Marshalltown VP3800 User manual

VIBRATORY PLATE COMPACTOR
Part# VP3800 | EDI# 28693
Part# VP3800W | EDI# 29542
104 S. 8th Ave. | Marshalltown, IA
Phone [phone] | Fax [phone]
www.MARSHALLTOWN.com
WS2732

2 of 26 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732
INTRODUCTION
Congratulations on your purchase of a MARSHALLTOWN vibratory plate compactor. MARSHALLTOWN prides
itself in producing the highest quality construction tools and equipment for the professional and has applied the
same research, design, and production principles to these plate compactors.
These powerful machines are designed for compacting granular fill materials and asphalt. The VP3800 is a leader
in it’s class in both centrifugal force and operation speed. With 3,800 pounds of centrifugal force you can expect a
well-compacted base while traveling at over 100 feet per minute.
The VP3800W can be used in all applications but it’s water tank feature is necessary for keeping material from
sticking to the bottom of the plate during asphalt paving and patching. It’s water tank can be filled on the machine
or easily removed and replaced to fill at a water source.
Your MARSHALLTOWN plate compactor has a first of it’s kind foldable handle that locks into place during
transport and while moving around the job site. A lifting loop built into the frame allows for lifting strap or forklift
access for job site placement
This machine was built with user safety in mind, however, it can present hazards if improperly operated and
serviced. Carefully read and follow all safety and operating instructions in this manual. Ensure every operator
reads this manual before operating the unit. The replacement of any part with anything other than the
manufacturer’s authorized replacement part may adversely affect the performance, durability, and safety of
the product. Be sure safety precautions are observed. Read and follow all safety and operating instructions in
this operator’s manual. The manufacturer reserves the right to make changes on or add improvements to its
product at any time without prior notice or obligation. The manufacturer reserves the right to decide, upon its
sole discretion and at any time, to discontinue this product. Information regarding operation and maintenance of
the engine can be found in a separate engine manual supplied with this machine. The engine manual provides all
the information required regarding engine adjustments, operation and maintenance. Should any questions arise
concerning engine operation or service, contact the nearest engine repair facility or the engine manufacturer. This
manual covers all MARSHALLTOWN plate compactors and options. For technical questions or repair parts, please
call MARSHALLTOWN customer service at 1-800-888-0127, 641-753-6341 or visit www.MARSHALLTOWN.com.
TABLE OF CONTENTS
Introduction..................................................................................................................................................................................2
Safety Precautions......................................................................................................................................................................3
Safety Decals ...............................................................................................................................................................................4
Warranty........................................................................................................................................................................................4
Specifications ..............................................................................................................................................................................5
Technical Data - Engine ..............................................................................................................................................................6
Suggested Retail Parts...............................................................................................................................................................6
Common Components...............................................................................................................................................................7
Pre-Operation Checks................................................................................................................................................................8
Controls and Accessories..........................................................................................................................................................9
Operation ....................................................................................................................................................................................10
Maintenance......................................................................................................................................................................... 10-11
Parts Breakdown .................................................................................................................................................................12-23
Water Tank Option.............................................................................................................................................................. 20-24
Troubleshooting.........................................................................................................................................................................25

3 of 26
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732
SAFETY PRECAUTIONS
WARNING safety signs are located near specific hazards.
General precautions are listed on CAUTION safety signs.
This notation appears before warnings in the text. It means that the step that follows must be carried out to avoid
the possibility of personal injury or death. These warnings are intended to help the technician avoid any potential
hazards encountered in the normal service procedures. We strongly recommend that the reader takes advantage of the
information provided to prevent personal injury or injury to others.
THE FOLLOWING PRECAUTIONS ARE SUGGESTED TO HELP PREVENT ACCIDENTS. A CAREFUL OPERATOR IS THE
BEST OPERATOR. MOST ACCIDENTS CAN BE AVOIDED BY OBSERVING CERTAIN PRECAUTIONS. READ AND TAKE THE
FOLLOWING PRECAUTIONS BEFORE OPERATING THIS EQUIPMENT TO HELP PREVENT ACCIDENTS. EQUIPMENT
SHOULD BE OPERATED ONLY BY THOSE WHO ARE RESPONSIBLE AND INSTRUCTED TO DO SO.
CALIFORNIA PROPOSITION 65 WARNING: Operation of this equipment and/or engine exhaust from this product
contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
• Read all operating and maintenance instructions before operating or servicing the machine.
• Equipment is only as safe as its operator. Give complete and undivided attention to the operation of the equipment.
• Keep inexperienced and unauthorized people away from equipment at all times.
• Know how to stop the equipment instantly.
• Test all safety switches before every use.
• Always have all guards and safety devices attached and in place before operating equipment.
NEVER operate the plate compactor with the belt guard cover off.
NEVER let go of the plate compactor or walk away from it while it is running.
• Always make sure engine RPM’s are low and clutch is not engaged when idling engine during warm up.
• Always make sure engine is stopped with the switch in the “OFF” position before making any adjustments or putting
hands or tools near the plate compactor.
• Always make sure engine is in “OFF” position when servicing or not in use.
• Keep the plate compactor in good condition. Loose or damaged parts are dangerous.
• Avoid loose clothing that could get caught in moving parts.
Keep hands and feet away from moving parts.
• Always allow ample time for the plate compactor to cool before making any adjustments.
• Do not smoke while refueling the engine. Ensure the engine is in the “off” position and allow it to cool before refueling.
• Do not spill fuel.
• NEVER operate the plate compactor in confined areas without ample ventilation.
• Keep all warning, caution and safety instruction labels in good condition. Replace missing, damaged or illegible labels.
• DO NOT OPERATE this plate compactor under the influence of alcohol or while taking medication that impairs
your reactions.
• Never sit or ride on the plate compactor.
• Always properly secure machine before transporting.
• Always follow recommended maintenance schedules.
• Use factory authorized parts for replacement.
• Never try to lift unit by yourself.
• Wear safety glasses and hearing protection while operating the plate compactor.
• Wear proper protective clothing while operating plate compactor, including eye, ear, and clothing.
• Clear the work area around the machine to prevent tripping or falling onto the plate compactor.
• Do not operate the plate compactor on extreme inclines.
WARNING!
CAUTION!
CAUTION!
CAUTION!
WARNING!
CAUTION!
CAUTION!

