Matsusada Precision DOEF Series User manual

Instruction Manual
MODEL DOEF series
Communication Interface
-LGob option
-LUs1 option
Rev. 0.3
B/N 243.9.027 *243.9.027*

Note
All rights reserved.
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form, or by any means, mechanical, electronic, photocopying,
recording, or otherwise, without the prior written permission of Matsusada Precision.

No patent liability is assumed with respect to the use of the information contained herein.
Moreover, because Matsusada Precision is constantly striving to improve its high-quality
products, the information contained in this manual is subject to change without notice.
Every precaution has been taken in the preparation of this manual. Nevertheless,
Matsusada Precision assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting from the use of the information
contained in this publication.
Trademarks
Company names and product names in this document are the trademarks or registered
trademarks of their respective companies.
Warranty
◆For details, refer to the following website.
https://www.matsusada.com/support/manufacturer_warranty.html

i
DOEF series
Table of Contents
Feature and Specification...........................................................................................................................1
1
Feature ....................................................................................................................................................11-1 General....................................................................................................................................................11-2 External Appearance...............................................................................................................................21-3 USB Communication (-LUs1 option)....................................................................................................21-3-1 Optical Communication (-LGob option)................................................................................................31-3-2
Main Unit Setting ........................................................................................................................................42
Operation Setting.....................................................................................................................................42-1 Connection...............................................................................................................................................62-2
Checking Operation..................................................................................................................................113
Checking USB Operation (DC Voltage Output with Original Command of Matsusada Precision)..113-1 Checking Operation of Optical Communication (DC Voltage Output with Original Command of
3-2 Matsusada Precision)...........................................................................................................................12
Program....................................................................................................................................................134
Command Syntax..................................................................................................................................134-1 REN, GTL Commands and Unit Setting................................................................................................134-2 Character set of Command...................................................................................................................144-3 Original Command of Matsusada Precision..........................................................................................154-4 Parameter Range Used for Command..................................................................................................194-5 Original Command Reference...............................................................................................................204-6 SCPI Command.....................................................................................................................................414-7 SCPI Command Setting........................................................................................................................424-8 SCPI Command List..............................................................................................................................434-9 SCPI Command Reference.................................................................................................................554-10 Normal Operation.............................................................................................................................554-10-1 Sequence Program Operation.........................................................................................................664-10-2

1 Feature and Specification
1
DOEF series
Feature1-1This product has a feature of digital control via communication system of USB (-LUs1 option) and optical
communication (-LGob option).
Additionally, both Matsusada original command and SCPI commands are supported.
General1-2After unpacking, make sure all the following accessories are included with the main unit.
[Accessories]
□
Instruction Manual (this)
1
□
Optical fiber cable (for -LGob option)
1
Feature and Specification
1

1 Feature and Specification
2
DOEF series
External Appearance1-3 USB Communication (-LUs1 option)1-3-1
[600W Rear panel]
Exterior view B
[1.2 kW Rear panel]
USB serial number is provided with the sticker on the USB connector.
The USB serial number is DOEFXXXX. (XXXX is a four-digit number.)
Example: Sticker for USB serial number
The serial number of the connector is DOEF0001.
-LGob option connector
USB connector
USB connector
USB S/N DOEF0001

1 Feature and Specification
3
DOEF series
Optical Communication (-LGob option)1-3-2
[600W Rear panel]
[1.2 kW Rear panel]
IN OUT
(3) (2) (1)
(1) Optical fiber cable connector (OUT)
(2) Optical fiber cable connector (IN)
(3) Connected device setting switch
IN OUT
(3) (2) (1)
(1) Optical fiber cable connector (OUT)
(2) Optical fiber cable connector (IN)
(3) Connected device setting switch

2 Main Unit setting
4
DOEF series
Operation Setting2-1
The product has two communication system: USB and Optical communications.
Note
For details about the main unit setting, refer to DOEF series Instruction Manual [8-1 Communication Settings].
1. USB communication (-LUs1 option)
This product uses a USB serial converter made by FTDI, and the baud rate setting is required.
The baud rate is selected from 9600 bps, 19200 bps, 38400 bps.
The factory default setting is 9600 bps.
It corresponds to Matsusada Original Command as well as SCPI command.
The USB delimiter is CR.
2. Optical communication (-LGob option)
The baud rate setting is required.
The baud rate is selected from 9600 bps, 19200 bps, 38400 bps.
The UNIT number is selected from 0 to 31.
It corresponds to Matsusada Original Command as well as SCPI command.
The RS-232C delimiter is CR.
After the communication setting, be sure to turn off the power of the product and then, turn it on again to
restart. Changing the setting will be available after restarting it.
If you change the communication setting, be sure to turn off the power of the
product and then, turn it on again to restart. If not, the communication system may
not work properly.
Before connecting the communication cable, be sure to turn off the power off.
Main Unit Setting
2

2 Main Unit Setting
5
DOEF series
As for Optical communication (-LGob option), it is also necessary to configure the connected devices.
The setting is performed by the dip switches on the rear panel.
Set the switch to OFF when Matsusada product CO-G32, CO-RG, CO-HV, and USB-OPT are used to attach
the optical cable connector IN of DOEF series, or when -LGob option is used.
Set the switch to ON when Matsusada product CO-OPT2-25, CO-OPT2-9, or CO-OPT4-25 are used for the
connection.
In DOEF series with -LGob option, if you do not use remote control (to use local
control), be sure to turn off the dip switch. If not, it could cause malfunctions.
1 2 3 4 5 6 7 8
Not in use
Switch 1 to 7
Connected device
Switch 8
[OFF]
Connected device:
CO-G32/CO-RG/CO-HV/
USB-OPT/DOEF-LGob
[ON]
Connected device:
CO-OPT2-25/CO-OPT2-9/
CO-OPT4-25
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8

2 Main Unit Setting
6
DOEF series
Connection2-2
1. USB communication (-LUs1 option)
USB cable is used to connect the USB connector of the unit with a USB controller (such as computer).
USB controller
USB cable
Rear panel of DOEF main unit
(USB connector)

2 Main Unit Setting
7
DOEF series
2. Optical communication (-LGob option)
2-1) Connection of Optical RS-232C/RS-485 modules (Optical communication)
Optical RS-232C module
CO-OPT2-25 （D-Sub 25-pin）
CO-OPT2-9 （D-Sub 9-pin）
Optical RS-485 module
CO-OPT4-25 （D-Sub 25-pin）
Optical RS-232C/RS-485 module
・When you do not use the Optical fiber cable connector, be sure to attach the cover to it.
・This product has necessary protection functions, but there is a risk of malfunction if you
use it together with a high voltage power supply in that noise may occur on the AC input
line by the output short circuit in the high voltage power supply. Therefore, you should
have AC input line separately from the high voltage power supply.
ACAdapter
OUT IN
OUT IN
or
Optical fiber cable
or
Available up to 32 units
DOEF Rear panel
RS-232C Controller /
RS-485 Controller
DOEF Rear panel