Master MH-80TBOA-OFR Training manual

CONSUMER: READ AND SAVE THESE IMPORTANT INSTRUCTIONS
GENERAL HAZARD WARNING:
READ AND UNDERSTAND ALL OF THE INSTRUCTIONS IN THIS
MANUAL BEFORE ASSEMBLING, STARTING, OR SERVICING
THE HEATER. Be sure to comply with the instructions and warnings provided with this heater.
Failure to comply can result in fire or explosion that can cause property loss, bodily injury, or
loss of life. Only persons who can follow and understand these instructions should operate
or service this heater. Persons who are impaired or under the influence of alcohol or drugs
should not operate heater. If you need heater info; such as an operating manual, labels,
etcetera, contact Pinnacle Climate Technologies at 800-641-6996.
NOT FOR USE IN RESIDENTIAL LIVING
AREAS OR IN ENCLOSED SPACES WITHOUT
ADEQUATE VENTILATION. THIS HEATER IS
NOT FOR USE WHERE EXPOSED TO THE WEATHER, AND INDOOR
USE ONLY IN WELLVENTILATED AREAS. INDOOR USE PERMITTED
ONLY FOR: THE TEMPORARY HEATING OF ADEQUATELY VENTILATED
BUILDINGS OR STRUCTURES UNDER CONSTRUCTION, ALTERATION
OR REPAIR. This is an un-vented portable heater that uses air (Oxygen)
from within the area in which it is used. Failure to provide adequate
combustion and ventilation air will result in asphyxiation, carbon monoxide
poisoning, bodily injury or death. Refer to “Ventilation” on Page 6.
MODEL NUMBERS:
MH-80TBOA-OFR
Factory ID: 500
DANGER
DANGER
BATTERY OPERATED
KEROSENE RADIANT HEATER
User’s Manual & Operating Instructions
Sauk Rapids, MN 56379 USA • Toll Free [phone]
Fax: [phone] • Web: www.masterindustrialproducts.com • Email: [email protected]
© 2023 Pinnacle Climate Technologies, Inc. MARE-409
Master is a registered trademark of Pinnacle Climate Technologies, Inc.
U.S. Patent No. 9,644,863
Locating Your Serial Number:
Your serial number can be found on a blue label on the left side cover. It will begin with the letter “S”
followed by 9 digits. For Example: S160901126. Have your Serial Number ready before calling customer
service at 800-641-6996.

2
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Radiant Heater User’s Manual
NEVER LEAVE HEATER UNATTENDED WHILE BURNING
OR WHILE CONNECTED TO A POWER SOURCE
MASSACHUSETTS RESIDENTS: Massachusetts state law prohibits the use of this heater in
any building which is used in whole or in part for human habitation. Use of this heating device
in Massachusetts requires local fire department permit (M.G.L.C. 148, Section 10A).
NEW YORK CITY RESIDENTS: The New York City Fire Code prohibits the storage, handling
and use of kerosene fueled heaters for space heating. Any person violating that provision
may be punished by a fine up to $10,000 and a term of imprisonment of up to 6 months.
Look for this icon throughout the manual for helpful tips on how to assemble, use and
clean your OFR heater.
THE INSTALLATION OF THIS HEATER SHALL COMPLY WITH THE REGULATIONS OF THE
AUTHORITIES HAVING JURISDICTION AND CSA STANDARD B139.
WARNING: This product can expose you to chemicals, including leadand lead
compounds, whichareknown to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
DO NOT START THE HEATER WHEN EXCESS OIL HAS ACCUMULATED.
DO NOT START THE HEATER WHEN THE CHAMBER IS HOT.
WARNING
WARNING
FIRE, BURN, INHALATION AND EXPLOSION HAZARD. Keep com-
bustibles such as; building materials, paper or cardboard a safe dis-
tance away from the heater as recommended by these instructions.
Never use the heater in spaces which contain products such as; gasoline, solvents, paint
thinners, dust particles, volatile or airborne combustibles or any unknown chemicals. This is
an un-vented portable heater. It uses air (Oxygen) from the area in which it is used. Adequate
combustion and ventilation air must be provided. Refer to “Ventilation” on page 8. Bulk fuel
storage should be a minimum of 25 feet from heater.
