Maxtang TL10 User manual

TL10 V1.0 User Manual
1
TL10 Motherboard
User Manual
（Version 1.0）
Version：
NO.
Description
Issue Date:
V1.0
Initial version
2021/4/9

TL10 V1.0 User Manual
2
Chapter 1 Product Introduction
1.1 Brief Introduction
The TL10 is an mITX motherboard based on the Intel Tiger Lake-U Platform.
1.2 Parameters
CPU：i7-1165G7—Quad Core Eight Threads, Maximum Turbo Frequency 4.7GHz ，TDP-up 28W
i5-1145G7-- Quad Core Eight Threads, Maximum Turbo Frequency 4.4GHz ，TDP-up 28W
i3-1115G4—Dual Core Four Threads, Maximum Turbo Frequency 4.1GHz ，TDP-up 28W
Celeron 6305-- Dual Core Dual Threads，1.8GHz，TDP-up 15W
Memory：Dual Channel SO-DIMM DDR4-3200, Up to 64GB
GPU：Integrated Graphics based on CPU，Display via 4xHDMI2.0
Storage：1 x M.2 Key M for 2280 SSD NVMe, 1x Standard SATA3.0
USB： 2xUSB3.0，2xUSB2.0（Rear I/O）； 4xUSB2.0（header）
Ethernet：2xGigabyte network card（intel i211）on board.
Audio：High-definition audio chip, supporting speaker-out, Mic-in (rear port), Line-out, Mic-in (front
on-board pin), and power amplifier (onboard pin, connecting passive horn)
COM：1xCOM header（default RS232, RS485/RS422 Optional）
Expansion：1xM.2 Key B for 4G/5G Module ，1xM.2 Key E（Type 2230，for Wi-Fi card and Bluetooth）
Other I/O： 1x PCIE2X Slot
Dimension：170mm x 170mm
Power：12V DC-in
Working Temperature：-20℃~60℃

TL10 V1.0 User Manual
3
1.3 Connector Diagram
DC_IN
HDMI12
HDMI34
USB3.0
USB2.0
LAN1
LAN2
Audio
FP-AUDIO
JAUD
PCIEX2
J2
J1
J3
SYS_FAN
COM1
JPOWER
USB2.0
USB2.0
LPC
SO-DIMM
CPU_FAN1
CPU
M.2 _SSD
M.2_WIFI
M.2_W5G
LAN_LED
PWSATA
SATA
PWR2

TL10 V1.0 User Manual
4
Chapter 2 Hardware
2.1 Jumper Setting
Please configure the jumpers according to your requirements before installing the hardware.
How to identify the first header of jumpers and pins: Observe the mark beside the jumper or pins and
find the header marked by “1” or bold line or triangular symbol. Or observe the rear panel and the
header with square solder pad is the first header.
2.2 Memory Slots
On-board 2 x SO-DIMM DDR4-3200 slots, supporting dual channels, maximum capacity 64 GB.
2.3 Display Interface
The board equipped with 4x HDMI2.0 ports, supporting multiple 4k displays.
2.4 Storage Interface（Screen Printing：SATA、M.2_N、PWSATA）
The board is equipped 1x M.2 Key M for 2280 SSD NVMe, 1x SATA.
PWSATA:（screen printing：PWSATA）
Pin
Signal
1
5V
2
GND
3
GND
4
VSY
（The output voltage is consistent with
the DC power supply）
2.5 Expansion Slots（Screen Printing：M.2_W5G、M.2_E、PCIEX2、
PWR_5G）
Screen printing M.2_E: M.2 Key E，Supporting NGFF WIFI Card and Bluetooth.
Screen printing PCIEX2：It can be used for expanded PCIe devices like networking cards and
graphics cards.
Screen printing M.2_W5S：M.2 Key B，Supporting 4G/5 Module with standard SIM Card slot; Please
set the corresponding module power supply voltage according to the screen printing PWR_5G pins,
While using 4G/5G modules.
Module Power Supply:（Screen Printing：PWR_5G）

