MarMonix MIB-393 User manual

Non-Contact Forehead Infrared Thermometer
Products Code: MIB-393
User Manual
WWW.MARMONIX.CO

Contents
1. General Description
2. Safety Information
3. Features
4. Intended Use
5. Configuration
6. Indicator
7. Description of Symbols
8. Technical Specifications
9. Advice for The 1st Use
10. Use
11. Measuring Operation
12. Advice
13. Maintenance and Cleaning
14. Troubleshooting
15. This Appliance Conforms to the Following Standards

1. General Description
Non-Contact Forehead IR Thermometer is specially
designed to take the body temperature of a person
regardless of room temperature. Depending on
various skin types and thickness, there may be
temperature difference.
2. Safety Information
 This device must only be used for the purpose
described in this instruction manual
 This device must only be used in an ambient
temperature range between 10 to 40˚C
 Do not expose this thermometer to extreme
temperature to electric shocks
 Do not expose this thermometer to extreme
temperature conditions of >50˚C or <0˚C
 Do not use the device in relative humidity higher
than 85%
 Do not use the device near large electromagnetic
fields such as found with cordless or cell phones
 Keep the device away from water and heat,
including direct sunlight
 Do not drop or knock the device, and do not use if
damaged

 It may affect the accuracy of measurements when
the forehead is covered by hair, perspiration, cap or
scarf(see part 10-4)
 When the body infrared thermometer should be left
in that room during 15 to 20 minutes before using
 Keep the measuring distance as 5cm-15cm(2in-
5.9in)(see part 10-4)
 When the body infrared thermometer should be left
in that room during 15 to 20 minutes before using
 It may affect the accuracy measurements when the
forehead is covered by perspiration or other factors,
please take the temperature behind the ear
lobe(see part 10-5)
 Clean the glass with a cotton bud lightly moistened
with 70% alcohol.
Importance:
 Before taking of the temperature make sure to
remove hair and perspiration from the forehead.
 Selecting “Body” mode to measure the body
temperature; Selecting “Surface” mode to measure
the surface temperature.
 Use of this thermometer is not intended as a
substitute for consultation with your physician.
 Should a problem occur with your device, please
contact your retailer.

Do not attempt to repair the device yourself.
 According to EMC standard, the medical electronic
products should be maintained specially.
3. Features
 Precise non-contact measurements
 User selectable ˚C or ˚F
 Selectable body and surface temp
 Set alarm value
 Memorization of the last 32 measurements
 Automatic Data Hold & Auto power off
 Automatic selection range and display resolution
0.1˚C(0.1˚F)
 Backlight LCD display
 Intended Use
Non-Contact Forehead IR Thermometer is designed
for body surface and forehead temperature
measurement for infants and adults without contact
to human body.
Non-Contact Forehead IR Thermometer can also be
used to measure the temperature of a baby-bottle or
bath, or room temperature (by using the surface
temp function)
Normal Temperatures According To measurement
Method

Measurement Method Normal Temp ˚C Normal Temp ˚F
Rectal 36.6 to 38 97.8 to 100.4
Oral 35.5 to 37.5 95.9 to 99.5
Axillary 34.7 to 37.3 94.4 to 99.1
ear 35.8 to 38 96.4 to 100.4
The temperature of the human body varies
throughout the day. It can also be influenced by
numerous extra factors: age, sex, type and thickness
of skin …
Normal Temperature According to Age
Age
Temp ˚C
Temp ˚F
0-2 years
36.4 to 38.0
97.5 to 100.4
3-10 years
36.1 to 37.8
97.0 to 100.0
11-56 years
35.9 to 37.6
96.6 to 99.7
>65 years
35.8 to 37.5
96.4 to 99.5

4. Configuration
1- IR Sensor
2- LCD Display
3- Mode Selection
4- Down Button
5- Up Button
6- Mode Button
7- Measurement Trigger
8- Battery Cover

5. Indicator
1- Surface mode symbol
2- Body mode symbol
3- Digital readout
4- Battery symbol
5- The order readout
6- Save data readout
7- Temperature ˚C(Celsius) ˚F(Fahrenheit) scale
8- Buzzer symbol

1. Description of Symbols
The device is in accordance with
Medical Device Directive 93/42/EEC
The device is in accordance with FCC
Part 15 Subpart B:2007/Radio
Frequency Device IC Regulation
ICEC-003: 2004 Interference-causing
Equipment Standard-Digital
Apparatus
3V DC power supply
Type B equipment
In order to protect the environment,
please recycle the battery according
to the local regulations
Body Surface
Indication of Mode
Attention, consult accompanying documents

