MD SPORTS DH58101 User manual

MODEL: DH58101
Please contact us before returning the product to the store.
Toll Free: 877-472-4296

LIMITED 90 DAYS WARRANTY
1
This product is covered by a limited warranty that is effective for 90 days
from the date of purchase. The warranty covers any defects in parts and
workmanship.
This Limited Warranty gives you specific legal rights and you may also have
other rights which very from one state (province) to another.
If, during the limited warranty period, a part is found to be defective or
breaks, we will offer replacement part at no cost to you, the customer. The
only exceptions to the warranty include main frames, tabletops, playing
surfaces, batteries or tools.
The above warranty will not apply in cases of damages due to improper
usage, alteration, misuse, abuse, accidental damage or neglect.
Attention: Since you build all tables upside down, please inspect table tops
and playing surfaces right away before putting together.
“PLEASE SAVE THESE INSTRUCTIONS
AND PURCHASE RECEIPT!”
A PURCHASE RECEIPT (or other proof of purchase date) will be required
before any warranty service is initiated. All requests for warranty service can
be submitted by email, in writing or by contacting our Consumer service
Department at:
TOLL FREE: 877-472-4296
WEBSITE: www.medalsports.com.tw
*Please do not call our 800 NUMBER as well as email us. This will result in
duplicate orders and charges will occur.
*Please note that all damaged table tops need to be returned to the store.
We do not replace any tabletops or playing surfaces.
PLEASE CONTACT US BEFORE RETURNING THE
PRODUCT TO THE STORE. THANK YOU VERY MUCH!

Phillips Screwdriver – Not Included
Standard (FlatHead Screwdriver) – Not Included
Allen Wrench - Included
TOOLS REQUIRED:
ASSEMBLY TIPS:
:

!



!
IMPORTANT NOTICE! Please contact us before returning the product to the store.
Please read the instructions carefully, and follow all assembly, operation or safety instructions
properly in order to avoid damage or injury. For the assembly, at least two adults are required.
Some figures or drawings may not look exactly like your product. Please read and understand
the text before beginning each assembly step.
1 -
2 -
1 - This product is intended for INDOOR use only.
2 - Please Do Not sit, climb or lean on the game table.
3 - Please Do Not drag the table when moving it in order to avoid the damaged on the legs.
4 - Please only use spray furniture polish to clean the exterior surfaces on the game table.
5 - This is not a child's toy, adult supervision is required for children playing this game.
Power Tools
-Set Low Torgue
High Torque
over tightened
CAUTION !
Electric Screwdrivers may be helpful during
assembly; however, please set a low torque
and use extreme caution.
2
Please Keep Your Instructions! Your Model number is necessary should you need to contact us.
Please read through this instruction manual book to familiarize yourself with all parts and
assembly steps. Kindly refer to the parts list below and be sure that all parts have been
included.
Although we are dedicated to giving our customers the best product possible, a question may
arise or parts may be missing. If you are missing parts, or, if you have any questions, please
contact our fast and friendly service centre on: 877-472-4296

3
6
11
2 3 4 51
7 8 9 10
12 13 14 15
16 17 18 19 20
21 22 23 24 25
26 27 28 29 30
31 32 33
HOME VISITOR
TIME
Pre-installed
34 35
Pre-installed Pre-installed
Pre-installed
Board L Tube
2pcs
Board Tube
2pcs
Left Tube
1pc
Right Tube
1pc
Left L Tube
1pc
Right L Tube
1pc
Ramp U Tube
1pc
Allen Key
1pc
Backboard
1pc
M6 Washer
46pcs
M6 Nut
32pcs
Basketball 7” Dia.
4pcs
3.5 x 10mm Bolt
4pcs
Lock Pin
2pcs
Wrench
1pc
M6 x 20mm Bolt
16pcs M6 x 29mm Bolt
6pcs
M6 x 42mm Bolt
4pcs
M6 x 50mm Bolt
4pcs
M6 x 35mm Bolt
2pcs
Spring Lock
9pcs Plastic Pole Insert
2pcs
Electronic Scorer
Face Plate
1pc
Support Tube
2pcs
Mounting Tube
2pcs
Ramp Tube
2pcs
Ramp L Tube
2pcs
Switch Sensor
2pcs
Net
2pcs
Horizontal Tube
2pcs
Ball Ramp with
Side Netting
1pc
Electronic Scorer
1pc
Inflation Pump
with Needle
1pc
Ramp Support
Plate Metal
2pcs
Rim
2pcs
DH58101 PARTS LIST
WARNING:
!
1) Require 3pcs AA Batteries (Not included).
2) Do not mix old and new batteries.
3) Do not mix alkaline, standard (carbon zinc), or rechangeable (nickel-cadmium) batteries.

