Makita DPB184 User manual

DPB184
EN Cordless Portable Band Saw INSTRUCTION MANUAL 5
ZHCN 充电式轻便带锯 使用说明书 12
ID Mesin Gergaji Pita Portabel
Tanpa Kabel PETUNJUK PENGGUNAAN 20
MS Gergaji Gelung Mudah alih
Tanpa Kord MANUAL ARAHAN 28
VI Máy Cưa Vòng Cầm Tay Hoạt
Động Bằng Pin TÀI LIỆU HƯỚNG DẪN 36
TH   43

2
1
3
Fig.1
1
2
Fig.2
1
Fig.3
1
Fig.4
1
2
Fig.5
1
Fig.6
1
32
Fig.7
2
1
Fig.8
2

2
3
1
Fig.9
2
1
A
Fig.10
2
1
Fig.11
1
2
A
B
3
Fig.12
Fig.13
Fig.14
3

Fig.15
Fig.16
1
Fig.17
4

5ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: DPB184
Max. cutting
capacity
Round workpiece 51 mm dia.
Rectangular workpiece 51 mm x 51 mm
Blade speed 0 - 3.2 m/s
(0 - 190 m/min)
Blade size Length 730 mm
Width 13 mm
Thickness 0.5 mm
Dimensions (L x W x H) without wheel cover 373 mm x 162 mm x 223 mm
Rated voltage D.C. 18 V
Net weight without wheel cover 3.3 - 3.6 kg
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydi󰀨erfromcountrytocountry.
• Theweightmaydi󰀨erdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
estcombination,accordingtoEPTA-Procedure01/2014,areshowninthetable.
Applicable battery cartridge and charger
Battery cartridge BL1815N/BL1820/BL1820B/BL1830/BL1830B/BL1840/
BL1840B/BL1850/BL1850B/BL1860B
Charger DC18RC/DC18RD/DC18RE/DC18SD/DC18SE/DC18SF/
DC18SH
• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof
residence.
WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges
andchargersmaycauseinjuryand/orre.
Symbols
Thefollowingsshowthesymbolswhichmaybeused
for the equipment. Be sure that you understand their
meaningbeforeuse.
Read instruction manual.
Wear safety glasses.
Ni-MH
Li-ion
OnlyforEUcountries
Do not dispose of electric equipment or
batterypacktogetherwithhouseholdwaste
material!
InobservanceoftheEuropeanDirectives,
onWasteElectricandElectronic
EquipmentandBatteriesandAccumulators
andWasteBatteriesandAccumulators
and their implementation in accordance
with national laws, electric equipment and
batteriesandbatterypack(s)thathave
reachedtheendoftheirlifemustbecol-
lected separately and returned to an envi-
ronmentallycompatiblerecyclingfacility.
Intended use
The tool is intended for cutting in plastic and ferrous
materials.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool.Failuretofollowallinstructions
listedbelowmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
The term “power tool” in the warnings refers to your
mains-operated(corded)powertoolorbattery-operated
(cordless) power tool.

6ENGLISH
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust.Powertoolscreatesparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiedplugsandmatchingoutletswill
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tricshockifyourbodyisearthedorgrounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
acordsuitableforoutdoorusereducestheriskof
electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
7. Power tools can produce electromagnetic
elds (EMF) that are not harmful to the user.
However, users of pacemakers and other similar
medical devices should contact the maker of their
deviceand/ordoctorforadvicebeforeoperating
this power tool.
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication.Amomentofinattentionwhileoperating
powertoolsmayresultinseriouspersonalinjury.
2. Use personal protective equipment. Always
wear eye protection.Protectiveequipmentsuch
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
willreducepersonalinjuries.
3. Prevent unintentional starting. Ensure the
switch is in the o󰀨-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
yourngerontheswitchorenergisingpowertools
that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on.Awrenchorakeyleft
attached to a rotating part of the power tool may
resultinpersonalinjury.
5. Do not overreach. Keep proper footing and
balance at all times.Thisenablesbettercontrol
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.Looseclothes,jewelleryor
longhaircanbecaughtinmovingparts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
8. Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles.Acarelessaction
cancausesevereinjurywithinafractionofa
second.
9. Always wear protective goggles to protect
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/New Zealand. In Australia/New
Zealand, it is legally required to wear a face
shield to protect your face, too.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
powertoolwilldothejobbetterandsaferatthe
rate for which it was designed.
2. Do not use the power tool if the switch does
not turn it on and o󰀨.Anypowertoolthatcannot
becontrolledwiththeswitchisdangerousand
mustberepaired.
3. Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any adjust-
ments, changing accessories, or storing power
tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool.Powertoolsaredangerousinthe
hands of untrained users.