TL10 V1.0 User Manual
5
Interface
Settings
Function
1-2
Close
Module Power Supply（3.3V）
2-3
Close
Module Power Supply（3.8V）
2.6 USB Interface
The board is equipped with 2 x USB3.0 (Rear)，2x USB2.0(Rear)，4x USB2.0 onboard Pins（distance
in between 2.54mm）。
USB1、USB2:(Screen Printing：F_USB1、F_USB2)
Signal
Pin
Signal
VCC 5V
1
2
VCC 5V
USB DATA-
3
4
USB DATA-
USB DATA+
5
6
USB DATA+
GND
7
8
GND
NC
9
10
N/A
2.7 LAN（Screen Printing：LAN_LED）
Applying high-performance Gigabit Ethernet control chip（intel i211）technology，it features 2xRJ45
interfaces, supports Magic packet wake up with UEFI PXE network boot. Please set the IPv4 PXE
Support to Enabled while using UEFI PXE network under the BIOS.
Interface LED Status Indicators：
LI_LED（Green）
Status
Function
ACT_LED（Orange）
Status
Function
Always on
Network Connected
Blinking
Data transfer
LAN_LED:（Screen Printing：LAN_LED）
Pin
Signal
1
LAN1_D+
2
LAN1_D-
3
LAN2_D-
4
LAN2_D+
2.8 Audio Interface（Screen Printing：FP_AUDIO、JAUD)
Realtek Audio controlling chip. The green interface is for audio output (Line-out), and the pink
interface is for Mic input (Mic-in). The JAUD pin is for the power amplifier.
FP_AUDIO：（Screen Printing ：FP_AUDIO）

TL10 V1.0 User Manual
6
Signal
Pin
Signal
MIC2-L
1
2
AGND
MIC2-R
3
4
AVCC（NC）
FRO-R
5
6
MIC2-JD
F-IO-SEN(AGND)
7
8
N/A
FRO-L
9
10
LIN2-JD
JAUD:（Screen Printing ：JAUD）
Pin
Signal
1
L+
2
L-
3
R-
4
R+
2.9 COM（Screen Printing ：COM1、J1、J2、J3)
The board equipped 1x COM port (internal headers with 2.54mm distances in between) RS232
default, RS485/RS422 optional.
COM1：（Screen Printing ：COM1）
Pin
RS232
RS485
RS422
1
DCD
DATA-
TX-
2
RXD
DATA+
TX+
3
TXD
(NC)
RX+
4
DTR
(NC)
RX-
5
GND
GND
GND
6
DSR
(NC)
(NC)
7
RTS
(NC)
(NC)
8
CTS
(NC)
(NC)
9
RI
(NC)
(NC)
COM1 Setting Mode（Screen Printing ：J1、J2、J3）
RS232
RS485
RS422
COM1
J1(1-3)(2-4) J2(1-3)(2-4)
J3(1-2)(3-5)
J1(3-5)(4-6)
J2(1-3)(2-4)
J3(3-4)(7-8)
J1(3-5)(4-6)
J2(3-5)(4-6)
J3(1-3)(5-6)

TL10 V1.0 User Manual
7
2.10 Board Power Supply（Screen Printing ：PWR1、PWR2）
Supports 12V DC-in power adapter or ATX 12V supplementary power (2x2 pin)
PWR1：12V DC-in power socket
PWR2：ATX12V Supplementary power supply socket（2x2PIN）
2.11 Switch panel pin（Screen Printing ：JPOWER）
The front control panel interfaces are to connect the functional buttons and indicators on the front
panel.
JPOWER(Screen Printing ：JPOWER)
Signal
Pin
Signal
HDD_LED+
1
2
PWR_LED+
HDD_LED-
3
4
PWR_LED-
RSTBTN-
5
6
PWR_ON+
RSTBTN+
7
8
PWR_ON-
NC
9
10
N/A
2.12 System Fan（Screen Printing ：SYSFAN）
The board provides one system fan socket default 12V power supply (5V Optional).
SYSFAN：（Screen Printing ：SYS_FAN）
Pin
Signal
1
GND
2
VCC
3
TAC
4
CTL
2.13 CPU FAN Socket（Screen Printing ：CPU_FAN）
The board provides a CPU Fan socket for cooling, default 5V power supply (12V Optional).
CPU_FAN:（Screen Printing ：CPU_FAN）

TL10 V1.0 User Manual
8
Pin
Signal
1
VCC
2
GND
3
TAC
4
CTL
CPU_FAN:（Screen Printing ：CPU_FAN）Standard definition
Pin
Signal
1
GND
2
VCC
3
TAC
4
CTL
2.14 CMOS Clearance/Retention（Screen Printing ：CLR_CMOS）
CMOS is powered by onboard button batteries. Clearing CMOS will permanently remove the
previous system settings and restore the board to the original (factory settings) system settings.
Step 1: Turn off the PC and disconnect the power adapter.
Step 2: Use the jumper cap to connect the 1st and 2nd header of CLR_CMOS for about 10
seconds, then disconnect.
Step 3: Plug the jumper cap into the 2nd or 3rd header of CLR_CMOS. (Please note: Connecting
the 1st and 2nd header: CLR_CMOS, Connecting the 2nd and 3rd header: Normal boot)
Step 4: When starting the device, press the <Del> button to enter the BIOS, load the optimal
default value, save, and exit the settings.
COMS(Screen Printing ：CLR_CMOS)
Pin
Settings
Function
1-2
Connect
Clear COMS
2-3
Open
Normal boot
Please do not clear COMS when the PC is connected to power in case any board damaging.