Maxtang BYT60 User manual

BYT60 Motherboard User’s Manual Version 2.0
1
Chapter 1 Product Introduction
1.1 Motherboard Specification
Platform: Onboard Intel BayTrail-D Celeron Processor J1800, Core Frequency 2.41Ghz,
power consumption 10W
Onboard Intel Bay Trail-D Celeron Processor J1900, Core Frequency 2.00Ghz,
power consumption 10W
Memory: Single Channel DDR3L 1333Mhz, Up to 8GB system memory
Graphic: Integrated graphic processor - Intel HD graphic support
Storage: 2X SATA2.0, 1X mSATA via mini PCIe slot, SATA2 and mSATA either one, 1X
eMMC(optional)
USB: Maximum 8X USB ports with 1x USB3.0 included.
Display: 1x HDMI, 1x VGA, 1x dual-channel 24bit LVDS and dual display support
Ethernet: Onboard 2x Gigabyte internet controller RTL8111F, 1x RJ45 and 2x USB2.0
co-layout
Sound: Onboard integrated HD audio chipset ALC662 supports Speaker-out, MIC-in and
S/PDIF and amplifier
I/O: IT8786E support 6x serial COM, 1x LPT, COM2 can do eitherRS232 or RS485. IT8772E
support COM1 only.
Other I/O: 2x mini PCIe slots with either 1x mSATA and 1 slot for wifi, 3G/4G or 2x Mini
PCie/USB slots support WIFI plus 3G/4G module.
1x LPT; GPIO and 1x PS/2 for keyboard and mouse
Form Factor: 170mm x 170mm
Power supply: DC-IN 12V Power, and 1x 4pin ATX

BYT60 Motherboard User’s Manual Version 1.3
2
Chapter 2 Hardware Function
2.1 Board Placement
Please take care to connect external devices for as not to damage the board!
2.1.1 Jumper Function Setting
Before hardware device installation, please check following table.
Tip: How to identify jumper pin no., observe pin no.1 mark on the board, Mark No.1 or
bold strip or triangle symbol: look at the back, see rectangle pin no.1; all jumper pin no.1
JHDMI
LPT
Mini-PCIE
SIM CARD
Speaker
F-AUDIO
LVDS_ADJ
PS/2
JPOWER
2*COM
mSATA
USB2.0
DIMM
CLR_MOS
eMMC
2*SATA
2*PWSATA
COM3-6
JGPIO
JAT
USB2.0
LVDS or
EdDP
J2

BYT60 Motherboard User’s Manual Version 1.3
3
shows 1 white arrow sign
2.1.2 Memory Slot
Onboard 1x DDR3L 1333MHz SO-DIMM memory slot, memory capacity up to 8GB
2.1.3 Internal display Header (JHDMI, JVGA)
One 14pin JHDMI and one 12 pin JVGA pin
JHDMI：
Definition
Pin No
Definition
DVI1_DATA2_P
1
2
DVI1_DATA2_N
DVI1_DATA1_P
3
4
DVI1_DATA1_N
DVI1_DATA0_P
5
6
DVI1_DATA0_N
DVI1_CLK_P
7
8
DVI1_CLK_N
DVI1_SCL
9
10
DVI1_SDA
VGA_DATA_5V
11
12
GND
DVI1_DETECT
13
14
GND
JVGA：
Pin No
Definition
1
CRT_DDC_ DATA
2
CRT_DDC_ CLK
3
GND
4
VGA_B_R
5
GND
6
VGA_G_R
7
GND
8
VGA_R_R
9
GND
10
CRT_HSYNC1
11
CRT_VSYNC1
12
VGA_DVI_5V

BYT60 Motherboard User’s Manual Version 1.3
4
2.1.4 Internal Power Supply (PWR2)
Pin No
Definition
1
+12V
2
+12V
3
GND
4
GND
2.1.5 Internal USB pin (USB1, USB2)
Onboard USB header for USB2.0 port
USB1、USB2：
Definition
Pin No.
Definition
5V
1
2
5V
USB DATA-
3
4
USB DATA-
USB DATA+
5
6
USB DATA+
GND
7
8
GND
9
10
NUL
2.1.6 LAN
Onboard gigabyte internet controller chipset RTL8111F, Link LED flashes, Action
LED flashes when data transmission.
RJ45 LAN LED：RJ45 LAN LED Status
LILED (Green)
Function
ACTLED (Yellow)
Function
Flash Mode
Network Connected
Flashing
Data Transmitting