7ENGLISH
5. Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may a󰀨ect the power tool’s operation. If dam-
aged, have the power tool repaired before use.
Manyaccidentsarecausedbypoorlymaintained
power tools.
6. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges
arelesslikelytobindandareeasiertocontrol.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
foroperationsdi󰀨erentfromthoseintendedcould
result in a hazardous situation.
8. Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected
situations.
9. When using the tool, do not wear cloth work
gloves which may be entangled. The entangle-
ment of cloth work gloves in the moving parts may
resultinpersonalinjury.
Battery tool use and care
1. Recharge only with the charger specied by
the manufacturer.Achargerthatissuitablefor
onetypeofbatterypackmaycreateariskofre
whenusedwithanotherbatterypack.
2. Use power tools only with specically desig-
nated battery packs.Useofanyotherbattery
packsmaycreateariskofinjuryandre.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.Shortingthebatterytermi-
nalstogethermaycauseburnsorare.
4. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help.Liquidejectedfromthebatterymaycause
irritationorburns.
5. Do not use a battery pack or tool that is dam-
aged or modied.Damagedormodiedbatteries
mayexhibitunpredictablebehaviourresultingin
re,explosionorriskofinjury.
6. Do not expose a battery pack or tool to re or
excessive temperature.Exposuretoreortem-
peratureabove130°Cmaycauseexplosion.
7. Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specied in the instruc-
tions. Charging improperly or at temperatures
outsidethespeciedrangemaydamagethe
batteryandincreasetheriskofre.
Service
1. Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2. Never service damaged battery packs. Service
ofbatterypacksshouldonlybeperformedbythe
manufacturer or authorized service providers.
3. Follow instruction for lubricating and chang-
ing accessories.
Cordless Portable Band Saw Safety
Warnings
1. Hold power tool by insulated gripping sur-
faces, when performing an operation where
the cutting accessory may contact hidden
wiring. Cutting accessories contacting a “live”
wire may make exposed metal parts of the power
tool “live” and could give the operator an electric
shock.
2. Use only blades which are listed in
“SPECIFICATIONS”.
3. Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blade immediately.
4. Secure the workpiece rmly. When cutting a
bundle of workpieces, be sure that all work-
pieces are secured together rmly before
cutting.
5. Cutting workpieces covered with oil can cause
the blade to come o󰀨 unexpectedly. Wipe o󰀨
all excess oil from workpieces before cutting.
6. Never use the cutting oil as a cutting lubricant.
Use only Makita cutting wax.
7. Hold the tool rmly.
8. Keep hands away from rotating parts.
9. When cutting metal, be cautious of hot ying
chips.
10. Do not leave the tool running unattended.
11. Do not touch the blade or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.

8ENGLISH
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
Forcommercialtransportse.g.bythirdparties,
forwarding agents, special requirement on pack-
agingandlabelingmustbeobserved.
Forpreparationoftheitembeingshipped,consult-
ing an expert for hazardous material is required.
Pleasealsoobservepossiblymoredetailed
national regulations.
Tapeormasko󰀨opencontactsandpackupthe
batteryinsuchamannerthatitcannotmove
around in the packaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specied by Makita.Installingthebatteriesto
non-compliantproductsmayresultinare,exces-
sive heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Useofnon-genuineMakitabatteries,orbatteriesthat
havebeenaltered,mayresultinthebatterybursting
causingres,personalinjuryanddamage.Itwill
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. Charge the battery cartridge if you do not use
it for a long period (more than six months).
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION: Always switch o󰀨 the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge.Failuretoholdthetoolandthebattery
cartridgermlymaycausethemtoslipo󰀨yourhands
andresultindamagetothetoolandbatterycartridge
andapersonalinjury.
►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge
Toremovethebatterycartridge,slideitfromthetool
whileslidingthebuttononthefrontofthecartridge.
Toinstallthebatterycartridge,alignthetongueonthe
batterycartridgewiththegrooveinthehousingandslip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
uppersideofthebutton,itisnotlockedcompletely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
itmayaccidentallyfalloutofthetool,causinginjuryto
you or someone around you.
CAUTION: Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
notbeinginsertedcorrectly.

9ENGLISH
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
►Fig.2: 1. Indicator lamps 2.Checkbutton
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
light up for a few seconds.
Indicator lamps Remaining
capacity
Lighted O󰀨 Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
may have
malfunctioned.
NOTE: Depending on the conditions of use and the
ambienttemperature,theindicationmaydi󰀨erslightly
from the actual capacity.
Tool / battery protection system
Thetoolisequippedwithatool/batteryprotectionsys-
tem.Thissystemautomaticallycutso󰀨powertothe
motortoextendtoolandbatterylife.Thetoolwillauto-
maticallystopduringoperationifthetoolorbatteryis
placed under one of the following conditions:
Overload protection
Whenthebatteryisoperatedinamannerthatcauses
ittodrawanabnormallyhighcurrent,thetoolautomat-
ically stops without any indication. In this situation, turn
thetoolo󰀨andstoptheapplicationthatcausedthetool
tobecomeoverloaded.Thenturnthetoolontorestart.
Overheat protection
When the tool is overheated, the tool stops automat-
icallyandthelampstartsblinking.Inthissituation,
letthetoolandbatterycoolbeforeturningthetoolon
again.
Overdischarge protection
Whenthebatterycapacityisnotenough,thetoolstops
automatically.Inthiscase,removethebatteryfromthe
toolandchargethebattery.
Hook
CAUTION: Never hang the tool at high or
potentially unstable location.
The hook is convenient for hanging the tool temporarily.
To use the hook, simply lift up hook until it snaps into
the open position.
When not in use, always lower hook until it snaps into
the closed position.
Open position
►Fig.3: 1. Hook
Closed position
►Fig.4: 1. Hook
Switch action
WARNING: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the “OFF” position when released.
WARNING: NEVER defeat the lock-o󰀨 button
by taping down or some other means.Aswitchwith
anegatedlock-o󰀨buttonmayresultinunintentional
operationandseriouspersonalinjury.
WARNING: NEVER use the tool if it runs when
you simply pull the switch trigger without press-
ing the lock-o󰀨 button.Aswitchinneedofrepair
may result in unintentional operation and serious
personalinjury.ReturntooltoaMakitaservicecenter
forproperrepairsBEFOREfurtherusage.
Topreventtheswitchtriggerfrombeingaccidentally
pulled,alock-o󰀨buttonisprovided.Tostartthetool,
depressthelock-o󰀨buttonandpulltheswitchtrigger.
Toolspeedisincreasedbyincreasingpressureonthe
switch trigger. Release the switch trigger to stop.
►Fig.5: 1.Lock-o󰀨button2. Switch trigger
Lighting up the front lamp
CAUTION: Do not look in the light or see the
source of light directly.
Pulltheswitchtriggertolightupthelamp.Thelamp
keepsonlightingwhiletheswitchtriggerisbeingpulled.
The lamp goes out approximately 10 seconds after
releasing the switch trigger.
►Fig.6: 1. Lamp
NOTE: Do not apply impact to the lamp, which may
cause damage or shorted service time to it.
NOTE:Useadryclothtowipethedirto󰀨thelensof
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
NOTE:Whenthetoolisoverheated,thelampblinks
foroneminute,andthengoeso󰀨.Inthiscase,cool
downthetoolbeforeoperatingagain.

