MadgeTech Shock101-5-EB Specification sheet

Shock101-EB
Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289
Battery Warning
WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT SHORT CIRCUIT, CHARGE,
FORCE OVER DISCHARGE, DISASSEMBLE, CRUSH, PENETRATE OR INCINERATE. BATTERY MAY
LEAK OR EXPLODE IF HEATED ABOVE 54 °C (129 °F).
DOC-1064035-00 REV 11 2014.07.07
Shock101-EB-5
Tri-axial +5G, Shock Data Logger with Extended Battery Life
Shock101-EB-50
Tri-axial +50G, Shock Data Logger with Extended Battery Life
Shock101-EB-100
Tri-axial +100G, Shock Data Logger with Extended Battery Life
Shock101-EB-250
Tri-axial +250G, Shock Data Logger with Extended Battery Life
Description Shock101-EB
Channels Shock (3 axes)
Acceleration Range
*See Table BelowAcceleration Resolution
Calibrated Accuracy
Sample Rate 512 Hz
Reading Rate 64 Hz up to 5 minutes
Memory 349,525/axis
Required Interface Package IFC200
Baud Rate 115,200
Typical Battery Life 60 days
Operating Environment -20 °C to +54 °C, 0 to 95%RH (non-condensing)
Material Anodized aluminum
Dimensions 5.5 in x 5.2 in x 3.2 in (140 mm x 132 mm x 80 mm)
Weight 5 lb (2.3 kg)
Approvals CE
*Shock101-EB Acceleration Range, Resolution and Accuracy
Range (g) +5 +50 +100 +250
Accuracy (g) +0.2 +1 +2 +4
Resolution (g) 0.01 0.05 0.1 0.2
Product User Guide
www. .com [e-mail]1.800.561.8187

Product Notes
Reading Intervals
The Shock101-EB samples at 512 Hz and at the user specified reading rate, the device
writes the peak values (g-force) to memory.
For Example:
Axis Orientation
When the Shock101 is laying flat, with the label facing up,
the x-axis indicates left to right direction and will read ~0 g
when still. The y-axis reads in a top to bottom direction and
reads ~0 g when still. The z-axis reads perpendicular to the
other two axis, and will read ~1 g when still.
Installation Guide
Installing the Interface cable
- IFC200
Insert the device into a USB port. The drivers will install automatically.
Device Operation
Connecting and Starting the data logger
- Once the software is installed and running, plug the interface cable into the data logger.
- Connect the USB end of the interface cable into an open USB port on the computer.
- The device will appear in the Connected Devices list, highlight the desired data logger.
- For most applications, select “Custom Start” from the menu bar and choose the desired
start method, reading rate and other parameters appropriate for the data logging
application and click “Start”. (“Quick Start” applies the most recent custom start options,
“Batch Start” is used for managing multiple loggers at once, “Real Time Start” stores the
dataset as it records while connected to the logger.)
Shock101-EB Product User Guide
- The status of the device will change to “Running”, “Waiting to Start” or “Waiting to
Manual Start”, depending upon your start method.
- Disconnect the data logger from the interface cable and place it in the environment to
measure.
Note: The device will stop recording data when the end of memory is reached or the device is stopped. At this point the
device cannot be restarted until it has been re-armed by the computer.
Downloading data from a data logger
- Connect the logger to the interface cable.
- Highlight the data logger in the Connected Devices list. Click “Stop” on the menu bar.
- Once the data logger is stopped, with the logger highlighted, click “Download”. You will
be prompted to name your report.
- Downloading will offload and save all the recorded data to the PC.
Device Maintenance
Battery Replacement
Materials:
3/32” HEX Driver (Allen Key)
Replacement Battery (MN1300)
- Remove the cover from the device by unscrewing the four screws.
- Tip out the battery holder.
Note: Do not pull on the battery leads.
- Replace the 6 D-cell batteries and put the holder back into the device.
- Replace the cover taking care not to pinch the wires. Screw the enclosure back
together securely.
Note: Be sure not to over tighten the screws or strip the threads.
Recalibration
The Shock101-EB standard calibration is performed at 0 g for the x-axis, 0 g for the y-axis
and 1 g for the z-axis.
Sampled Data: Recorded Data:
Y-Axis
Z-Axis
X-Axis
www. .com [e-mail]1.800.561.8187