4 of 26 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732
SAFETY DECALS
If your safety decals are damaged, they can be replaced by contacting Customer Service.
Do not operate without all guards in place
Never operate machine if parts are damaged
Do not operate prior to reading
Plate Compactor Manual
Stay away from engine, belts, and
other moving parts
WS2844
To avoid pinch points, make sure engine
is stopped and in the “off” position before
making adjustments
Avoid contacting the engine, vibration plate,
and frame after use as surfaces may be hot
Never let go of or walk away from
machine while it’s running
WARNING
VP3800
VP3800W
WS2844
3 YEAR PLATE COMPACTOR WARRANTY
This product is warranted to the original purchaser only to be free of defects in material and workmanship,
under normal use and servicing, for a period of 3 years from the purchase date, excluding the engine. Warranty
on the engine is limited to the warranty extended by the engine manufacturer and any warranty claims related to
the engine should be directed to the engine manufacturer. MARSHALLTOWN Company’s sole obligation under
this warranty is limited to the replacement or repair of the product or covered part(s) at no charge delivered
to you F.O.B standard ground rates from its designated facility if the product is determined upon inspection by
MARSHALLTOWN Company to have been defective in materials or workmanship. MARSHALLTOWN Company’s
warranty for replacement parts will extend for the duration of the original product warranty.
This warranty will not apply when the product becomes damaged or inoperative due to misuse, abuse, normal
wear and tear, neglect, improper maintenance, accident, or freight damage; if the product has not been
operated and maintained in accordance with the instructions furnished in the Operator’s Manual; or when the
product has been altered or modified without approval from MARSHALLTOWN Company.
Under no circumstances shall MARSHALLTOWN Company be responsible or liable for any consequential,
special, or punitive damages, pickup and delivery of the unit, inbound shipping charges to MARSHALLTOWN
Company’s service facility, rental charges for a replacement unit, loss of income, or other loss resulting from the
failure of the product to function properly because of a defect in material or workmanship covered under this
warranty.
There are no warranties which extend beyond the description of this warranty. No employee or agent of
MARSHALLTOWN Company has the authority to modify this warranty.
If you wish to make a warranty claim, contact Customer Service at 1-800-888-0127 for return authorization and
instructions.
THE FOREGOING LIMITED WARRANTIES ARE EXCLUSIVE AND ARE GIVEN AND ACCEPTED IN LIEU OF
ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER
REMEDIES. MARSHALLTOWN COMPANY’S TOTAL LIABILITY ARISING OUT OF SUPPLYING AND THE USE OF
THE EQUIPMENT, WHETHER BASED ON A CLAIM OF WARRANTY, NEGLIGENCE, OR OTHERWISE, SHALL NOT
EXCEED THE COST PAID BY YOU FOR THE EQUIPMENT.
R6232WS2853
WS2843
WS2842
WS2845

5 of 26
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732
SPECIFICATIONS
CENTRIFUGAL FORCE  LB  KG
VIBRATION FREQUENCY  VPM  HZ
TRAVELING SPEED  FTMIN  MMIN
PLATE SIZE L X W ."X ."  X MM
MAX. AREA OF COMPACTION , SQ FTHR  SQ MHR
OPERATING WEIGHT  LB  KG
WATER TANK CAPACITY  GAL . L
LUBRICATING OIL IN EXCITER CASE . OZ CC OF FULL SYNTHETIC W-
22/"
(561mm)
24/" (632mm)
28/" (735mm)
48/" (1221mm)
35/"
(894mm)
18/" (480mm)

6 of 26 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732
SUGGESTED RETAIL PARTS
EDI NAME
32359 V-BELT, AX31 TRI-POWER
 THROTTLE LEVER/CABLE KIT
 OPERATING HANDLE KIT
 RETRACTABLE HANDLE LOCK KIT
 HANDLE BUSHING/CONNECTION KIT
 VIBRATION ISOLATOR KIT
 LIFT HANDLE KIT (PAIR)
 DRIVEN PULLEY KIT
 CLUTCH KIT
 BELT GUARD KIT
32352 THROTTLE CLIPS
32362 WATER TANK KIT
32363 WATER TANK
32364 WATER LINE
32365 END CAP (CLOSED)
32366 END CAP (OPEN)
TECHNICAL DATA - ENGINE
HONDA GX160
WEIGHT LBS 33
DISPLACEMENT CM^ 163
OIL CAPACITY US QT 0.61
FUEL TANK CAPACITY US GAL. 0.82
FUEL  OCTANE OR HIGHER
IDLE SPEED RPM 1400
TOP SPEED RPM 3800
SPARK PLUG BPR6ES (NGK)
SPARK PLUG GAP .7 to .8 mm
ENGINE OIL SAE 10W30
EXCITER OIL . OZ FULL SYNTHETIC W-

7 of 26
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732
COMMON COMPONENTS
REF # NAME REF # NAME
1 HANDLE 9 WATER TANK (if applicable)
2 THROTTLE LEVER 10 WATER TANK STRAP (if applicable)
3 THROTTLE CABLE 11 WATER VALVE (if applicable)
4 HANDLE LOCKS 12 DRIP BAR (if applicable)
5 GAS TANK 13 BASE PLATE
6 FUEL VALVE LEVER AND CHOKE 14 LIFTING LOOP
7 ON/OFF SWITCH 15 BEARING HOUSING
8 AIR FILTER 16 ENGINE MOUNTING NUTS
1
2
3
4
4
8
5
5
9
10
11
12
12
13
15
7
6
15
15
14
14
9
10
16
16

