Medisana TM 715 User manual
°F
°C
Explanation of symbols
IMPORTANT
Non-observance of these instructions can result in serious injury or damage to
the device.
WARNING
These warning note must be observed to prevent any injury to the user.
CAUTION
These notes must be observed to prevent any damage to the device.
NOTE
These notes give you useful additional information on the installation and
operation.
Device classication: type BF
LOT number
Manufacturer
Production date
Conforms to essential requirements of the Medical Device Directive 93/42/EEC.
Authorized Representative in European Community
The device should not be used after the end if the shown or the day
Protected against solid foreign objects of 12.5mm diameter and greater.
Protected against vertical falling water drops when the device is tilted up to 15°
Non-contact Infrared Thermometer TM 715
Instruction manual
48615_TM 715_manual_GB-TR_202011_L4
GB Safety Instructions
Important Information! Retain for future use! Read the instruction manual
carefully before using this device, especially the safety instructions, and keep the
instruction manual for future use, Should you give this device to another person,
it is vital that you also pass on these instructions for use.
Intended use:
The MEDISANA Non-contact Infrared Thermometer TM 715 is suitable to measure the body temperature of
humans. The measurement is carried out contact-free on the forehead.
Additionally the thermometer is suitable to measure the temperature of objects in the range of 0°C to 100°C.
• Only use the unit for the specic purpose described in the instruction manual. Any misuse will void the warranty.
• The unit is not designer for commercial use.
• Using this thermometer is no substitute for consulting a doctor. Consult your doctor in any case, before you start
a medicamentous treatment.
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before measuring
the temperature. Do not take a measurement within 30 minutes after physical exercise or after having a bath.
• This device is not designed to be used by persons(including children) with limited physical, sensory or mental
abilities, or by persons with insufcient experience and/or knowledge, unless under observation by a person
responsible for their safety, or unless they have been instructed in the use of the device.
• Children must be supervised to ensure that they do not play with the device.
• The temperature in the forehead and temple area differs from the internal temperature, which is taken orally or
rectally. Vasoconstriction, and effect which constricts the blood vessels and cools the skin, can occur during the
early stages of a fever. In this case, the temperature measured by the Non-contact Infrared Thermometer
TM 715 may be unusually low. If the measurement therefore does not match the patient’s own perception or is
unusually low, repeat the measurement every 15 minutes. As a reference, you can also measure the internal
body temperature using a conventional oral or rectal thermometer.
• It is recommended to perform at least 3 measurements with at least 1 minute interval. If the readings are
different; accept the highest value as reference value.
• A control measurement using a conventional thermometer is recommended in the following cases:
1. If the reading is surprisingly low
2. For new-born infants up to 100 days old
3. For children under three years of age who have a weakened immune system or who react unusually in the
presence or absence of fever
4. If you are using the thermometer for the rst time or want to familiarise yourself with it
• Babies’ skin reacts very quickly to the ambient temperature. Therefore, do not take their temperature with the
Non-contact Infrared Thermometer TM 715 during or after breastfeeding, because the skin temperature may
then be lower than the internal body temperature.
• There are no absolute body temperature standards. Keep record of your personal readings to allow your doctor
to judge if a medical treatment is necessary or not.
• Do not change the construction of the device and do not attempt to repair the unit yourself if a fault occurs or
the unit is damaged, as this will void the warranty. Contact your dealer and only have repairs carried out by
authorized service partners.
• Do not use the thermometer if it is damaged.
• Do not open up the device. It contains small parts which might be swallowed by children.
• Do not use the thermometer in damp environments.
• Do not immerse the thermometer in water or other liquids. It is not watertight.
• The sensor should be cleaned after each use, see the instructions in Cleaning and maintenance.
• Avoid direct nger contact with the sensor.
• Do not shake or tap the thermometer. Do not drop it.
• Protect the device from direct sunlight, extremely high or low temperatures, dirt and dust.
• If the thermometer is not going to be used for a long period, remove the batteries.
Unit and controls
Sensor
Scan-button
Illuminated LCD display
Battery compartment cover
Measurement of forehead temperature
°F Fahrenheit
°C Celsius
Temperature display
Memory display
Battery exchange symbole
q
w
e
r
t
y
u
i
o
a
Items supplied and packaging
Please check rst of all that the device is complete and is not damaged in any way. If in doubt, do not use it.
Send it to a service point.
The following parts are included:
•
1 MEDISANA Non-contact Infrared Thermometer TM 715
•
2 Batteries (AAA type, LR03) 1.5V
•
1 Instruction manual
The packaging can be reused or recycled. Please dispose properly of any packaging material no longer
required. If you notice any transport damage during unpacking, please contact your dealer without delay.
WARNING
Please ensure that polythene packing is kept away from the reach of children!
Risk of suffocation!
Taking a temperature reading – quickly and accurately!
The MEDISANA Non-contact Infrared Thermometer allows
precise, contact-free (approx. 1.5 to 5 cm distance) measurement
of body temperature. The temperature is taken above the
eye-brow between the forehead and the temple. The value
of the energy radiated there is measured and converted to a
temperature value. The reading is displayed within a few seconds.
The enables you, for example, to take babies’ temperature without
disturbing their sleep.
Getting started: Removing / Inserting batteries
For the use resp. if the battery symbol appears in the
display after a certain period of use, you must insert new batteries
before taking another measurement. Use two new 1.5 V batteries
(LR03, AAA).
Removal: Slide the lid of the battery compartment cover r
downwards as shown. Take out the batteries.
Insertion: Put in two new 1.5V-batteries (AAA, LR03). Make
sure the batteries are the right way around. Put the battery
compartment cover back on and move it upwards until it locks into
position.
WARNING
BATTERY SAFETY INFORMATION
•
Do not disassemble batteries!
•
Clean the battery and device contacts if necessary before putting in the batteries!
•
Remove discharged batteries from the device immediately!
•
Increased risk of leakage, avoid contact with skin, eyes and mucous membranes!
If battery acid comes in contact with any of these parts, rinse the affected area with copious
amounts of fresh water and seek medical attention immediately!
•
If a battery has been swallowed seek medical attention immediately!
•
Replace all of the batteries simultaneously!
•
Only replace with batteries of the same type, never use different types of batteries together or
used batteries with new ones!
•
Insert the batteries correctly, observing the polarity!
•
Keep the battery compartment well sealed!
•
Remove the batteries from the device if it is not going to be used for an extended period!
•
Keep batteries out of children’s reach!
•
Do not attempt to recharge these batteries! There is a danger of explosion!
•
Do not short circuit! There is a danger of explosion!
•
Do not throw into a re! There is a danger of explosion!
•
Keep unused batteries in their packaging away from metal objects in order to prevent short
circuiting!
•
Do not throw used batteries into the household refuse; put them in a hazardous waste container
or take them to a battery collection point, at the shop where they were purchased!
Before use
NOTES
For the most accurate reading:
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before
measuring the temperature.
• Do not take a baby’s temperature during or directly after breastfeeding.
• Do not use the thermometer in damp environments.
• Patients should not drink or eat directly before or during a measurement, and they should avoid any
physical exertion.
• Clean the area where you are taking the temperature and remove any dirt, hairs or sweat before
moving the sensor
q
to the measuring position.
• Do not remove the thermometer from the measuring position until it has beeped to signal the end of
the reading.
• If the sensor
q
becomes dirty during or after a reading, clean it with a cotton bud dipped in cleaning
alcohol before putting the thermometer away.
• Always take the temperature in the same place, because the readings will vary in different
environments.
The thermometer has been clinically tested, and its safety and accuracy inspected and conrmed,
provided it is used in accordance with these instructions.
Change the unit of measure
You can measure the temperature in ° Celsius or in ° Fahrenheit. Please proceed as follows to select the
unit of measure:
1. The device has to be switched off.
2. Press the SCAN-button w for approx. 8 seconds until the meausrement unit appears, then release.
3. Press the SCAN-button w again to change the unit of measurement to either °C or °F.
Measuring the body temperature
1. Turn on the thermometer by pressing SCAN-button w .
2. Point the senor q in the middle of the patient’s forehead at a
distance between 15 mm and max. 50 mm.
If the patient’s forehead has hair, sweat or dirt on it, remove
this rst so that the reading is as accurate as possible.
3. Press the SCAN-button w and release after approx. 1
second. You will hear a beep and the body temperature will be
displayed in the display e.
4. If the measurement result is below 32°C, a “Lo” sign will be
displayed follow by 2 consecutive beep sound. If measurement
reading is above 37.8°C, there will be 6 consecutive beep sound. If reading above 42.2°C is record, a “Hi”
sign will be displayed followed by 2 consecutive beep sound.
5. The measurement result will automatically be saved. After approx. 60 seconds without any further use the
thermometer will switch off automatically to save battery power.
15-50mm
15-50mm15-50mm15-50mm
Recalling stored data
The MEDISANA infrared thermometer can store up to 32 results.
You can call up your stored data with press on the SCAN-button wfor 4 seconds. The memory slot
number will be shown in the display e , together with the last stored temperature reading. With each
further press on the SCAN-button w , you can call up the previous results (memory slots 1 to 32).
Error messages
Display Problem Solution
Temperature taken is higher than
42.2°C / 108°F
Temperature taken is lower than
32°C / 89.6°F
Sensor not welded
EEPROM is abnormal
Low power
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Replace the batteries.
Cleaning and maintenance
•
The sensor is the most delicate part of the MEDISANA Non-contact Infrared Thermometer.
Protect it from dirt and damage. Clean the sensor with a cotton bus dipped in warm water or 70%
isopropyl alcohol.
•
Do not immerse the thermometer in water or any other liquid. It is not watertight.
•
To clean the thermometer, use a soft cloth slightly dampened with mild soapy water or 70% isopropyl
alcohol. Do not let water get into the unit. Only use the unit again when completely dry.
•
Never use aggressive cleaning agents, thinners, benzine or tough brushes.
•
Take care not to scratch the lens of the sensor, the display or the housing.
•
Do not use or store the unit in an environment where the ambient temperature or humidity is too high
or too low (see operating conditions in the “Technical specications” section), in direct sunshine, in
the vicinity of static electricity or in a dusty environment.
