Matco Tools MSC4R User manual
MSC4R / MSC4BK / MSC4BL / MSC4TI / MSC4SVA / MSC4SB 1 Rev. 10/17/14
MSC4R, -BK, -BL, -TI, -SVA, -SB
Deluxe Service Cart
Wash hands thoroughly after handling.
It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsi-
bility of the device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or prod-
uct labels are lost or not legible, contact Matco Tools for replacements. If the operator is not fluent in English, the product and
safety instructions shall be read and discussed with the operator in the operator's native language by the purchaser/owner or
his designee, making sure that the operator comprehends its contents. PLEASE NOTE: Loading cart beyond rated capacity may
cause structural damage to the cart as well as personal and /or property damage. Please educate your customers to the dangers
of overloading.
WARNING
Copyright © Professional Tool Products, 2014
All rights reserved
MSC4R / MSC4BK / MSC4BL / MSC4TI / MSC4SVA / MSC4SB 2 Rev. 10/17/14
MSC4R, -BK, -BL, -TI, -SVA, -SB
Deluxe Service Cart
Due to the weight of this cart we recommend that
work together on the assembly. This cart
weighs approximately 170 lbs; please use caution during
assembly.
Locate the key tied to the bottom tray. Using the key,
open the lid and remove the caster box from the
bottom drawer. Once removed, make sure all drawers
are completely closed and the inside lever is in the
locked position. Close the top lid and lock.
Lay out a work surface using the protective foam
provided. Once this surface is secure, gently turn the
cart onto its lid (logo will be facing the foam).
(Before assembling the legs, remove the cable tie
holding the bumper in place.) Insert the front leg
(Part #7), labeled FL or FR into top lip of the cart. Then
place the Front bumper (Part # 14 with Matco Logo)
over the leg aligning the center bolt holes. With holes
aligned, insert stove bolt (Part #1a) and finger
tighten with nyloc nut and washer.
Install back leg (Part #7) labeled BL or BR and bumper
(Part #14 without logo) following the same procedure
as above. Note: Make sure the back leg is inside the
hinge rivet. Otherwise the holes will not line up
during assembly!!!
Repeat steps 3 & 4 to mount the legs on the
opposite side.
Completely tighten the 8 bolts just inserted.
ASSEMBLY INSTRUCTIONS
7
7
MSC4R / MSC4BK / MSC4BL / MSC4TI / MSC4SVA / MSC4SB 3 Rev. 10/17/14
Insert bottom shelf (Part # 23) between the four legs,
flat side facing up towards the ceiling. Insert sixteen
stove bolts (Part #1a) and completely tighten.
Mounting casters: Put the four casters in place. The
two locking casters (Part #12) should be on one side
of the cart, and the two non locking casters (Part #10)
should be on the other
. Using the 16 bolts (Part #9), washers
and fasteners (located in separate caster bag), com-
pletely tighten the casters to the bottom tray using a
13mm socket and 14mm combination wrench for the
bolt head. (Note: Bolt head and one washer should be
on the inside of the bottom shelf, nyloc nut and one
washer will be on the caster side.)
Carefully turn cart onto its casters.
Open top lid using the key provided.
Mount push handle/bracket assembly (Parts #5 & 6)
to the same side of the cart as the locking casters,
using the four stove bolts (Part #1b) provided. Finger
tighten at this time.
Insert the 4 Stove bolts (Part #4) provided to the
opposite side of the cart. Note: This stove bolt is shorter
due to not having to pass through a handle or bumper.
Insert the remaining 8 stove bolts (Part #1a).
ASSEMBLY INSTRUCTIONS
MSC4R, -BK, -BL, -TI, -SVA, -SB
Deluxe Service Cart
10
• 2-14mmCombinationWrenches
• 13mmSocketorUniversalSocket
• 4"Extension
• 1/4"Ratchet
• #2PhillipsScrewdriver
(Step 11)
(Step 12)
5
MSC4R / MSC4BK / MSC4BL / MSC4TI / MSC4SVA / MSC4SB 4 Rev. 10/17/14
Using 13mm socket, completely tighten all fasteners!!