WARNING
DO NOT OPERATE THIS HEATER UNTIL YOU HAVE READ AND
THOROUGHLY UNDERSTAND THESE SAFETY AND OPERATING
INSTRUCTIONS.
Failure to comply with the precautions and instructions provided with this heater can result in
death, serious bodily injury, property loss or damage from the hazards of fire, soot production,
explosions, burns, asphyxiation or carbon monoxide poisoning. Only persons who can read
and understand these instructions should use or service this heater.
WARNING
SAFETY INFORMATION
Safety Information......................................................2-3
Specifications ................................................................. 4
Features........................................................................... 4
What’s in the Box........................................................... 4
Assembly ......................................................................4-5
Operation .....................................................................6-7
Battery Operation Instructions................................... 8
Maintenance..............................................................9-10
Wiring Diagram ..............................................................11
Troubleshooting Guide ...............................................12
Exploded View..............................................................13
Parts List .........................................................................14
Limited Warranty...........................................................15
TABLE OF CONTENTS

3
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Radiant Heater User’s Manual
NEVER LEAVE HEATER UNATTENDED WHILE BURNING
OR WHILE CONNECTED TO A POWER SOURCE
ALWAYS use only the electrical power (voltage and
frequency) specified on the model plate of the heater.
ALWAYS use only three-prong, grounded outlet and
extension cord.
ALWAYS use only 14 AWG or better extension cord.
ALWAYS unplug the heater when not in use.
ALWAYS install the heater so that it is not directly
exposed to water spray, rain, dripping water, or wind.
NEVER use fuels such as gasoline, benzine, paint
thinners or other oil compounds in this heater.
NEVER refill the heater’s fuel tank while the heater
is operating or still hot. This heater is EXTREMELY
HOT while in operation.
NEVER block air outlet (front).
NEVER use duct work in front of heater.
NEVER move or handle heater while still hot.
NEVER transport heater with fuel in tank.
NEVER use with an external fuel tank.
Keep all combustible materials away from this heater.
Minimum Clearance From Combustibles
MH-80TBOA-OFR
Top 4 ft. (122 cm)
Sides 4 ft. (122 cm)
Front 8 ft. (244 cm)
ALWAYS locate heater on a stable and level surface.
If your heater is equipped with a thermostat, once it
is plugged in, it can start at anytime in accordance
with the thermostat setting.
Extreme caution is necessary when any heater is
used by or near children or persons with reduced
physical, sensory or mental capabilities.
Do not add fuel when the heater is running. Heater
should be re-started after 24 hours of operation.
RISK OF ELECTRIC
SHOCK!
WARNING
RISK OF BURNS,
FIRE AND
EXPLOSION!
WARNING
CAUTION! HOT
WHILE IN OP-
ERATION. DO NOT
TOUCH. KEEP CHILDREN, ANIMALS, CLOTHING
AND COMBUSTIBLES AWAY FROM HEATER.
WARNING
The products described in this manual are
kerosene direct-fired, forced air heaters. Kerosene
forced air heaters are primarily intended for use for
temporary heating of buildings under construction,
alteration or repair. Direct-fired means that all
of the combustion products of the heater enter
the heated space. This appliance is rated at 98%
combustion eciency, but does produce small
amounts of carbon monoxide.
Carbon monoxide is toxic. Humans can tolerate
only small amounts of carbon monoxide and so
precautions should be taken to provide proper
ventilation. Failure to provide proper ventilation in
accordance with the instructions in this manual can
result in death.
People with breathing problems should consult
a physician before using this heater. Early signs
of carbon monoxide poisoning resemble the
flu. Symptoms of improper ventilation/carbon
monoxide poisoning are:
Headache • Dizziness •Nausea • Dry Mouth
Sore Throat • Burning of Nose and Eyes
If you experience any of these symptoms:
GET FRESH AIR AT ONCE! Have your heater
serviced and check for proper ventilation. Some
people are more aected by carbon monoxide
than others. These include: pregnant women, those
with heart or lung problems, anemia or those under
the influence of alcohol or at high altitudes.
