Matco Tools MSC4CAMO19 User manual

MSC4CAMO19 1 032519
MSC4CAMO19
Full Drawer Service Cart With Power Prep
Copyright © Professional Tool Products, 2019
All rights reserved
It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of the
device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or not
legible, contact Matco Tools for replacements. If the operator is not fluent in English, the product and safety instructions shall be read and
discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the operator
comprehends its contents. PLEASE NOTE: Loading cart beyond rated capacity may cause structural damage to the cart as well as personal
and /or property damage. Please educate your customers to the dangers of overloading.
• Read and follow all instructions in User's Manual.
• Do not load carts beyond rated capacity:
Overall Load Capacity ................................................. 600 LBS
Top Compartment ........................................................ 180 LBS
Drawers................................................................ 70 LBS each
PLEASE NOTE: Loading cart beyond rated capacity may cause structural damage to the cart as well as personal and/or property damage.
Please educate your customers to the "dangers of overloading".
• Lock lid and drawers before moving. • Apply brake on locking casters anytime cart is in place. • Do not pull cart. Push from handle on
end to move. • Units can tip or fall causing damage or personal injury. • Cart is designed to roll easily on flat surfaces and should not be
used on uneven or inclined surfaces. • Do not open more than one loaded drawer at a time. • Do not stand on or step in drawers. • Keep
children away from unit. • Wear gloves when lifting edges. • Before connecting to a power supply, always check to make sure the power
supply corresponds to the voltage required on the product. • Fully insert plug to reduce the risk of electric shock. • Always unplug when not
in use. • Disconnect power before installing or servicing. • Do not try to plug in unit or product when hands are wet or damp, or if standing
on a wet or damp surface or in water. • Never attempt to pick up unit or plugged in product that should fall in standing water. • This unit
is not waterproof and is intended for general use indoors. • Do not use in potentially dangerous locations, such as flammable or explosive
atmospheres. • Keep cord away from heat, oil, sharp edges or moving parts. • Failure to heed these warnings may result in personal injury
and/or property damage.
WARNING
WARNING: This product can expose you to chemicals including nickel, which is known to the State
of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.

MSC4CAMO19 2 032519
MSC4CAMO19
Full Drawer Service Cart With Power Prep
ASSEMBLY INSTRUCTIONS
SWIVEL CASTER with LOCKSWIVEL CASTER
M
A
T
C
O
T
O
O
L
S
M
A
T
C
O
T
O
O
L
S
Mount push handle/brackets assembly
(Part #12, 13) to the same side of the cart
as the swivel locking casters using the four
stove bolts, washers, and nuts provided.
Using 13mm socket completely tighten
all nuts.
#13
TOOLS NEEDED FOR ASSEMBLY:
• 13mm Socket or wrench
#12
#13

MSC4CAMO19 3 032519
MSC4CAMO19
Full Drawer Service Cart With Power Prep
HARDWARE SPECIFICATIONS
4 pcs.4 pcs. 4 pcs.
TROUBLESHOOTING
Problem: Drawers appear not to fit, do not slide in accurately
and bump the cart sides.
Solution: The roller bearing slides must be fully engaged into
the mounting slots on all drawers. They potentially could fall
out of position during shipment. Check the side of the cart to
determine which slide is out of position.
Remove the drawer that is out of position. The drawer is
removed by the two clips on the actual roller bearing slide.
Simply push the roller bearing slide back down into position.
Insert the drawer back onto the roller bearing slides.
Problem: Back Lock/Unlock Switch does not engage
the drawer.
Solution: The inside Lock/Unlock slide potentially could fall
out of its groove during shipment. Unscrew the four screws
that are holding the Lock/Unlock slide in place.
Once the screws are removed, simply place the latch back
onto the slide and tighten the four screws back down.
Mounting Slots
16 pcs 16 pcs 16 pcs
Handle Hardware
Caster Hardware

Also available:
RSRBSDET8PK Ball Bearing Slide Detents (Pk of 8)
RSBKP Black Touch Up Paint (1oz.)
MSC4FC Set of 2 Fixed 5" x 2" Casters (Optional - Not included)
(Incl. 16 Bolts, 16 Spring Washers, & 16 Flat Washers)
MSC4CAMO19 4 032519
MSC4CAMO19
Full Drawer Service Cart With Power Prep
No. Part No. Description Qty
1 RSLKB Lock with Keys 1
2 RSMSC4FDBP Set of 4 Bumpers (Including #17, (16) fasteners) 1
These bumpers are attached to the legs with fasteners and may not be
used on carts which originally did not use these fasteners because the
legs were not made to accommodate them.
3 MSC4FDP3BK Black 3" Drawer 3
4 MSC4FDP4BK Black 4" Drawer 2
5 MSC4FDP5BK Black 5" Drawer 1
6 RSSWCS 5" Swivel Non-Locking Caster / each 2
7 MSC4HC 6 Pc. set Chrome Drawer Handles 2
8 RSMSC4FDBK Caster Bolt Kit (M8 x 16) 1
9 RSSWLCS 5" Swivel Locking Caster / each 2
10 Frame 1
11 RSMSC4FDLMPBK Black Locking Mechanism (Excludes Lock) 1
No. Part No. Description Qty
12 RSMSC4HDL Push Handle 1
13 RSMSC4HB Handle Brackets/Pr. w/ hardware 1
14 RSMSC4FD7LK 7pc EVA Liner Set for Drawers and Top 1
15 RSGP Gas Piston/each 2
16 RSRBS Roller Bearing Slides/pair 6
17 RSFDFK Bumper Fastener (set of 4) 4
18 RSFDPCK Plastic Cap (set of 4) 1
19 MSC4FDLIDBK9 Black Lid 1
20 RS4RCP Rubber Cord Protector 1
Only items identified by part number are available separately.