8 of 26 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732
PRE-OPERATION CHECKS
After removing plate compactor from pallet and packaging, there is no assembly.
The operator must be familiar with the location and operation of all controls. In a safe and well-ventilated area
preform the following:
1. Check entire machine for loose or missing hardware. Contact MARSHALLTOWN Customer Service
at 800-888-0127 if any pieces are missing.
2. Check the fuel filter and inspect air filter.
3. The plate compactor comes filled with exciter oil, so there is no need to check oil level. See Scheduled
Maintenance for oil replacement schedule (page 11).
5. The plate compactor ships with engine oil, but
check prior to starting.
4. The throttle cable/lever comes connected to the handle (A) and carburetor (B). Move throttle lever and watch
movement on the carburetor to insure correct operation.
6. Correct belt tension can be checked by using
moderate pressure to squeeze both sides of belt.
Approximately 1" of movement is correct tension.
Loosen engine mounting plate and adjust to
correct belt tension. Retighten.
A
B

9 of 26
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732
CONTROLS AND ACCESSORIES
Handle lock (C) – The handle can lock into place during storage and transport. Always unlock handle into
operating position when in use.
Throttle lever – When starting compactor, position the throttle lever towards front of unit (D). Idle in this
position during warm up.
Adjust throttle lever away from front (E) of unit to engage clutch and operate plate compactor.
C
Throttle in idle position
during warm-up
Pull back to increase throttle
during use
D E

10 of 26 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732
OPERATION
STARTING THE ENGINE
1. On a cold engine, move choke lever to CLOSED
position. To restart a warm engine leave choke in
OPEN .
2. Switch the On/Off Switch to the On position.
3. Switch the fuel valve lever on.
4. Pull the starter grip lightly until you feel
resistance, then pull briskly. Repeat until engine
starts.
5. If the choke lever was moved to the CLOSED
position to start the engine, gradually move it to
the OPEN position as the engine warms up.
RESTARTING THE ENGINE
1. Leave the choke lever in the OPEN position.
2. Switch the On/Off Switch to the On position.
3. Switch the fuel valve lever on.
4. Pull the starter grip lightly until you feel
resistance, then pull briskly. Repeat until engine
starts.
MAINTENANCE
CHECK OIL LEVEL BEFORE EACH USE
CHANGE ENGINE OIL FIRST MONTH OR  HRS. -  MO. OR  HRS AFTER
CHANGE EXCITER OIL EVERY  HOURS OR EVERY  YEARS
CHECK FUEL LEVEL BEFORE EACH USE
CHECK AIR FILTER BEFORE EACH USE
CHECK BELT EVERY  HOURS OR EVERY  MONTHS
CHANGE BELT AS NEEDED
CHECK THROTTLE BEFORE EACH USE
REPLACE AIR FILTER EVERY  HOURS OR EVERY  MONTHS
SPARK PLUG - CHECK AND ADJUST EVERY  HOURS OR  YEAR
SPARK PLUG - REPLACE EVERY  HOURS OR  YEARS
CHECK NUTS AND BOLTS BEFORE EACH USE
Choke Lever
On/Off Switch
Fuel Valve Lever

11 of 26
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732
MAINTENANCE
CHANGING THE BELT
1. Remove 4 hex head screws (F) holding blade guard in place.
2. Loosen 4 engine mounting plate nuts (G).
3. Slide engine and mounting plate forward so belt can be removed.
4. Install new belt.
5. EVENLY pull mounting plate back to tighten belt on pulleys.
Approximately 1" amount of slack in the belt is acceptable.
6. Tighten mounting plate nuts.
7. Replace belt guard.
CHANGING EXCITER OIL
1. When changing the exciter oil, remove the drain plug located
at the bottom-right of the exciter housing (H), and simply tip the
compactor to drain the oil. Note that the oil will drain more easily
while it is hot. Remember to use only 10W30 motor oil when
replacing exciter oil.
PLATE COMPACTOR STORAGE
For storage of the plate compactor for over 30 days,
the following is required:
1. Drain the fuel tank completely or add STA-BIL to the fuel.
2. Run the engine until the fuel is completely consumed.
3. Completely drain the oil from the engine crankcase and follow
procedures described in the HONDA engine Owner’s Manual
for engine storage.
4. Completely drain the compactor’s hydraulic oil from the
vibrating case.
5. Clean entire plate compactor, especially the bottom plate,
removing all dirt and foreign matter.
6. Cover plate compactor and engine with plastic covering or
equivalent and store in a clean, dry place.
F
F
F
F
G
H
G

12 of 26 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732
PARTS BREAKDOWN - VP3800
QTY.PART #
NAME
REF. #
1R3929
BASE PLATE ASSEMBLY
1
1R3932
MOTOR ADJUSTMENT ASSEMBLY
2
1R3933
FRAME ASEMBLY
3
1R3934
HANDLE ASSEMBLY
4
1WR1470
PH SCREW 10-24 X 1.5" LONG
5
1WX2623
THROTTLE LEVER-FRICTION STYLE WITH CABLE
6
3WR370
NYLOK LOCKNUT, 10-24
7
1WR1468
SINGLE CONDUIT SNAP CLIP
8
1WR1469
LOOSE STRING-ON CLIP
9
2WR1502
HHCS, 5/16-18 UNC, 2.75 in. LONG
10
2WL711HANDLE BUMPER11
2WR1459
HHCS, 1/2-13 UNC, 3 in. LONG
12
2WR1078
NYLOK LOCKNUT, 1/2-13
13
2WX2443
HANDLE, MOUNT PLATE
14
9WR118
NYLOK LOCKNUT, 5/16-18
15
4WR1458
HHCS 5/16"-18 X 1/2" LONG
16
4WR364
LOCKWASHER, 5/16 INCH, REGULAR
17
8WR236
WASHER FLAT, 5/16
18
1WL712
BELT GUARD
19
1WK227
A-SECTION, V-BELT, AX-31 TRI-POWER
20
2WR1396
HHCS 5/16" - 18 UNC, 2 in. LONG
21
1WR1007
HHCS, 5/16-18 UNC, 1 in. LONG
22
2
PH SCREW 10-24 X 1.25" LONG
23
THIS PRINT DISCLOSES SUBJECT MATTER IN WHICH MARSHALLTOWN COMPANY HAS PROPRIETARY RIGHTS. THE RECEIPT OR
POSSESSION OF THIS PRINT DOES NOT CONFER, TRANSFER OR LICENSE THE USE OF THE DESIGN OR TECHNICAL INFORMATION SHOWN
HEREIN. REPRODUCTION OF THIS PRINT OR ANY INFORMATION CONTAINED HEREIN OR MANUFACTURE OF ANY ARTICLE HEREFROM,
FOR DISCLOSURE TO OTHERS, IS FORBIDDEN, EXCEPT BY SPECIAL WRITTEN PERMISSION FROM MARSHALLTOWN COMPANY.
HEAT-TREAT
MATERIAL
APVD.
BY
DATE
CK.
BY
DWN.
BY
DATE DATE
REV.
DRAWING NO.
OF
NO.
PART
MACH. NO.
FIXT. NO.NO.
E.D.I. SCALE
DIE NO.
GA. NO.
SHEET
TITLE:
REV. REVISION DESCRIPTION DATE APVD
#
C
UNLESS OTHERWISE SPECIFIED:
ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]
GENERAL UNSPECIFIED TOLERANCES
SUPPLIER VERIFICATION IS
REQUIRED PRIOR TO APPROVAL
CRITICAL DIMENSION / NOTE
FRACTION:
 .5
ANGLE:
 1/32
°
 XXXX
 XX
 XXX
 .020
DECIMAL: in. [mm]
 .010
 .005
 .0005
 - [.5]
 X
-
[.013]
[.12]
[.25]
X
1:5 28693 -
1 1
PLATE COMPACTOR FULL ASSEMBLY
BML
3/1/2021
C:\VaultLocal\Public\ARWorkingDirectory\BML\PlateCompactor\28693.idw
V15
1
15
18
2
3
4
6
7
8
7
9
23
11
15
13
14
11
12
16
17
18
18
17
16
20
19
15
18
15
21
22
16
12
10
10
15
5
23