NOT FOR USE WHERE EXPOSED TO THE
WEATHER, INDOOR USE PERMITTED ONLY FOR:
The temporary heating of adequately ventilated
buildings or structures under construction,
alteration or repair! Provide at least a three
square foot (2,800 sq cm) opening of outside
air for every 100,000 BTU/Hr (29 kW) heater
rating. Refer to “Ventilation” on page 6 for further
instructions.
RISK OF INDOOR
AIR POLLUTION!
WARNING
CARBON
MONOXIDE
POISONING MAY
LEAD TO DEATH!
DANGER
SAFETY INFORMATION CONT.

4
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Radiant Heater User’s Manual
NEVER LEAVE HEATER UNATTENDED WHILE BURNING
OR WHILE CONNECTED TO A POWER SOURCE
SPECIFICATIONS
Model # MH-80TBOA-OFR
Rating: BTU/Hr / kW 80,000 / 23.4
Fuel Consumption: Gal./Hr / L/Hr 0.63 / 2.38
Fuel Tank Capacity: Gal. / L 4 / 15
Max Operating Hours 6
Volts: AC/Hz 120VAC / 60Hz
Amps 5
Heating Area: ft.22000
Battery Voltage 18VDC Nominal
Battery Amps 5
Pump Pressure PSI/BAR 120/8.27
Specifications subject to change without notice.
FEATURES
WHAT’S IN THE BOX
Tools Needed:
- Phillips Head Screw Driver
Figure 1 Figure 2
Attach the handle while still in the box for
easier unpacking (see Figures 1 and 2).
Carry Handle (1) Black Screws (2)
MH-80TBOA-OFR
Safety Guard
Handle
Battery (Not Included)
Fuel Tank
Power Cord
Fuel Gauge
Fuel Cap
Power Switch
Thermostat
Digital Readout

5
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Radiant Heater User’s Manual
NEVER LEAVE HEATER UNATTENDED WHILE BURNING
OR WHILE CONNECTED TO A POWER SOURCE
1. Remove existing screws from shell ring on
either side of heater (see Figure 3) .
2. Line up holes on heat shield with holes in
shell ring. Attach with screws removed in
step 1 (see Figures 4 and 5).
Heat Shield
ASSEMBLY
Figure 3
Figure 4
Figure 5
IMPORTANT: INSTALL HEAT SHIELD BEFORE
OPERATING YOUR 80TBOA-OFR HEATER
HEATER IS INTENDED FOR USE WITHOUT DUCTS. DO NOT
CONNECT TO DUCTS. DO NOT TAMPER WITH THE UNIT.
HAVE A COMPETENT SERVICEMAN MAKE ANY ADJUSTMENT
OR REPAIR. DO NOT OPERATE THE UNIT IN CLOSE PROXIMITY TO COMBUSTIBLE
SURFACES OR MATERIALS. ALLOW THE UNIT TO COOL BEFORE SHUT DOWN. REMOVE
BATTERY IF THE HEATER IS NOT IN USE.
WARNING
SAFETY INFORMATION CONT.

6
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Radiant Heater User’s Manual
NEVER LEAVE HEATER UNATTENDED WHILE BURNING
OR WHILE CONNECTED TO A POWER SOURCE
OPERATION
Fueling The Heater:
Kerosene
For optimal performance of this heater, it is
strongly suggested that Kerosene be used.
Kerosene has been refined to virtually eliminate
contaminants, such as sulfur, which can cause
a rotten egg odor during the operation of the
heater. Using diesel fuel can cause excess soot
production. Do not use Bio-Diesel as this fuel will
damage your heater’s seals and filter.
CSA certified for use with only No. 1 K kerosene
fuel. Factory Tested for use with Kerosene,
Diesel #1 and #2, Fuel oil #1 and #2, JP8 (Jet A
fuel)
- NEVER use fuel such as, benzene, alcohol,
white gas, camp stove fuel, paint thinners, or
other oil compounds in this heater. THESE ARE
VOLATILE FUELS THAT CAN CAUSE A FIRE
OR EXPLOSION.
- NEVER store Kerosene in the living space.
Kerosene should be stored in a well ventilated
area outside the living area.
- NEVER store Kerosene in direct sunlight or
near a source of heat.