Insert spray can divider (Part #19) into provided cut
away on the bottom shelf (Part #23). (Optional)
ASSEMBLY INSTRUCTIONS
MSC4R, -BK, -BL, -TI, -SVA, -SB
Deluxe Service Cart
HARDWARE SPECIFICATIONS
TROUBLESHOOTING
Troubleshooting points during MSC4 Series Assembly:
Drawers appear not to fit, do not slide in accurately
and bump the cart sides.
The roller bearing slides must be fully engaged into
the mounting slots on all drawers. They could potentially fall
out of position while turning the cart on its lid or back onto
its caster.
Check the side of the cart to determine which slide is out
of position.
Remove the drawer that is out of position. The drawer is
removed by the two clips on the actual roller bearing slide.
Simply push the roller bearing slide back down into position.
Insert the drawer back onto the roller bearing slides.
Back Lock/Unlock Switch does not engage
the drawer.
The inside Lock/Unlock slide could potentially fall
out of its groove while turning the cart on its lid or back onto
its casters.
Unscrew the four screws that are holding the Lock/Unlock slide
in place.
Once the screws are removed, simply place the latch back onto
the slide and tighten the four screws back down.
MSC4R / MSC4BK / MSC4BL / MSC4TI / MSC4SVA / MSC4SB 5 Rev. 10/17/14
MSC4R, -BK, -BL, -TI, -SVA, -SB
Deluxe Service Cart
5
7
10
11
13
PART DRAWINGS
MSC4R / MSC4BK / MSC4BL / MSC4TI / MSC4SVA / MSC4SB 6 Rev. 10/17/14
13
10
7
5
3
11
17
MSC4R, -BK, -BL, -TI, -SVA, -SB
Deluxe Service Cart
PART DRAWINGS
MSC4R / MSC4BK / MSC4BL / MSC4TI / MSC4SVA / MSC4SB 7 Rev. 10/17/14
MSC4R, -BK, -BL, -TI, -SVA, -SB
Deluxe Service Cart
21 MSC4LD4R(red) 1 4"Drawer
MSC4LD4BK (black)
MSC4LD4BL (blue)
MSC4LD4TI (titanium)
MSC4LD4SVA (silver vein)
MSC4LD4SB (stealth black)
22 MSC4LD5R(red) 1 5"Drawer
MSC4LD5BK (black)
MSC4LD5BL (blue)
MSC4LD5TI (titanium)
MSC4LD5SVA (silver vein)
MSC4LD5SB (stealth black)
23 MSC4SR (red) 1
Bottom Shelf with Reinforcing Brackets
MSC4SBK (black)
MSC4SBL (blue)
MSC4STI (titanium)
MSC4SSVA (silver vein)
MSC4SSB (stealth black)
24 RSLMMRN (red) 1 Locking Mechanism (Excludes Lock)
RSLMMBKN (black)
RSLMMBLN (blue)
RSLMMTIN (titanium)
RSLMMSVAN (silver vein)
RSLMMSBN (stealth black)
25 RSMSC4JR(red) 2 "J"Channel
RSMSC4JBK (black)
RSMSC4JBL (blue)
RSMSC4JTI (titanium)
RSMSC4JSVA (silver vein)
RSMSC4JSB (stealth black)
26 RSMSC4CCPR (red) 1 Center Clip-On Pcs/Pair (Fit between 3"drawers)
RSMSC4CCPBK (black)
RSMSC4CCPBL (blue)
RSMSC4CCPTI (titanium)
RSMSC4CCPSVA (silver vein)
RSMSC4CCPSB (stealth black)
27 MSC4LIDR9 (red) 1 Lid
MSC4LIDBK9 (black)
MSC4LIDBL9 (blue)
MSC4LIDTI9 (titanium)
MSC4LIDSVA9 (silver vein)
MSC4LIDSB9 (stealth black)
*Available in RSMSC4BK Bolt Kit.
Also available: RSRBSDET8PK Ball Bearing Slide Detents (Package of 8).
