Marcy MD-440 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MD-440
Retain This
Manual for
Reference
07-23-05
OWNER'S
MANUAL
MARCY DIAMOND ELITE
UTILITY BENCH
MD-440
Escalade International Limited
Pleasant Road, Penllergaer, Swansea. SA4 9GE
Tel: [phone] Fax [phone]
www.escaladesports.co.uk
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICES..................................................................... 2
HARDWARE PACK……….....…....................................................................... 4
ASSEMBLY INSTRUCTIONS........................................................................... 6
EXPLODED DIAGRAM.........................................................................………. 10
PARTS LIST…………………………………………………………………………. 11
WARRANTY.................................................................................................… 12
ORDERING PARTS......................................................................................... 12
BEFORE YOU BEGIN
Thank you for selecting the MARCY DIAMOND ELITE UTILITY BENCH MD-440 by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using
the machine. As the distributor, we are committed to provide you complete customer
satisfaction. If you have any questions, or find there are missing or damaged parts or you
require assistance assembling this product, we guarantee you complete satisfaction
through direct assistance. To avoid unnecessary delays, please call our customer service
department Monday to Friday 9am to 5pm.
Tel [phone]
E mail: [email protected]
Supplied by
Escalade International Ltd
Pleasant Road
Penllergaer
Swansea
SA4 9GE
Tel: [phone]
Fax: [phone]
www.escaladesports.co.uk
E mail: [email protected]
1

IMPORTANT SAFETY PRECAUTIONS
This bench is built for optimum safety. However, certain precautions apply whenever you operate a
piece of exercise equipment. Be sure to read the entire manual before you assemble or use your
bench. In particular, note the following safety precautions:
1. Keep children and pets away from the bench at all times. Do not leave children unattended in
the same room with the bench. The bench is not a toy and therefore parents and guardians
should be aware of the natural tendency for children to play, leading to situations and behaviour
for which the bench is not intended.
2. If children are allowed to use the bench their physical/mental development and above all,
temperament should be taken into account. Constant supervision is therefore needed.
3. Only one person at a time should use the bench.
4. If the user experiences dizziness, nausea, chest pain or any other abnormal symptoms, STOP
the workout at once. Consult a physician immediately. Injuries may occur due to incorrect or
excessive exercise.
5. Position the bench on a clear levelled surface which is clear of all obstacles as not to restrict
movement whilst exercising. DO NOT use the bench near water or outdoors.
6. Keep hands away from all moving parts
7. Always wear appropriate clothing when exercising. DO NOT wear robes or other clothing that
could become caught in the bench. Running or aerobic shoes are also required when using the
bench.
8. Use the bench only for its intended use as described in this manual. DO NOT use attachments
not recommended by the manufacturer.
9. Do not place any sharp objects around the bench
10. Disabled persons should not use the machine without a qualified person or physician in
attendance.
11. Before using the bench to exercise, always do stretching exercises to properly warm up.
12. Never use the bench if it is not functioning properly.
13. This product is intended for H=Domestic use only.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35
OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS
BEFORE USING ANY FITNESS EQUIPMENT. MARCY ASSUMES NO RESPONSIBILITY
FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE
USE OF THIS PRODUCT.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
3. Maximum User’s Weight: 140 kgs.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL
3

HARDWARE PACK
4

HARDWARE PACK
5

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended this machine be assembled by two or
more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Main Frame (#1) onto the Front & Rear Stabilizers (#2 & 6). Secure each end
with two M10 x ¾” Allen Bolts (#32) and ∅¾” Washers (#39).
DIAGRAM 1
6

STEP 2 (See Diagram 2)
A.) Attach the Backrest Supports (#3) to the pivot on the Main Frame (#1). Secure it with
one M12 x 5 ¾” Allen Bolt (#31), two Ø1” Washers (#38), and one M12 Aircraft Nut
(#36). Do not over tighten the Nut and Bolt, make sure the Backrest Supports are able
to swivel.
B.) Attach the Backrest Incline Support (#4) in between the Backrest Supports (#3). Secure
it with one M12 x 5 ¾” Allen Bolt (#31), two Ø1” Washers (#38), and one M12 Aircraft
Nut (#36). Attach the other end of Backrest Incline Support to the selected slot on the
Main Frame to obtain the desired backrest incline position.
C.)Place the Backrest Board (#12) onto the Backrest Supports. Secure it with four M8 x 1
5/8” Allen Bolts (#34) and Ø 5/8” Washers (#40).
D.)Place the Seat (#11) onto the Main Frame. Secure it with four M8 x 1 5/8” Allen Bolts
(#34) and Ø 5/8” Washers (#40).
7