BYT60 Motherboard User’s Manual Version 1.3
5
2.1.7（FP_AUDIO，JAUD，JSPIF）Audio Header
Realtek ALC662 audio controller chipset, Green is the audio output port
(Speaker-Out), Pink is MIC-in audio input port; JAUD is audio amplifier and JSPIF is
fiber digital audio signal.
FP_AUDIO：Front Panel Audio (FP-Audio)
Definition
Pin No
管脚
Definition
MIC2-L
1
2
AGND
MIC2-R
3
4
AVCC
FRO-R
5
6
MIC2-JD
F-IO-SEN(AGNG)
7
8
NC
FRO-L
9
10
LIN2-JD
JAUD:
Pin No
Definition
1
L+
2
L-
3
R-
4
R+
JSPIF:
Pin No
Definition
1
+5V
2
SPDIF Out
3
GND

BYT60 Motherboard User’s Manual Version 1.3
6
2.1.8 LVDS ( JLVDS，LVDS_ADJ & J2 )
Dual-channel 24bit LVDS header, VCC of LVDS power cable supply can be choose by
J2 control, LVDS_ADJ use for LVDS back-light power control.
JLVDS1:
Definition
Pin No
Definition
VCC
1
2
VCC
VCC
3
4
GND
GND
5
6
GND
A_DATA0_DN
7
8
A_DATA0_DP
A_DATA1_DN
9
10
A_DATA1_DP
A_DATA2_DN
11
12
A_DATA2_DP
GND
13
14
GND
A_CLK_DN
15
16
A_CLK_DP
A_DATA3_DN
17
18
A_DATA3_DP
B_DATA0_DN
19
20
B_DATA0_DP
B_DATA1_DN
21
22
B_DATA1_DP
B_DATA2_DN
23
24
B_DATA2_DP
GND
25
26
GND
B_CLK_DN
27
28
B_CLK_DP
B_DATA3_DN
29
30
B_DATA3_DP
LVDS_ADJ：
Pin No
Definition
1
12V
2
12V
3
LCD_BKL_ON
4
LCD_BKL_ADJ
5
GND
6
GND

BYT60 Motherboard User’s Manual Version 1.3
7
J2：LVDS Power
Pin No
Setting
Function
1-2
Close
VCC(+3.3V)
3-4
Close
VCC(+5V)
5-6
Close
VCC(+12V)
Attention: You can choose 12V/5V/3.3V between the three flexible adjustments.
Customer according to the LVDS voltage specification, use the jumper cap to meet the
requirements of the VCC interface 2pin short (it is strictly forbidden to use 2 or more
interfaces in same time using the jumping Cap short)
2.1.9 eDP(EDp/LVDS、EDp/LVDS_ADJ、J2) Optional
eDP and LVDS could select either one only. Version and board functions need
to decided before production, can’t be used at the same time.
eDP(丝印：EDp/LVDS):
Defintion
PIN No.
Defintion
VCC
1
2
VCC
VCC
3
4
EDP_HPD
GND
5
6
GND
EDP_AUXN
7
8
EDP_AUXP
N/A
9
10
N/A
EDP_DATA0_P
11
12
EDP_DATA0_N
GND
13
14
GND
N/A
15
16
N/A
EDP_DATA1_P
17
18
EDP_DATA1_N
N/A
19
20
N/A
N/A
21
22
N/A
N/A
23
24
N/A
GND
25
26
GND
N/A
27
28
N/A
N/A
29
30
N/A
eDP Backlight（丝印：EDp/LVDS_ADJ）:
PIN
Definition
1
12V
2
12V

BYT60 Motherboard User’s Manual Version 1.3
8
3
LCD_BKL_ON
4
LCD_BKL_ADJ
5
GND
6
GND
eDP Power（丝印：J2）:
Pin
1-2
Close
VCC(+3.3V)
3-4
Close
VCC(+5V)
5-6
Close
VCC(+12V)
Serial COM（JCOM1 ，JCOM2，JCOM36，JCOM2_P，JCOM4_P）
Provides 6x COM supports RS232. COM1 and COM2 defines as industrial
definition; JCOM2 and JCOM4 provides 5V/12V by jumper.
JCOM1：
Definition
Pin No
Definition
DCD#
1
2
DSR#
RXD
3
4
RTS#
TXD
5
6
CTS#
DTR#
7
8
RI#
GND
9
10
JCOM2 RS232 or RS485, Pin Definition:
Pin No
RS232
RS485
1
DCD
DATA-
2
DSR
NC
3
RXD
DATA+
4
RTS
NC
5
TXD
NC
6
CTS
NC
7
DTR
NC
8
RI
NC
9
GND
GND
JCOM3 to JCOM6 :

