Makita LS1040F Manual

Continuous Rating (W)
Voltage (V) Cycle (Hz) Input Output Max. Output(W)
110 1,000 2,300
2,300
4,600
2,300
2,300
2,300
1,000
1,000
1,000
1,000
1,650
1,650
1,650
1,650
1,650
120
220
230
240
15
15
7.9
7.5
7.2
Models No.
Description
PRODUCT
Current (A)
TECHNICAL INFORMATION
CONCEPTION AND MAIN APPLICATIONS
Specification
Standard equipment
Optional accessories
< Note > The standard equipment for the tool shown may differ from country to country.
P 1 / 8
50 / 60
50 / 60
50 / 60
50 / 60
50 / 60
Model LS1040F is advanced version of Model LS1040.
Maintain all the advantage of LS1040, plus fluorescent lamp
with inverter (Light up wide range and easy to watch
the cutting line in dimly-lit place.)
It's brief benefits are
*Higher rigidity of all over the body
*More accurate cut
*Bevel cut (left only)
*More efficient chip/sawdust collection
*More stable cutting by holding material
more widely with sub fence
Dimensions : mm ( " )
Width ( W )
Height ( H )
Length ( L ) 476 (18-3/4)
532 (21)
* 530 (20-7/8)
* Dust Bag Ass' y ---------------1 pc.
* Triangular Rule---------------- 1pc.
* Socket Wrench 13------------- 1 pc.
L
W
H
* Vise Ass'y (Vertical Vise)----1 pc.
* T.C.T. Saw Blade 255--------1 pc.
* Vise Ass'y (Horizontal Vise)
* Crown molding stopper set
* Various T.C.T. saw blades
* Ring 15.88 for the saw blade with arbor, 25.4mm
* Ring 16 for the saw blade with arbor, 25mm
* Ring 16 for the saw blade with arbor, 30mm
Diameter : mm (")
Arbor : mm (")
No load speed (min-1 = rpm)
Protection from electric shock by double insulation
Net weight : Kg (lbs)
Capacity with : mm (") * The equipped saw blade : 255mm (10') in diameter
Cord length : m (ft)
Lock off switch
Electric brake
Blade
Miter angle
Bevel angle 0
°
45 °
(left and right)
0 °
45 °
(left)
* Switch Button (as a spare) ----2 pcs.
* Sub Plate Assembly ---------1 pc.
* Holder 255 --------------------2 pcs.
255 (10) - 260 (10-1/4)
15.88 (5/8) for North America,
30mm (1-3/16) for Europe 25.4mm (1) for Others
2.0 m (6.5) for Australia 2.5 m (8.2) for others
Yes (only for high voltage area)
Yes
11.6 (25.5)
90.5 x 95
(5-9/16 x 3-3/4)
69 x 130
(2-3/4 x 5-1/8)
90.5 x 67
(5-9/16 x 2-5/8)
69 x 92
(2-3/4 x 3-5/8)
48 x 95
(1-7/8 x 3-3/4)
35 x 130
(1-3/8 x 5-1/8)
48 x 67
(1-7/8 x 2-5/8)
35 x 92
(1-3/8 x 3-5/8)
LS1040F
Miter saw 255mm (10")
* Holder set
* Set plate
* Fluorescent tube
* from grip 32 to lever 100

Repair P 2 / 8
< 1 > Lubrication
Apply MAKITA grease N. No.1 to the following portions marked with black triangle to protect
parts and product from unusual abrasion.
51
72
56
81
87
71
69
Guide rule
86
86
Compression
spring 28
Item No. Parts The portion to be lubricated
51 Blade case
Slide plate
Turn base
56 Sub fence The pivot portion where contacts with guide rule.
The pivot portion where accepts 87 turn base.
69 Hex bolt M10 The threaded portion.
71 Rod 16 The whole portion
The whole portion
72 Arm
Base
The portion where contacts 87 turn base.
The portion which contacts 72 arm.
The cylindric portion to which compression spring 28 is inserted.
The space for helical gear : Apply here by approx. 12g ( 0.42 oz.).
The portion where contacts 86 base.
The notch portion for setting miter angle.
Helical gear
81
87
Notch
portion
< Note > Take off saw blade from the machine for your safety, before repairing or maintenance !