10 ENGLISH
ASSEMBLY
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing the band saw
blade
CAUTION: Oil on the band saw blade can
cause the blade to slip or come o󰀨 unexpectedly.
Wipe o󰀨 all excess oil with a cloth before install-
ing the band saw blade.
CAUTION: Always wear protective gloves
when handling the band saw blade.
CAUTION: Use caution when handling the
band saw blade to avoid cut by the sharp edge of
the blade teeth.
CAUTION: Keep your body away from
the band saw blade when checking the blade
movement.
CAUTION: When turning the blade tightening
lever clockwise to release the tension on the band
saw blade, point the tool downward because the
band saw blade may come o󰀨 unexpectedly.
Toinstallthebandsawblade:
1. Turnthebladetighteningleverclockwiseuntilit
stops to loosen the wheel.
►Fig.7: 1. Tighten 2. Loosen 3. Blade tightening lever
2. Open the wheel cover.
►Fig.8: 1. Wheel cover 2. Hook
NOTICE: When opening the wheel cover, open
and release both the hooks simultaneously.
Opening only one hook may cause crack on the
wheel cover.
3. Matchthedirectionofthearrowsonthebandsaw
bladeandonthewheels.
4. Insertthenon-serratedsideofthebandsawblade
into the upper holder and lower holder. Make sure the
bandsawbladeinbothupperandlowerholdertouches
tothebottombearings.
►Fig.9: 1. Lower holder 2. Upper holder 3. Bottom
bearing
5. Withpressingthemiddlepartofthebandsaw
blade,positionthebladearoundonewheel.Movingthe
wheeltoAsidemakesiteasiertodoso.
►Fig.10: 1. Wheel 2.Rubbertire
6. Positionthebandsawbladeontheotherwheel
similarly.
7. Positiontheedgeofthebandsawbladeonrubber
tire.
8. Holdthebandsawbladeinplaceandturnthe
bladetighteninglevercounterclockwiseuntilitstops.
Thisplacespropertensiononthebandsawblade.
9. Close the wheel cover.
NOTICE: Make sure that the band saw blade is
correctly positioned around the wheels.
NOTICE: Start and stop the tool two or three
times to make sure that the band saw blade runs
properly on the wheels.
Toremovethebandsawblade,followtheinstallation
procedure in reverse.
Adjusting blade track
Whenthebandsawbladetendstoslipoutfromthe
wheel,adjustthebladetrack.
Toadjust,insertthehexwrenchintotheadjustment
hole as illustrated and make a quarter turn clockwise.
Afterthat,checkifthebandsawbladedoesnotslipout.
If it still slips out, make another quarter turn and check
untilthebandsawbladedoesnotslipout.
►Fig.11: 1. Hex wrench 2.Adjustmenthole
Adjusting the stopper plate position
In the ordinary operation, protrude the stopper plate to
theAsidefully.
Whenthestopperplatehitsagainsttheobstaclessuch
asawallorthelikeatthenishingofacut,loosentwo
boltsandslideittotheBsideinthegure.
Afterslidingthestopperplate,secureitbytightening
twoboltsrmly.
►Fig.12: 1. Stopper plate 2. Bolts 3.Bandsawblade
OPERATION
CAUTION: Always insert the battery cartridge
all the way until it locks in place. If you can see the
redindicatorontheuppersideofthebutton,itisnot
locked completely. Insert it fully until the red indicator
cannotbeseen.Ifnot,itmayaccidentallyfalloutof
thetool,causinginjurytoyouorsomeonearound
you.
CAUTION: Always hold the handle. Never
hold the tool body or guards. Hands may slip from
theselocationsandcontactwiththebandsawblade.
Itmayresultinpersonalinjury.
CAUTION: Make sure that the wheel cover is
closed securely.
CAUTION: Make sure to hold the tool rmly
when turning on or o󰀨 the tool or when cutting.
Otherwisethetoolmayfallandcausepersonalinjury.
CAUTION: Always wear gloves to protect
your hands from hot ying chips when cutting
metal.
CAUTION: Keep your body and face away
from the band saw blade and ying chips.
Forstablecut,alwayskeepatleasttwoteethinthecut.
►Fig.13
Applythebandsawbladetothesuitablecuttingposi-
tion on the workpiece as illustrated.
►Fig.14