RSMSC46LK 6 Piece Liner Kit
MSC4FC Setof2Fixed5"x2"Casters(Optional-NotIncluded)
RSMSC4RD Red Touch-Up Paint
RSBKP Black Touch-Up Paint
RSMSC4BLU Blue Touch-Up Paint
RSMSC4TI Titanium Touch-Up Paint
RSMSC4SBP Stealth Black Touch-Up Paint
Touch-Up Paint Not Available for Silver Vein
1a *32 M8x22 Bolt
1b *4 M8x28 Bolt
2 *72 M8 Washer
3 *56 M8 Locking Nut
4 *4 M8x22 Bolt
5 RSMSC4HB 1 Handle Brackets/Pair with Hardware
6 RSMSC4HDL 1 Handle
7 RSMSC4LGR (red) 4 Leg/each
RSMSC4LGBK (black)
RSMSC4LGBL (blue)
RSMSC4LGTI (titanium)
RSMC4LGSVA (silver vein)
RSMC4LGSB (stealth black)
8 RSMSC4SRPR (red) 2
Screwdriver/Prybar Holder/each
RSMSC4SRPBK (black)
RSMSC4SRPBL (blue)
RSMSC4SRPTI (titanium)
RSMSC4SRPSVA (silver vein)
RSMSC4SRPSB (stealth black)
9 *16 M8x16 Bolt (for casters)
10 RSSWCS 2 5"SwivelCaster/each
11 RSMSC4RPR (red) 2 Reinforced Piece /each
RSMSC4RPBK (black)
RSMSC4RPBL (blue)
RSMSC4RPTI (titanium)
RSMSC4RPSVA (silver vein)
RSMSC4RPSB (stealth black)
12 RSSWLCS 2 5"SwivelCasterwithlock/each
13 MSC4HC 1 6 Pc. set Chrome Handles
MSC4HBK 6 Pc. set Black Handles (Optional)
MSC4HBL 6 Pc. set Blue Handles (Optional)
MSC4HR 6 Pc. set Red Handles (Optional)
14 RSMSC4BP 1 Set of 4 Bumpers
15 *12 Screw for Drawer Handles
16 RSLKB 1 Lock with Keys
17 RSGP 2 Gas Piston /each
18 RSRBS 4 Roller Bearing Slides /pair (not shown)
19 RSMSC4SCDR (red) 1 Spray Can Divider
RSMSC4SCDBK (black)
RSMSC4SCDBL (blue)
RSMSC4SCDTI (titanium)
RSMSC4SCDSVA (silver vein)
RSMSC4SCDSB (stealth black)
20a MSC4LD3RL(red) 1 3"LeftDrawer
MSC4LD3BKL (black)
MSC4LD3BLL (blue)
MSC4LD3TIL (titanium)
MSC4LD3SVLA (silver vein)
MSC4LD3SBL (stealth black)
20b MSC4LD3RR(red) 1 3"RightDrawer
MSC4LD3BKR (black)
MSC4LD3BLR (blue)
MSC4LD3TIR (titanium)
MSC4LD3SVRA (silver vein)
MSC4LD3SBR (stealth black)
This manual suits for next models
5
Table of contents
Other Matco Tools Outdoor Cart manuals
Matco Tools
Matco Tools MSC4CAMO19 User manual
Matco Tools
Matco Tools Operating Instructions User manual
Matco Tools
Matco Tools MSC4RFA17 User manual
Matco Tools
Matco Tools MSC4BK40 User manual
Matco Tools
Matco Tools MSC4RFFDP18 User manual
Matco Tools
Matco Tools MSC4RQP User manual
Matco Tools
Matco Tools MSC4RFD User manual
Matco Tools
Matco Tools MSC4REDRAT User manual
Popular Outdoor Cart manuals by other brands
goliath
goliath PR-1 Assembly guide
Teknik
Teknik Craft 5417047 manual
Safavieh Furniture
Safavieh Furniture FOX2558A quick start guide
Harbor Freight Tools
Harbor Freight Tools BIGFOOT Owner's manual & safety instructions
InterMetro Ind.
InterMetro Ind. SECM 2430 Instructions for use
U-Line
U-Line H-8166 manual