13 of 26
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732
PARTS BREAKDOWN - VP3800
REF # NAME PART # QTY
1 BASE PLATE ASSEMBLY R3929 1
2 MOTOR ADJUSTMENT ASSEMBLY R3932 1
3 FRAME ASSEMBLY R3933 1
4 HANDLE ASSEMBLY R3934 1
5 PH SCREW 10-24 X 1.5" LONG WR1470 1
6 THROTTLE LEVER-FRICTION STYLE WITH CABLE WX2623 1
7 NYLOK LOCKNUT, 10-24 WR370 3
8 SINGLE CONDUIT SNAP CLIP WR1468 1
9 LOOSE STRING-ON CLIP WR1469 1
10 HHCS, 5/16-18 UNC, 2.75 in. LONG WR1502 2
11 HANDLE BUMPER WL711 2
12 HHCS, 1/2-13 UNC, 3 in. LONG WR1459 2
13 NYLOK LOCKNUT, 1/2-13 WR1078 2
14 HANDLE, MOUNT PLATE WX2443 2
15 NYLOK LOCKNUT, 5/16-18 WR118 9
16 HHCS 5/16"-18 X 1/2" LONG WR1458 4
17 LOCKWASHER, 5/16 INCH, REGULAR WR364 4
18 WASHER FLAT, 5/16 WR236 8
19 BELT GUARD WL712 1
20 A-SECTION, V-BELT, AX-31 TRI-POWER WK227 1
21 HHCS 5/16" - 18 UNC, 2 in. LONG WR1396 2
22 HHCS, 5/16-18 UNC, 1 in. LONG WR1007 1
23 PH SCREW 10-24 X 1.25" LONG N/A 2
THROTTLE LEVER/CABLE KIT EDI# 32351 INCLUDES:
REF # NAME PART # QTY
5 PH SCREW - 10-24 X 1.5" LONG WR1470 1
6 THROTTLE LEVER-FRICTION STYLE WITH CABLE VP3800 WX2623 1
7 #10-24 NYLOK NUT, TOP LOCK STYLE WR370 2
23 PH SCREW - 10-24 X 1.25" LONG N/A 1
NOT
SHOWN NYLON WASHER N/A 1

14 of 26 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732
THROTTLE CLIPS KIT EDI# 32352 INCLUDES:
OPERATING HANDLE KIT EDI# 32353 INCLUDES:
BELT GUARD KIT EDI# 32357 INCLUDES:
V-BELT, AX31 TRI-POWER KIT EDI# 32359 INCLUDES:
REF # NAME PART # QTY
7 #10-24 NYLOK NUT, TOP TOCK STYLE WR370 1
8 SINGLE CONDUIT SNAP CLIP - WESCON 22-0203-00 WR1468 1
9 LOOSE STRING-ON CLIP - WECON 22-2152-03 WR1469 1
23 PH SCREW - 10-24 X 1.25" LONG N/A 1
REF # NAME PART # QTY
4 HANDLE-VP3800-PC-BLUE R4522 1
10 5/16IN-18 X 2-3/4IN GRADE 5 ZINC HEX CAP SCREW WR1502 2
11 HANDLE BUMPER WL711 3
12 HHCS 1/2"-13 UNC X 3", ZINC PLATED WR1459 2
13 LOCKNUT 1/2-13 PLATED WR1078 2
14 HANDLE, MOUNT PLATE-VP3800-PC-BLUE R4523 2
15 00517 NYLON LOCKNUT, 5/16-18 WR118 2
REF # NAME PART # QTY
16 HHCS 5/16"-18 X 1/2" LONG, ZINC PLATED WR1458 4
17 LOCKWASHER 5/16 SPLIT, ZINC PLATED WR364 4
18 FLAT WASHER, " ZINC PLATED USS WR236 4
19 BELT GUARD WL712 1
REF # NAME PART # QTY
20 A-SECTION, V-BELT, AX31 TRI-POWER WK227 1