11 ENGLISH
1. Hold the tool as illustrated.
Before turning on the tool, always make sure that the
stopperplatecontactstheworkpieceandthebandsaw
bladeisclearoftheworkpiece.
►Fig.15
2. Turnthetoolon.Gentlylowerthebladeintothe
cut. The weight of the tool or slightly pressing the tool
will supply adequate pressure for the cutting. Do not
force the tool.
►Fig.16
3. Asyoureachtheendofacut,releasepressure
and lift the tool slightly so that the tool will not fall
against the workpiece.
NOTICE: Applying excessive pressure to the
tool or twisting of the band saw blade may cause
bevel cutting or damage to the blade.
NOTICE: When not using the tool for a long
period of time, remove the band saw blade from
the tool.
NOTICE: If the tool is operated continuously
until the battery cartridge has discharged, allow
the tool to rest for 15 minutes before proceeding
with a fresh battery.
Cutting lubricant
Optional accessory
CAUTION: Never use cutting oil or apply
excessive amount of wax to the band saw blade. It
maycausethebladetosliporcomeo󰀨unexpectedly.
CAUTION: When cutting cast iron, do not use
any cutting wax.
When cutting metals, use Makita cutting wax as a cut-
tinglubricant.Toapplythecuttingwaxtotheteethof
thebandsawblade,removeacapofthecuttingwax,
start the tool and cut into the cutting wax as illustrated.
►Fig.17: 1. Cutting wax
MAINTENANCE
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
TomaintainproductSAFETYandRELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers, always using Makita replacement parts.
Cleaning
CAUTION: Wax and chips on the rubber tires
on the wheel may cause the band saw blade to
slip and come o󰀨 unexpectedly. Use a dry cloth to
remove wax and chips from the rubber tires.
Afteruse,removewax,chipsanddustfromthetool,
rubbertiresonthewheelandthebandsawblade.
Replacing rubber tires on the
wheels
Replacetherubbertireswhenthebandsawbladeslips
ordoesnottrackproperlybecauseofbadlyworntires.
Toreplacetherubbertire,askfortheMakitaAuthorized
orFactoryServiceCenters.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual. The use of any other
accessories or attachments might present a risk of
injurytopersons.Onlyuseaccessoryorattachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Makitagenuinebatteryandcharger
• Bandsawblades
• Cutting wax
NOTE:Someitemsinthelistmaybeincludedinthe
tool package as standard accessories. They may
di󰀨erfromcountrytocountry.

12
中文简体
中文简体 (原本)
规格
型号： DPB184
最大剪
切能力
圆形工件 51 mm 直径
矩形工件 51 mm ×51 mm
带锯速度 0 - 3.2 m/s
(0 - 190 m/min)
锯片尺寸 长度 730 mm
宽度 13 mm
厚度 0.5 mm
尺寸（长×宽×高）
（不含轮罩）
373 mm ×162 mm ×223 mm
额定电压 D.C. 18 V
净重（不含轮罩） 3.3 - 3.6 kg
• 生产者保留变更规格不另行通知之权利。
• 规格可能因销往国家之不同而异。
• 重量因附件（包括电池组）而异。根据EPTA-Procedure01/2014，最重与最轻的组合见
表格。
适用电池组和充电器
电池组 BL1815N / BL1820 / BL1820B / BL1830 /
BL1830B/BL1840/BL1840B/BL1850/
BL1850B / BL1860B
充电器 DC18RC/DC18RD/DC18RE/DC18SD/
DC18SE/DC18SF/DC18SH
• 部分以上所列电池组和充电器是否适用视用户所在地区而异。
警告： 请仅使用以上所列电池组和充电器。使用其他类型的电池组或充电器可能会导
致人身伤害和／或失火。
符号
以下显示本设备可能会使用的符号。在使用
工具之前，请务必理解其含义。
阅读使用说明书。
佩带安全眼镜。
Ni-MH
Li-ion 仅限于欧盟国家
请勿将电气设备或电池组与家
庭普通废弃物一同丢弃！
请务必遵守欧洲关于废弃电子
电气设备、电池和蓄电池以及
废弃电池和蓄电池的指令并根
据法律法规执行。达到使用寿
命的电气设备和电池组必须分
类回收至符合环境保护规定的
再循环机构。
用途
本工具用于切割塑料和铁质材料。

13
中文简体
安全警告
电动工具通用安全警告
警告： 阅读随电动工具提供的所有安全
警告、说明、图示和规定。不遵照以下所列
说明会导致电击、着火和／或严重伤害。
保存所有警告和说明书以备
查阅。
警告中的术语“电动工具”是指市电驱动
（有线）电动工具或电池驱动（无线）电动
工具。
工作场地的安全
1. 保持工作场地清洁和明亮。杂乱和黑暗
的场地会引发事故。
2. 不要在易爆环境，如有易燃液体、气体
或粉尘的环境下操作电动工具。电动工
具产生的火花会点燃粉尘或气体。
3. 操作电动工具时，远离儿童和旁观者。注
意力不集中会使你失去对工具的控制。
电气安全
1. 电动工具插头必须与插座相配。绝不能
以任何方式改装插头。需接地的电动工
具不能使用任何转换插头。未经改装的
插头和相配的插座将降低电击风险。
2. 避免人体接触接地表面，如管道、散热
片和冰箱。如果你身体接触接地表面会
增加电击风险。
3. 不得将电动工具暴露在雨中或潮湿环境
中。水进入电动工具将增加电击风险。
4. 不得滥用软线。绝不能用软线搬运、拉
动电动工具或拔出其插头。使软线远离
热源、油、锐边或运动部件。受损或缠
绕的软线会增加电击风险。
5. 当在户外使用电动工具时，使用适合户
外使用的延长线。适合户外使用的电线
将降低电击风险。
6. 如果无法避免在潮湿环境中操作电动工
具，应使用带有剩余电流装置（RCD）
保护的电源。RCD的使用可降低电击
风险。
7. 电动工具会产生对用户无害的电磁场
（EMF）。但是，起搏器和其他类似医
疗设备的用户应在操作本电动工具前咨
询其设备的制造商和／或医生寻求建议。
人身安全
1. 保持警觉，当操作电动工具时关注所从
事的操作并保持清醒。当你感到疲倦，
或在有药物、酒精或治疗反应时，不要
操作电动工具。在操作电动工具时瞬间
的疏忽会导致严重人身伤害。
2. 使用个人防护装置。始终佩戴护目镜。
防护装置，诸如适当条件下使用防尘面
具、防滑安全鞋、安全帽、听力防护等
装置能减少人身伤害。
3. 防止意外起动。在连接电源和/或电池
包、拿起或搬运工具前确保开关处于关
断位置。手指放在开关上搬运工具或开
关处于接通时通电会导致危险。
4. 在电动工具接通之前，拿掉所有调节钥
匙或扳手。遗留在电动工具旋转零件上
的扳手或钥匙会导致人身伤害。
5. 手不要过分伸展。时刻注意立足点和身
体平衡。这样能在意外情况下能更好地
控制住电动工具。
6. 着装适当。不要穿宽松衣服或佩戴饰品。
让你的头发和衣服远离运动部件。宽松衣
服、佩饰或长发可能会卷入运动部件。
7. 如果提供了与排屑、集尘设备连接用的
装置，要确保其连接完好且使用得当。
使用集尘装置可降低尘屑引起的危险。
8. 不要因为频繁使用工具而产生的熟悉感而
掉以轻心，忽视工具的安全准则。某个粗
心的动作可能在瞬间导致严重的伤害。
9. 使用电动工具时请始终佩带护目镜以
免伤害眼睛。护目镜须符合美国ANSI
Z87.1、欧洲EN 166或者澳大利亚／新
西兰的AS/NZS 1336的规定。在澳大
利亚／新西兰，法律要求佩带面罩保护
脸部。
雇主有责任监督工具操作者和其他近工
作区域人员佩带合适的安全防护设备。