•
Remove the batteries if you do not wish to use the unit for an extended period of time.
Otherwise there is a danger that the batteries may leak.
•
If the thermometer is used as described in these instructions, no regular maintenance or calibration
is required.
Disposal
This product must not be disposed of together with domestic waste. All users are obliged to
hand in all electrical or electronic devices, regardless of whether or not they contain toxic
substances, at a municipal or commercial collection point so that they can be disposed of in
an environmentally acceptable manner. Please remove the batteries before disposing of the
device/unit. Do not dispose of old batteries with your household waste, but at a bettery
collection station at a recycling site or in a shop. Consult your municipal authority or your dealer for
information about disposal.
Technical specications
Name and model:
Display system:
Power supply
Measuring range:
Accuracy of measurement
(laboratory reading)
Display resolution
Memory capacity:
Auto. switch-off:
Operating temperature:
Storage/transport temperature:
Dimensions
Weight
Article no.:
EAN code:
MEDISANA Non-contact Infrared Thermometer TM 715
Digital display (LCD)
3V=, 2 x 1.5V batteries (type LR03, AAA)
32.0°C-42.2°C (89.6°F - 108°F)
±0.3°C(32.0°C ~ 42.2°C)
±0.5°F(89.6°F ~ 108°F) other range.
0.1°C (0.2°F)
up to 32 readings
approx. 1 minute after the last measurement
16°C-35°C(60.8°F - 95°F), rel. humidity of 15%-80%
-20°C-+55°C(-4°F - 131°F), rel. humidity of 15%-93%
approx. 144 x 101 x 36 mm
approx. 88 g (without batteries)
48615
40155 88 48615 9
In accordance with our policy of continual product improvement, we reserve the right to make
technical and optical changes without notice.
The unit is designed for home use only. For commercial use, a metrological inspection must
be carried out once every year. This calibration will be charged for and can be carried out by an
appropriate authority or an authorised service centre - in accordance with the regulations for users of
medical equipment.
Warranty and repair terms
Please contact your dealer or the service centre in case of a claim under the warranty, If you have to
return the unit, please enclose a copy of your receipt and state what the defect is.
The following warranty terms apply:
1. The warranty period for MEDISANA products is 3 years from date of purchase. In case of a
warranty claim, the date of purchase has to be proven by means of the sales receipt or invoice.
2. Defects in material or workmanship will be removed free of charge within the warranty period.
3. Repairs under warranty do not extend the warranty period either for the unit or for the replacement
parts.
4. The following is excluded under the warranty:
a . All damage which has arisen due to improper treatment, e.g. nonobservance of the user
instructions.
b . All damage which is due to repairs or tampering by the customer or unauthorised third parties.
c. Damage which has arisen during transport from the manufacturer to the consumer or during
transport to the service centre.
d. Accessories which are subject to normal wear and tear.
5. Liability for direct or indirect consequential losses caused by the unit are excluded even if the
damage to the unit is accepted as a warranty claim.
0123
0123
q w
e r
Error messages
Display Problem Solution
The temperature of the measuring
environment is too high.
The temperature of the measuring
environment is too low.
Decrease the temperature of the environment, keep
it within 16°C-35°C.
Increase the temperature of the environment, keep it
within 16°C-35°C.
0123
IP22
°F
°C
Explanation of symbols
IMPORTANT
Non-observance of these instructions can result in serious injury or damage to
the device.
WARNING
These warning note must be observed to prevent any injury to the user.
CAUTION
These notes must be observed to prevent any damage to the device.
NOTE
These notes give you useful additional information on the installation and
operation.
Device classication: type BF
LOT number
Manufacturer
Production date
Conforms to essential requirements of the Medical Device Directive 93/42/EEC.
Authorized Representative in European Community
The device should not be used after the end if the shown or the day
Protected against solid foreign objects of 12.5mm diameter and greater.
Protected against vertical falling water drops when the device is tilted up to 15°
Non-contact Infrared Thermometer TM 715
Instruction manual
48615_TM 715_manual_GB-TR_202011_L4
GB Safety Instructions
Important Information! Retain for future use! Read the instruction manual
carefully before using this device, especially the safety instructions, and keep the
instruction manual for future use, Should you give this device to another person,
it is vital that you also pass on these instructions for use.
Intended use:
The MEDISANA Non-contact Infrared Thermometer TM 715 is suitable to measure the body temperature of
humans. The measurement is carried out contact-free on the forehead.
Additionally the thermometer is suitable to measure the temperature of objects in the range of 0°C to 100°C.
• Only use the unit for the specic purpose described in the instruction manual. Any misuse will void the warranty.
• The unit is not designer for commercial use.
• Using this thermometer is no substitute for consulting a doctor. Consult your doctor in any case, before you start
a medicamentous treatment.
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before measuring
the temperature. Do not take a measurement within 30 minutes after physical exercise or after having a bath.
• This device is not designed to be used by persons(including children) with limited physical, sensory or mental
abilities, or by persons with insufcient experience and/or knowledge, unless under observation by a person
responsible for their safety, or unless they have been instructed in the use of the device.
• Children must be supervised to ensure that they do not play with the device.
• The temperature in the forehead and temple area differs from the internal temperature, which is taken orally or
rectally. Vasoconstriction, and effect which constricts the blood vessels and cools the skin, can occur during the
early stages of a fever. In this case, the temperature measured by the Non-contact Infrared Thermometer
TM 715 may be unusually low. If the measurement therefore does not match the patient’s own perception or is
unusually low, repeat the measurement every 15 minutes. As a reference, you can also measure the internal
body temperature using a conventional oral or rectal thermometer.
• It is recommended to perform at least 3 measurements with at least 1 minute interval. If the readings are
different; accept the highest value as reference value.
• A control measurement using a conventional thermometer is recommended in the following cases:
1. If the reading is surprisingly low
2. For new-born infants up to 100 days old
3. For children under three years of age who have a weakened immune system or who react unusually in the
presence or absence of fever
4. If you are using the thermometer for the rst time or want to familiarise yourself with it
• Babies’ skin reacts very quickly to the ambient temperature. Therefore, do not take their temperature with the
Non-contact Infrared Thermometer TM 715 during or after breastfeeding, because the skin temperature may
then be lower than the internal body temperature.
• There are no absolute body temperature standards. Keep record of your personal readings to allow your doctor
to judge if a medical treatment is necessary or not.
• Do not change the construction of the device and do not attempt to repair the unit yourself if a fault occurs or
the unit is damaged, as this will void the warranty. Contact your dealer and only have repairs carried out by
authorized service partners.
• Do not use the thermometer if it is damaged.
• Do not open up the device. It contains small parts which might be swallowed by children.
• Do not use the thermometer in damp environments.
• Do not immerse the thermometer in water or other liquids. It is not watertight.
• The sensor should be cleaned after each use, see the instructions in Cleaning and maintenance.
• Avoid direct nger contact with the sensor.
• Do not shake or tap the thermometer. Do not drop it.
• Protect the device from direct sunlight, extremely high or low temperatures, dirt and dust.
• If the thermometer is not going to be used for a long period, remove the batteries.
Unit and controls
Sensor
Scan-button
Illuminated LCD display
Battery compartment cover
Measurement of forehead temperature
°F Fahrenheit
°C Celsius
Temperature display
Memory display
Battery exchange symbole
q
w
e
r
t
y
u
i
o
a
Items supplied and packaging
Please check rst of all that the device is complete and is not damaged in any way. If in doubt, do not use it.
Send it to a service point.
The following parts are included:
•
1 MEDISANA Non-contact Infrared Thermometer TM 715
•
2 Batteries (AAA type, LR03) 1.5V
•
1 Instruction manual
The packaging can be reused or recycled. Please dispose properly of any packaging material no longer
required. If you notice any transport damage during unpacking, please contact your dealer without delay.
WARNING
Please ensure that polythene packing is kept away from the reach of children!
Risk of suffocation!
Taking a temperature reading – quickly and accurately!
The MEDISANA Non-contact Infrared Thermometer allows
precise, contact-free (approx. 1.5 to 5 cm distance) measurement
of body temperature. The temperature is taken above the
eye-brow between the forehead and the temple. The value
of the energy radiated there is measured and converted to a
temperature value. The reading is displayed within a few seconds.
The enables you, for example, to take babies’ temperature without
disturbing their sleep.
Getting started: Removing / Inserting batteries
For the use resp. if the battery symbol appears in the
display after a certain period of use, you must insert new batteries
before taking another measurement. Use two new 1.5 V batteries
(LR03, AAA).
Removal: Slide the lid of the battery compartment cover r
downwards as shown. Take out the batteries.
Insertion: Put in two new 1.5V-batteries (AAA, LR03). Make
sure the batteries are the right way around. Put the battery
compartment cover back on and move it upwards until it locks into
position.
WARNING
BATTERY SAFETY INFORMATION
•
Do not disassemble batteries!
•
Clean the battery and device contacts if necessary before putting in the batteries!
•
Remove discharged batteries from the device immediately!
•
Increased risk of leakage, avoid contact with skin, eyes and mucous membranes!
If battery acid comes in contact with any of these parts, rinse the affected area with copious
amounts of fresh water and seek medical attention immediately!
•
If a battery has been swallowed seek medical attention immediately!
•
Replace all of the batteries simultaneously!
•
Only replace with batteries of the same type, never use different types of batteries together or
used batteries with new ones!
•
Insert the batteries correctly, observing the polarity!
•
Keep the battery compartment well sealed!
•
Remove the batteries from the device if it is not going to be used for an extended period!
•
Keep batteries out of children’s reach!
•
Do not attempt to recharge these batteries! There is a danger of explosion!
•
Do not short circuit! There is a danger of explosion!
•
Do not throw into a re! There is a danger of explosion!
•
Keep unused batteries in their packaging away from metal objects in order to prevent short
circuiting!
•
Do not throw used batteries into the household refuse; put them in a hazardous waste container
or take them to a battery collection point, at the shop where they were purchased!
Before use
NOTES
For the most accurate reading:
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before
measuring the temperature.
• Do not take a baby’s temperature during or directly after breastfeeding.