6. Technical Specifications
Normal Conditions of Use
Display resolution 0.1˚C(0.1˚F)
Operating temperature
10 to 40˚C(50 to
104˚F)
Storage temperature
0 to 50˚C(32 to
122˚F)
Humidity rate ≤85%
Power
DC 3V (2x “AA”
batteries)
Size
149x77x43 mm/
5.9x3x1.7 in (LxWxH)
Weight
Gross 400g/ Net
172g
Measuring Range
In Body Mode
32.0 to 42.5˚C (90 to
108˚F)
In surface Temp Mod
0 to 60˚C (32 to 140˚F)
Accuracy
±0.3˚C(0.54˚F)
Measuring Distance
5 cm – 15 cm (2in – 5.9in)
Automatic Stop
7 sec

Non-contact Body Infrared
Thermometer Precision
32 to 35.9˚C/ 93.2 to
96.6˚F
±0.3˚C/
0.5˚F
According to
ASTM Standard
E1965-1998
(2003)
36 to 39˚C/ 96.8 to
102.2˚F
±0.2˚C/
0.4˚F
39 to 42.5˚/ 102.2 to
108.5˚F
±0.3˚C/
0.5˚F
7. Advice For The 1st Use
For stable and reliable results, it is essential to check the
Non-contact Body Infrared Thermometer and changes
as needed, as follows:
1st step: take the temperature of a person using a
conventional thermometer; you will get 37.5˚C (99.5˚F)
for instance.
2nd step: take the temperature of the same person using
the Non-contact Body Infrared Thermometer keeping
the 5 to 15cm (2in to 5.9in) distance between the
thermometer and forehead ( Take care to remove any
obstacle which could alter the measurement (hair,
perspiration …). If you get 37.5˚C (99.5˚F), the Non-
contact Body Infrared Thermometer is properly set and
ready for use.
If you get a lower temperature, 36.4˚C (97.4˚F) for
example, your difference is 1.1˚C (2.2˚F). you should
adjust the temperature on the Non-contact Body

Infrared Thermometer and add the difference, i.e.
1.1˚C(2.2˚F).
To do it, press the “MODE” button for 2 seconds, the
screen displays F1, press “MODE” button again until
you get F3. Press “UP” button in order to add the
difference (in our example, 1.1˚C – 2.2˚F).
3rd step: To check, take the temperature again using the
Non-contact Body Infrared Thermometer.
8. Use
10-1. Install battery
10-2. For the first use or when inserting new batteries
wait between 10 minutes for the warm-up of the
apparatus and when inserting the new batteries.
10-3. If the device is not used for a long time, once you
turn it on again, the device will test the room
temperature first and will delay turning on for one or
two seconds.

10-4. Aim towards the forehead (see the diagram below
for the positioning), from a distance of 5cm(2in), press
the measuring key, the temperature is displayed
immediately. Making sure there is no hair,
perspiration, cosmetic or cap covered on the forehead.
10-5. when the room temperature is significant
difference, or there is perspiration on the forehead,
you can take the temperature behind the ear lobe.
Making sure there is no hair, perspiration, cosmetic or
cp covered.

9. Measuring Operation
11-1. Choosing The Temperature Unit – F1 Function
Press “MODE” button for 2 seconds, the screen displays:
F1. Select “DOWN” for degrees Celsius, “UP” for
degrees Fahrenheit.
11-2. Alarm Setup – F2 Menu
Press “MODE” touch for 2 seconds, the screen displays:
F1. Press twice “MODE” touches to get F2. Select “UP”
to increase the threshold by 0.1˚C (0.1˚F), “DOWN” to
reduce it by 0.1˚C (0.1˚F).
Note: The alarm threshold default value is 38˚C (100.4˚F).
11-3. total difference – F3 Menu
To adjust the total variation of you’re the Non-contact
Body Infrared Thermometer.
Press “MODE” button for 2 seconds, the screen displays:
F1. Press “MODE” button two times to get F3. Select
“UP” to increase the difference by 0.1˚C (0.1˚F),

“DOWN” to reduce it by 0.1˚C (0.1˚F). In the cases of
seasonal or environmental changes a verification and
adjustment should be carried out.
Note: This function is only effective Body
11-4. Buzzer ON/OFF – F4(F3) Menu
Press “MODE” button for 2 seconds, the screen displays:
F1. Press three(two) times “MODE” button to get
F4(F3).
Select “UP” to open the buzzer ( a sound icon “ “ is
displayed on the LCD screen), press “DOWN” to stop it
( the icon disappear).
11-5. Exiting The Setting Mode
Press “MODE” button until the screen turns off.
11-6. The Non-contact Body Infrared Thermometer is
specially designed to take the body temperature of a
human being. For this, use the Body mode.
Measurement range for Body mode: 32 to 42.5˚C (86
to 108˚F)
You can also use the Non-contact Body Infrared
Thermometer to measure the temperature of an area
or an object, a food, a liquid or at room temperature.
For this, use the Surface mode. Measurement range
for Surface mode: 0 to 60˚C (32 to 140˚F)