14
中文简体
电动工具使用和注意事项
1. 不要勉强使用电动工具，根据用途使用
合适的电动工具。选用合适的按照额定
值设计的电动工具会使你工作更有效、
更安全。
2. 如果开关不能接通或关断电源，则不能
使用该电动工具。不能通过开关来控制
的电动工具是危险的且必须进行修理。
3. 在进行任何调节、更换附件或贮存电动
工具之前，必须从电源上拔掉插头和/或
卸下电池包（如可拆卸）。这种防护性
的安全措施降低了电动工具意外起动的
风险。
4. 将闲置不用的电动工具贮存在儿童所及
范围之外，并且不允许不熟悉电动工具
和不了解这些说明的人操作电动工具。
电动工具在未经培训的使用者手中是危
险的。
5. 维护电动工具及其附件。检查运动部件是
否调整到位或卡住，检查零件破损情况和
影响电动工具运行的其他状况。如有损
坏，应在使用前修理好电动工具。许多
事故是由维护不良的电动工具引发的。
6. 保持切削刀具锋利和清洁。维护良好地
有锋利切削刃的刀具不易卡住而且容易
控制。
7. 按照使用说明书，并考虑作业条件和要
进行的作业来选择电动工具、附件和工
具的刀头等。将电动工具用于那些与其
用途不符的操作可能会导致危险情况。
8. 保持手柄和握持表面干燥、清洁，不得
沾有油脂。在意外的情况下，湿滑的手
柄不能保证握持的安全和对工具的控制。
9. 使用本工具时，请勿佩戴可能会缠结的
布质工作手套。布质工作手套卷入移动
部件可能会造成人身伤害。
电池式工具使用和注意事项
1. 仅使用生产者规定的充电器充电。将适
用于某种电池包的充电器用到其他电池
包时可能会发生着火危险。
2. 仅使用配有专用电池包的电动工具。使用
其他电池包可能会产生伤害和着火危险。
3. 当电池包不用时，将它远离其他金属物
体，例如回形针、硬币、钥匙、钉子、
螺钉或其他小金属物体，以防电池包一
端与另一端连接。电池组端部短路可能
会引起燃烧或着火。
4. 在滥用条件下，液体可能会从电池组中溅
出；应避免接触。如果意外碰到液体，用
水冲洗。如果液体碰到了眼睛，还应寻求
医疗帮助。从电池中溅出的液体可能会发
生腐蚀或燃烧。
5. 不要使用损坏或改装过的电池包或工具。
损坏或改装过的电池组可能呈现无法预测
的结果，导致着火、爆炸或伤害。
6. 不要将电池包暴露于火或高温中。电池
包暴露于火或高于130 ℃的高温中可能
导致爆炸。
7. 遵循所有充电说明。不要在说明书中指
定的温度范围之外给电池包或电动工具
充电。不正确或在指定的温度范围外充
电可能会损坏电池和增加着火的风险。
维修
1. 让专业维修人员使用相同的备件维修电
动工具。这将保证所维修的电动工具的
安全。
2. 决不能维修损坏的电池包。电池包仅能由
生产者或其授权的维修服务商进行维修。
3. 上润滑油及更换附件时请遵循本说明书
指示。
充电式轻便带锯使用安全警告
1. 当进行作业时切割附件可能会接触到隐
藏的电线，请握住电动工具的绝缘抓握
表面。切割附件接触到“带电”的电线
时，电动工具上曝露的金属部分可能也
会“带电”，并使操作者触电。
2. 请仅使用列于“规格”中的锯片。
3. 操作之前，请仔细检查锯片上是否有裂
缝或损坏。应立即更换有裂缝或损坏的
锯片。
4. 牢固固定工件。切割成束工件时，请在
切割前确保所有工件紧紧固定在一起。
5. 切割覆盖有油层的工件可能导致锯片意
外脱落。切割前，擦掉工件上所有过多
的油脂。
6. 切勿使用切削油作为切割润滑油。请仅
使用Makita（牧田）切削蜡。
7. 请牢握本工具。
8. 手应远离旋转的部件。
9. 切割金属时，请小心灼热的飞溅碎片。
10. 请勿在无人照看时运行工具。
11. 操作之后，请勿立刻触摸锯片或工件，因
为它们可能会非常烫而导致烫伤皮肤。

