Manitou 200 ATJ User manual

200 ATJ
A1
*
A
*
DB
C1
*
C
*
FE
**
L
**
16
17
18
34
20
31
23
24
25
26
27
28B
28A
32
30
37
33
35
36
22
19
29
21
1
3
2
5
4
8
7
6A 6C 6E
6B 6D
6I
6F
6G
6H
6J
6K
6L
THIS ALL-TERRAIN AERIAL WORK PLATFORM IS DESIGNED TO OPERATE ON NATURAL OR UNDEVELOPED LAND, OR CONSTRUCTION SITES.
t
IMPORTANT
t
This document is a short recap on how to operate an aerial work platform and should in no way be substituted for the manual required by Directive 2006/45/EC, which should be read and
understood by the operator beforehand and stored in the basket of the aerial work platform.
All the instructions, including the safety instructions, described in the manual but not included in this document should be implemented and enforced.
The operator must have received proper training and must comply with the applicable road trac rules.
BASIC INSTRUCTION SHEET No. 833096EN (2019/03/01)
PLATFORM WEIGHT
- Unladen 10,050kg
- With nominal load 10,280kg
BASKET CAPACITY
- 2 people 230kg
PLATFORM SPEED
- Working speed 0.8km/h
- Tortoise working speed 2.5km/h
- Ramp working speed 2.5km/h
- Hare working speed 4.7km/h
DIMENSIONS
- A* 8,475mm
- A1* 6,260mm
- B 2,400mm
- C* 2,715mm
- C1* 2,855mm
- D 2,400mm
- E** 430mm
- F 340mm
- L** 495mm
TECHNICAL CHARACTERISTICS
GROUND CONTROL PANEL
1 - EMERGENCY STOP BUTTON
2 - IGNITION SWITCH
3 - ENGINE STARTER BUTTON
4- ENGINE STARTING MODE BUTTON
5 - CONTROL SELECTION SWITCH ON THE GROUND/ IN THE BASKET
6 - CONTROL KEYS:
6A - RAISE THE JIB
6B - LOWER THE JIB
6C - EXTEND THE TELESCOPE
6D - RETRACT THE TELESCOPE
6E - RAISE THE MAIN ARM
6F - LOWER THE MAIN ARM
6G - LIFT THE SECONDARY ARM
6H - LOWER THE SECONDARY ARM
6I - TURN THE TURNTABLE TO THE LEFT
6J - TURN THE TURNTABLE TO THE RIGHT
6K - TILT BASKET UPWARDS
6L - TILT BASKET DOWN
7 - INTERFACE SCREEN NAVIGATION KEYS
8 - INTERFACE SCREEN
CONTROL PANEL IN THE BASKET
16 - EMERGENCY STOP BUTTON
17 - PREHEAT INDICATOR LIGHT
18 - ENGINE STARTER BUTTON
19 - HORN BUTTON
20 - BASKET ROTATION SWITCH
21 - JIB SWITCH
22 - BASKET TILT SWITCH
23 - MAIN ARM AND TURNTABLE CONTROL HANDLE
24 - SECONDARY ARM AND TELESCOPE CONTROL HANDLE
25 - DRIVING/STEERING CONTROL HANDLE
26 - DRIVING SPEED SELECTION SWITCH
27 - STEERING MODE SELECTION SWITCH
28A - FRONT WHEEL ALIGNMENT INDICATOR LIGHTS
28B - REAR WHEEL ALIGNMENT INDICATOR LIGHTS
29 - DIFFERENTIAL LOCKING BUTTON
30 - TILTING/OSCILLATION WARNING LIGHT
31 - "USE ON SLOPE" BUTTON
32 - OVERLOAD WARNING LIGHT
33 - FAULT WARNING LIGHT
34 - LOW FUEL LEVEL WARNING LIGHT
35 - BACKUP PUMP BUTTON
36 - GENERATOR BUTTON (OPTION: GENERATOR)
37 - RESET BUTTON (OPTION: «SAFEMANSYSTEM»)
* max. value depending on the wheel model - ** min. value depending on the wheel model

5°
0 2 4 6 8 10 12
2
4
6
8
10
12
14
16
18
20
024681012
230 kg
510 lbs
=
=
+
+
70 kg
155 lbs 2
5
AB
27
t
IMPORTANT
t
Operators should be aware of the risks connected with using the lift platform, notably:
- Risk of losing control.
- Risk of losing lateral stability of the lift platform.
- A safety helmet and a harness MUST be worn when using the platform.
PLATFORM WORKING AREA
SLOPE AND OVERLOAD
TURNTABLE ROTATION BLOCK
EMERGENCY PROCEDURE
ELECTRICAL HAZARD
BACKUP PUMP
• Before using the platform, check
the condition of the ground and
the bearing surfaces.
• If the wind speed is in excess of
45km/h, do not use the platform.
• Do not forget to mark out the
working area of the platform.
Max. permissible slope: 5°
• When the maximum
permissible slope is reached,
an audible alarm will sound
intermittently.
Overload:
• If the basket is overloaded,
an audible alarm will sound
continuously.
• Button B make it possible
to carry out all basket
movements in order to return
it to the ground in the event of
a breakdown.
tIMPORTANT t
Only use in case of engine fail-
ure or failure of the electrical
system.
• If the operator should fall ill or find himself incapable of
manoeuvring, the person on the ground can take over the basket
controls by following the instructions:
- Switch and hold the switch 5 in position A.
- Lower the basket using the ground controls.
tIMPORTANT t
Pay attention to any constructions or objects that may be
under the basket.
tIMPORTANT t
Never change the steering mode whilst driving.
• This pin must be used to stop the
turntable rotating when the platform
is being transported by truck or other
means of transport (train, etc.).
tIMPORTANT t
Do not forget to remove the turn-
table rotation blocking pin when
using the platform.
tIMPORTANT t
Never stand or work in the vicinity
of any electrical sources.
DIAGRAM STEERING MODE SELECTION
• 4-WHEEL DRIVE steering mode: Front and rear steering
wheels in opposite directions.
• 2-WHEEL DRIVE steering mode: Front steering wheels.
• CRAB steering mode: Front and rear steering wheels in
the same direction.
GENERAL INSPECTION CHECK THE FUEL LEVEL CHECK THE ENGINE OIL LEVEL CHECK THE COOLANT LEVEL CHECK THE HYDRAULIC FLUID
LEVEL CHECK THE PLATFORM CONTROLS
DAILY MAINTENANCE