Marcy MWB-1282 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MWB-1282
Retain This
Manual for
Reference
160825
OWNER'S
MANUAL
MARCY PLATINUM
SMITH MACHINE
MWB-1282

TABLE OF CONTENTS
BEFORE YOU BEGIN......................................................................................1
IMPORTANT SAFETY NOTICES.....................................................................2
SMITH MACHINE HARDWARE PACK……….....….......................................... 4
SMITH MACHINE ASSEMBLY INSTRUCTIONS...............................................6
SMITH MACHINE EXPLODED DIAGRAM........................................................15
SMITH MACHINE PARTS LIST…………………………………………………… 16
BENCH HARDWARE PACK……….....…..................................................…….17
BENCH ASSEMBLY INSTRUCTIONS......................................................…….19
BENCH EXPLODED DIAGRAM...............................................................……. 24
BENCH PARTS LIST……………………………………………………………….. 25
WARRANTY.................................................................................................… 26
ORDERING PARTS......................................................................................... 26
BEFORE YOU BEGIN
Thank you for selecting the Marcy PLATINUM SMITH MACHINE MWB-
1282. For your safety and benefit, read this manual carefully before using
the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there
are missing or damaged parts, we guarantee you complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays,
please call our after-sales department. Monday to Friday 8am to 5pm
GMT.
Pure-Tec Limited
Tel: [phone]
Monday - Friday 0800 – 1700 GMT
www.puretecfitness.com
Email: [e-mail]

1
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts and Guide Rods with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 135kgs.
5. Maximum weight on the Sliding Weight Post: 135kgs.
6. Maximum weight on Leg Developer: 45kgs.
7. Maximum weight on Weight Bar: 135kgs.
8. Maximum weight Capacity: 270kgs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR DOCTOR. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER
THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS.
READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. PURE-
TEC LIMITED ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR
PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS
PRODUCT.

SAVE THESE INSTRUCTIONS. 2
WARNING LABEL PLACEMENT

3
SMITH MACHINE HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

4
CAGE MACHINE HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

5
SMITH MACHINE ASSEMBLY INSTRUCTION
Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended that two or more people assemble this machine
to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Note: Do not tighten the Nuts and Bolts until instructed to do so.
B.) Connect the two Base Frames (#3) by the Cross Brace (#7). Secure each end of the
Cross Brace to each Base Frame with four M10 x 2 3/8” Carriage Bolts (#50), one 4 ¾”
x 3 ¼” Bracket (#22), four Ø ¾” Washers (#57), and four M10 Aircraft Nuts (#58).
C.) Attach the Left Rear Support (#5) onto the left Base Frame. Secure it with two M10 x 3
½” Allen Bolts (#55), four Ø ¾” Washers (#57), and two M10 Aircraft Nuts (#58).
Repeat the same step to install the Right Rear Support (#6) onto the other Base Frame.
DIAGRAM 1
6

STEP 2 (See Diagram 2)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach the Left Upright Beam (#1) to the Left Rear Support (#5) and onto the left
Base Frame (#3).
C.)Secure it to the Base Frame with two M10 x 4” Allen Bolts (#54), four Ø ¾”
Washers (#57), and two M10 Aircraft Nuts (#58).
D.)Secure it to the Left Rear Support with one M10 x 4” Carriage Bolt (#48), one Ø
¾” Washer (#57), and one M10 Aircraft Nut (#58) from side. Secure with one M10
x 5/8” Allen Bolt (#63) and one Ø ¾” Washer (#57) from top.
E.) Repeat A to D to install the Right Upright Beam (#6) to the right Base Frame.
F.) Attach the Top Beam (#4) to the Left & Right Upright Beam. Secure each end of
the Top Beam to each Upright Beam with one 4” x 2 3/8” Curved Bracket (#23),
one M10 x 4 1/8” Allen Bolt (#53) and one Ø ¾” Washer (#57) to the upper hole,
one M10 x 4 1/8” Carriage Bolt (#49), one Ø ¾” Washers (#57), and one M10
Aircraft Nut (#58) to the lower hole.
G.)Slide Lower Left Safety Stop Frame (#9) onto a Guide Rod (#11). Slide one Safety
Stop Frame (#18) onto the Guide Rod. Insert the bottom of the Guide Rod into the
hole on the left Base Frame. Attach the top of the Guide Rod to the bracket on
Left Upright Beam. Secure each end of Guide Rod with one M10 x ¾” (#56) and
one Ø ¾” Washer (#57). Repeat the same step to install the Lower Right Safety
Stop Frame (#10), the other Safety Stop Frame, and the other Guide Rod to the
other side.
H.)Turn and attach the hooks on the Lower Left & Right Safety Stop Frame to the
selected slot on Left & Right Upright Beam (#1 & #2).
7