15
中文简体
电池组的重要安全注意事项
1. 在使用电池组之前，请仔细通读所有的
说明以及（1）电池充电器，（2）电
池，以及（3）使用电池的产品上的警
告标记。
2. 请勿拆解电池组。
3. 如果机器运行时间变得过短，请立即停
止使用。否则可能会导致过热、起火甚
至爆炸。
4. 如果电解液进入您的眼睛，请用清水将
其冲洗干净并立即就医。否则可能会导
致视力受损。
5. 请勿使电池组短路：
(1) 请勿使任何导电材料碰触到端子。
(2) 避免将电池组与其他金属物品如钉
子、硬币等放置在同一容器内。
(3) 请勿将电池组置于水中或使其淋雨。
电池短路将产生大的电流，导致过热，
并可能导致起火甚至击穿。
6. 请勿将工具和电池组置于温度可能达到
或超过50 °C（122 °F）的场所。
7. 即使电池组已经严重损坏或完全磨损，也
请勿焚烧电池组。电池组会在火中爆炸。
8. 请小心，勿撞击电池或使其掉落。
9. 请勿使用损坏的电池。
10. 本工具附带的锂离子电池需符合危险品
法规要求。
第三方或转运代理等进行商业运输时，
应遵循包装和标识方面的特殊要求。
有关运输项目的准备作业，咨询危险品
方面的专业人士。同时，请遵守可能更
为详尽的国家法规。
请使用胶带保护且勿遮掩表面的联络信
息，并牢固封装电池，使电池在包装内
不可动。
11. 丢弃电池组时，需将其从工具上卸下并
在安全地带进行处理。关于如何处理废
弃的电池，请遵循当地法规。
12. 仅将电池用于Makita（牧田）指定的产
品。将电池安装至不兼容的产品会导致
起火、过热、爆炸或电解液泄漏。
13. 如长时间未使用工具，必须将电池从工
具内取出。
请保留此说明书。
小心： 请仅使用Makita（牧田）原装电
池。使用非Makita（牧田）原装电池或经过
改装的电池可能会导致电池爆炸，从而造成
火灾、人身伤害或物品受损。同时也会导致
牧田工具和充电器的牧田保修服务失效。
保持电池最大使用寿命的提示
1. 在电池组电量完全耗尽前及时充电。发
现工具电量低时，请停止工具操作，并
给电池组充电。
2. 请勿对已充满电的电池组重新充电。过
度充电将缩短电池的使用寿命。
3. 请在10 °C - 40 °C（50 °F - 104 °F）的
室温条件下给电池组充电。请在灼热的
电池组冷却后再充电。
4. 如果电池组长时间（超过六个月）未使
用，请给其充电。
功能描述
小心： 调节或检查工具功能之前，请
务必关闭工具的电源并取出电池组。
安装或拆卸电池组
小心： 安装或拆卸电池组之前，请务
必关闭工具电源。
小心： 安装或拆卸电池组时请握紧工
具和电池组。否则它们可能从您的手中滑
落，导致工具和电池组受损，甚至造成人
身伤害。
►图片1: 1. 红色指示灯 2. 按钮 3. 电池组
拆卸电池组时，按下电池组前侧的按钮，同
时将电池组从工具中抽出。
安装电池组时，要将电池组上的舌簧与外罩
上的凹槽对齐，然后推滑到位。将其完全插
入到位，直到电池组被锁定并发出卡嗒声为
止。如果插入后仍能看到按钮上侧的红色指
示灯，则说明电池组未完全锁紧。
小心： 务必完全装入电池组，直至看
不见红色指示灯。否则它可能会意外从工
具中脱落，从而造成自身或他人受伤。
小心： 请勿强行安装电池组。如果电
池组难以插入，可能是插入方法不当。

16
中文简体
显示电池的剩余电量
仅限带指示灯的电池组
►图片2: 1. 指示灯 2.CHECK（查看）
按钮
按电池组上的CHECK（查看）按钮可显示
电池剩余电量。指示灯将亮起数秒。
指示灯 剩余电量
点亮 熄灭 闪烁
75%至
100%
50%至
75%
25%至
50%
0%至
25%
给电池
充电。
电池可
能出现
故障。
注： 在不同的使用条件及环境温度下，指
示灯所示电量可能与实际情况略有不同。
工具／电池保护系统
本工具配备有工具／电池保护系统。该系统可
自动切断电机电源以延长工具和电池寿命。作
业时，如果工具或电池处于以下情况，工具将
会自动停止 运转。
过载保护
以导致异常高电流的方式操作电池时，工具
会自动停止运转，指示灯不闪烁。在这种情
况下，请关闭工具并停止导致工具过载的应
用操作。然后开启工具重新启动。
过热保护
工具过热时，工具将自动停止运转且指示灯
开始闪烁。在这种情况下，请待工具和电池
冷却后再重新开启工具。
过放电保护
电池电量不足时，本工具自动停止运转。此
时，请取出工具中的电池并予以充电。
挂钩
小心： 切勿将工具悬挂在高处或可能
不稳固的位置。
挂钩便于临时悬挂工具。
要使用挂钩时，只需提起挂钩使其咬在打开
位置即可。
不使用时，务必压低挂钩使其咬在关闭位置。
打开位置
►图片3: 1. 挂钩
关闭位置
►图片4: 1. 挂钩
开关操作
警告： 在将电池组插入工具之前，请
务必检查开关扳机是否能扣动自如，松开
时能否退回至“OFF”（关闭）位置。
警告： 切勿通过封住锁止按钮或其他
方法来弃用锁止按钮。在弃用开关锁止按
钮的情况下使用工具时可能会出现意外运
行的情况并导致严重的人身伤害。
警告： 如果当您只是扣动开关扳机而
没有按下锁止按钮时，工具即开始运行，
则切勿使用此工具。在开关需要维修的情
况下使用工具时可能会出现意外运行的情
况并导致严重的人身伤害。在进一步使用
该工具之前，请将其送回Makita（牧田）
维修中心进行正确的修理。
为避免使用者不小心扣动开关扳机，本工具
采用锁止按钮。要启动工具时，按下锁止按
钮，然后扣动开关扳机即可。
随着施加在开关扳机上的压力逐渐增大，工具
速度也会提高。松开开关扳机，工具即停止。
►图片5: 1. 锁止按钮 2. 开关扳机
点亮前灯
小心： 请勿直视灯光或光源。
扣动开关扳机以点亮照明灯。在扣动开关扳
机期间，此灯保持常亮。松开开关扳机约10
秒后，此灯将熄灭。
►图片6: 1. 照明灯

