MD SPORTS DH14001 User manual

MODEL: DH14001
Please contact us before returning the product to the store.
Toll Free: 877-472-4296

LIMITED 90 DAYS WARRANTY
1
This product is covered by a limited warranty that is effective for 90 days
from the date of purchase. The warranty covers any defects in parts and
workmanship.
This Limited Warranty gives you specific legal rights and you may also have
other rights which very from one state (province) to another.
If, during the limited warranty period, a part is found to be defective or
breaks, we will offer replacement part at no cost to you, the customer. The
only exceptions to the warranty include main frames, tabletops, playing
surfaces, batteries or tools.
The above warranty will not apply in cases of damages due to improper
usage, alteration, misuse, abuse, accidental damage or neglect.
Attention: Since you build all tables upside down, please inspect table tops
and playing surfaces right away before putting together.
“PLEASE SAVE THESE INSTRUCTIONS
AND PURCHASE RECEIPT!”
A PURCHASE RECEIPT (or other proof of purchase date) will be required
before any warranty service is initiated. All requests for warranty service can
be submitted by email, in writing or by contacting our Consumer service
Department at:
TOLL FREE: 877-472-4296
WEBSITE: www.medalsports.com.tw
*Please do not call our 800 NUMBER as well as email us. This will result in
duplicate orders and charges will occur.
*Please note that all damaged table tops need to be returned to the store.
We do not replace any tabletops or playing surfaces.
PLEASE CONTACT US BEFORE RETURNING THE
PRODUCT TO THE STORE. THANK YOU VERY MUCH!

Phillips Screwdriver – Not Included
Standard (FlatHead Screwdriver) – Not Included
Allen Wrench - Included
TOOLS REQUIRED:
ASSEMBLY TIPS:
:

!



!
IMPORTANT NOTICE! Please contact us before returning the product to the store.
Please read the instructions carefully, and follow all assembly, operation or safety instructions
properly in order to avoid damage or injury. For the assembly, at least two adults are required.
Some figures or drawings may not look exactly like your product. Please read and understand
the text before beginning each assembly step.
1 -
2 -
1 - This product is intended for INDOOR use only.
2 - Please Do Not sit, climb or lean on the game table.
3 - Please Do Not drag the table when moving it in order to avoid the damaged on the legs.
4 - Please only use spray furniture polish to clean the exterior surfaces on the game table.
5 - This is not a child's toy, adult supervision is required for children playing this game.
Power Tools
-Set Low Torgue
High Torque
over tightened
CAUTION !
Electric Screwdrivers may be helpful during
assembly; however, please set a low torque
and use extreme caution.
2
Please Keep Your Instructions! Your Model number is necessary should you need to contact us.
Please read through this instruction manual book to familiarize yourself with all parts and
assembly steps. Kindly refer to the parts list below and be sure that all parts have been
included.
Although we are dedicated to giving our customers the best product possible, a question may
arise or parts may be missing. If you are missing parts, or, if you have any questions, please
contact our fast and friendly service centre on: 877-472-4296

3
Rod Stopper
20 Pieces Rod Bushing
10 Pieces Rod Handle
10 Pieces
30
40
Puck Catcher
with Sensor Wire
2 Pieces
Player Rod A
Player Rod C Player Rod D
Player Rod B
2 Pieces
Long Stick Blue Player
1 Piece Short Stick Blue Player
1 Piece
2 Pieces
26 27 28 29
31 32 33 34 35
36 37 38 39
Leg Leveler
4 Pieces
Apron Corner
2 Pieces
Apron Corner
with Scorer
2 Pieces
2 Pieces 4 Pieces
Red Goalie
1 Piece
Long Stick Red Player
1 Piece Medium Stick Red Player
3 Pieces
Blue Goalie
1 Piece Short Stick Red Player
1 Piece
Medium Stick Blue Player
3 Pieces
Control Box
1 Piece
Goalie Control
2 Pieces Gear
10 Pieces
M4x1/2"
Bolt
2 Pieces
Playfield
1 Piece
End Apron
2 Pieces 5/16" Flat Washer 24 Pieces
3x10mm Screw Silver
8 Pieces
4x40mm Screw
2Pieces
Leg End Panel
2 Pieces Leg Side Panel 2 Pieces
6
11
2 3 4 51
7 8 9 10
12 13 14 15
16 17 18 19 20
3.5x7mm Screw
4 Pieces
5/16"x1"Bolt
24 Pieces
Center Support
1 Piece Left Leg 2 Pieces
Right Leg
2 Pieces
Side Apron-A
1 Piece Side Apron-B 1 Piece
M4 Nut
2 Pieces 4x12mm Screw
24 Pieces
3x10mm Screw
20 Pieces
DH14001 PARTS LIST
21 22 23 24 25

4
Side PMMA
2 Pieces End PMMA 2 Pieces
Goal
2 Pieces Puck 2 Pieces
DH14001 PARTS LIST
51
Allen Wrench
1 Piece
42 43 44 4541
47 48 49 50
Long Puck Catcher
Wire with Sensor
1 Piece
Short Puck Catcher
Wire with Sensor
1 Piece Long Scorer Display
1 Piece Short Scorer Display
1 Piece
Pre-installed Pre-installed
Pre-installed Pre-installed
1) Require 3pcs AAA Batteries (Not included).
2) Do not mix old and new batteries.
3) Do not mix alkaline, standard (carbon zinc), or rechargeable (nickel-cadmium) batteries.