- NEVER use Kerosene that has been stored
from one season to the next. Kerosene
deteriorates over time. OLD Kerosene WILL
NOT BURN PROPERLY IN THIS HEATER.
NOTE: Kerosene should only be stored in a blue
container that is clearly marked “Kerosene.”
Never store Kerosene in a red container. Red is
associated with gasoline.
– For optimal operation the pump pressure will
have to be adjusted dependent upon fuel type,
ambient temperature, and elevation. While
heater is operating, turn adjusting screw
clockwise to increase, counter-clockwise to
decrease pressure.
Ventilation:
- Risk of indoor air pollution and Carbon Monoxide
Poisoning. Use heater only in well ventilated
areas.
- Refer to Safety Information on pages 2-3 for
information about Carbon Monoxide Poisoning.
- ALWAYS provide a fresh air opening in the heated
space of at least 2,800 square centimeters (3 sq. ft)
for each 100,00 Btu/Hr. (29 kW) of heater output.
Provide a larger opening if more heaters are being
used.
Minimum Ventilation Opening Needed
MH-80TBOA-OFR
2.4 ft.2
2240 cm2
NEVER REFUEL
THIS HEATER
WHILE IT IS HOT
OR OPERATING. FIRE OR EXPLOSION
COULD RESULT.
DANGER
CARBON MONOXIDE POISONING MAY LEAD
TO DEATH!
DANGER
NEVER FILL THE
FUEL TANK IN-
DOORS. ALWAYS
FILL THE TANK OUTDOORS. BE SURE THAT
THE HEATER IS ON LEVEL GROUND WHEN
FUELING, AND NEVER OVERFILL THE
TANK.
CAUTION
DO NOT USE GAS-
OLINE OR CRANK-
CASE DRAININGS.
WARNING

7
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Radiant Heater User’s Manual
NEVER LEAVE HEATER UNATTENDED WHILE BURNING
OR WHILE CONNECTED TO A POWER SOURCE
OPERATION CONT.
Pre-Lighting Instructions:
Charge the Battery
Ensure battery is fully charged for best run time. Follow
battery manufactures instructions for use, charging and
storing. Heater does not charge battery
Over Discharge Protection
Heater has a built in battery protection circuit that will
shut the heater o to protect the battery from over
discharging.
Starting the Heater (Ignition):
1. Fill the tank with Kerosene or other approved
fuel until needle on fuel gauge points to “F”.
2. Replace fuel cap and tighten firmly.
3. Connect the heater to power source, either
approved battery or a three prong (grounded)
power source. You must use a three prong
(grounded) extension cord that is at least 6 feet
long and is a minimum of 14 AWG rating.
4. Turn thermostat knob to desired setting.
5. Move the power switch to the “On” position. The
power indicator light will illuminate and heater
will ignite.
NOTE: On first ignition or after refueling, you may
hear a grinding sound just before ignition. This is
the fuel pump removing the air from the fuel line.
Your heater will start up within seconds. If it does
not start repeat start-up procedures with fuel
gauge reading at least 1/2 tank.
NOTE: Smoking may occur on first ignition.
NOTE: The electrical components of these
heaters are protected by a fuse mounted in the
PC board. If the heater fails to ignite, check this
fuse first and replace if necessary. Also check the
power source to be sure the proper voltage is
being provided to the heater.
Stopping / Restarting Heater:
1. To stop the heater, move the power switch to the
“O” position. Combustion will stop and the
Cooling Cycle will begin and last approx. 5
mins.
When the Cooling Cycle is complete the fan
will stop running and it will be safe to unplug
the heater or disconnect the battery.
NOTE: Unplugging the heater or disconnecting
the battery before the Cooling Cycle has been
completed may cause overheating, possible
damage to the heater and heat plate.
NOTE: Allowing heater to run out of fuel while
in operation can cause damage to fuel pump
and fuel lines.
2. To restart the heater; wait 10 seconds and follow
ignition steps 1–5 above.
TIP: If the heater does not ignite, the thermostat may
be set too low. Turn the control knob to a higher
setting until the heater ignites. If the heater does not
ignite; move switch to “O” position, check steps 1-5
above and then move switch to “On” position.
IMPORTANT: Never store leftover kerosene or diesel
between seasons, using old fuel can damage heater.