17
中文简体
注： 不要撞击照明灯，否则可能导致其损
坏或使用寿命缩短。
注： 请使用干布擦拭灯头灰。注意不要刮
花灯头，否则会降低亮度。
注： 当工具过热时，灯会闪烁一分钟，随
后熄灭。在这种情况下，请将工具冷却后
再重新进行操作。
装配
小心： 对工具进行任何装配操作前，请
务必关闭工具电源，并取出电池组。
安装或拆卸带锯锯片
小心： 带锯锯片上的油可导致锯片意外
滑动或脱落。安装带锯锯片前，用布擦掉所
有过多的油脂。
小心： 处理带锯锯片时，请务必佩戴
手套。
小心： 处理带锯锯片时请小心，以防被
锯片锯齿的尖锐边缘割伤。
小心： 检查锯片运行是否正常时，勿使
身体靠近带锯锯片。
小心： 顺时针旋转锯片拧紧杆以释放带
锯锯片上的张力时，请将工具朝向下方，因
为带锯锯片可能会意外脱落。
安装带锯锯片：
1. 顺时针旋转锯片拧紧杆直至其停止即可
松开轮子。
►图片7: 1. 拧紧 2. 拧松 3. 锯片拧紧杆
2. 打开轮罩。
►图片8: 1. 轮罩 2. 挂钩
注意： 打开轮罩时，同时打开并释放两
个挂钩。如果仅打开一个挂钩可能会导致
轮罩破裂。
3. 使带锯锯片上的箭头方向与轮上的箭头
方向相吻合。
4. 将带锯锯片的非锯齿边插入上部固定夹
和下部固定夹。确保上部固定夹和下部固定
夹中的带锯锯片与底部轴承接触。
►图片9: 1. 下部固定夹 2. 上部固定夹
3. 底部轴承
5. 通过按压带锯锯片中间部分，将锯片缠
绕至其中一轮。向A侧移动此轮更方便操作。
►图片10: 1. 轮子 2. 橡胶轮箍
6. 用同样的方式将带锯锯片缠绕至另一
轮上。
7. 将带锯锯片的边缘正确置于橡胶轮箍上。
8. 将带锯锯片固定到位，然后逆时针旋转
锯片拧紧杆直至其停止为止。这使得带锯锯
片具有适当的张力。
9. 关闭轮罩。
注意： 确保带锯锯片正确缠绕各轮。
注意： 启动并停止工具两到三次，以确保
带锯锯片在砂轮上运行正常。
拆卸带锯锯片时，请按照与安装相反的步骤
进行。
调节锯片轨道
当带锯锯片容易从轮子上滑脱时，请调节锯
片轨道。
进行调节时，请如图所示将六角扳手插入调
节孔并顺时针旋转四分之一圈。然后，检查
带锯锯片是否会滑脱。
如果仍然会滑脱，请再旋转四分之一圈并进
行检查，直至带锯锯片不会滑脱。
►图片11: 1. 六角扳手 2. 调节孔
调节止动板位置
正常操作时，请将止动板完全伸至A侧。
在切割磨光时，如果止动板碰到墙壁或类似
的障碍物，请拧松两个螺栓，并将其滑动到
图中的B侧。
滑动止动板后，请通过拧紧两个螺栓将其
固定。
►图片12: 1. 止动板 2. 螺栓 3. 带锯锯片