• Do not use the thermometer in damp environments.
• Patients should not drink or eat directly before or during a measurement, and they should avoid any
physical exertion.
• Clean the area where you are taking the temperature and remove any dirt, hairs or sweat before
moving the sensor
q
to the measuring position.
• Do not remove the thermometer from the measuring position until it has beeped to signal the end of
the reading.
• If the sensor
q
becomes dirty during or after a reading, clean it with a cotton bud dipped in cleaning
alcohol before putting the thermometer away.
• Always take the temperature in the same place, because the readings will vary in different
environments.
The thermometer has been clinically tested, and its safety and accuracy inspected and conrmed,
provided it is used in accordance with these instructions.
Change the unit of measure
You can measure the temperature in ° Celsius or in ° Fahrenheit. Please proceed as follows to select the
unit of measure:
1. The device has to be switched off.
2. Press the SCAN-button w for approx. 8 seconds until the meausrement unit appears, then release.
3. Press the SCAN-button w again to change the unit of measurement to either °C or °F.
Measuring the body temperature
1. Turn on the thermometer by pressing SCAN-button w .
2. Point the senor q in the middle of the patient’s forehead at a
distance between 15 mm and max. 50 mm.
If the patient’s forehead has hair, sweat or dirt on it, remove
this rst so that the reading is as accurate as possible.
3. Press the SCAN-button w and release after approx. 1
second. You will hear a beep and the body temperature will be
displayed in the display e.
4. If the measurement result is below 32°C, a “Lo” sign will be
displayed follow by 2 consecutive beep sound. If measurement
reading is above 37.8°C, there will be 6 consecutive beep sound. If reading above 42.2°C is record, a “Hi”
sign will be displayed followed by 2 consecutive beep sound.
5. The measurement result will automatically be saved. After approx. 60 seconds without any further use the
thermometer will switch off automatically to save battery power.
15-50mm
15-50mm15-50mm15-50mm
Recalling stored data
The MEDISANA infrared thermometer can store up to 32 results.
You can call up your stored data with press on the SCAN-button wfor 4 seconds. The memory slot
number will be shown in the display e , together with the last stored temperature reading. With each
further press on the SCAN-button w , you can call up the previous results (memory slots 1 to 32).
Error messages
Display Problem Solution
Temperature taken is higher than
42.2°C / 108°F
Temperature taken is lower than
32°C / 89.6°F
Sensor not welded
EEPROM is abnormal
Low power
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Replace the batteries.
Cleaning and maintenance
•
The sensor is the most delicate part of the MEDISANA Non-contact Infrared Thermometer.
Protect it from dirt and damage. Clean the sensor with a cotton bus dipped in warm water or 70%
isopropyl alcohol.
•
Do not immerse the thermometer in water or any other liquid. It is not watertight.
•
To clean the thermometer, use a soft cloth slightly dampened with mild soapy water or 70% isopropyl
alcohol. Do not let water get into the unit. Only use the unit again when completely dry.
•
Never use aggressive cleaning agents, thinners, benzine or tough brushes.
•
Take care not to scratch the lens of the sensor, the display or the housing.
•
Do not use or store the unit in an environment where the ambient temperature or humidity is too high
or too low (see operating conditions in the “Technical specications” section), in direct sunshine, in
the vicinity of static electricity or in a dusty environment.
•
Remove the batteries if you do not wish to use the unit for an extended period of time.
Otherwise there is a danger that the batteries may leak.
•
If the thermometer is used as described in these instructions, no regular maintenance or calibration
is required.
Disposal
This product must not be disposed of together with domestic waste. All users are obliged to
hand in all electrical or electronic devices, regardless of whether or not they contain toxic
substances, at a municipal or commercial collection point so that they can be disposed of in
an environmentally acceptable manner. Please remove the batteries before disposing of the
device/unit. Do not dispose of old batteries with your household waste, but at a bettery
collection station at a recycling site or in a shop. Consult your municipal authority or your dealer for
information about disposal.
Technical specications
Name and model:
Display system:
Power supply
Measuring range:
Accuracy of measurement
(laboratory reading)
Display resolution
Memory capacity:
Auto. switch-off:
Operating temperature:
Storage/transport temperature:
Dimensions
Weight
Article no.:
EAN code:
MEDISANA Non-contact Infrared Thermometer TM 715
Digital display (LCD)
3V=, 2 x 1.5V batteries (type LR03, AAA)
32.0°C-42.2°C (89.6°F - 108°F)
±0.3°C(32.0°C ~ 42.2°C)
±0.5°F(89.6°F ~ 108°F) other range.
0.1°C (0.2°F)
up to 32 readings
approx. 1 minute after the last measurement
16°C-35°C(60.8°F - 95°F), rel. humidity of 15%-80%
-20°C-+55°C(-4°F - 131°F), rel. humidity of 15%-93%
approx. 144 x 101 x 36 mm
approx. 88 g (without batteries)
48615
40155 88 48615 9
In accordance with our policy of continual product improvement, we reserve the right to make
technical and optical changes without notice.
The unit is designed for home use only. For commercial use, a metrological inspection must
be carried out once every year. This calibration will be charged for and can be carried out by an
appropriate authority or an authorised service centre - in accordance with the regulations for users of
medical equipment.
Warranty and repair terms
Please contact your dealer or the service centre in case of a claim under the warranty, If you have to
return the unit, please enclose a copy of your receipt and state what the defect is.
The following warranty terms apply:
1. The warranty period for MEDISANA products is 3 years from date of purchase. In case of a
warranty claim, the date of purchase has to be proven by means of the sales receipt or invoice.
2. Defects in material or workmanship will be removed free of charge within the warranty period.
3. Repairs under warranty do not extend the warranty period either for the unit or for the replacement
parts.
4. The following is excluded under the warranty:
a . All damage which has arisen due to improper treatment, e.g. nonobservance of the user
instructions.
b . All damage which is due to repairs or tampering by the customer or unauthorised third parties.
c. Damage which has arisen during transport from the manufacturer to the consumer or during
transport to the service centre.
d. Accessories which are subject to normal wear and tear.
5. Liability for direct or indirect consequential losses caused by the unit are excluded even if the
damage to the unit is accepted as a warranty claim.
0123
0123
q w
e r
Error messages
Display Problem Solution
The temperature of the measuring
environment is too high.
The temperature of the measuring
environment is too low.
Decrease the temperature of the environment, keep
it within 16°C-35°C.
Increase the temperature of the environment, keep it
within 16°C-35°C.
0123
IP22
°F
°C
Explanation of symbols
IMPORTANT
Non-observance of these instructions can result in serious injury or damage to
the device.
WARNING
These warning note must be observed to prevent any injury to the user.
CAUTION
These notes must be observed to prevent any damage to the device.
NOTE
These notes give you useful additional information on the installation and
operation.
Device classication: type BF
LOT number
Manufacturer
Production date
Conforms to essential requirements of the Medical Device Directive 93/42/EEC.
Authorized Representative in European Community
The device should not be used after the end if the shown or the day
Protected against solid foreign objects of 12.5mm diameter and greater.
Protected against vertical falling water drops when the device is tilted up to 15°
Non-contact Infrared Thermometer TM 715
Instruction manual
48615_TM 715_manual_GB-TR_202011_L4
GB Safety Instructions
Important Information! Retain for future use! Read the instruction manual
carefully before using this device, especially the safety instructions, and keep the
instruction manual for future use, Should you give this device to another person,
it is vital that you also pass on these instructions for use.
Intended use:
The MEDISANA Non-contact Infrared Thermometer TM 715 is suitable to measure the body temperature of
humans. The measurement is carried out contact-free on the forehead.
Additionally the thermometer is suitable to measure the temperature of objects in the range of 0°C to 100°C.
• Only use the unit for the specic purpose described in the instruction manual. Any misuse will void the warranty.
• The unit is not designer for commercial use.
• Using this thermometer is no substitute for consulting a doctor. Consult your doctor in any case, before you start
a medicamentous treatment.
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before measuring
the temperature. Do not take a measurement within 30 minutes after physical exercise or after having a bath.
• This device is not designed to be used by persons(including children) with limited physical, sensory or mental
abilities, or by persons with insufcient experience and/or knowledge, unless under observation by a person
responsible for their safety, or unless they have been instructed in the use of the device.
• Children must be supervised to ensure that they do not play with the device.
• The temperature in the forehead and temple area differs from the internal temperature, which is taken orally or
rectally. Vasoconstriction, and effect which constricts the blood vessels and cools the skin, can occur during the
early stages of a fever. In this case, the temperature measured by the Non-contact Infrared Thermometer
TM 715 may be unusually low. If the measurement therefore does not match the patient’s own perception or is
unusually low, repeat the measurement every 15 minutes. As a reference, you can also measure the internal
body temperature using a conventional oral or rectal thermometer.
• It is recommended to perform at least 3 measurements with at least 1 minute interval. If the readings are
different; accept the highest value as reference value.
• A control measurement using a conventional thermometer is recommended in the following cases:
1. If the reading is surprisingly low
2. For new-born infants up to 100 days old
3. For children under three years of age who have a weakened immune system or who react unusually in the
presence or absence of fever
4. If you are using the thermometer for the rst time or want to familiarise yourself with it
• Babies’ skin reacts very quickly to the ambient temperature. Therefore, do not take their temperature with the
Non-contact Infrared Thermometer TM 715 during or after breastfeeding, because the skin temperature may
then be lower than the internal body temperature.
• There are no absolute body temperature standards. Keep record of your personal readings to allow your doctor
to judge if a medical treatment is necessary or not.
• Do not change the construction of the device and do not attempt to repair the unit yourself if a fault occurs or
the unit is damaged, as this will void the warranty. Contact your dealer and only have repairs carried out by
authorized service partners.
• Do not use the thermometer if it is damaged.
• Do not open up the device. It contains small parts which might be swallowed by children.
• Do not use the thermometer in damp environments.
• Do not immerse the thermometer in water or other liquids. It is not watertight.
• The sensor should be cleaned after each use, see the instructions in Cleaning and maintenance.
• Avoid direct nger contact with the sensor.
• Do not shake or tap the thermometer. Do not drop it.