DIAGRAM 2
8

STEP 3 (See Diagram 3)
A.) Attach two Ø 2 3/8” x 2” Rubber Bumpers (#30) to the holes on the Cross Brace (#7). Insert
the two Rear Short Guide Rods (#17) through the two Rubber Bumpers into the holes on
Cross Brace.
B.) Secure each Guide Rod to the Cross Brace with one M10 x ¾” Allen Bolt (#56) and one Ø
¾” Washer (#57) from bottom.
C.)Slide the Sliding Weight Post (#16) onto the two Rear Short Guide Rods. Make sure the
Pulley bracket on the Weight Sliding Frame faces upward.
D.)Attach the Rear Upper Frame (#15) to the two Rear Short Guide Rods. Secure each Guide
Rod to the Rear Upper Frame with one M10 x ¾” Allen Bolt (#56) and one Ø ¾” Washer
(#57).
E.) Attach the front of Rear Upper Frame to the Top Beam (#4). Attach the Front Upper Frame
(#14) to the Top Beam from front. Align the holes. Secure them together with two M10 x 2
¾” Carriage Bolts (#47), two Ø ¾” Washers (#57), and two M10 Aircraft Nuts (#58).
F.) Securely tighten all Nuts and Bolts installed in Step-1, Step-2, and Step-3.
9

DIAGRAM 3
10

CABLE LOOP DIAGRAM
11

STEP 4 (See Diagram 4 & Cable Loop Diagram)
A.) Attach the 170” Upper Cable (#25) to the opening on the Front Upper Frame (#14).
B.) Attach a Pulley (#33) to the opening. Secure it with one M10 x 4” Allen Bolt (#54), two
Ø ¾” Washers (#57), and one M10 Aircraft Nut (#58).
C.) Draw the Cable over the Pulley toward the back of the machine. Note: The Ball
stopper on the Cable needs to be under the Frame.
D.) Draw the Cable to the first opening on the Rear Upper Frame. Repeat B to install a
Pulley.
E.) Draw the Cable around the Pulley then downward to the open Pulley bracket on the
Sliding Weight Post (#16).
F.) Attach a Small Pulley (#32) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt
(#52), two Ø ¾” Washers (#57), and one M10 Aircraft Nut (#58).
G.) Draw the Cable around the Pulley then upward to the rear opening on the Rear Upper
Frame. Repeat B to install a Pulley.
H.) Draw the Cable around the Pulley and let the Cable hanging just for now.
I.) Connect the Lat Bar (#21) to the ball stopper on the Cable with two Hooks (#36) and
one 10-link Chain (#43).
12

STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach the 62” Lower Cable (#26) to the open bracket on the Cross Brace (#7). Attach
a Pulley (#33) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#52), two Ø ¾”
Washers (#57), one L-shaped Cable Retainer (#24), and one M10 Aircraft Nut (#58).
B.) Draw the Cable underneath the Pulley then upward to the 170” Upper Cable (#25)
installed in Step-4.
C.)Connect the Lower Cable to a Hook (#36). Connect the Hook to the 5-link Chain (#44).
Secure the 5-link Chain to the end of Upper Cable with one M10 x 1” Allen Bolt (#51),
two Ø ¾” Washers (#57, and one M10 Aircraft Nut (#58). Adjust the tension of the
Cable system by moving the Hook position to the Chain. If the tension is too loose then
move the hook up the chain. If the tension is too tight then move down the Hook.
D.)Connect the Shiver Bar (#21) to the ball stopper on Lower Cable with two Hooks (#36)
and one 15-link Chain (#42).
13