18
中文简体
操作
小心： 插入电池组时请务必使其完全锁
紧到位。如果插入后仍能看到按钮上侧的
红色指示灯，则说明电池组未完全锁紧。
此时，须将电池适配器完全插入，直到红
色指示灯不亮为止。否则它可能会意外从
工具中脱落，从而造成自身或他人受伤。
小心： 请始终持握手柄。切勿持握工具
机身或轮罩。手可能会从这些位置滑出，
导致接触带锯锯片。这会造成人身伤害。
小心： 确保轮罩关闭牢固。
小心： 开启或关闭工具或切割时，务
必握紧工具。否则工具可能会摔落导致人
身伤害。
小心： 切割金属时，请务必佩带手套，
以保护您免受灼热飞溅碎片的伤害。
小心： 确保身体和面部远离带锯锯片
和飞溅碎片。
为进行稳定切割，务必使至少两个锯齿切入
切口。
►图片13
如图所示，将带锯锯片置于工件上合适的切
割位置。
►图片14
1. 按照图示牢握本工具。
启动工具前，务必确保止动板接触工件，而
带锯锯片未接触工件。
►图片15
2. 启动工具并等待，直至带锯锯片达到全
速运转时再进行操作。轻轻将锯片降低到切
口。工具的重量或轻微按压工具即可为切割
提供足够的压力。不要强力按压工具。
►图片16
3. 即将结束切割时，请释放压力并略微抬
高工具，以免工具掉落在工件上。
注意： 在工具上施加过度压力或扭转带锯
锯片可能会导致斜切割或锯片受损。
注意： 长时间不使用工具时，请从工具上
拆下带锯锯片。
注意： 如果工具连续工作到电池组电量耗
尽，则应暂停使用工具15分钟，再用充电后
的电池继续操作。
切割油
选购附件
小心： 切勿在带锯锯片上使用切削油
或涂抹过多的蜡。其可导致锯片意外滑动
或脱落。
小心： 切割生铁时，请勿使用任何切
削蜡。
切割金属时，请使用Makita（牧田）切削蜡作
为切割油。要在带锯锯齿上涂抹切削蜡时，
请在取下切削蜡的盖帽后启动工具，然后如
图所示切入切削蜡。
►图片17: 1. 切削蜡
保养
小心： 检查或保养工具之前，请务必关
闭工具电源并取出电池组。
注意： 切勿使用汽油、苯、稀释剂、酒精
或类似物品清洁工具。否则可能会导致工具
变色、变形或出现裂缝。
为了保证产品的安全与可靠性，维修、任何
其他的维修保养或调节需由Makita（牧田）
授权的或工厂维修服务中心完成。务必使用
Makita（牧田）的替换部件。
清洁
小心： 轮上橡胶轮箍上的蜡和碎屑可导
致带锯锯片意外滑动或脱落。请使用干布清
除橡胶轮箍上的蜡和碎屑。
使用后，请从工具、轮上橡胶轮箍和带锯锯
片上清除蜡、碎屑和灰尘。
更换轮上的橡胶轮箍
请在由于轮箍严重磨损导致带锯锯片打滑或
轨迹异常时更换橡胶轮箍。
更换橡胶轮箍时，请联络Makita（牧田）授
权的或工厂维修服务中心。

19
中文简体
选购附件
小心： 这些附件或装置专用于本说明书
所列的Makita（牧田）工具。如使用其他厂
牌附件或装置，可能导致人身伤害。仅可将
附件或装置用于规定目的。
如您需要了解更多关于这些选购附件的信
息，请咨询当地的Makita（牧田）维修服务
中心。
•Makita（牧田）原装电池和充电器
• 带锯锯片
• 切削蜡
注： 本列表中的一些部件可能作为标准配
件包含于工具包装内。它们可能因销往国
家之不同而异。

20 BAHASA INDONESIA
BAHASA INDONESIA (Petunjuk Asli)
SPESIFIKASI
Model: DPB184
Kapasitas
pemotongan
maks
Bendakerjalingkaran 51 mm dia.
Bendakerjapersegi
panjang
51 mm x 51 mm
Kecepatanmatagergaji 0 - 3,2 m/s
(0 - 190 m/min)
Ukuran mata
gergaji
Panjang 730 mm
Lebar 13 mm
Ketebalan 0,5 mm
Dimensi(PxLxT)tanpapenutuproda 373 mm x 162 mm x 223 mm
Tegangan terukur D.C. 18 V
Beratbersihtanpapenutuproda 3,3 - 3,6 kg
• Karenakesinambunganprogrampenelitiandanpengembangankami,spesikasiyangdisebutkandisinidapat
berubahtanpapemberitahuan.
• Spesikasidapatberbedadarisatunegarakenegaralainnya.
• Beratalatmungkinberbedatergantungperangkattambahanyangdipasang,termasukkartridbaterai.
Kombinasialatterberatdanteringan,sesuaiProsedurEPTA01/2014,ditunjukkanpadatabel.
Kartrid dan pengisi daya baterai yang dapat digunakan
Kartridbaterai BL1815N/BL1820/BL1820B/BL1830/BL1830B/BL1840/
BL1840B/BL1850/BL1850B/BL1860B
Pengisidaya DC18RC/DC18RD/DC18RE/DC18SD/DC18SE/DC18SF/
DC18SH
• Beberapakartridbateraidanpengisidayayangtercantumdiatasmungkintidaktersedia,tergantungwilayah
tempattinggalAnda.
PERINGATAN: Hanya gunakan kartrid dan pengisi daya baterai yang tercantum di atas.Penggunaan
kartriddanpengisidayabaterailaindapatmenimbulkanrisikocederadan/ataukebakaran.
Simbol
Berikutiniadalahsimbol-simbolyangdapatdigunakan
padaperalatanini.PastikanAndamemahamiarti
masing-masingsimbolsebelummenggunakan
peralatan.
Bacapetunjukpenggunaan.
Gunakan kaca mata pengaman.
Ni-MH
Li-ion
Hanyauntuknegara-negaraUE
Janganmembuangperalatanlistrikatau
paketbateraibersama-samadengan
bahanlimbahrumahtangga!
DenganmemerhatikanPetunjukEropa,
tentangLimbahPeralatanListrikdan
ElektroniksertaBateraidanAkumulator
sertaLimbahBateraidanAkumulatordan
pelaksanaannya sesuai dengan ketentuan
hukum nasional, peralatan listrik dan
bateraidanpaketbateraiyangtelahhabis
umur pakainya harus dikumpulkan secara
terpisahdandikembalikankefasilitasdaur
ulangyangkompatibelsecaralingkungan.
Penggunaan
Penggunaanmesininiditujukanuntukmemotong
bahanplastikdanbesi.