Important: The area temperature differs from the internal
body temperature. To obtain the internal temperature
always use the Body mode.
Please make sure to select the Body mode for an internal
temperature reading and the Surface mode for an
external area reading (bottle, bath, room …).
11-7. Data Memory
Data memory automatically after temperature
measurements, which will display at the right corner of
LCD. Press “UP” or “DOWN” button to display the last
temperature measurement.
Under the condition of power off, press “UP” and
“DOWN” button together for two seconds, to display
the last temperature measurement. At this mode if
change the order number to 0 and press “MODE”
button, then delete all memory data.
11-8. Changing The Batteries
Display: when the LCD screen displays “ “ the battery
is used.
Operation: Open the lid and change the batteries, taking
great care with the correct positioning. A mistake with
this could cause damage to the apparatus and

compromise the guarantee of your Non-contact Body
Infrared Thermometer. Never use rechargeable
batteries. Use only batteries for single batteries.
Remove the battery from the instrument if it is not
required for extended periods of time in order to avoid
damage to the thermometer resulting from a leaking
battery.
11-9. Longevity Use
The Non-contact Body Infrared Thermometer was
conceived for an intense and professional use, it’s
longevity is guaranteed for 40000 takings.
10. Advice
 The protective glass over the lens is the most
important and fragile part of the thermometer, please
take great care of it.
 Do not recharge non rechargeable batteries, do not
throw in fire.
 Do not expose the thermometer to sunlight or water.
11. Maintenance and cleaning
 The Infrared Sensor is the most precise part, must be
protected carefully.
 Clean the device with a cotton bud lightly moistened
with 70% alcohol.
 Do not clean the device with corrosive detergent.

 Keep the device away from water or other liquid.
 Store the device in a dry environment, and keep it
away from dust and direct sunlight.
12. Troubleshooting
If you happen to have one of the following problems
while using you’re the non-contact forehead IR
thermometer please refer to this breakdown service
guide to help resolve the problem. If the problem
persists please contact our customer service.
The screen displays the body temperature inferior to
32˚C (89.6˚F)
If you’re on surface mode the 32˚C (89.6˚F) temperature
displayed is showing the external temperature that
your body releases.
The screen displays the message
“HI”
When using the Non-contact Body
Infrared Thermometer the
message HI can show on the
screen.
The analysis is above the measurement range selected,
either superior to 42.5˚C (108˚F) in Body mode or
superior to 60˚C (140˚F) in Surface mode.

The screen displays the message
“LO”
When using the Non-contact Body
Infrared Thermometer the
message Lo can show on the
screen.
The temperature analyzed is
under the measuring range
selected, either less than 32˚C (90˚F) in Body mode or
less than 0˚C (32˚F) in Surface mode.
This message displays in various cases – please find
below a list of the main cases.
Reasons for “LO” or “HI” message display
Advice
Temperature reading
hampered by hair,
perspiration …
Make sure there is no
obstruction prior to taking
a temperature.
Temperature hampered
by an hair flux
Make sure there is
no air flux as this could interfere with the infrared
system
The measuring distance
is too far
Please respect the
measuring distance
( between 5 to 15cm – 2
to 5.9in)
From high/low
temperature condition
to room temperature
Waiting for 10 minutes b
temperature

13. This appliance conforms to the following
standards:
 EN12470-5 and ASTM E1965-1998
 EN980: Graphical symbols for use in the labeling of
medical devices
 EN 1041: Information supplied by the manufacturer
with medical devices
 EN 60601-1: Medical electrical equipment Part 1:
General requirements for safety (IEC:60601-1:1998)
 EN 60601-1-2: Medical electrical equipment Part 1-2:
General requirements for safety Collateral standard
Electromagnetic compatibility Requirements and test
(IEC 60601-1-2:2001)
EMC Statement
This device has been tested and homologated in
accordance with EN60601-1-2:2007 for EMC. This does
not guarantee in any way that the device will not be
affected by electromagnetic interference. Avoid using
the device in high electromagnetic environment.
The MEDICAL DELECTRICAL EQUIPMENT needs special
precautions regarding EMC and needs to be installed and
put into service according to the EMC information
provided in the ACCOMPANYING DOCUMENTS.