Figure 10
Power Switch
Thermostat Knob
DO NOT disconnect
heater from power
source before
cooling cycle has been completed.
WARNING
Use only Master
approved batteries
—CONTACT YOUR
LOCAL SERVICE CENTER OR CALL 800-641-6996
FOR MORE INFORMATION
CAUTION
RISK OF FIRE! Never
transport heater with
battery attached
DANGER
RISK OF FIRE! REMOVE BATTERY FROM
HEATER WHEN NOT IN USE
DANGER
TIP: If the heater does not ignite; move
switch to “O” position, check steps 1-3
above and then move switch to “On” position.

8
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Radiant Heater User’s Manual
NEVER LEAVE HEATER UNATTENDED WHILE BURNING
OR WHILE CONNECTED TO A POWER SOURCE
WARNING: Battery requirements: The
batteries (Lithium-ion Battery Packs) used with
this machine must be certied products that
comply with local safety regulations.
WARNING: Charger requirements: Please
use only the charger specied by the battery
manufacturer for charging. Charging with
another battery pack may cause a re hazard.
WARNING: Do not ignite or overheat the
battery or equipment, it may cause an explosion
if it catches re or is higher than the battery’s
required limit temperature.
WARNING: It is strictly prohibited to use
damaged or illegally modied batteries for this
machine as a power source, which may cause
re, explosion, personal injury, property damage
and other hazards.
NOTE:
1. This product will not charge the battery.
Please remove the battery after using the
product. If you do not use it for a long time,
you need to charge the battery regularly to
avoid affecting the battery life.
2. If the existing battery cannot be installed with
the device, please check Local after-sales
solution.
BATTERY OPERATION INSTRUCTIONS
Adapter Part Number ASM-00040 ASM-00040 ASM-00038 ASM-00038 ASM-00039 ASM-00071
Manufacturer DEWALT®Milwaukee®BLACK+DECKER®Porter Cable®Makita®Mastercraft®
Model 20V Max. & FlexVolt, 18V M18 20V Max. 20V Max. 18V 20V Max.
Technical Spec. (AH) 4-12 4-12 4-12 4-12 4-12 4-12
Battery Watt/hr 80-240 72-216 80-240 80-240 72-216 80-240
Battery Models
DCB080, DCB200, DCB201,
DCB203BT, DCB203G,
DCB204, DCB204BT, DCB205,
DCB8205G, DCB206,
DCB207, DCB208, DCB210,
DCB230, DCB240, DCB404,
DCB406, DCB609, DCB612
48-11-1815, 48-11-1820,
48-11-1828, 48-11-1835,
48-11-1840, 48-11-1845,
48-11-1850, 48-11-1860,
48-11-1865, 48-11-1860,
48-11-1890, 48-11-1812
LBXR36, LBX1540,
LBXR2036, LBX2040,
LBX2540
PCC685,
PCC685L
BL1815N,
BL1820B,
BL1830,
BL1830B,
BL1840B,
BL1850B,
BL1860B
054-3124-0
054-7553-4
054-7557-6
Battery Certication UL UL UL UL UL UL
Battery Charger Models DCB1106, DCB1112 48-59-1811, 48-59-1810,
48-59-1802 BDCA202
PCC690L,
PCC691L,
PCC692L,
PCC695L,
PCC699L
DC18RC,
DC18RA,
DC18SD
054-3126-6
Battery Charger Certication UL UL UL UL UL UL
NOTE: Actual run time may vary due to battery condition and ambient temperature.
DEWALT®, Milwaukee®, BLACK+DECKER®, Porter Cable®, Makita®, and Mastercraft® are registered trademarks of their respective owners. Pinnacle Climate Technologies, Inc.
s not associated, afliated, licensed, or endorsed by DEWALT®, Milwaukee®, BLACK+DECKER®, Porter Cable®, Makita®, and Mastercraft®.
Figure 1 Figure 2
Battery Run Time Estimated
Battery Voltage 18/20
Battery Pack Amp Hour 4 5 6 8 9 12
Estimated Run Time (Hour) 1.7 2.1 2.6 3.4 3.9 5.1
If you intend to use a Milwaukee® battery you will have to
replace the battery connection terminals.