15 of 26
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732
PARTS BREAKDOWN - HANDLE
QTY.PART #
NAME
REF. #
1R4522HANDLE1
2WX2423
RETRACTABLE SPRING PLUNGER WITH L-HANDLE
2
4WR1402
HEX NUT, JAM, 5/8"-11 UNC
3
4WR1420
LOCKWASHER, INCH, REGULAR 5/8"
4
THIS PRINT DISCLOSES SUBJECT MATTER IN WHICH MARSHALLTOWN COMPANY HAS PROPRIETARY RIGHTS. THE RECEIPT OR
POSSESSION OF THIS PRINT DOES NOT CONFER, TRANSFER OR LICENSE THE USE OF THE DESIGN OR TECHNICAL INFORMATION SHOWN
HEREIN. REPRODUCTION OF THIS PRINT OR ANY INFORMATION CONTAINED HEREIN OR MANUFACTURE OF ANY ARTICLE HEREFROM,
FOR DISCLOSURE TO OTHERS, IS FORBIDDEN, EXCEPT BY SPECIAL WRITTEN PERMISSION FROM MARSHALLTOWN COMPANY.
HEAT-TREAT
MATERIAL
APVD.
BY
DATE
CK.
BY
DWN.
BY
DATE DATE
REV.
DRAWING NO.
OF
NO.
PART
MACH. NO.
FIXT. NO.NO.
E.D.I. SCALE
DIE NO.
GA. NO.
SHEET
TITLE:
REV. REVISION DESCRIPTION DATE APVD
#
C
UNLESS OTHERWISE SPECIFIED:
ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]
GENERAL UNSPECIFIED TOLERANCES
SUPPLIER VERIFICATION IS
REQUIRED PRIOR TO APPROVAL
CRITICAL DIMENSION / NOTE
FRACTION:
.5
ANGLE: 1/32
°
XXXX
XX
XXX
.020
DECIMAL: in. [mm]
.010
.005
.0005
- [.5]
X
-
[.013]
[.12]
[.25]
X
1:2
R3934 -
1 1
HANDLE ASSEMBLY
brian.lea
2/17/2021
C:\VaultLocal\Public\ARWorkingDirectory\BML\PlateCompactor\R3934.idw
V7
2
2
3
3
3
3
1
4
4
REF # NAME PART # QTY
1 HANDLE R4522 1
2 RETRACTABLE SPRING PLUNGER WITH L-HANDLE WX2423 2
3 HEX NUT, JAM, " -  UNC WR1402 4
4 LOCKWASHER, INCH, REGULAR 5/8" WR1420 4
RETRACTABLE HANDLE LOCK KIT EDI# 32354 INCLUDES:
REF # NAME PART # QTY
2 RETRACTABLE SPRING PLUNGER WITH L-HANDLE 20" ZINC PLATED WX2423 1
3 HEX NUT, JAM, 5/8"-11 UNC WR1402 2
4 LOCKWASHER, INCH, REGULAR " WR1420 2

16 of 26 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732
PARTS BREAKDOWN - FRAME
QTY.PART #
NAME
REF. #
1R4519FRAME1
1R4520
BELT GUARD MOUNT PLATE
2
2WR1404
ZINC-PLATED STEEL SQUARE NECK CARRIAGE BOLT
3
2WR118
NYLOK LOCKNUT, 5/16-18
4
2R4521
LIGHT DUTY DRY-RUNNING SLEEVE BEARING
5
2WX2563
OIL-EMBEDDED SLEEVE BEARING
6
THIS PRINT DISCLOSES SUBJECT MATTER IN WHICH MARSHALLTOWN COMPANY HAS PROPRIETARY RIGHTS. THE RECEIPT OR
POSSESSION OF THIS PRINT DOES NOT CONFER, TRANSFER OR LICENSE THE USE OF THE DESIGN OR TECHNICAL INFORMATION SHOWN
HEREIN. REPRODUCTION OF THIS PRINT OR ANY INFORMATION CONTAINED HEREIN OR MANUFACTURE OF ANY ARTICLE HEREFROM,
FOR DISCLOSURE TO OTHERS, IS FORBIDDEN, EXCEPT BY SPECIAL WRITTEN PERMISSION FROM MARSHALLTOWN COMPANY.
HEAT-TREAT
MATERIAL
APVD.
BY
DATE
CK.
BY
DWN.
BY
DATE DATE
REV.
DRAWING NO.
OF
NO.
PART
MACH. NO.
FIXT. NO.NO.
E.D.I. SCALE
DIE NO.
GA. NO.
SHEET
TITLE:
REV. REVISION DESCRIPTION DATE APVD
#
C
UNLESS OTHERWISE SPECIFIED:
ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]
GENERAL UNSPECIFIED TOLERANCES
SUPPLIER VERIFICATION IS
REQUIRED PRIOR TO APPROVAL
CRITICAL DIMENSION / NOTE
FRACTION:
 .5
ANGLE:
 1/32
°
 XXXX
 XX
 XXX
 .020
DECIMAL: in. [mm]
 .010
 .005
 .0005
 - [.5]
 X
-
[.013]
[.12]
[.25]
X
1:2
R3933 -
1 1
FRAME ASSEMBLY
brian.lea
2/17/2021
C:\VaultLocal\Public\ARWorkingDirectory\BML\PlateCompactor\R3933.idw
V6
1
6
5
5
6
3
2
4
REF # NAME PART # QTY
1 FRAME R4519 1
2 BELT GUARD MOUNT PLATE R4520 1
3 ZINC-PLATED STEEL SQUARE NECK CARRIAGE BOLT WR1404 2
4 NYLOK LOCKNUT, 5/16-18 WR118 2
5 LIGHT DUTY DRY-RUNNING SLEEVE BEARING R4521 2
6 OIL-EMBEDDED SLEEVE BEARING WX2563 2
HANDLE BUSHING/CONNECTION KIT EDI# 32355 INCLUDES:
REF # NAME PART # QTY
3 LIGHT DUTY DRY-RUNNING SLEEVE BEARING WP-3800 R4521 2
6 OIL-EMBEDDED SLEEVE BEARING, 1.75" LONG WX2563 2
NOT SHOWN HHCS "- UNC X ", ZINC PLATED WR1459 2
NOT SHOWN LOCKNUT 1/2-13 PLATED WR1078 2
NOT SHOWN 5/16IN-18 X 2-3/4IN GRADE 5 ZINC HEX CAP SCREW WR1502 2
NOT SHOWN 00517 NYLON LOCKNUT, 5/16-18 WR118 2

