Markilux 990 User manual

7061396
Cassette-folding arm-awning
markilux 990
Mounting instructions
1
1
9/01/10
1. Overview
1 Pro ection pro-
file
2 Folding arm
3 Fabric
4 Console
5 Cassette
6 Covering cap
7 Wall bracket
2. Mounting brackets
2.1 Overview mounting brackets
Wall bracket Ceiling bracket Rafter holder
71624. 71625.
71612.
Supplementary bracket for
Rafter holder
75383.
Further mounting brackets can be found in the sales information!
2.2 Mounting area for mounting brackets

2
2 Folding arms
M = Awning width
MB = Mounting area bracket (concentric bracket depending on size)
HT = bracket
Di-
mensions in cm
3. Mounting systems
Attention!:
Basically the following is applicable for all mounting systems:
1. The mounting material manufacturers (e.g. Fischer, Hilti, Upat, etc. offer different mounting systems
according to the undersurface. The corresponding withdrawal and/or shearing forces from our sales
documents have to be taken into consideration. If the conditions for the mounting are met according to
DIN EN 13561, the wind resistance class 2 for the mounting can be confirmed to the user.
2. Mounting material is not supplied automatically, as different subsurfaces (e.g. concrete, lime sand
stone, autoclaved aerated concrete etc require different types of mounting material.
3. IMPORTANT: Mounting brackets have to be aligned with each other! When subsurfaces are uneven, the
clearances are to be checked using a cord pulley and if required compensated accordingly. Due to the
horizontal mounting of the folding-arm awning and the perpendicular fit of the mounting brackets, the
smooth functioning of the folding-arm awning is guaranteed.
3.1 Wall mount
Measurements in
mm
1. Determine mounting height. Mark position of
brackets (see also adjusting range at bracket .
2. Consider mounting material and type of mount-
ing according to undersurface (mounting plate
A or B .
3. Mark the drilled holes and mount the mounting
brackets with the corresponding mounting plate
according to the undersurface. Align the mount-
ing brackets horizontally!

3
Mounting area of wall brackets
VB = ad usting range
M = width of awning Dimen-
sions in mm
Mounting plate A
Dimensions in
mm
Mounting plate B
Measurements
in mm

4
3.2 Ceiling mount
Dimensions in
mm
1. The mounting takes place in relation to the wall
fitting. The shifting area (VB for the ceiling
brackets is like for the wall mount.
Attention!: Should the angle of inclination be
greater than 46° to the horizontal line, an ac-
cessible area of 60 cm has to be available for
manual operation behind the awning. There are
no limitations for motor-driven installations.

5
3.3 Rafter mount
Dimensions in
mm
With supplementary bracket:
Measurements in
mm
1. The mounting takes place in relation to the wall
fitting. The shifting area (VB for the rafter
brackets is like for the wall mount.
2. Determine mounting height. Hold rafter bracket
and mark. Fix the rafter bracket with a nail.
Align the brackets horizontally using a spirit
level and fix a second nail.
3. Drill through the roof rafter at the screw holes.
Screw the bracket with suitable mounting mate-
rial. Align the roof rafter brackets horizontally.

6
4. Hanging up the awning (e.g. wall fitting)
1. Lay the awning (1 on the wall
bracket (2 .
Attention!: Awning has to be
retracted completely (delivery
state !
2. Hang the awning (1 in such a
way into the wall brackets (2 that
the consoles (3 lie flush at the
top on the wall brackets and the
threaded pins SW 5 (4 can be
screwed in.
3. Always tighten first the two
threaded pins SW 5 (4 of the left
console and then the ones of the
right console!
L Left
4. Attention!: When tightening
the threaded pins, no gap must
form at the top in the connection
area between console and
bracket (see drawing !

