF ON
-10 – +10 V OFF OFF ON OFF OFF ON OFF ON
[18] 0 % output setting
Set the 0 % output setting.
OUTPUT RANGE SETTING RANGE MIN. SPAN INITIAL VALUE
0 – 20 mA 0.000 – 19.000 1.000 4.000
-5 – +5 V -5.000 – 4.750 0.250 -5.000
-10 – +10 V -10.000 – 9.000 1.000 -10.000
Set as follows.
[18] 0 % output setting < [19] 100 % output setting
The value is indicated by ‘OUTPUT’ at measuring mode.
[19] 100 % output setting
Set the 100 % output setting.
OUTPUT RANGE SETTING RANGE MIN. SPAN INITIAL VALUE
0 – 20 mA 1.000 – 20.000 1.000 20.000
-5 – +5 V -4.750 – 5.000 0.250 5.000
-10 – +10 V -9.000 – 10.000 1.000 10.000
Set as follows.
[18] 0 % output setting < [19] 100 % output setting
The value is indicated by ‘OUTPUT’ at measuring mode.
[20] 0 % output scaling
Set the display value of [18] 0 % output setting.
SETTING RANGE INITIAL VALUE
-99999 – 999999 0.00
[21] 100 % output scaling
Set the display value of [19] 100 % output setting.
SETTING RANGE INITIAL VALUE
-99999 – 999999 100.00

M2EXV
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax:
[phone] E-mail: [e-mail]
EM-5133-B Rev1 P. 10 / 18
[22] Output decimal point
Set decimal point position for [20] 0 % and [21] 100 % output scaling.
SETTING VALUE DESCRIPTION INITIAL VALUE
oooooo Decimal point: None
2 places of
decimals
ooooo.o Number of decimal places: 1
oooo.oo Number of decimal places: 2
ooo.ooo Number of decimal places: 3
oo.oooo Number of decimal places: 4
o.ooooo Number of decimal places: 5
[26] Loop test
As pressing Set button enables to blink ‘Cancel’, changing to ‘Set’ by pressing Up or Down and pressing ‘Set’ allows to indicate
Loop Test display. Present value is indicated. Increase or decrease it by pressing Up and Down button. Press and hold them
enables to change value continuously.*1
Pressing and holding Mode button more than 2 seconds or turning off the power enable to exit loop test.
ITEM
26
Loop test
ITEM
26
DATA (Setting)DATA (Setting)
Loop test Loop test
Up/Down
button Set button
Set
mA
4.000
0.00
% Cancel
Output engineering value
Output % value
*1. While loop test is performing, actual input is disregarded.
While loop test is performing and ‘Display timeout’ is enabled to display off, return to the display on by pressing a front button.