BYT60 Motherboard User’s Manual Version 1.3
9
Definition
Pin No
Definition
DCD#
1
2
RXD
TXD
3
4
DTR#
GND
5
6
DSR#
RTS#
7
8
CTS#
RI#
9
10
DCD#
11
12
RXD
TXD
13
14
DTR#
GND
15
16
DSR#
RTS#
17
18
CTS#
RI#
19
20
DCD#
21
22
RXD
TXD
23
24
DTR#
GND
25
26
DSR#
RTS#
27
28
CTS#
RI#
29
30
DCD#
31
32
RXD
TXD
33
34
DTR#
GND
35
36
DSR#
RTS#
37
38
CTS#
RI#
39
40
JCOM2 ; JCOM4:
PIN No
Setting
Function
1-2
Close
5V
3-4
Close
RI
5-6
Close
12V
2.1.10 Parallel Port (LPT)
Onboard 1x 2x13pin LPT header

BYT60 Motherboard User’s Manual Version 1.3
10
LPT:
Definition
Pin No
Definition
STB
1
2
AFD
LPT_ PPD0
3
4
ERROR
LPT_ PPD1
5
6
INIT
LPT_ PPD2
7
8
SLIN
LPT_ PPD3
9
10
GND
LPT_ PPD4
11
12
GND
LPT_ PPD5
13
14
GND
LPT_ PPD6
15
16
GND
LPT_ PPD7
17
18
GND
ACK
19
20
GND
BUSY
21
22
GND
PE
23
24
GND
SLCT
25
26
NC
2.1.11 JGPIO
4 input and 4 Output
Definition
Pin No
管脚
Definition
GPI_S5_0
5_0
1
2
1.8V
GPI_S5_1
3
4
GPO_S5_6
GPI_S5_2
5
6
GPO_S5_7
GPI_S5_3
7
8
GPO_S5_8
GND
9
10
GPO_S5_9
2.1.12 SATA and mSATA (SATA1，mSATA，PWSATA1）
Provides 2x standard SATA2.0 port (SATA2 and mSATA either one) and 2x 4pin
SATA Power
PWSATA1：PWSATA1 Pin Definition
Pin No
Definition
1
+5V
2
GND
3
GND

BYT60 Motherboard User’s Manual Version 1.3
11
4
+12V
2.1.13 eMMC (Optional)
eMMC support UEFI operation system such as Windows 10 64bit, Windows 8
64bit and Linux 64bit.
2.1.14（MINI-PCIE,SIM1）Mini-PCIe
One mini PCI-e slot support WIFI module or 3G/4G Module with 1x SIM card slot.
2.1.15 PS/2 header
Pin No
Definition
1
+5V
2
KB_DATA
3
KB_CLK
4
MS_ DATA
5
MS_CLK
6
GND
2.1.16 Front Panel Power Pin Definition
Front control panel header is used to connect to the chassis front panel
established by the function buttons and LEDs.
JPOWER1：Power Pin
Definition
Pin No
Definition
HDD_LED+
1
2
PWR_LED+
HDD_LED-
3
4
PWR_LED-
RSTBTN+
5
6
PWR_ON+
RSTBTN-
7
8
PWR_ON-
NUL
9
10
2.1.17 Auto Power On (JAT)
JAT：
Setting
JAT
Close
auto power on

BYT60 Motherboard User’s Manual Version 1.3
12
2.1.18 CMOS Clear / Default as Setting
CMOS powered by the onboard button cell battery, clearing CMOS will lead to the
permanent elimination of system setup (Default as factory setting)
Steps:
1. Turn off your computer, disconnect the power supply
2. Use a jumper CAP shorts circuit function on JCOMS socket, holds for 3 to 5
seconds, then disconnect.
3. Starts the computer, press DEL button, enter into BIOS setting, reload optimal
defaults
4. Save and Exit
JCOMS:
Setting
JCMOS
Close
Clear CMOS setting
Please do not clear CMOS when computer is on, so as to damage the
motherboard!