Allen Key
1 Piece
46
!
M4 Washer
2 Pieces

FIG.1
5
FIG.2
ASSEMBLY INSTRUCTIONS
1. Find a clean, level place to begin the assembly of your Rod Hockey table. The table will be assembled upside
down and then turned over on its legs once the assembly completed. This game table is heavy, and turning it
over will require at least two strong adults.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts List
page. Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work
surface.
3. Attach one Left Leg (#5) and Right Leg (#6) to the Side Apron-A (#1) using two Bolts (#11) and two Washers (#10)
per Leg. See FIG. 1.
FIG.2
4. Attach the End Apron (#7) to the Leg Assemble (previously assembled) using two Bolts (#11) and two Washers
(#10) per Leg. Do not tighten the bolts at this step. See FIG.2.
FIG.2
#11
#10
#11
#10
#1
#6
#5
FIG.1
#11
#10
#7

6
FIG.3
5. Slide the Playfield (#3) into the grooves of the End Aprons and Side Apron-A and attach the Side Apron-B(#2) to the
End Aprons (#7). See FIG 3.
#3
#2
FIG.3

7
FIG.4
6. Attach the Left Leg (#5) and Right Leg (#6) to the Apron using four Bolts (#11) and four Washers (#10) per Leg.
See FIG.4.
FIG.5
7. Insert Gear (#20) into the player groove on the underside of Playfield (#3). See FIG 5.
#20
#20
FIG.4
FIG.5
#11
#10
#11
#10
#5
#6
#11
#10

8
FIG.6
8. Slide all Player Rods (#24, #25, #26, #27) through the Rod holes in the End Apron.See FIG.6.
10. Push the Gear (#20) into the corresponding Player Rod using Spring Lock.See FIG.6A .
9. Attach the Rod Stopper (#21) to the Player Rod using one Screw (#17) per Rod Stopper. See FIG.6B.
11. Slide the Rod Bushing (#22) onto the Player Rod from outside of the main cabinet. See FIG.6.
12. Slide the Rod Handle (#23) onto the Player Rod after the Rod Bushing. See FIG.6.
FIG.6
FIG.6A
FIG.6B
Long Rod (24)
Long Rod (25)
Long Rod (25)
Long Rod (24)
Medium Rod (26)
Medium Rod (26)
Short Rod (27)
Short Rod (27)
Short Rod (27)
Short Rod (27)
#17
#17
#21
#22
#23
#20
Spring Lock

9
FIG.7
#18
#36
#11#10
#11
#10
#18
#13
#18
#18
FIG.7A
FIG.7
13. Slide the Goalie Control (#19) through the Goalie hole in the End Apron, secure the Goalie Control (#19) to the
underside of the Playfield (#3) using the Bolt (#15), Washer (#51) and Nut (#16).See FIG 7A.
14. Attach the Puck Catcher (#40) to the End Apron (#7) using four Screws (#18) per Puck Catcher. See FIG 7B.
15. Place the Center Support (#4) to the underside of Playfield (#3) using two Screws (#13).
FIG.8
FIG.7B
Step1
Step2
#19
#40
#18
#19
#15
#16
#4
#51
#39
#8
#8
#9
#9
16. Attach the Control Box (#36) to the
Side Apron-B (#2) using four Screws
(#18). See FIG 8.
17. Attach the Leg End Panel (#8)
between Left Leg and Right Leg using
six Screws (#18) per Leg End Panel.
18. Attach the Leg Side Panel (#9)
between Left Leg and Right Leg using
four Bolts (#11) and four Washers
(#10).
19. Attach the Leg Levelers (#39) at the
bottom of each leg.
20. Lift the table assembly from the floor
with two strong adults, turn it over,
and set table on its legs in the location
where you play. Go back and make
sure that all connections are tight.
HOLD TABLE CABINET DO NOT
HOLD THE
LEGS
DO NOT LEANTHE
TABLE ON ITS LEGS!
CAUTION: Two strong adults are recommended to turn the table over as shown.
1. Lift the table off the ground.
2. Turn the table over.
3. Place it on all four feet at the same time on the ground.

10
FIG.9
FIG.9
FIG.9B
FIG.9A
32
33
34
34
35
29
30 30
34
30 28
31
ORDER OF PLAYERS
(Overhead View)
= BLUE = RED
#41
#42
#43
#14
#14
#32
#33
#34
#31
#34
#34
#29
#30
#35
#28
#30
#30
21. Attach the Goal (#41) to the end of playfield using two Screws (#14) per Goal. See FIG.9.
22. Slide the Side PMMA (#42) into the slot pre-set on the Side Apron. See FIG.9.
23. Slide the End PMMA (#43) into the slot pre-set on the End Apron. See FIG.9.
24. Insert each Player (#28,#29,#30,#32, #33, #34) into each metal tap on the Gear (#20). See FIG.9, 9A and 9B.
25. Insert each Goalie (#31, #35) into each Goalie Control (#19). SeeFIG.9 and 9A.

11
#38
#37
#37
#38
FIG.10
Sensor Wire
Scorer Wire
Scorer Wire
FIG.1 0 A
Self-Stick Strap
FI G.1 0
26. Attach the Apron Corner (#37) to the top of Leg using two Screws (#12).See FIG.10.
27. Attach the Apron Corner with Scorer (#38) to the top of Leg using two Screws (#12).See FIG.10.
28. Insert the Sensor Wire from Puck Catcher (#40) into the Control Box (#36). See FIG. 10A.
29. Insert the Scorer Wire from Scorer into the Control Box (#36). See FIG.10A.
#12
NOW YOU ARE READY TO PLAY!
#36
Self-Stick Strap