• Protect the device from direct sunlight, extremely high or low temperatures, dirt and dust.
• If the thermometer is not going to be used for a long period, remove the batteries.
Unit and controls
Sensor
Scan-button
Illuminated LCD display
Battery compartment cover
Measurement of forehead temperature
°F Fahrenheit
°C Celsius
Temperature display
Memory display
Battery exchange symbole
q
w
e
r
t
y
u
i
o
a
Items supplied and packaging
Please check rst of all that the device is complete and is not damaged in any way. If in doubt, do not use it.
Send it to a service point.
The following parts are included:
•
1 MEDISANA Non-contact Infrared Thermometer TM 715
•
2 Batteries (AAA type, LR03) 1.5V
•
1 Instruction manual
The packaging can be reused or recycled. Please dispose properly of any packaging material no longer
required. If you notice any transport damage during unpacking, please contact your dealer without delay.
WARNING
Please ensure that polythene packing is kept away from the reach of children!
Risk of suffocation!
Taking a temperature reading – quickly and accurately!
The MEDISANA Non-contact Infrared Thermometer allows
precise, contact-free (approx. 1.5 to 5 cm distance) measurement
of body temperature. The temperature is taken above the
eye-brow between the forehead and the temple. The value
of the energy radiated there is measured and converted to a
temperature value. The reading is displayed within a few seconds.
The enables you, for example, to take babies’ temperature without
disturbing their sleep.
Getting started: Removing / Inserting batteries
For the use resp. if the battery symbol appears in the
display after a certain period of use, you must insert new batteries
before taking another measurement. Use two new 1.5 V batteries
(LR03, AAA).
Removal: Slide the lid of the battery compartment cover r
downwards as shown. Take out the batteries.
Insertion: Put in two new 1.5V-batteries (AAA, LR03). Make
sure the batteries are the right way around. Put the battery
compartment cover back on and move it upwards until it locks into
position.
WARNING
BATTERY SAFETY INFORMATION
•
Do not disassemble batteries!
•
Clean the battery and device contacts if necessary before putting in the batteries!
•
Remove discharged batteries from the device immediately!
•
Increased risk of leakage, avoid contact with skin, eyes and mucous membranes!
If battery acid comes in contact with any of these parts, rinse the affected area with copious
amounts of fresh water and seek medical attention immediately!
•
If a battery has been swallowed seek medical attention immediately!
•
Replace all of the batteries simultaneously!
•
Only replace with batteries of the same type, never use different types of batteries together or
used batteries with new ones!
•
Insert the batteries correctly, observing the polarity!
•
Keep the battery compartment well sealed!
•
Remove the batteries from the device if it is not going to be used for an extended period!
•
Keep batteries out of children’s reach!
•
Do not attempt to recharge these batteries! There is a danger of explosion!
•
Do not short circuit! There is a danger of explosion!
•
Do not throw into a re! There is a danger of explosion!
•
Keep unused batteries in their packaging away from metal objects in order to prevent short
circuiting!
•
Do not throw used batteries into the household refuse; put them in a hazardous waste container
or take them to a battery collection point, at the shop where they were purchased!
Before use
NOTES
For the most accurate reading:
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before
measuring the temperature.
• Do not take a baby’s temperature during or directly after breastfeeding.
• Do not use the thermometer in damp environments.
• Patients should not drink or eat directly before or during a measurement, and they should avoid any
physical exertion.
• Clean the area where you are taking the temperature and remove any dirt, hairs or sweat before
moving the sensor
q
to the measuring position.
• Do not remove the thermometer from the measuring position until it has beeped to signal the end of
the reading.
• If the sensor
q
becomes dirty during or after a reading, clean it with a cotton bud dipped in cleaning
alcohol before putting the thermometer away.
• Always take the temperature in the same place, because the readings will vary in different
environments.
The thermometer has been clinically tested, and its safety and accuracy inspected and conrmed,
provided it is used in accordance with these instructions.
Change the unit of measure
You can measure the temperature in ° Celsius or in ° Fahrenheit. Please proceed as follows to select the
unit of measure:
1. The device has to be switched off.
2. Press the SCAN-button w for approx. 8 seconds until the meausrement unit appears, then release.
3. Press the SCAN-button w again to change the unit of measurement to either °C or °F.
Measuring the body temperature
1. Turn on the thermometer by pressing SCAN-button w .
2. Point the senor q in the middle of the patient’s forehead at a
distance between 15 mm and max. 50 mm.
If the patient’s forehead has hair, sweat or dirt on it, remove
this rst so that the reading is as accurate as possible.
3. Press the SCAN-button w and release after approx. 1
second. You will hear a beep and the body temperature will be
displayed in the display e.
4. If the measurement result is below 32°C, a “Lo” sign will be
displayed follow by 2 consecutive beep sound. If measurement
reading is above 37.8°C, there will be 6 consecutive beep sound. If reading above 42.2°C is record, a “Hi”
sign will be displayed followed by 2 consecutive beep sound.
5. The measurement result will automatically be saved. After approx. 60 seconds without any further use the
thermometer will switch off automatically to save battery power.
15-50mm
15-50mm15-50mm15-50mm
Recalling stored data
The MEDISANA infrared thermometer can store up to 32 results.
You can call up your stored data with press on the SCAN-button wfor 4 seconds. The memory slot
number will be shown in the display e , together with the last stored temperature reading. With each
further press on the SCAN-button w , you can call up the previous results (memory slots 1 to 32).
Error messages
Display Problem Solution
Temperature taken is higher than
42.2°C / 108°F
Temperature taken is lower than
32°C / 89.6°F
Sensor not welded
EEPROM is abnormal
Low power
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Replace the batteries.
Cleaning and maintenance
•
The sensor is the most delicate part of the MEDISANA Non-contact Infrared Thermometer.
Protect it from dirt and damage. Clean the sensor with a cotton bus dipped in warm water or 70%
isopropyl alcohol.
•
Do not immerse the thermometer in water or any other liquid. It is not watertight.
•
To clean the thermometer, use a soft cloth slightly dampened with mild soapy water or 70% isopropyl
alcohol. Do not let water get into the unit. Only use the unit again when completely dry.
•
Never use aggressive cleaning agents, thinners, benzine or tough brushes.
•
Take care not to scratch the lens of the sensor, the display or the housing.
•
Do not use or store the unit in an environment where the ambient temperature or humidity is too high
or too low (see operating conditions in the “Technical specications” section), in direct sunshine, in
the vicinity of static electricity or in a dusty environment.
•
Remove the batteries if you do not wish to use the unit for an extended period of time.
Otherwise there is a danger that the batteries may leak.
•
If the thermometer is used as described in these instructions, no regular maintenance or calibration
is required.
Disposal
This product must not be disposed of together with domestic waste. All users are obliged to
hand in all electrical or electronic devices, regardless of whether or not they contain toxic
substances, at a municipal or commercial collection point so that they can be disposed of in
an environmentally acceptable manner. Please remove the batteries before disposing of the
device/unit. Do not dispose of old batteries with your household waste, but at a bettery
collection station at a recycling site or in a shop. Consult your municipal authority or your dealer for
information about disposal.
Technical specications
Name and model:
Display system:
Power supply
Measuring range:
Accuracy of measurement
(laboratory reading)
Display resolution
Memory capacity:
Auto. switch-off:
Operating temperature:
Storage/transport temperature:
Dimensions
Weight
Article no.:
EAN code:
MEDISANA Non-contact Infrared Thermometer TM 715
Digital display (LCD)
3V=, 2 x 1.5V batteries (type LR03, AAA)
32.0°C-42.2°C (89.6°F - 108°F)
±0.3°C(32.0°C ~ 42.2°C)
±0.5°F(89.6°F ~ 108°F) other range.
0.1°C (0.2°F)
up to 32 readings
approx. 1 minute after the last measurement
16°C-35°C(60.8°F - 95°F), rel. humidity of 15%-80%
-20°C-+55°C(-4°F - 131°F), rel. humidity of 15%-93%
approx. 144 x 101 x 36 mm
approx. 88 g (without batteries)
48615
40155 88 48615 9
In accordance with our policy of continual product improvement, we reserve the right to make
technical and optical changes without notice.
The unit is designed for home use only. For commercial use, a metrological inspection must
be carried out once every year. This calibration will be charged for and can be carried out by an
appropriate authority or an authorised service centre - in accordance with the regulations for users of
medical equipment.
Warranty and repair terms
Please contact your dealer or the service centre in case of a claim under the warranty, If you have to
return the unit, please enclose a copy of your receipt and state what the defect is.
The following warranty terms apply:
1. The warranty period for MEDISANA products is 3 years from date of purchase. In case of a
warranty claim, the date of purchase has to be proven by means of the sales receipt or invoice.
2. Defects in material or workmanship will be removed free of charge within the warranty period.
3. Repairs under warranty do not extend the warranty period either for the unit or for the replacement
parts.
4. The following is excluded under the warranty:
a . All damage which has arisen due to improper treatment, e.g. nonobservance of the user
instructions.
b . All damage which is due to repairs or tampering by the customer or unauthorised third parties.
c. Damage which has arisen during transport from the manufacturer to the consumer or during
transport to the service centre.
d. Accessories which are subject to normal wear and tear.
5. Liability for direct or indirect consequential losses caused by the unit are excluded even if the
damage to the unit is accepted as a warranty claim.
0123
0123
q w
e r
Error messages
Display Problem Solution
The temperature of the measuring
environment is too high.
The temperature of the measuring
environment is too low.
Decrease the temperature of the environment, keep
it within 16°C-35°C.
Increase the temperature of the environment, keep it
within 16°C-35°C.
0123
IP22
°F
°C
Explanation of symbols
IMPORTANT
Non-observance of these instructions can result in serious injury or damage to
the device.
WARNING
These warning note must be observed to prevent any injury to the user.
CAUTION
These notes must be observed to prevent any damage to the device.
NOTE
These notes give you useful additional information on the installation and
operation.
Device classication: type BF
LOT number
Manufacturer
Production date
Conforms to essential requirements of the Medical Device Directive 93/42/EEC.
Authorized Representative in European Community
The device should not be used after the end if the shown or the day
Protected against solid foreign objects of 12.5mm diameter and greater.
