Massoth Piko VT 11.5 TEE User manual

Umbaubericht
Lokomotiven
Piko VT 11.5 TEE en
Backfitting plan of a TEE from PIKO.
Needed parts:
1 x XLS 82205 0
1 x LED lighting board 8124001
1 x LED lighting set from for middle waggons or a selfmade PCB
This plan describes the 1 speaker version.
If you wan’t to install 2 speaker, you HAVE TO USE Ohm speakers instead, and connect
them serial.
Opening the locomotive is quite easy, remove at the traction unit in front the rear plastic cover.
Press lightly on top and pulls the upper part backwards.
Then turn the roof backwards and remove it. (Pict 1).
Pict 1: Removing roof
To remove the front top, pull down the coupler and in the same time push in front of the top (under
TEE) and remove it to the top. (Pict 2)
Stand 18.04.2020 Seite 1 / 11

Umbaubericht
Lokomotiven
Pict 2: Removing front top
Remove first the analog PCB, BUT PLEASE MARK THE CABLE FOR LIGHT FRONT AND
REAR BEFORE.
Have a look in the PIKO manual, you can find a plan for it! (Page 14- Main-PCB)
If you reverse lights nothing will damage, but the Leds are lighting in the wrong way.
Now you are able to open the 14 screws from top, to remove the loco outer wall.(Pict 3-5)
Stand 18.04.2020 Seite 2 / 11

Umbaubericht
Lokomotiven
Stand 18.04.2020 Seite 3 / 11

Umbaubericht
Lokomotiven
Pict 3-5: Open the screws for loco outer wall.
Then you are able to open the 13 screws for the inner part. (Pict 6-9)
Stand 18.04.2020 Seite 4 / 11

Umbaubericht
Lokomotiven
Stand 18.04.2020 Seite 5 / 11

Umbaubericht
Lokomotiven
Pict 6-9: Open the screws for inner part.
As a precaution i removed the lead weight to take some gauze tape on it (like shown in Pict. 2), to
prevent the cables from the sharp edges.
Then screw the lead weight again. (Pict. 10)
Stand 18.04.2020 Seite 6 / 11

Umbaubericht
Lokomotiven
Pict. 10: Preventing cables under lead weight.
Mounting the speaker like pict. 11. You can see here another cable, but you should use the original
cable.
Stand 18.04.2020 Seite 7 / 11

Umbaubericht
Lokomotiven
Pict 11: Mounting the speaker.
Mount the XLS as shown in the inner part of loco and connect it as shown in the manual. Have a
look at these 2 pict. (Pict 12 + 13)
Stand 18.04.2020 Seite 8 / 11

Umbaubericht
Lokomotiven
Pict 12+13: Mount and connect the XLS.
Now connect the cables in following way:
Track + = grey/grey
Track - = white/white
Motor + = red/red
Motor - = blau/blau
Light interior = green (you can also connect it ti A2, if you wan’t to switch it separately)
Light front = yellow/brown (the marked cable for front light)
Light rear = yellow/brown (the marked cable for rear light)
Decoder + (22V) = black/black
Plug in the 2-pole connector for speaker.
Illumination
Cut the LED lighting board as shown in pict. 14 (each 13,5 cm from outside PCB)
As shown in picture you have to drill a hole with a mm drill.
Solder the 2 cables as shown.
Black = +
Green = -
The PCB will fixed with 2 screws 1,5 x 4 .
In traction unit 2 you will mount the other PCB.
Reassemble the traction units in reverse order.
Stand 18.04.2020 Seite 9 / 11

Umbaubericht
Lokomotiven
Pict 14: Assembling and connection of LED lighting board.
Light center coach
Removing the roof is in the same way like the traction unit.
You can buy the PIKO set with 2 PCBs and connect it easily with the cables.
With a breadboard, 8 x LEDs white 5mm and 8 resistors 4, KOhm you can make a slefmade PCB.
Here you can see how the PCB can look like (Pict 15)
Pict 15: Making of the selfmade PCB for LED lighting board.
Stand 18.04.2020 Seite 10 / 11