17 of 26
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732
PARTS BREAKDOWN - MOTOR ADJUSTMENT
QTY.PART #
NAME
REF. #
1WX2301
ENGINE, HONDA GX160
1
1R4518
MOTOR MOUNT ADJUSTMENT PLATE
2
1WX2465
HONDA GX160 EXHAUST DEFLECTOR
3
2WR1457
PAN HEAD SCREW M4 X 5MM
4
1R4535
Steel Spacer 0.425”Long-VP3800
5
1WX2528
CLUTCH ASSEMBLY
6
1WR1419
HHCS, 5/16-24 UNF, 1.25 in. LONG
7
1WR1418
WASHER, ANSI B WIDE 5/16"
8
4WR118
NYLOK LOCKNUT, 5/16-18
9
4WR1008
HHCS, 5/16-18 UNC, 1.5 in. LONG
10
THIS PRINT DISCLOSES SUBJECT MATTER IN WHICH MARSHALLTOWN COMPANY HAS PROPRIETARY RIGHTS. THE RECEIPT OR
POSSESSION OF THIS PRINT DOES NOT CONFER, TRANSFER OR LICENSE THE USE OF THE DESIGN OR TECHNICAL INFORMATION SHOWN
HEREIN. REPRODUCTION OF THIS PRINT OR ANY INFORMATION CONTAINED HEREIN OR MANUFACTURE OF ANY ARTICLE HEREFROM,
FOR DISCLOSURE TO OTHERS, IS FORBIDDEN, EXCEPT BY SPECIAL WRITTEN PERMISSION FROM MARSHALLTOWN COMPANY.
HEAT-TREAT
MATERIAL
APVD.
BY
DATE
CK.
BY
DWN.
BY
DATE DATE
REV.
DRAWING NO.
OF
NO.
PART
MACH. NO.
FIXT. NO.NO.
E.D.I. SCALE
DIE NO.
GA. NO.
SHEET
TITLE:
REV. REVISION DESCRIPTION DATE APVD
#
C
UNLESS OTHERWISE SPECIFIED:
ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]
GENERAL UNSPECIFIED TOLERANCES
SUPPLIER VERIFICATION IS
REQUIRED PRIOR TO APPROVAL
CRITICAL DIMENSION / NOTE
FRACTION:
 .5
ANGLE:
 1/32
°
 XXXX
 XX
 XXX
 .020
DECIMAL: in. [mm]
 .010
 .005
 .0005
 - [.5]
 X
-
[.013]
[.12]
[.25]
X
1:2 R3932 -
1 1
MOTOR ADJUSTMENT ASSEMBLY
brian.lea
2/17/2021
C:\VaultLocal\Public\ARWorkingDirectory\BML\PlateCompactor\R3932.idw
V8
2
1
6
5
3
4
8
7
9
9
10
REF # NAME PART # QTY
1 ENGINE, HONDA GX160 WX2301 1
2 MOTOR MOUNT ADJUSTMENT PLATE R4518 1
3 HONDA GX EXHAUST DEFLECTOR WR1457 1
4 PAN HEAD SCREW M4 X 5MM WR1457 2
5 STEEL SPACER 0.425" LONG-CP3800 R4535 1
6 CLUTCH ASSEMBLY WX2528 1
7 HHCS, 5/16-24 UNF, 1.25" LONG WR1419 1
8 WASHER, ANSI B WIDE 5/16" WR1418 1
9 NYLOK LOCKNUT, 5/16-18 WR118 4
10 HHCS, 5/16-18 UNC, 1.5" LONG WR1008 4
CLUTCH KIT EDI# 32361 INCLUDES:
REF # NAME PART # QTY
5 STEEL SPACER 0.425" LONG-VP3800 R4535 1
6 CLUTCH ASSEMBLY, 4.0" OD WX2528 1
7 HHCS 5/16"-24, UNF X 1.25" WR1419 1
8 WASHER, FENDER, EXTRA HEAVY, 5/16 X 1 X 1/8 WR1418 1
QTY.PART #
NAME
REF. #
1WX2301
ENGINE, HONDA GX160
1
1R4518
MOTOR MOUNT ADJUSTMENT PLATE
2
1WX2465
HONDA GX160 EXHAUST DEFLECTOR
3
2WR1457
PAN HEAD SCREW M4 X 5MM
4
1R4535
Steel Spacer 0.425”Long-VP3800
5
1WX2528
CLUTCH ASSEMBLY
6
1WR1419
HHCS, 5/16-24 UNF, 1.25 in. LONG
7
1WR1418
WASHER, ANSI B WIDE 5/16"
8
4WR118
NYLOK LOCKNUT, 5/16-18
9
4WR1008
HHCS, 5/16-18 UNC, 1.5 in. LONG
10
THIS PRINT DISCLOSES SUBJECT MATTER IN WHICH MARSHALLTOWN COMPANY HAS PROPRIETARY RIGHTS. THE RECEIPT OR
POSSESSION OF THIS PRINT DOES NOT CONFER, TRANSFER OR LICENSE THE USE OF THE DESIGN OR TECHNICAL INFORMATION SHOWN
HEREIN. REPRODUCTION OF THIS PRINT OR ANY INFORMATION CONTAINED HEREIN OR MANUFACTURE OF ANY ARTICLE HEREFROM,
FOR DISCLOSURE TO OTHERS, IS FORBIDDEN, EXCEPT BY SPECIAL WRITTEN PERMISSION FROM MARSHALLTOWN COMPANY.
HEAT-TREAT
MATERIAL
APVD.
BY
DATE
CK.
BY
DWN.
BY
DATE DATE
REV.
DRAWING NO.
OF
NO.
PART
MACH. NO.
FIXT. NO.NO.
E.D.I. SCALE
DIE NO.
GA. NO.
SHEET
TITLE:
REV. REVISION DESCRIPTION DATE APVD
#
C
UNLESS OTHERWISE SPECIFIED:
ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]
GENERAL UNSPECIFIED TOLERANCES
SUPPLIER VERIFICATION IS
REQUIRED PRIOR TO APPROVAL
CRITICAL DIMENSION / NOTE
FRACTION:
 .5
ANGLE:
 1/32
°
 XXXX
 XX
 XXX
 .020
DECIMAL: in. [mm]
 .010
 .005
 .0005
 - [.5]
 X
-
[.013]
[.12]
[.25]
X
1:2 R3932 -
1 1
MOTOR ADJUSTMENT ASSEMBLY
brian.lea
2/17/2021
C:\VaultLocal\Public\ARWorkingDirectory\BML\PlateCompactor\R3932.idw
V8
2
1
6
5
3
4
8
7
9
9
10