Protected against vertical falling water drops when the device is tilted up to 15°
Non-contact Infrared Thermometer TM 715
Instruction manual
48615_TM 715_manual_GB-TR_202011_L4
GB Safety Instructions
Important Information! Retain for future use! Read the instruction manual
carefully before using this device, especially the safety instructions, and keep the
instruction manual for future use, Should you give this device to another person,
it is vital that you also pass on these instructions for use.
Intended use:
The MEDISANA Non-contact Infrared Thermometer TM 715 is suitable to measure the body temperature of
humans. The measurement is carried out contact-free on the forehead.
Additionally the thermometer is suitable to measure the temperature of objects in the range of 0°C to 100°C.
• Only use the unit for the specic purpose described in the instruction manual. Any misuse will void the warranty.
• The unit is not designer for commercial use.
• Using this thermometer is no substitute for consulting a doctor. Consult your doctor in any case, before you start
a medicamentous treatment.
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before measuring
the temperature. Do not take a measurement within 30 minutes after physical exercise or after having a bath.
• This device is not designed to be used by persons(including children) with limited physical, sensory or mental
abilities, or by persons with insufcient experience and/or knowledge, unless under observation by a person
responsible for their safety, or unless they have been instructed in the use of the device.
• Children must be supervised to ensure that they do not play with the device.
• The temperature in the forehead and temple area differs from the internal temperature, which is taken orally or
rectally. Vasoconstriction, and effect which constricts the blood vessels and cools the skin, can occur during the
early stages of a fever. In this case, the temperature measured by the Non-contact Infrared Thermometer
TM 715 may be unusually low. If the measurement therefore does not match the patient’s own perception or is
unusually low, repeat the measurement every 15 minutes. As a reference, you can also measure the internal
body temperature using a conventional oral or rectal thermometer.
• It is recommended to perform at least 3 measurements with at least 1 minute interval. If the readings are
different; accept the highest value as reference value.
• A control measurement using a conventional thermometer is recommended in the following cases:
1. If the reading is surprisingly low
2. For new-born infants up to 100 days old
3. For children under three years of age who have a weakened immune system or who react unusually in the
presence or absence of fever
4. If you are using the thermometer for the rst time or want to familiarise yourself with it
• Babies’ skin reacts very quickly to the ambient temperature. Therefore, do not take their temperature with the
Non-contact Infrared Thermometer TM 715 during or after breastfeeding, because the skin temperature may
then be lower than the internal body temperature.
• There are no absolute body temperature standards. Keep record of your personal readings to allow your doctor
to judge if a medical treatment is necessary or not.
• Do not change the construction of the device and do not attempt to repair the unit yourself if a fault occurs or
the unit is damaged, as this will void the warranty. Contact your dealer and only have repairs carried out by
authorized service partners.
• Do not use the thermometer if it is damaged.
• Do not open up the device. It contains small parts which might be swallowed by children.
• Do not use the thermometer in damp environments.
• Do not immerse the thermometer in water or other liquids. It is not watertight.
• The sensor should be cleaned after each use, see the instructions in Cleaning and maintenance.
• Avoid direct nger contact with the sensor.
• Do not shake or tap the thermometer. Do not drop it.
• Protect the device from direct sunlight, extremely high or low temperatures, dirt and dust.
• If the thermometer is not going to be used for a long period, remove the batteries.
Unit and controls
Sensor
Scan-button
Illuminated LCD display
Battery compartment cover
Measurement of forehead temperature
°F Fahrenheit
°C Celsius
Temperature display
Memory display
Battery exchange symbole
q
w
e
r
t
y
u
i
o
a
Items supplied and packaging
Please check rst of all that the device is complete and is not damaged in any way. If in doubt, do not use it.
Send it to a service point.
The following parts are included:
•
1 MEDISANA Non-contact Infrared Thermometer TM 715
•
2 Batteries (AAA type, LR03) 1.5V
•
1 Instruction manual
The packaging can be reused or recycled. Please dispose properly of any packaging material no longer
required. If you notice any transport damage during unpacking, please contact your dealer without delay.
WARNING
Please ensure that polythene packing is kept away from the reach of children!
Risk of suffocation!
Taking a temperature reading – quickly and accurately!
The MEDISANA Non-contact Infrared Thermometer allows
precise, contact-free (approx. 1.5 to 5 cm distance) measurement
of body temperature. The temperature is taken above the
eye-brow between the forehead and the temple. The value
of the energy radiated there is measured and converted to a
temperature value. The reading is displayed within a few seconds.
The enables you, for example, to take babies’ temperature without
disturbing their sleep.
Getting started: Removing / Inserting batteries
For the use resp. if the battery symbol appears in the
display after a certain period of use, you must insert new batteries
before taking another measurement. Use two new 1.5 V batteries
(LR03, AAA).
Removal: Slide the lid of the battery compartment cover r
downwards as shown. Take out the batteries.
Insertion: Put in two new 1.5V-batteries (AAA, LR03). Make
sure the batteries are the right way around. Put the battery
compartment cover back on and move it upwards until it locks into
position.
WARNING
BATTERY SAFETY INFORMATION
•
Do not disassemble batteries!
•
Clean the battery and device contacts if necessary before putting in the batteries!
•
Remove discharged batteries from the device immediately!
•
Increased risk of leakage, avoid contact with skin, eyes and mucous membranes!
If battery acid comes in contact with any of these parts, rinse the affected area with copious
amounts of fresh water and seek medical attention immediately!
•
If a battery has been swallowed seek medical attention immediately!
•
Replace all of the batteries simultaneously!
•
Only replace with batteries of the same type, never use different types of batteries together or
used batteries with new ones!
•
Insert the batteries correctly, observing the polarity!
•
Keep the battery compartment well sealed!
•
Remove the batteries from the device if it is not going to be used for an extended period!
•
Keep batteries out of children’s reach!
•
Do not attempt to recharge these batteries! There is a danger of explosion!
•
Do not short circuit! There is a danger of explosion!
•
Do not throw into a re! There is a danger of explosion!
•
Keep unused batteries in their packaging away from metal objects in order to prevent short
circuiting!
•
Do not throw used batteries into the household refuse; put them in a hazardous waste container
or take them to a battery collection point, at the shop where they were purchased!
Before use
NOTES
For the most accurate reading:
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before
measuring the temperature.
• Do not take a baby’s temperature during or directly after breastfeeding.
• Do not use the thermometer in damp environments.
• Patients should not drink or eat directly before or during a measurement, and they should avoid any
physical exertion.
• Clean the area where you are taking the temperature and remove any dirt, hairs or sweat before
moving the sensor
q
to the measuring position.
• Do not remove the thermometer from the measuring position until it has beeped to signal the end of
the reading.
• If the sensor
q
becomes dirty during or after a reading, clean it with a cotton bud dipped in cleaning
alcohol before putting the thermometer away.
• Always take the temperature in the same place, because the readings will vary in different
environments.
The thermometer has been clinically tested, and its safety and accuracy inspected and conrmed,
provided it is used in accordance with these instructions.
Change the unit of measure
You can measure the temperature in ° Celsius or in ° Fahrenheit. Please proceed as follows to select the
unit of measure:
1. The device has to be switched off.
2. Press the SCAN-button w for approx. 8 seconds until the meausrement unit appears, then release.
3. Press the SCAN-button w again to change the unit of measurement to either °C or °F.
Measuring the body temperature
1. Turn on the thermometer by pressing SCAN-button w .
2. Point the senor q in the middle of the patient’s forehead at a
distance between 15 mm and max. 50 mm.
If the patient’s forehead has hair, sweat or dirt on it, remove
this rst so that the reading is as accurate as possible.
3. Press the SCAN-button w and release after approx. 1
second. You will hear a beep and the body temperature will be
displayed in the display e.
4. If the measurement result is below 32°C, a “Lo” sign will be
displayed follow by 2 consecutive beep sound. If measurement
reading is above 37.8°C, there will be 6 consecutive beep sound. If reading above 42.2°C is record, a “Hi”
sign will be displayed followed by 2 consecutive beep sound.
5. The measurement result will automatically be saved. After approx. 60 seconds without any further use the
thermometer will switch off automatically to save battery power.
15-50mm
15-50mm15-50mm15-50mm
Recalling stored data
The MEDISANA infrared thermometer can store up to 32 results.
You can call up your stored data with press on the SCAN-button wfor 4 seconds. The memory slot
number will be shown in the display e , together with the last stored temperature reading. With each
further press on the SCAN-button w , you can call up the previous results (memory slots 1 to 32).
Error messages
Display Problem Solution
Temperature taken is higher than
42.2°C / 108°F
Temperature taken is lower than
32°C / 89.6°F
Sensor not welded
EEPROM is abnormal
Low power
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Replace the batteries.
Cleaning and maintenance
•
The sensor is the most delicate part of the MEDISANA Non-contact Infrared Thermometer.
Protect it from dirt and damage. Clean the sensor with a cotton bus dipped in warm water or 70%
isopropyl alcohol.
•
Do not immerse the thermometer in water or any other liquid. It is not watertight.
•
To clean the thermometer, use a soft cloth slightly dampened with mild soapy water or 70% isopropyl
alcohol. Do not let water get into the unit. Only use the unit again when completely dry.
•
Never use aggressive cleaning agents, thinners, benzine or tough brushes.
•
Take care not to scratch the lens of the sensor, the display or the housing.
•
Do not use or store the unit in an environment where the ambient temperature or humidity is too high
or too low (see operating conditions in the “Technical specications” section), in direct sunshine, in
the vicinity of static electricity or in a dusty environment.
•
Remove the batteries if you do not wish to use the unit for an extended period of time.
Otherwise there is a danger that the batteries may leak.
•
If the thermometer is used as described in these instructions, no regular maintenance or calibration
is required.
Disposal
This product must not be disposed of together with domestic waste. All users are obliged to
hand in all electrical or electronic devices, regardless of whether or not they contain toxic
substances, at a municipal or commercial collection point so that they can be disposed of in
an environmentally acceptable manner. Please remove the batteries before disposing of the
device/unit. Do not dispose of old batteries with your household waste, but at a bettery
collection station at a recycling site or in a shop. Consult your municipal authority or your dealer for
information about disposal.
