MedaCure SUPER LOW BED 3.9 User manual

USER MANUAL
This manual must be given to the Owner/User of
this bed and should be read carefully before putting
this product into use. Keep manual in an accessible
location for future reference.
MODEL # ULB3.9
www.medacureinc.com
© 2018
MADE IN CHINA

FEATURES AND FUNCTIONS
5 FUNCTION ELECTRIC S U P E R LOW BED
TRAVELS ALL THE WAY DOWN TO FLOOR LEVEL TO 3.9”
ULTIMATE FALL PREVENTION SOLUTION
WEIGHT CAPACITY: 450 LBS.
MATTRESSS DECK: 80” X 36”
QBAR ASSIST RAILS –SET OF 2 - OPTIONAL
Page 2
ACTUATOR COVER PROTECTOR
P REVENTS DAMAGE TO MOTORS & RISK OF OPERATION FAILURE
ENSURES A SAFE ENVIRONMENT FOR PATIENT AND STAFF
TRAVEL RANGE: 3.9”- 21”
PATIENT HANDSET: 5 FUNCTION WITH TRENDELENBURG
DURABLE EASY ROLL CASTERS: 3” WITH BRAKE MATTRESS
RETAINERS ON EACH CORNER - INCLUDED
SPLIT FRAME BED DECK
EXCELLENT RENTAL SOLUTION
FOR HASSLE FREE TRANSPORT
TOTAL FOLDED DIMENSIONS :
20” W X 36” L X 48.5” H

Page 3
5 Function Electric Bed Installation parts listed below as per Figure # 1:
Figure # 1
The bed is foldable for easy packing and shipping as per Figure # 2
Figure # 2
Bed head frame
Bed foot frame
Bed frame junction
block
Headboard
M10 Bolt, Spring
Washer, Flat Washer
Footboard
Packing connector
M10 Bolt, Spring
Washer, Flat Washer
Plastic Packing Cushion

Page 4
1. Installing the bed frame junction block
Unscrew the M10 bolt, take out the bed frame junction block from the 50 X 30 rectangular
tube. Insert the junction block (the end with threaded hole) into the 50 X 30 rectangular tube
of the bed head frame, matching the bolt hole and fasten by M10 bolt with φ10 spring
washer & φ10 flat washer. Do not over tighten the bolt, make sure the bed frame junction
block can still move. See Figure # 3.
Figure # 3
2. Unfold the folded bed frames as per Figure # 4
3. Connecting the middle frame
Insert the rectangular tube of the bed foot frame directly into the bed head frame junction
block, fasten with M10 bolt with φ10 spring washer & φ10 flat washer as per Figure # 4.
Figure # 4
M10 Bolt
φ10 flat washer
φ10 spring washer
M10 Bolt, Spring
Washer, Flat Washer

Page 5
4. Installing bed boards as per Figure # 5.
Figure # 5

Page 6
1
2
3
4
5. Connecting motor wires
Insert the motor wire joint into the wire connecting hole of control box as per Figure # 6.
Put the plastic cover on as per Figure # 7
Figure # 6
MOTOR ASSEMBLY
1. HEAD
2. FOOT
3. HI/LO & TREND –AT HEAD BOARD
4. HI/LO & TREND –AT FOOT BOARD
F
Figure # 7
Hand control wire
Motor wire for height
adjustment (Motor
in Foot Board)
Motor wire for height adjustment
(Motor in Head Board)
Motor wire for head part
Motor wire for foot part
POWER CORD

Page 7
IMPORTANT: TO AVOID DAMAGE TO THE POWER CORD, PLEASE MAKE SURE TO PLACE
THE POWER CORD THROUGH BOTH RINGS AS PER Figure #7A BEFORE
OPERATING THE BED.
Figure # 7A
Placing the power cord through the ring as per Figure # 7B:
Figure # 7B

Page 8
6. Operating the Remote Control / Hand Pendant
Ensure the power cord is connected properly. The patient can easily control all 5 functions by
using the remote hand pendant. This includes adjusting the bed height, raising/lowering the
head and foot sections, trendelenburg and reverse trendelenburg. Press the remote control
button until the ideal position is reached. See Figure #8.
Figure # 8
7. Bumper bar Installation
Attach the bumper onto the base of the head board section as per figures # 9
Figure 9
Raises bed head section
Raises bed foot section
Raises both bed head and
foot section –Auto Contour
Raises the entire bed
Lowers bed head section
Lowers bed foot section
Lower both bed head and foot section –
Auto Contour
Lowers the entire bed
Reverse Trendelenburg
Trendelenburg

Page 9
8. Bed Mattress Retainer Installation
Hang the Bed Mattress Retainer on the rectangular tubes of the mattress decks (see figures # 10)
Figure # 10
9. Rotating Assist Bar Installation & use
9.1.1 Insert the rail rods into the rail holes (see figures # 11) .
Figure # 11

Page 10
9.1.2 Secure the Rail rods to the bed by inserting the securing pins to the rod (see figures # 12) .
Figure # 12
9.2．Repeat the above installation, Step 1, to install the Pivot Assist Bar on the other side.
9.3．Pivot Assist Bar is used as an assist device to help the patient transfer in and out of bed
To raise the Assist Bar: Pull up the Assist Bar until it clicks in place. See “Assist Bar raising status” in
Figure # 13.
To lower the Assist Bar: Pull out the button (to unlock the Assist Bar) and push down the Assist Bar
towards the head or foot section. See “Assist Bar lowering status” in Figure # 13.
Figure # 13
Assist Bar raising position
Assist Bar lowering position
Pull out the button to
lower the Assist Bar

Page 11
Serial Number on Lower Bed Frame
When ordering parts please note bed’s model and serial numbers, located on the labels under the beddeck on
the lower bed frame on the length of the frame.
WARNING
Only use Medacure approved side rails with this bed. Other manufacturers assist bars and side rails may not
be compatible and can lead to entrapment issues or harm to patients.
Ensure mattress is the correct size for bed frame, mattress retainers are in place and the assist bars are
secured to frame to decrease the risk of entrapment.
© 2018
MADE IN CHINA