4
ASSEMBLY INSTRUCTIONS
FIG. 1 & 2
FIG. 3
1. Find a clean, level place to begin the assembly of your Basketball Game. We recommend that two adults work
together to assembly this basketball game.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts List
below.Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work
surface.
3. Attach the Board Tubes (#2) to the Left Tubes (#3) and Right Tubes( #4) using spring lock as shown in FIG.1.
4. Attach the Support Tubes (#7) to the Mounting Tubes (#8) using spring lock as shown in FIG.2
5. Attach the Left L Tube (#5) and Right LTube (#6) together using spring lock as shown in FIG.3
FIG. 1 FIG. 2
22
34
7
7
88
5
6
FIG. 3
Spring Lock
Spring Lock
Spring Lock

FIG. 4
8
7
5
6
8
7
5
6
4
3
27 22
26
22
24
22
6
27
24
27
22
2
27
26
22
5
6. Attach the Left and Right L Tubes (#5 and #6) to Left and Right Tubes (#3 and #4) using Bolts(#26), Washers (#22)
and Nuts(#27), and then attach the Left and Right L Tube (#5 and #6) to the Mounting Tube (#8) using Bolts (#26),
Washers (#22) and Nuts(#27) as shown in FIG.4A &4B.
7. Attach the Support Tube and Mounting Tube (#7 and #8) to the Board Tube(#2) using Bolts(#24), Washers (#22)
and Nuts(#27) as shown in FIG4C, repeat this step for other side. Note: Make sure the spring lock is face down.
8. Attach the Horizontal Tube (#12) to the Board Tube (#2)
using Bolts(#24), Washers(#22) and Nuts(#27) as shown
in FIG5. And then insert the Board L Tubes (#1) to the
Board Tube (#2) as shown in FIG.5.
FIG. 4
FIG. 5
FIG. 5
12
1
2
22
28
24
12
1
1
2
27
24
22
FIG. 4B
FIG. 4A
FIG. 4C
12
2
7

6
9. Attach the Ramp Tubes(#9) to the Left and Right L Tubes (#5 and #6) using Bolts(#32), Washers(#22) and Nuts
(#27) as shown in FIG 6.
10. Attach the Ramp L Tubes(#10) to the Ramp Tubes(#9) using spring lock as shown in FIG 7.
FIG. 6 & 7
9
5
6
9
FIG. 7
10
10
FIG. 6
#34
Spring Lock
#35
Plastic Pole Insert
22
27
22 32

7
FIG. 8 & 9
11. Attach the Rim Assemblies (#17) and Rim Support Plates (#18) to the Backboard (#21) using the Bolts (#23),
washers (#22) and Nuts (#27). And then attach the Switch Sensor (#15) to the Backboard (#21) using the
Bolts (#23), washers (#22) and Nuts (#27). Make sure that you use washer on both sides of the backboard as
shown in FIG. 8.
12. Attach Electronic Scorer Face Plate(#30) to Backboard and connect with the Electronic Scorer(#14) using Bolts
(#29) as shown in FIG. 9.
FIG. 9
FIG. 8
23
22
51 71
15
17
23
22
21
27 22 81
27 22 81
14
29
30
TIME
VISITOR
HOME

8
FIG. 10
FIG.10
FIG.10D
FIG.10C
FIG.10A
FIG.10B
11
13
13
13
11
10
13. Slide elastic straps and sleeve of Ball Ramp with Side Netting (#13) onto Board Tubes as shown in FIG. 10A & 10B.
14. Slide the Ramp U Tube(#11) into the sleeve of Ball Ramp with Side Netting(#13) as shown in FIG. 10C.
15. Connect the Ramp U Tube(#11) to the Ramp L Tube (#10) using spring lock as shown in FIG. 10D.
16. Slide the Horizontal Tube (#12) in front of the Ball Ramp with Side Netting(#13) and attach it to the Ramp U Tube
(#11) using Bolts(#24), Washers(#22) and Nuts(#27) as shown in FIG.10E.
FIG.10E
27
12 24
11
22
#34
Spring Lock

9
FIG. 11
17. With the help of another adult, Attach the Backboard(#21) to the Board Tubes(#1) using Bolts(#25), Washers(#22)
and Nuts(#27) as shown in FIG.11 A.
At each bottom hole of the backboard,attach the ramp tabs of Ball Return with Netting(#13) using Bolts(#25),
Washers(#22) and Nuts(#27) as shown in FIG.11 B .
18. Insert the Lock Pins (#33) to the Left and Right L Tubes (#5 and #6) as shown in FIG. 11C.
22
22 27
25
Ramp Tab
12
21
1
13
Back View.
FIG. 11B
FIG. 11C
FIG. 11A
33
14
FIG. 12
FIG. 12
FIG. 12A
Sensor wire
Electronic Scorer
Sensor wire
19. Connect the Sensor Wire of Switch Sensor to the Electronic Scorer (#14) as shown in FIG12.
ON/OFF
VISITOR