STEP 3 (See Diagram 3)
A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it
with one Axle (#42), two M10 x 5/8” Allen Bolts (#30), and two Ø ¾” Washers (#39). Do
not over tighten the Bolts, make sure the Leg Developer is able to swivel.
B.) Insert the U-shaped Pin (#10) into the tube in front of the Main Frame. Secure it with
one Spring (#29), Ø ½” Washer (#28), and M6 x 5/8” Philips Screw (#41).
C.)Insert three Foam Tubes (#9) halfway through the holes on the Main Frame and Leg
Developer. Push six Foam Rolls (#26) onto the Tubes from both ends. Plug six Foam
Roll End Caps (#21) into the Tubes from both ends.
D.)Attach the Curl Bar Handle Support (#45) to the bracket on the Leg Developer. Secure it
with a L-shaped Pin (#27).
E.) Attach an Olympic Sleeve (#14) onto the weight post on Leg Developer. Attach a Spring
Clip (#15) to the Sleeve. DIAGRAM 3
8

STEP 4 (See Diagram 4)
A.) Attach the Arm Curl Pad (#13) to the Arm Curl Stand (#7). Secure it with two M8 x
¾” Allen Bolts (#33) and Ø 5/8” Washers (#40).
B.) Insert the Arm Curl Stand into the front opening on the Main Frame. Use a Lock
Knob (#16) to secure the Stand at desired height.
C.)The Leg Developer can be locked when doing sit up exercise. Simply pull the U-
shaped Pin (#10) out and drop into the hole on the Leg Developer. Remove the Pin
when doing Leg Developer exercises.
D.)Remove the Arm Curl Stand and Curl Bar Handle when using Leg Developer.
DIAGRAM 4
9

10

PARTS LIST
KEY NO. DESCRIPTION Q’ty
1 Main Frame 1
2 Front Stabilizer 1
3 Backrest Support 2
4 Backrest Incline Support 1
5 Leg Developer 1
6 Rear Stabilizer 1
7 Arm Curl Stand 1
8 Curl Bar 1
9 Foam Tube 3
10 U-shaped Pin 1
11 Seat 1
12 Backrest Board 1
13 Arm Curl Pad 1
14 Olympic Sleeve 1
15 Spring Clip 1
16 Lock Knob 1
17 2 3/8” x 1 5/8” End Cap 2
18 1” Square End Cap 2
19 Ø 1” Cone-shaped End Cap 1
20 Ø 1” End Cap 1
21 Foam Roll End Cap 6
22 Ø 2 3/8” Bushing 2
23 Sleeve 1
24 Stabilizer End Cap 4
25 Rubber Bumper 1
26 Foam Roll 6
27 L-shaped Pin 1
28 Ø ½” Washer 1
29 Spring 1
30 M10 x 5/8” Allen Bolt 2
31 M12 x 5 ¾” Allen Bolt 2
32 M10 x ¾” Allen Bolt 4
33 M8 x ¾” Allen Bolt 2
34 M8 x 1 5/8” Allen Bolt 8
35 M6 x ½” Philips Screw 1
36 M12 Aircraft Nut 2
37 Ø 1 ½” Bushing 2
38 Ø 1” Washer 4
39 Ø ¾” Washer 6
40 Ø 5/8” Washer 10
41 M6 x 5/8” Philips Screw 1
42 Axle 1
43 Curl Bar Handle Grip 2
44 Ø ¾” Bushing 2
45 Curl Bar Handle Support 1
11

LIMITED WARRANTY
Escalade warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the frame and one year on all
other parts and components from the date of purchase. This warranty extends only to the
original purchaser. Escalade’s obligation under this Warranty is limited to replacing damaged
or faulty parts at Escalade’s option.
All returns must be pre-authorised by Escalade. This warranty does not extend to any product
or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage, purchasers own repairs or for products used for commercial or rental
purposes. No other warranty beyond that specifically set forth above is authorized by Escalade.
Escalade is not responsible or liable for indirect, special or consequential damages arising out
of or in connection with the use or performance of the product or other damages with respect to
any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs
of removal, installation or other consequential damages or whatsoever natures.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and
duration to the terms set forth herein.
Your statutory rights are not affected.
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department Monday to
Friday 9am to 5pm. Tel: [phone]
E mail: [email protected]
When ordering replacement parts, please give the following information.
1. Model
2. Description of Parts
3. Part Number
4. Date of Purchase
12

CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-
abrasive detergent. DO NOT use solvents.
3. Failure to examine the BENCH regularly may affect the safety
level of the equipment.