Technical specications
Name and model:
Display system:
Power supply
Measuring range:
Accuracy of measurement
(laboratory reading)
Display resolution
Memory capacity:
Auto. switch-off:
Operating temperature:
Storage/transport temperature:
Dimensions
Weight
Article no.:
EAN code:
MEDISANA Non-contact Infrared Thermometer TM 715
Digital display (LCD)
3V=, 2 x 1.5V batteries (type LR03, AAA)
32.0°C-42.2°C (89.6°F - 108°F)
±0.3°C(32.0°C ~ 42.2°C)
±0.5°F(89.6°F ~ 108°F) other range.
0.1°C (0.2°F)
up to 32 readings
approx. 1 minute after the last measurement
16°C-35°C(60.8°F - 95°F), rel. humidity of 15%-80%
-20°C-+55°C(-4°F - 131°F), rel. humidity of 15%-93%
approx. 144 x 101 x 36 mm
approx. 88 g (without batteries)
48615
40155 88 48615 9
In accordance with our policy of continual product improvement, we reserve the right to make
technical and optical changes without notice.
The unit is designed for home use only. For commercial use, a metrological inspection must
be carried out once every year. This calibration will be charged for and can be carried out by an
appropriate authority or an authorised service centre - in accordance with the regulations for users of
medical equipment.
Warranty and repair terms
Please contact your dealer or the service centre in case of a claim under the warranty, If you have to
return the unit, please enclose a copy of your receipt and state what the defect is.
The following warranty terms apply:
1. The warranty period for MEDISANA products is 3 years from date of purchase. In case of a
warranty claim, the date of purchase has to be proven by means of the sales receipt or invoice.
2. Defects in material or workmanship will be removed free of charge within the warranty period.
3. Repairs under warranty do not extend the warranty period either for the unit or for the replacement
parts.
4. The following is excluded under the warranty:
a . All damage which has arisen due to improper treatment, e.g. nonobservance of the user
instructions.
b . All damage which is due to repairs or tampering by the customer or unauthorised third parties.
c. Damage which has arisen during transport from the manufacturer to the consumer or during
transport to the service centre.
d. Accessories which are subject to normal wear and tear.
5. Liability for direct or indirect consequential losses caused by the unit are excluded even if the
damage to the unit is accepted as a warranty claim.
0123
0123
q w
e r
Error messages
Display Problem Solution
The temperature of the measuring
environment is too high.
The temperature of the measuring
environment is too low.
Decrease the temperature of the environment, keep
it within 16°C-35°C.
Increase the temperature of the environment, keep it
within 16°C-35°C.
0123
IP22
°F
°C
Explanation of symbols
IMPORTANT
Non-observance of these instructions can result in serious injury or damage to
the device.
WARNING
These warning note must be observed to prevent any injury to the user.
CAUTION
These notes must be observed to prevent any damage to the device.
NOTE
These notes give you useful additional information on the installation and
operation.
Device classication: type BF
LOT number
Manufacturer
Production date
Conforms to essential requirements of the Medical Device Directive 93/42/EEC.
Authorized Representative in European Community
The device should not be used after the end if the shown or the day
Protected against solid foreign objects of 12.5mm diameter and greater.
Protected against vertical falling water drops when the device is tilted up to 15°
Non-contact Infrared Thermometer TM 715
Instruction manual
48615_TM 715_manual_GB-TR_202011_L4
GB Safety Instructions
Important Information! Retain for future use! Read the instruction manual
carefully before using this device, especially the safety instructions, and keep the
instruction manual for future use, Should you give this device to another person,
it is vital that you also pass on these instructions for use.
Intended use:
The MEDISANA Non-contact Infrared Thermometer TM 715 is suitable to measure the body temperature of
humans. The measurement is carried out contact-free on the forehead.
Additionally the thermometer is suitable to measure the temperature of objects in the range of 0°C to 100°C.
• Only use the unit for the specic purpose described in the instruction manual. Any misuse will void the warranty.
• The unit is not designer for commercial use.
• Using this thermometer is no substitute for consulting a doctor. Consult your doctor in any case, before you start
a medicamentous treatment.
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before measuring
the temperature. Do not take a measurement within 30 minutes after physical exercise or after having a bath.
• This device is not designed to be used by persons(including children) with limited physical, sensory or mental
abilities, or by persons with insufcient experience and/or knowledge, unless under observation by a person
responsible for their safety, or unless they have been instructed in the use of the device.
• Children must be supervised to ensure that they do not play with the device.
• The temperature in the forehead and temple area differs from the internal temperature, which is taken orally or
rectally. Vasoconstriction, and effect which constricts the blood vessels and cools the skin, can occur during the
early stages of a fever. In this case, the temperature measured by the Non-contact Infrared Thermometer
TM 715 may be unusually low. If the measurement therefore does not match the patient’s own perception or is
unusually low, repeat the measurement every 15 minutes. As a reference, you can also measure the internal
body temperature using a conventional oral or rectal thermometer.
• It is recommended to perform at least 3 measurements with at least 1 minute interval. If the readings are
different; accept the highest value as reference value.
• A control measurement using a conventional thermometer is recommended in the following cases:
1. If the reading is surprisingly low
2. For new-born infants up to 100 days old
3. For children under three years of age who have a weakened immune system or who react unusually in the
presence or absence of fever
4. If you are using the thermometer for the rst time or want to familiarise yourself with it
• Babies’ skin reacts very quickly to the ambient temperature. Therefore, do not take their temperature with the
Non-contact Infrared Thermometer TM 715 during or after breastfeeding, because the skin temperature may
then be lower than the internal body temperature.
• There are no absolute body temperature standards. Keep record of your personal readings to allow your doctor
to judge if a medical treatment is necessary or not.
• Do not change the construction of the device and do not attempt to repair the unit yourself if a fault occurs or
the unit is damaged, as this will void the warranty. Contact your dealer and only have repairs carried out by
authorized service partners.
• Do not use the thermometer if it is damaged.
• Do not open up the device. It contains small parts which might be swallowed by children.
• Do not use the thermometer in damp environments.
• Do not immerse the thermometer in water or other liquids. It is not watertight.
• The sensor should be cleaned after each use, see the instructions in Cleaning and maintenance.
• Avoid direct nger contact with the sensor.
• Do not shake or tap the thermometer. Do not drop it.
• Protect the device from direct sunlight, extremely high or low temperatures, dirt and dust.
• If the thermometer is not going to be used for a long period, remove the batteries.
Unit and controls
Sensor
Scan-button
Illuminated LCD display
Battery compartment cover
Measurement of forehead temperature
°F Fahrenheit
°C Celsius
Temperature display
Memory display
Battery exchange symbole
q
w
e
r
t
y
u
i
o
a
Items supplied and packaging
Please check rst of all that the device is complete and is not damaged in any way. If in doubt, do not use it.
Send it to a service point.
The following parts are included:
•
1 MEDISANA Non-contact Infrared Thermometer TM 715
•
2 Batteries (AAA type, LR03) 1.5V
•
1 Instruction manual
The packaging can be reused or recycled. Please dispose properly of any packaging material no longer
required. If you notice any transport damage during unpacking, please contact your dealer without delay.
WARNING
Please ensure that polythene packing is kept away from the reach of children!
Risk of suffocation!
Taking a temperature reading – quickly and accurately!
The MEDISANA Non-contact Infrared Thermometer allows
precise, contact-free (approx. 1.5 to 5 cm distance) measurement
of body temperature. The temperature is taken above the
eye-brow between the forehead and the temple. The value
of the energy radiated there is measured and converted to a
temperature value. The reading is displayed within a few seconds.
The enables you, for example, to take babies’ temperature without
disturbing their sleep.
Getting started: Removing / Inserting batteries
For the use resp. if the battery symbol appears in the
display after a certain period of use, you must insert new batteries
before taking another measurement. Use two new 1.5 V batteries
(LR03, AAA).
Removal: Slide the lid of the battery compartment cover r
downwards as shown. Take out the batteries.
Insertion: Put in two new 1.5V-batteries (AAA, LR03). Make
sure the batteries are the right way around. Put the battery
compartment cover back on and move it upwards until it locks into
position.
WARNING
BATTERY SAFETY INFORMATION
•
Do not disassemble batteries!
•
Clean the battery and device contacts if necessary before putting in the batteries!
•
Remove discharged batteries from the device immediately!
•
Increased risk of leakage, avoid contact with skin, eyes and mucous membranes!
If battery acid comes in contact with any of these parts, rinse the affected area with copious
amounts of fresh water and seek medical attention immediately!
•
If a battery has been swallowed seek medical attention immediately!
•
Replace all of the batteries simultaneously!
•
Only replace with batteries of the same type, never use different types of batteries together or
used batteries with new ones!
•
Insert the batteries correctly, observing the polarity!
•
Keep the battery compartment well sealed!
•
Remove the batteries from the device if it is not going to be used for an extended period!
•
Keep batteries out of children’s reach!
•
Do not attempt to recharge these batteries! There is a danger of explosion!
•
Do not short circuit! There is a danger of explosion!
•
Do not throw into a re! There is a danger of explosion!
•
Keep unused batteries in their packaging away from metal objects in order to prevent short
circuiting!
•
Do not throw used batteries into the household refuse; put them in a hazardous waste container
or take them to a battery collection point, at the shop where they were purchased!
Before use
NOTES
For the most accurate reading:
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before
measuring the temperature.
• Do not take a baby’s temperature during or directly after breastfeeding.
• Do not use the thermometer in damp environments.
• Patients should not drink or eat directly before or during a measurement, and they should avoid any
physical exertion.
• Clean the area where you are taking the temperature and remove any dirt, hairs or sweat before
moving the sensor
q
to the measuring position.
• Do not remove the thermometer from the measuring position until it has beeped to signal the end of
the reading.
• If the sensor
q
becomes dirty during or after a reading, clean it with a cotton bud dipped in cleaning
alcohol before putting the thermometer away.
• Always take the temperature in the same place, because the readings will vary in different
environments.
