Medel SAMBA 2 GO User manual

SAMBA 2 GO
Quick Guide
AW52817_1.0 (English EU)

© 2020 MED‑EL Elektromedizinische Geräte GmbH. Revision 1.0 (03/2020). All rights reserved.
Table of Contents
SAMBA 2 GO .....................................1
Wearing SAMBA 2 GO ............................. 2
Switching SAMBA 2 GO On/Off ...................... 3
Pairing with your Audio Processor.................... 4
Adjusting Settings................................6
Streaming with SAMBA 2 GO........................7
Pairing with your Bluetooth Device ...................10
Making Phone Calls...............................12
Connecting via Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Using Remote Microphones ........................16
Charging SAMBA 2 GO ............................17
The SAMBA 2 GO Quick Guide is intended as an easy‑to‑use reference when
handling your SAMBA 2 GO. For detailed information on the intended use,
indications, contraindications, warnings and precautions of SAMBA 2 GO,
please refer to the instructions for use.

SAMBA 2 GO
Port for Audio Devices Neckloop
Microphone
Openings
Volume Buttons
Multi‑Function
Button
LED Status Indicator
(Blue, Green, Orange)
Port for FM Receiver
Reset Button
USB Port
1

Unplug one neckloop plug
and place the neckloop
loosely around your neck.
1Plug in both neckloop plugs
all the way.
2
SAMBA 2 GO
Wearing SAMBA 2 GO
In order to function correctly, your SAMBA 2 GO must be worn with
the neckloop around your neck. The neckloop is also the antenna.
2

To switch on SAMBA 2 GO, press
the multi‑function button until
the green LED turns on. This takes
approximately 2 seconds.
1To switch off SAMBA 2 GO,
press the multi‑function button
until the green LED fades off.
2
SAMBA 2 GO
Switching SAMBA 2 GO On/Off
3

SAMBA 2 GO
Pairing with your Audio Processor
You only have to pair your audio processor with SAMBA 2 GO once. After that, the
connection will be automatically established when both your audio processor and
your SAMBA 2 GO are switched on. If you are a bilateral user, you can pair both
audio processors at the same time.
Switch off your audio processor.
1Press the multi‑function button
on SAMBA 2 GO until the green
LED turns on. The green LED will
ash while searching for audio
processors nearby.
3
Make sure your SAMBA 2 GO
is switched off. Place it around
your neck.
2
4

During initial activation only, the blue LED will now ash to show
SAMBA 2 GO is ready to be paired with a Bluetooth device.
• If you want to pair a Bluetooth device, skip to step 3 on page 11.
• If you don’t want to pair a Bluetooth device right now, press the
multi‑function button to stop the blue LED ashing.
Switch on the audio processor while the
green LED is ashing.
4
Pairing is complete when the green LED
stops ashing, is illuminated for 5 seconds,
and then is no longer illuminated.
5
5

This function is not available while audio
streaming with SAMBA 2 GO.
SAMBA 2 GO
Adjusting Settings
SAMBA 2 GO helps you to make adjustments of your audio processor settings,
as pre‑dened by your audiologist or healthcare professional.
To adjust the volume, press the upper or lower
volume button once to change the volume
step by step. Alternatively, press and hold the
button until the desired volume is reached.
1
To mute or unmute the microphones, press
the upper and lower volume buttons together
for approximately 2 seconds.
2
To change program, press the multi‑function
button for 1–2 seconds and release. Repeat
until the desired program is reached.
3
6

Cable Connection Wireless Connection
SAMBA 2 GO
Streaming with SAMBA 2 GO
Phones, TVs, FM systems—you can connect SAMBA 2 GO to almost any device!
SAMBA 2 GO will then wirelessly send the audio from these devices straight to
your audio processor.
7

Audio Streaming Functions
These functions can be used while streaming from any device.
To start streaming from a Bluetooth device,
start audio playback on that device.
1
To start streaming from a device connected
by cable or an FM receiver, plug the device
into SAMBA 2 GO.
2
To stop streaming from any device or FM
receiver, press the multi‑function button for
1–2 seconds until the blue LED turns off.
3
8