1. Make sure heater is not plugged into a power source.
2. Locate terminals within the battery connection port. (See
Figure 1)
3. Using a Phillips screwdriver, unscrew the screws
holding in current terminals by turning the screws
counterclockwise.
4. Replace terminals with terminals provided in the bag.
(See Figure 2)
5. Be sure to tighten screws to ensure a good connection.

9
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Radiant Heater User’s Manual
NEVER LEAVE HEATER UNATTENDED WHILE BURNING
OR WHILE CONNECTED TO A POWER SOURCE
MAINTENANCE
Long Term Storage:
1. Unscrew the fuel cap.
2. Using an approved siphon, remove the
Kerosene or diesel.
3. Using a small amount of Kerosene or diesel,
rinse and swirl the fuel inside the fuel tank
NOTE: NEVER MIX WATER WITH FUEL. It will
cause rust inside the tank.
4. Empty the tank completely.
IMPORTANT: Never store leftover Kerosene
between seasons, using old fuel can
damage heater.
Store Heater in a dry, well ventilated area.
-Be sure that the storage area is free of dust
and corrosive vapors. Repack the heater in the
original packaging and keep user’s manual in
an easily accessible place.
Service:
DO NOT TAMPER WITH THE UNIT. HAVE AN
EXPERIENCED SERVICEMAN MAKE ANY
NECESSARY ADJUSTMENT OR REPAIRS.
We suggest following a maintenance schedule as
follows:
FUEL / FUEL TANK:
Flush tank every 200 hours of operation or as
needed. DO NOT flush with water, use fresh
Kerosene only.
SPARK PLUG:
Clean and re-gap every 600 hours of operation
or replace as needed. After removing the Spark
Plug, clean the terminals with a wire brush.
Re-gap the terminals to 0.140” (3.5 mm)
(see Figure 12).
TIP: Follow the long term storage
instructions to ush the tank.
Figure 12
Never service heater
while it is plugged in
or hot!
WARNING

10
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Radiant Heater User’s Manual
NEVER LEAVE HEATER UNATTENDED WHILE BURNING
OR WHILE CONNECTED TO A POWER SOURCE
Service (Continued):
FAN BLADES:
The fan blades should be cleaned at least once
per heating season, depending on conditions.
Remove all accumulated dust and dirt with a
burst of condensed air (see Figure 13).
PRESSURE ADJUSTMENTS:
Proper pressure is dependent on the fuel type the
unit will be running. When smoking or non-ignition
occurs, remove the lower panel. Locate the Phillips
screw with a nut on the fuel pump to the left of the
fuel line. There is a small “P” next to the pressure
screw. The ideal pressure is 120 psi (8.43 kg/cm2).
If you are experiencing smoking or fuel dripping
from the unit, turn the screw clockwise 1/8 to 1/4
of a turn to increase the fuel pressure until the
unit is operating properly.
If you are experiencing extended flames from
the front of the unit, turn the screw 1/8 to 1/4 of a
turn counterclockwise to reduce the air pressure
until the unit is operating properly.
NOZZLES:
Nozzles should be cleaned or replaced at least
once per heating season. Contaminated fuel
could make this necessary immediately. To clean
dirt from nozzle, blow compressed air through
nozzle front. It may be necessary to soak nozzle
in clean Kerosene or diesel to help loosen any
particles (see Figure 14).
PHOTOCELL:
The photocell should be cleaned at least once
per heating season or more depending on
conditions. Use a cotton swab and water or
alcohol to clean the lens of the photocell.
Be certain to reinstall the photocell in proper
position as shown below (see Figure 15).
FILTERS:
The fuel filter should be cleaned at least twice
per heating season by rinsing it in clean Kerosene
or diesel. Contaminated or old fuel could make
cleaning necessary immediately. (see Figure 16).
MAINTENANCE CONT.
Figure 14
Figure 16
Figure 15
Figure 13
Diusion Cap
Diusion Cap
Gasket
Burner Head
Gasket
Burner Blade
Burner Body
Cooling Fan
Blower
Assembly Nozzle
Photocell
Fuel Line
Fuel Pump
Assembly
Intake Pipe
Fuel Filter