The thermometer has been clinically tested, and its safety and accuracy inspected and conrmed,
provided it is used in accordance with these instructions.
Change the unit of measure
You can measure the temperature in ° Celsius or in ° Fahrenheit. Please proceed as follows to select the
unit of measure:
1. The device has to be switched off.
2. Press the SCAN-button w for approx. 8 seconds until the meausrement unit appears, then release.
3. Press the SCAN-button w again to change the unit of measurement to either °C or °F.
Measuring the body temperature
1. Turn on the thermometer by pressing SCAN-button w .
2. Point the senor q in the middle of the patient’s forehead at a
distance between 15 mm and max. 50 mm.
If the patient’s forehead has hair, sweat or dirt on it, remove
this rst so that the reading is as accurate as possible.
3. Press the SCAN-button w and release after approx. 1
second. You will hear a beep and the body temperature will be
displayed in the display e.
4. If the measurement result is below 32°C, a “Lo” sign will be
displayed follow by 2 consecutive beep sound. If measurement
reading is above 37.8°C, there will be 6 consecutive beep sound. If reading above 42.2°C is record, a “Hi”
sign will be displayed followed by 2 consecutive beep sound.
5. The measurement result will automatically be saved. After approx. 60 seconds without any further use the
thermometer will switch off automatically to save battery power.
15-50mm
15-50mm15-50mm15-50mm
Recalling stored data
The MEDISANA infrared thermometer can store up to 32 results.
You can call up your stored data with press on the SCAN-button wfor 4 seconds. The memory slot
number will be shown in the display e , together with the last stored temperature reading. With each
further press on the SCAN-button w , you can call up the previous results (memory slots 1 to 32).
Error messages
Display Problem Solution
Temperature taken is higher than
42.2°C / 108°F
Temperature taken is lower than
32°C / 89.6°F
Sensor not welded
EEPROM is abnormal
Low power
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Replace the batteries.
Cleaning and maintenance
•
The sensor is the most delicate part of the MEDISANA Non-contact Infrared Thermometer.
Protect it from dirt and damage. Clean the sensor with a cotton bus dipped in warm water or 70%
isopropyl alcohol.
•
Do not immerse the thermometer in water or any other liquid. It is not watertight.
•
To clean the thermometer, use a soft cloth slightly dampened with mild soapy water or 70% isopropyl
alcohol. Do not let water get into the unit. Only use the unit again when completely dry.
•
Never use aggressive cleaning agents, thinners, benzine or tough brushes.
•
Take care not to scratch the lens of the sensor, the display or the housing.
•
Do not use or store the unit in an environment where the ambient temperature or humidity is too high
or too low (see operating conditions in the “Technical specications” section), in direct sunshine, in
the vicinity of static electricity or in a dusty environment.
•
Remove the batteries if you do not wish to use the unit for an extended period of time.
Otherwise there is a danger that the batteries may leak.
•
If the thermometer is used as described in these instructions, no regular maintenance or calibration
is required.
Disposal
This product must not be disposed of together with domestic waste. All users are obliged to
hand in all electrical or electronic devices, regardless of whether or not they contain toxic
substances, at a municipal or commercial collection point so that they can be disposed of in
an environmentally acceptable manner. Please remove the batteries before disposing of the
device/unit. Do not dispose of old batteries with your household waste, but at a bettery
collection station at a recycling site or in a shop. Consult your municipal authority or your dealer for
information about disposal.
Technical specications
Name and model:
Display system:
Power supply
Measuring range:
Accuracy of measurement
(laboratory reading)
Display resolution
Memory capacity:
Auto. switch-off:
Operating temperature:
Storage/transport temperature:
Dimensions
Weight
Article no.:
EAN code:
MEDISANA Non-contact Infrared Thermometer TM 715
Digital display (LCD)
3V=, 2 x 1.5V batteries (type LR03, AAA)
32.0°C-42.2°C (89.6°F - 108°F)
±0.3°C(32.0°C ~ 42.2°C)
±0.5°F(89.6°F ~ 108°F) other range.
0.1°C (0.2°F)
up to 32 readings
approx. 1 minute after the last measurement
16°C-35°C(60.8°F - 95°F), rel. humidity of 15%-80%
-20°C-+55°C(-4°F - 131°F), rel. humidity of 15%-93%
approx. 144 x 101 x 36 mm
approx. 88 g (without batteries)
48615
40155 88 48615 9
In accordance with our policy of continual product improvement, we reserve the right to make
technical and optical changes without notice.
The unit is designed for home use only. For commercial use, a metrological inspection must
be carried out once every year. This calibration will be charged for and can be carried out by an
appropriate authority or an authorised service centre - in accordance with the regulations for users of
medical equipment.
Warranty and repair terms
Please contact your dealer or the service centre in case of a claim under the warranty, If you have to
return the unit, please enclose a copy of your receipt and state what the defect is.
The following warranty terms apply:
1. The warranty period for MEDISANA products is 3 years from date of purchase. In case of a
warranty claim, the date of purchase has to be proven by means of the sales receipt or invoice.
2. Defects in material or workmanship will be removed free of charge within the warranty period.
3. Repairs under warranty do not extend the warranty period either for the unit or for the replacement
parts.
4. The following is excluded under the warranty:
a . All damage which has arisen due to improper treatment, e.g. nonobservance of the user
instructions.
b . All damage which is due to repairs or tampering by the customer or unauthorised third parties.
c. Damage which has arisen during transport from the manufacturer to the consumer or during
transport to the service centre.
d. Accessories which are subject to normal wear and tear.
5. Liability for direct or indirect consequential losses caused by the unit are excluded even if the
damage to the unit is accepted as a warranty claim.
0123
0123
q w
e r
Error messages
Display Problem Solution
The temperature of the measuring
environment is too high.
The temperature of the measuring
environment is too low.
Decrease the temperature of the environment, keep
it within 16°C-35°C.
Increase the temperature of the environment, keep it
within 16°C-35°C.
0123
IP22
°F
°C
Explanation of symbols
IMPORTANT
Non-observance of these instructions can result in serious injury or damage to
the device.
WARNING
These warning note must be observed to prevent any injury to the user.
CAUTION
These notes must be observed to prevent any damage to the device.
NOTE
These notes give you useful additional information on the installation and
operation.
Device classication: type BF
LOT number
Manufacturer
Production date
Conforms to essential requirements of the Medical Device Directive 93/42/EEC.
Authorized Representative in European Community
The device should not be used after the end if the shown or the day
Protected against solid foreign objects of 12.5mm diameter and greater.
Protected against vertical falling water drops when the device is tilted up to 15°
Non-contact Infrared Thermometer TM 715
Instruction manual
48615_TM 715_manual_GB-TR_202011_L4
GB Safety Instructions
Important Information! Retain for future use! Read the instruction manual
carefully before using this device, especially the safety instructions, and keep the
instruction manual for future use, Should you give this device to another person,
it is vital that you also pass on these instructions for use.
Intended use:
The MEDISANA Non-contact Infrared Thermometer TM 715 is suitable to measure the body temperature of
humans. The measurement is carried out contact-free on the forehead.
Additionally the thermometer is suitable to measure the temperature of objects in the range of 0°C to 100°C.
• Only use the unit for the specic purpose described in the instruction manual. Any misuse will void the warranty.
• The unit is not designer for commercial use.
• Using this thermometer is no substitute for consulting a doctor. Consult your doctor in any case, before you start
a medicamentous treatment.
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before measuring
the temperature. Do not take a measurement within 30 minutes after physical exercise or after having a bath.
• This device is not designed to be used by persons(including children) with limited physical, sensory or mental
abilities, or by persons with insufcient experience and/or knowledge, unless under observation by a person
responsible for their safety, or unless they have been instructed in the use of the device.
• Children must be supervised to ensure that they do not play with the device.
• The temperature in the forehead and temple area differs from the internal temperature, which is taken orally or
rectally. Vasoconstriction, and effect which constricts the blood vessels and cools the skin, can occur during the
early stages of a fever. In this case, the temperature measured by the Non-contact Infrared Thermometer
TM 715 may be unusually low. If the measurement therefore does not match the patient’s own perception or is
unusually low, repeat the measurement every 15 minutes. As a reference, you can also measure the internal
body temperature using a conventional oral or rectal thermometer.
• It is recommended to perform at least 3 measurements with at least 1 minute interval. If the readings are
different; accept the highest value as reference value.
• A control measurement using a conventional thermometer is recommended in the following cases:
1. If the reading is surprisingly low
2. For new-born infants up to 100 days old
3. For children under three years of age who have a weakened immune system or who react unusually in the
presence or absence of fever
4. If you are using the thermometer for the rst time or want to familiarise yourself with it
• Babies’ skin reacts very quickly to the ambient temperature. Therefore, do not take their temperature with the
Non-contact Infrared Thermometer TM 715 during or after breastfeeding, because the skin temperature may
then be lower than the internal body temperature.
• There are no absolute body temperature standards. Keep record of your personal readings to allow your doctor
to judge if a medical treatment is necessary or not.
• Do not change the construction of the device and do not attempt to repair the unit yourself if a fault occurs or
the unit is damaged, as this will void the warranty. Contact your dealer and only have repairs carried out by
authorized service partners.
• Do not use the thermometer if it is damaged.
• Do not open up the device. It contains small parts which might be swallowed by children.
• Do not use the thermometer in damp environments.
• Do not immerse the thermometer in water or other liquids. It is not watertight.
• The sensor should be cleaned after each use, see the instructions in Cleaning and maintenance.
• Avoid direct nger contact with the sensor.
• Do not shake or tap the thermometer. Do not drop it.
• Protect the device from direct sunlight, extremely high or low temperatures, dirt and dust.
• If the thermometer is not going to be used for a long period, remove the batteries.
Unit and controls
Sensor
Scan-button
Illuminated LCD display
Battery compartment cover
Measurement of forehead temperature
°F Fahrenheit
°C Celsius
Temperature display
Memory display
Battery exchange symbole
q
w
e
r
t
y
u
i
o
a
Items supplied and packaging
Please check rst of all that the device is complete and is not damaged in any way. If in doubt, do not use it.
Send it to a service point.