18 of 26 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732
PARTS BREAKDOWN - BASE PLATE
QTY.PART #
NAME
REF #
1PD6225
BASE PLATE, MACHINED
1
1WX2461-IR
CYLINDRICAL ROLLER BEARING (INNER RACE)
2
1WX2461
CYLINDRICAL ROLLER BEARING (OUTER RACE)
3
2WK224
BUNA N O-RING, DASH 240
4
1R4424-010
END CAP, MACHINED (CLOSED)
5
1R4423-010
END CAP, MACHINED (OPEN)
6
1WX2460
SPHERICAL ROLLER BEARING
7
1WR1417
STEEL MACHINE KEY 0.25 X 0.25 X 0.75
8
1PB6232
EXCITER SHAFT, MACHINED
9
10WR1007
SCREW HEX HD 5_16-18X1
10
6WR364
Regular Helical Spring Lock Washers(Inch Series)
11
1WR1398
HHCS 1/2"-13 UNC X 0.875"
12
1WR411
WASHER-1/2" ZINC PLATED
13
1WB125
CAST IRON PULLEY
14
1R4524
Steel Spacer 0.280”Long-VP3800
15
1WX2463
RADIAL SHAFT SEAL
16
8WR256
LOCKWASHER, 1/2" ZINC PLATED SPLIT
18
2R4516
HANDLE, LIFT SIDE
19
4WK222
VIBRATION DAMPING SANDWICH MOUNT
20
4WR1455
HHCS 1/2"-13 unc X 0.75"
21
1R4517
MOTOR ISOLATOR PLATE
22
1
WS229MODEL/SERIAL PLATE
23
4WR1462
1/8" POP RIVET
24
1WR1405
NPT PIPE PLUG
25
4WR1018
HCS 1/2-13 X 1-1/2 Z5
26
THIS PRINT DISCLOSES SUBJECT MATTER IN WHICH MARSHALLTOWN COMPANY HAS PROPRIETARY RIGHTS. THE RECEIPT OR
POSSESSION OF THIS PRINT DOES NOT CONFER, TRANSFER OR LICENSE THE USE OF THE DESIGN OR TECHNICAL INFORMATION SHOWN
HEREIN. REPRODUCTION OF THIS PRINT OR ANY INFORMATION CONTAINED HEREIN OR MANUFACTURE OF ANY ARTICLE HEREFROM,
FOR DISCLOSURE TO OTHERS, IS FORBIDDEN, EXCEPT BY SPECIAL WRITTEN PERMISSION FROM MARSHALLTOWN COMPANY.
HEAT-TREAT
MATERIAL
APVD.
BY
DATE
CK.
BY
DWN.
BY
DATE DATE
REV.
DRAWING NO.
OF
NO.
PART
MACH. NO.
FIXT. NO.NO.
E.D.I. SCALE
DIE NO.
GA. NO.
SHEET
TITLE:
REV. REVISION DESCRIPTION DATE APVD
#
C
UNLESS OTHERWISE SPECIFIED:
ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]
GENERAL UNSPECIFIED TOLERANCES
SUPPLIER VERIFICATION IS
REQUIRED PRIOR TO APPROVAL
CRITICAL DIMENSION / NOTE
FRACTION:
 .5
ANGLE:
 1/32
°
 XXXX
 XX
 XXX
 .020
DECIMAL: in. [mm]
 .010
 .005
 .0005
 - [.5]
 X
-
[.013]
[.12]
[.25]
X
1:3 R3929 -
1 1
BASE PLATE ASSEMBLY
brian.lea
2/17/2021
C:\VaultLocal\Public\ARWorkingDirectory\BML\PlateCompactor\R3929.idw
V15
1
22
2
4
5
10
25
19
20
23
10
10
18
19
20
20
13
12
14
10 11
15
10
11
16 6
4
7
8
9
3
21
18
18
21
11
24
18
26
26
PARTS BREAKDOWN
REF # NAME PART # QTY
1 BASE PLATE, MACHINED PD6225 1
2 CYLINDRICAL ROLLER BEARING (INNER RACE) WX2461-IR 1
3 CYLINDRICAL ROLLER BEARING OUTER RACE WX2461 1
4 BUNA N O-RING, DASH 240 WK224 2
5 END CAP, MACHINED (CLOSED) R4424-010 1
6 END CAP, MACHINED (OPEN) R4423-010 1
7 SPHERICAL ROLLER BEARING WX2460 1
8 STEEL MACHINE KEY 0.25 X 0.25 X 0.75 WR1417 1
9 EXCITER SHAFT, MACHINED PB6232 1
10 SCREW HEX HD 5_16-18 X 1 WR1007 10
11 REGULAR HELICAL SPRING LOCK WASHERS (INCH SERIES) WR364 6
12 HHCS 1/2"-13 UNC X 0.875" WR1398 1
13 WASHER - 1/2" ZINC PLATED WR411 1
14 CAST IRON PULLEY WB125 1
15 STEEL SPACER 0.280" LONG-VP3800 R4524 1
16 RADIAL SHAFT SEAL WX2463 1