Repair P 3 / 8
< 2 > Removing compression spring 28 and motor unit
1) Holding the motor unit at the lowest position, insert 2 pcs. of bars into the side holes of blade case. See Fig. 1.
( The size of bars are 125 - 130mm in length and 4 - 6.5mm in diameter as illustrated in Fig. 1A.)
So, compression spring 28 and spring holder cannot spring out of blade case, when separating blade case from
arm.
125 - 130mm
4 - 6.5mm
2) Disconnect the linkage of link plate with arm by unscrewing hex socket button head screw M6. See Fig. 2.
Hex socket head bolt M6x10 is located on blade case for fixing rod 16 which works as an axis. Loosen this
hex socket head bolt. See Fig. 2A. And take off rod 16 as illustrated in Fig. 2.
3) Separate motor unit from arm. See Fig. 3.
Fig. 1.
Fig. 1A
Hex socket button
head bolt M6
Flat washer 7
Ring 7
Link plate
Link plate
Arm
Fig. 2
Hex socket head
bolt M6x10
Rod 16
Fig. 2A
Arm
Motor unit
Fig. 3

Repair P 4 / 8
< 3 > Mounting compression spring 28 and motor section
4) Put the block between the inserted 2 bars. And set the separated motor unit on the turn base of arbor press.
as illustrated in Fig. 4.
5) Pressing the block with arbor press, take off the 2 bars. See Fig. 5.
6) Slowly reduce the pressure on the block. And then, spring holder and compression spring 28 can be removed
from motor unit. See Fig. 6 and Fig. 7.
(1) Insert compression spring 28 into the cylindric hole of blade case and put spring holder on the compression
spring 28. And then, put the block on the spring holder. See Fig. 8.
< Caution >
When reducing the pressure on the block, keep the motor unit so firmly that it does not tilt or slip from the turn
base. Otherwise, spring holder and compression spring 28 spring out of the motor unit, which can injure you.
Block
Fig. 4. Fig. 5.
Compression
spring 28
Spring holder
Fig. 6. Fig. 7.
Compression
spring 28
Spring holder
Fig. 8.
Block
Fig. 9
(2) Press down spring holder and compression spring 28 with arbor press, to the position where the bars can be
inserted into the side holes of blade case. See Fig. 9.
Keeping spring holder and compression spring 28 in the pressed condition, insert 2 bars into the side holes of
blade case. See Fig. 10.
Fig. 10

Repair P 5 / 8
Fig. 11
Link plate
Arm
Link plate
Arm
Fig. 12
Fig. 13 Fig. 14
Hex socket head
bolt M6x10
Rod 16
Fig. 12A
(3) Mount the motor unit to arm aligning the arm's holes with blade cases holes for inserting rod 16. See Fig. 11.
(4) Insert rod 16 which works as an axis for swinging motor unit. See Fig. 12. And fasten rod 16 with hex socket
head bolt M6x10. See Fig. 12A.
(5) Fasten link plate to arm with hex socket button head bolt M6. See Fig. 13.
And then, pressing down the motor unit, take off 2 bars from the side holes of blade case. See Fig. 14.
Hex socket button
head bolt M6
Flat washer 7
Ring 7
Link plate
Arm Bars
<Note> Apply adhesive to hex socket button head bolt M6.

Repair P 6 / 8
< 5 > Fastening of hex lock nut M8x13
Turn base has to be so fastened and adjusted with hex lock nut M8x13 that it can turn without trembling.
See Fig. 16.
For adjusting and fastening, employ socket wrench 13 which is supplied with this product.
< 4 > Mounting slide plates
Aligning with the circle portion (on which turn base slides.) of base, mount slide plates as illustrated in Fig. 15.
And then, apply MAKITA grease N. No.1 to the slide plates.
Fig. 15
Slide plates
Hex lock nut M8x13
Hex bolt M8x30
Flat washer 8
Turn base
Fig. 16

Circuit diagram P 7 / 8
Color index of lead wires
Black
White
Red
Orange
Yellow Field
(view from armature fan side)
Field
(view from commutator side)
For low voltage
For high voltage
Color index of lead wires
Black
White
Red
Orange
Purple
Gray
1
2
5
Switch
Terminal
block
Light assembly
Choke coil
Field
(armature fan side)
Field
(commutator side)
1
2
4
5
Switch
Terminal
block
Light assembly
Choke coil
3
4
* For some countries, the products can
be supplied without installing terminal
block and noise suppressor .
* For some countries, the products can
be supplied without installing choke
coil.
In this case, field is connected directly
to switch terminal No.2 with orange
lead wire.
* For some countries, the products can
be supplied without installing terminal
block soft starter circuit and noise
suppressor .
* For some countries, the products can
be supplied without installing choke
coil.
In this case, field is connected directly
to switch terminal No.2 with orange
lead wire.
Noise
suppressor
3
Noise
suppressor
Soft starter
circuit
Switch
for brake

Wiring diagram P 8 / 8
Switch
for brake Switch for brake
Choke coil
Put choke coil in
this position.
Do not slack lead wires
in motor housing.
Lead wires of light assembly
The receptacles connected to
switch for brake, have to be faced
to the wall of handle.
<Note>
For some countries, the products can
be supplied without installing terminal
block soft starter circuit, choke coil and
noise suppressor .