STEP 6 (See Diagram 6)
A.) Place the Lifting Sleeve (#8) in between the two Safety Stop Frames (#18). Align the
holes. Insert the Weight Bar (#13) from outside of one Safety Stop Frame through the
Lifting Sleeve to the other Safety Stop Frame on the other side.
B.) Turn and attach the two safety catch hooks on the Lifting Sleeve (#8) to the selected slots
on the Left and Right Uptight Beams (#1 & #2).
C.) Attach two Weight Bar Sleeves (#35) onto the Weight Bar from both ends. Attach two
Spring Clips (#62) to the Sleeves.
D.) Attach four Weight Posts (#12) into the holes on Left & Right Rear Support (#5 & #6).
Secure each Weight Post to the Support with one M10 x ¾” Allen Bolt (#56) and one Ø ¾”
Washer (#57). Slide four Olympic Sleeves (#34) to the four Weight Posts. Attach four
Spring Clips to the Sleeves.
14

SMITH MACHINE EXPLODED DIAGRAM
15

SMITH MACHINE PART LIST
KEY NO. DESCRIPTION Q’ty
1 Left Upright Beam 1 51 M10 x 1” Allen Bolt 1
2 Right Upright Beam 1 52 M10 x 1 ¾” Allen Bolt 2
3 Base Frame 2 53 M10 x 4 1/8” Allen Bolt 2
4 Top Beam 1 54 M10 x 4” Allen Bolt 7
5 Left Rear Support 1 55 M10 x 3 ½” Allen Bolt 4
6 Right Rear Support 1 56 M10 x ¾” Allen Bolt 12
7 Cross Brace 1 57 Ø ¾” Washer 58
8 Lifting Sleeve 1 58 M10 Aircraft Nut 28
9 Lower Left Safety Stop Frame 1 59 ST3.8 Philips Screw 24
10 Lower Right Safety Stop Frame 1 60 Rivet 8
11 Guide Rod 2 61 M8 x 3/8” Allen Bolt 2
12 Weight Post 4 62 Spring Clip 8
13 Weight Bar 1 63 M10 x 5/8” Allen Bolt 2
14 Front Upper Frame 1 64 Ø 7/8” x ¾” End Cap 18
15 Rear Upper Frame 1 65 Ø 5/8” End Cap 18
16 Sliding Weight Post 1 66 Ø ¾ End Cap 2
17 Rear Short Guide Rod 2
18 Safety Stop Frame 2
19 Lat Bar 1
20 Shiver Bar 1
21 Rotate Ring 2
22 4 ¾” x 3 ¼” Bracket 2
23 4” x 2 3/8” Curved Bracket 2
24 L-shaped Cable Retainer 1
25 170” Upper Cable 1
26 62” Lower Cable 1
27 Ø 3 ½” Upright Beam End Cap 2
28 1 5/8” x 3 1/8” End Cap 4
29 Ø 3” Upper Frame End Cap 2
30 Ø 2 3/8” x 2” Rubber Bumper 2
31 ؾ” x 2” Cover 2
32 Small Pulley 1
33 Pulley 4
34 Olympic Sleeve 6
35 Weight Bar Sleeve 2
36 Hook 5
37 Ø 1” End Cap 8
38 Ø 1 ¾” End Cap 2
39 Plastic Ring 8
40 Ankle Strap 1
41 Single Handle 1
42 15-link Chain 1
43 10-link Chain 1
44 5-link Chain 1
45 6” Grip 4
46 Sliding Sleeve 12
47 M10 x 2 ¾” Carriage Bolt 2
48 M10 x 4” Carriage Bolt 2
49 M10 x 4 1/8” Carriage Bolt 2
50 M10 x 2 3/8” Carriage Bolt 8
16

BENCH HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

17
BENCH HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

18
BENCH ASSEMBLY INSTRUCTION
STEP 1 (See Diagram 1)
A.) Attach the Bench Base Frame (#6) to the Rear Stabilizer (#7). Secure the side-holes
with two M10 x 4” Carriage Bolts (#41), two Ø ¾” Washers (#31), and two M10 Aircraft
Nuts (#33). Secure the top hole with one M10 x 5/8” Allen Bolt (#36) and one Ø ¾”
Washer (#31).
B.) Attach the Wheel Set (#25) to the bracket on Rear Stabilizer. Secure it with one M8 x
5 1/8” Allen Bolt (#35), two Ø 5/8” Washers (#30), and one M8 Aircraft Nut (#32)
DIAGRAM 1
19