19 of 26
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732
REF # NAME PART # QTY
18 LOCKWASHER, 1/2" ZINC PLATED SPLIT WR256 8
19 HANDLE, LEFT SIDE R4516 2
20 VIBRATION DAMPING SANDWICH MOUNT WK222 4
21 HHCS 1/2"-13 UNC X 0.75" WR1455 4
22 MOTOR ISOLATOR PLATE R4517 1
23 MODEL/SERIAL PLATE WS229 1
24 1/8" POP RIVET WR1462 4
25 NPT PIPE PLUG WR1405 1
26 HCS 1/2-13 X 1-1/2 Z5 WR1018 4
VIBRATION ISOLATOR KIT EDI# 32356 INCLUDES:
REF # NAME PART # QTY
18 LOCKWASHER, 1/2" ZINC PLATED SPLIT WK256 8
20 VIBRATION DAMPING SANDWHICH MOUNT WK222 4
21 HHCS 1/2"-13 X 0.75 INCH WR1456 4
26 HHCS 1/2"-13 X 1.5 INCH WR1018 4
DRIVEN PULLEY KIT EDI# 32360 INCLUDES:
END CAP (CLOSED) KIT EDI# 32365 INCLUDES:
END CAP (OPEN) KIT EDI# 32366 INCLUDES:
LIFT HANDLE KIT (PAIR) EDI# 32358 INCLUDES:
REF # NAME PART # QTY
12 HHCS 1/2"-13, UNC X 0.875" WR1398 1
13 WASHER-1/2" ZINC PLATED WR411 1
14 CAST IRON PULLEY WB125 1
15 STEEL SPACER 0.280" LONG-VP3800 R4524 1
REF # NAME PART # QTY
4 BUNA N O-RING, DASH 240 WK224 1
5 END CAP ASSEMBLY-CLOSED-VP3800 R4124 1
10 HCS 5/16-18 X 1 Z5 WR1007 3
11 LOCKWASHER 5/16 SPLIT, ZINC PLATED WR364 3
REF # NAME PART # QTY
4 BUNA N O-RING, DASH 240 WK224 1
6 END CAP ASSEMBLY-OPEN-VP3800 R4123 1
10 HCS 5/16-18 X 1 Z5 WR1007 3
11 LOCKWASHER 5/16 SPLIT, ZINC PLATED WR364 3
REF # NAME PART # QTY
18 LOCKWASHER, 1/2" ZINC PLATED SPLIT WR256 4
19 LOWER GRAB HANDLE-WP3800-PC-BLUE R4516 2
26 HCS 1/2-13 X 1-1/2 Z5 WR1018 4
PARTS BREAKDOWN CONT.

20 of 26 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732
PARTS BREAKDOWN - VP3800W
QTY.PART #
NAME
REF. #
1R3929
BASE PLATE ASSEMBLY
1
1R3932
MOTOR ADJUSTMENT ASSEMBLY
2
1R3933
FRAME ASEMBLY
3
1R3934
HANDLE ASSEMBLY
4
1WR1470
PH SCREW 10-24 X 1.5" LONG
5
1WX2623
THROTTLE LEVER-FRICTION STYLE WITH CABLE
6
3WR370
NYLOK LOCKNUT, 10-24
7
1WR1468
SINGLE CONDUIT SNAP CLIP
8
1WR1469
LOOSE STRING-ON CLIP
9
2WR1502
HHCS, 5/16-18 UNC, 2.75 in. LONG
10
2WL711HANDLE BUMPER11
2WR1459
HHCS, 1/2-13 UNC, 3 in. LONG
12
2WR1078
NYLOK LOCKNUT, 1/2-13
13
2WX2443
HANDLE, MOUNT PLATE
14
9WR118
NYLOK LOCKNUT, 5/16-18
15
4WR1458
HHCS 5/16"-18 X 1/2" LONG
16
4WR364
LOCKWASHER, 5/16 INCH, REGULAR
17
8WR236
WASHER FLAT, 5/16
18
1WL712
BELT GUARD
19
1WK227
A-SECTION, V-BELT, AX-31 TRI-POWER
20
2WR1396
HHCS 5/16" - 18 UNC, 2 in. LONG
21
1WR1007
HHCS 5/16" - 18 UNC, 1 in. LONG
22
2
PH SCREW 10-24 X 1.25" LONG
23
129543
WATER TANK OPTION
24
THIS PRINT DISCLOSES SUBJECT MATTER IN WHICH MARSHALLTOWN COMPANY HAS PROPRIETARY RIGHTS. THE RECEIPT OR
POSSESSION OF THIS PRINT DOES NOT CONFER, TRANSFER OR LICENSE THE USE OF THE DESIGN OR TECHNICAL INFORMATION SHOWN
HEREIN. REPRODUCTION OF THIS PRINT OR ANY INFORMATION CONTAINED HEREIN OR MANUFACTURE OF ANY ARTICLE HEREFROM,
FOR DISCLOSURE TO OTHERS, IS FORBIDDEN, EXCEPT BY SPECIAL WRITTEN PERMISSION FROM MARSHALLTOWN COMPANY.
HEAT-TREAT
MATERIAL
APVD.
BY
DATE
CK.
BY
DWN.
BY
DATE DATE
REV.
DRAWING NO.
OF
NO.
PART
MACH. NO.
FIXT. NO.NO.
E.D.I. SCALE
DIE NO.
GA. NO.
SHEET
TITLE:
REV. REVISION DESCRIPTION DATE APVD
#
C
UNLESS OTHERWISE SPECIFIED:
ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]
GENERAL UNSPECIFIED TOLERANCES
SUPPLIER VERIFICATION IS
REQUIRED PRIOR TO APPROVAL
CRITICAL DIMENSION / NOTE
FRACTION:
 .5
ANGLE:
 1/32
°
 XXXX
 XX
 XXX
 .020
DECIMAL: in. [mm]
 .010
 .005
 .0005
 - [.5]
 X
-
[.013]
[.12]
[.25]
X
1:5
29542 -
1 1
PLATE COMPACTOR WATER OPTION
BML
3/11/2021
C:\VaultLocal\Public\ARWorkingDirectory\BML\PlateCompactor\29542.idw
V7
24
4
6
8
7
23
9
7
11
15
13
14
12
10
14
11
10
12
16
17
18
20
19
17
16
15
15
15
18
15
18
21
22
1
2
18
18
3
5
23