7
5. Setting the angle of inclination
5.1 Wall mount 0° - 35°
1. Extend awning and unscrew
the rear threaded pin SW 5 (1 at
both consoles by approx. 10 mm
from the consoles.
2. Set the required inclination by
turning the front threaded pin SW
6 (2 either way at both consoles
respectively. While doing this take
the pressure of the arms by lifting
them.
3. Attention!: Tighten the rear
threaded pin SW 5 (1 again at
both consoles so that the awning
is protected against flipping up!
5.2 Ceiling mount 0° - 35°
1. Extend awning and unscrew
the rear threaded pin SW 5 (1 at
both consoles by approx. 10 mm
from the consoles.
2. Set the required inclination by
turning the front threaded pin SW
6 (2 either way at each of the
two consoles. While doing this
take the pressure of the folding
arms by lifting them.
3. If an angle of 35° is sufficient
for both consoles, tighten the
rear threaded pin SW 5 (1 again
so that the awning is protected
against flipping up!

8
5.3 Ceiling-/ Rafter mount 36° - 70°
1. Extend awning and unscrew
the rear threaded pin SW 5 (1 at
both consoles by approx. 10 mm
from the consoles.
2. Screw the front threaded pin
SW 6 (2 at both consoles in the
middle threaded drilling (3 .
While doing this take the pressure
of the arms by lifting them.
3. Set the required inclination by
turning the threaded pin SW 6 (2
either way at each of the two
consoles. While doing this take
the pressure of the arms by lifting
them.
4. Attention!: Tighten the
rear threaded pin SW 5 (1 again
at both consoles so that the
awning is protected against
flipping up!
6. Arm position at retracted awning
1. If an arm is set too high or too low when the awning is retracted
and therefore the projection profile does not close properly, the arm
position is to be corrected.
2. Retract the projection profile
(1 that much that the security
threaded pin SW 3 (2 can still be
loosened. Loosen security
threaded pin.

9
3. The articulated arm can be
raised and/or lowered by turning
the eccentric bolt (3 .
4. Attention!: Align the
articulated arms in such a way
that they do not hit the upper (4
or lower edge (5 of the
projection profile!
5. Secure the eccentric bolt (3
with the threaded pin (2 . Check
the new setting of the articulated
arms by retraction and extension
of the awning.
7. Pro ection profile does not close properly
1. If the projection profile does
not close properly with the cas-
ing, a gap might form on top (1
or below (2 a gap between the
top casing cover and the casing.
The front profile closing angle at
the projection profile can be cor-
rected.
2. Extend the awing completely
until the fabric is without tension.
Pull off the covering cap of the
projection profile bracket (3 and
mark the position of the projec-
tion profile bracket (4 using a
soft pencil.
3. Loosen the hexagonal nuts
SW10 (5 .
4. Align the projection profile (6 5. Align the projection profile
bracket (4 at the mark, then
tighten the hexagonal nuts SW 10
(5 .

10
8. Motor-driven awning
8.1 Motor connection
The electrical connection for the motor drive and/or control system connection is to be carried out accord-
ing to the instructions of the manufacturer of the motor and control system. Modifications, especially in
the motor's, the control system's and the connecting cable's area require a written permit.
The installation and setting instructions are indicated on the motor's power supply cable. Instructions for
further electrical components are to be found in the corresponding packaging.
Attention!:
The built-in motor has a set end stop both in the extension and retraction direction. These settings were
effected in the factory. They always have to be checked on site, as the end stops might have shifted e.g.
through strong vibrations during transport or the motor does not switch off anymore. For any changes or
corrections of these settings please refer to the instructions of the motor.
Sense of rotation during retraction
Attention!:
The rolling up of the fabric on the fabric roller
from below during retraction could lead to damage
to the awning. When changing the end stop, it is
indispensable to pay attention to the sense of rota-
tion!
8.2 Motor connection data markilux 990

with radio control (433 MHz :
U = 230 V ~ / 240 W, 50 Hz,
I = 1.10 A
without radio control:
U = 230 V ~ / 240 W, 50 Hz,
I = 1.10 A
9. Rainwater gutter and water discharge
In order to guarantee a safe water discharge from
the rainwater gutter, the inclination angle can be
set differently for both consoles (see point 4 . Like
this the projection profile shows a slight incline.