Marport PRO DOCK User manual

1
Dock | Quick Reference Guide | V2
Purpose
Marport Dock provides a new way of charging Marport sensors. It allows the user to:
• Charge up to 4 sensors simultaneously.
• Quickly see the charging status of the sensor,
thanks to a visual display on the charger plugs and Dock screen.
• Have a full overview of the sensor eet:
which sensors are deployed, charging or on deck.
• Congure the sensor settings, since the Dock acts as
a gateway between the sensors and Mosa2 conguring soware.
• Be alerted when maintenance is needed on the sensors.
The Dock is compatible with the latest generation of Marport sensors, including the Marport Pro
range. It is compatible in a limited state with the previous generations of sensors.
Getting started
12 3
Charger Plug Summary
Pick me up Updating Maintenance
needed Warning
Charging green:
charged at > 90%
Charging orange:
charged at 70% to 90%
Charging red:
charged at <70% Conguring

2
Dock | Quick Reference Guide | V2
Overview of the Dock Screen
The Dock displays the following information when the latest generation of sensors are connected.
If previous generation sensors are connected, the screen only displays the level of charge.
Notications
If there is a status warning message, a warn-
ing icon appears.
Version number of the Dock rmware.
Node corresponding to the sensor location
on the trawl and its spare identier (A, B, C,
D). Background color becomes darker as the
level of charge increases.
Application of the sensor
Status of the sensor:
• Charging
• Ready to deploy
• Conguring
• Updating
The status can also display warning
messages. See Troubleshooting section
below for details.
Remaining battery life
Current level of charge.
Remaining time before the battery is fully
charged.
Indicates the following:
Ethernet connector is correctly
connected and gets an IP address.
USB connector is correctly
connected.
Conguration Cable is connected
to a sensor.
Appears if no sensor is connected on the port.
1
10
2
3
4
5
6
7
8
9
11

3
Dock | Quick Reference Guide | V2
Overview of the Virtual Charger Room
Node identifying the location of the sensor on the trawl.
Name of the application.
If any, number of spare sensors.
Charging level.
Access to the settings.
Remaining lifetime at the current state of charge.
Sensor status
Open Scala2 application, then click Menu > Virtual Charger Room.
The sensor is connected to the
Dock and charging. It displays
Ready to deploy when fully
charged.
Click > to display a
visual animation on the charger
plug when the sensor must be
deployed.
The sensor is operating on the
trawl.
The sensor is out of water and is
not connected to the Dock.
Interface with Mosa2
Dock connected by Ethernet
to the vessel’s network.
: Click to make the LED
strip above the Ethernet
connector ash blue for 30
seconds.
Sensor connected to the
Dock with a charger plug.
: click to show the
deploy animation on the
charger plug for 30 seconds.
Click Menu > Expert Mode to
display the Dock on the discovery
page.
7
6
5
4
3
2
1
1
2

4
Dock | Quick Reference Guide | V2
© 2022 Marport. All Rights reserved.
No part of this document may be reproduced, stored in a retrieval system or transmitted in any form by any means; electronic, mechanical,
photocopying or otherwise, without the express written permission from Marport. “Marport”, the Marport logo and Soware Dened Sonar are
registered trademarks of Marport. All other brands, products and company names mentioned are the trademark and property of its respective owners
only. Marport is a division of Airmar Technology Corporation.
Iceland
Marport EHF
Fossaleyni 16
112 Reykjavík, Iceland
[email protected]om
South Africa
Marport South Africa
Cape Town, Western Cape,
11 Paarden Eiland Road,
Paarden Eiland, 7405
[email protected]om
France
Marport France SAS
8, rue Maurice Le Léon
56100 Lorient, France
[e-mail]
Norway
Marport Norge A/S
Breivika Industrivei 69,
6018 Ålesund, Norway
[email protected]
USA
Marport Americas Inc. USA
12123 Harbour Reach Drive
Mukilteo, WA 98275 USA
[email protected]
Spain
Marport Spain SRL
Camino Chouzo 1
36208 Vigo (Pontevedra) Spain
[e-mail]
Troubleshooting
Offices
Warning messages on the Dock screen
Status message Description
Warning - Clean sensor
endcap
The sensor cannot connect to the Dock because the
shoulder bolts are dirty or damaged:
• Clean them using a swab or Q-tip with Isopropyl
alcohol.
• Fully clean the surface from debris and inspect the
surface for burrs or pitting.
If not taken care of, there is a risk of short circuit.
Warning - Service required The sensor has a critical issue. Contact your local
Marport oice or dealer.
Caution - Maintenance
required
The sensor has an issue impacting its proper
functioning. Reasons can be:
• The battery is worn out and the charging capacity is
diminished.
• Shoulder bolts are in a bad condition, the charge is
not optimal.
Caution - Replace battery The battery capacity is very low and will soon be
exhausted.
United Kingdom
Marport UK ltd
32 Wilson Street
Peterhead, AB42 1UD
United Kingdom
[email protected]