The following parts are included:
•
1 MEDISANA Non-contact Infrared Thermometer TM 715
•
2 Batteries (AAA type, LR03) 1.5V
•
1 Instruction manual
The packaging can be reused or recycled. Please dispose properly of any packaging material no longer
required. If you notice any transport damage during unpacking, please contact your dealer without delay.
WARNING
Please ensure that polythene packing is kept away from the reach of children!
Risk of suffocation!
Taking a temperature reading – quickly and accurately!
The MEDISANA Non-contact Infrared Thermometer allows
precise, contact-free (approx. 1.5 to 5 cm distance) measurement
of body temperature. The temperature is taken above the
eye-brow between the forehead and the temple. The value
of the energy radiated there is measured and converted to a
temperature value. The reading is displayed within a few seconds.
The enables you, for example, to take babies’ temperature without
disturbing their sleep.
Getting started: Removing / Inserting batteries
For the use resp. if the battery symbol appears in the
display after a certain period of use, you must insert new batteries
before taking another measurement. Use two new 1.5 V batteries
(LR03, AAA).
Removal: Slide the lid of the battery compartment cover r
downwards as shown. Take out the batteries.
Insertion: Put in two new 1.5V-batteries (AAA, LR03). Make
sure the batteries are the right way around. Put the battery
compartment cover back on and move it upwards until it locks into
position.
WARNING
BATTERY SAFETY INFORMATION
•
Do not disassemble batteries!
•
Clean the battery and device contacts if necessary before putting in the batteries!
•
Remove discharged batteries from the device immediately!
•
Increased risk of leakage, avoid contact with skin, eyes and mucous membranes!
If battery acid comes in contact with any of these parts, rinse the affected area with copious
amounts of fresh water and seek medical attention immediately!
•
If a battery has been swallowed seek medical attention immediately!
•
Replace all of the batteries simultaneously!
•
Only replace with batteries of the same type, never use different types of batteries together or
used batteries with new ones!
•
Insert the batteries correctly, observing the polarity!
•
Keep the battery compartment well sealed!
•
Remove the batteries from the device if it is not going to be used for an extended period!
•
Keep batteries out of children’s reach!
•
Do not attempt to recharge these batteries! There is a danger of explosion!
•
Do not short circuit! There is a danger of explosion!
•
Do not throw into a re! There is a danger of explosion!
•
Keep unused batteries in their packaging away from metal objects in order to prevent short
circuiting!
•
Do not throw used batteries into the household refuse; put them in a hazardous waste container
or take them to a battery collection point, at the shop where they were purchased!
Before use
NOTES
For the most accurate reading:
• The thermometer and the patient must remain in a stable environment for at least 30 minutes before
measuring the temperature.
• Do not take a baby’s temperature during or directly after breastfeeding.
• Do not use the thermometer in damp environments.
• Patients should not drink or eat directly before or during a measurement, and they should avoid any
physical exertion.
• Clean the area where you are taking the temperature and remove any dirt, hairs or sweat before
moving the sensor
q
to the measuring position.
• Do not remove the thermometer from the measuring position until it has beeped to signal the end of
the reading.
• If the sensor
q
becomes dirty during or after a reading, clean it with a cotton bud dipped in cleaning
alcohol before putting the thermometer away.
• Always take the temperature in the same place, because the readings will vary in different
environments.
The thermometer has been clinically tested, and its safety and accuracy inspected and conrmed,
provided it is used in accordance with these instructions.
Change the unit of measure
You can measure the temperature in ° Celsius or in ° Fahrenheit. Please proceed as follows to select the
unit of measure:
1. The device has to be switched off.
2. Press the SCAN-button w for approx. 8 seconds until the meausrement unit appears, then release.
3. Press the SCAN-button w again to change the unit of measurement to either °C or °F.
Measuring the body temperature
1. Turn on the thermometer by pressing SCAN-button w .
2. Point the senor q in the middle of the patient’s forehead at a
distance between 15 mm and max. 50 mm.
If the patient’s forehead has hair, sweat or dirt on it, remove
this rst so that the reading is as accurate as possible.
3. Press the SCAN-button w and release after approx. 1
second. You will hear a beep and the body temperature will be
displayed in the display e.
4. If the measurement result is below 32°C, a “Lo” sign will be
displayed follow by 2 consecutive beep sound. If measurement
reading is above 37.8°C, there will be 6 consecutive beep sound. If reading above 42.2°C is record, a “Hi”
sign will be displayed followed by 2 consecutive beep sound.
5. The measurement result will automatically be saved. After approx. 60 seconds without any further use the
thermometer will switch off automatically to save battery power.
15-50mm
15-50mm15-50mm15-50mm
Recalling stored data
The MEDISANA infrared thermometer can store up to 32 results.
You can call up your stored data with press on the SCAN-button wfor 4 seconds. The memory slot
number will be shown in the display e , together with the last stored temperature reading. With each
further press on the SCAN-button w , you can call up the previous results (memory slots 1 to 32).
Error messages
Display Problem Solution
Temperature taken is higher than
42.2°C / 108°F
Temperature taken is lower than
32°C / 89.6°F
Sensor not welded
EEPROM is abnormal
Low power
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Operate the thermometer only between the specied
temperature ranges. In the event of a repeated error
message, contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Contact your retailer or Customer Services.
Replace the batteries.
Cleaning and maintenance
•
The sensor is the most delicate part of the MEDISANA Non-contact Infrared Thermometer.
Protect it from dirt and damage. Clean the sensor with a cotton bus dipped in warm water or 70%
isopropyl alcohol.
•
Do not immerse the thermometer in water or any other liquid. It is not watertight.
•
To clean the thermometer, use a soft cloth slightly dampened with mild soapy water or 70% isopropyl
alcohol. Do not let water get into the unit. Only use the unit again when completely dry.
•
Never use aggressive cleaning agents, thinners, benzine or tough brushes.
•
Take care not to scratch the lens of the sensor, the display or the housing.
•
Do not use or store the unit in an environment where the ambient temperature or humidity is too high
or too low (see operating conditions in the “Technical specications” section), in direct sunshine, in
the vicinity of static electricity or in a dusty environment.
•
Remove the batteries if you do not wish to use the unit for an extended period of time.
Otherwise there is a danger that the batteries may leak.
•
If the thermometer is used as described in these instructions, no regular maintenance or calibration
is required.
Disposal
This product must not be disposed of together with domestic waste. All users are obliged to
hand in all electrical or electronic devices, regardless of whether or not they contain toxic
substances, at a municipal or commercial collection point so that they can be disposed of in
an environmentally acceptable manner. Please remove the batteries before disposing of the
device/unit. Do not dispose of old batteries with your household waste, but at a bettery
collection station at a recycling site or in a shop. Consult your municipal authority or your dealer for
information about disposal.
Technical specications
Name and model:
Display system:
Power supply
Measuring range:
Accuracy of measurement
(laboratory reading)
Display resolution
Memory capacity:
Auto. switch-off:
Operating temperature:
Storage/transport temperature:
Dimensions
Weight
Article no.:
EAN code:
MEDISANA Non-contact Infrared Thermometer TM 715
Digital display (LCD)
3V=, 2 x 1.5V batteries (type LR03, AAA)
32.0°C-42.2°C (89.6°F - 108°F)
±0.3°C(32.0°C ~ 42.2°C)
±0.5°F(89.6°F ~ 108°F) other range.
0.1°C (0.2°F)
up to 32 readings
approx. 1 minute after the last measurement
16°C-35°C(60.8°F - 95°F), rel. humidity of 15%-80%
-20°C-+55°C(-4°F - 131°F), rel. humidity of 15%-93%
approx. 144 x 101 x 36 mm
approx. 88 g (without batteries)
48615
40155 88 48615 9
In accordance with our policy of continual product improvement, we reserve the right to make
technical and optical changes without notice.
The unit is designed for home use only. For commercial use, a metrological inspection must
be carried out once every year. This calibration will be charged for and can be carried out by an
appropriate authority or an authorised service centre - in accordance with the regulations for users of
medical equipment.
Warranty and repair terms
Please contact your dealer or the service centre in case of a claim under the warranty, If you have to
return the unit, please enclose a copy of your receipt and state what the defect is.
The following warranty terms apply:
1. The warranty period for MEDISANA products is 3 years from date of purchase. In case of a
warranty claim, the date of purchase has to be proven by means of the sales receipt or invoice.
2. Defects in material or workmanship will be removed free of charge within the warranty period.
3. Repairs under warranty do not extend the warranty period either for the unit or for the replacement
parts.
4. The following is excluded under the warranty:
a . All damage which has arisen due to improper treatment, e.g. nonobservance of the user
instructions.
b . All damage which is due to repairs or tampering by the customer or unauthorised third parties.
c. Damage which has arisen during transport from the manufacturer to the consumer or during
transport to the service centre.
d. Accessories which are subject to normal wear and tear.
5. Liability for direct or indirect consequential losses caused by the unit are excluded even if the
damage to the unit is accepted as a warranty claim.
0123
0123
q w
e r
Error messages
Display Problem Solution
The temperature of the measuring
environment is too high.
The temperature of the measuring
environment is too low.
Decrease the temperature of the environment, keep
it within 16°C-35°C.
Increase the temperature of the environment, keep it
within 16°C-35°C.
0123
IP22
Table of contents
Other Medisana Thermometer manuals
Medisana
Medisana ThermoDock User manual
Medisana
Medisana 48618 User manual
Medisana
Medisana 77055 User manual
Medisana
Medisana 99293 User manual
Medisana
Medisana 48620 User manual
Medisana
Medisana FTO 76072 User manual
Medisana
Medisana FTC User manual
Medisana
Medisana TM 700 User manual
Medisana
Medisana FTD User manual
Medisana
Medisana TM-60E User manual
Medisana
Medisana FTG User manual
Medisana
Medisana ThermoDock User manual
Medisana
Medisana FTD User manual
Medisana
Medisana NCT User manual
Medisana
Medisana FTF User manual
Medisana
Medisana FTC Thermometer User manual
Medisana
Medisana FTO 76073 User manual
Medisana
Medisana 76120 FTN User manual
Medisana
Medisana TM 750 User manual
