Members Mark BGK00523-4SC Owner's manual

THIS ASSEMBLY MANUAL CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Page 1
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Assembly Instructions & User's Manual
for
Members Mark Brexley 4pc Seating Set
Item Number: 990018738
Model Number: BGK00523-4SC
Customer Assistance : 1-800-416-3511
or Email: [email protected]
(spare/replacement parts)

Quality Statement.............................................................3
Important Safety Information.............................................3
Before Assembly..............................................................3
Package Contents............................................................4
Product Information..........................................................5
Components....................................................................6
Hardware.........................................................................6
Tools...............................................................................6
Step1–Step7..............................................................7-9
Care & Use and Storage Instructions.................................10
Warranty Information.......................................................10
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 2
Table of Contents

Before Assembly
Important Safety Information
Please read all instructions carefully before assembling this furniture.
For your safety, assembly by two or more adults is strongly recommended.
Use only vendor-supplied hardware to assemble this item. Using unauthorized
hardware could jeopardize the structural integrity of the item.
Hardware may loosen overtime. Periodically check that all connections are tight.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 3
Quality Statement
Remove all parts and hardware from the box. Place all items on a carpeted or
scratch-free work surface, as this will avoid damaging parts during assembly.
The shipping box can provide an ideal work surface if none is available.
Use the components and hardware lists below to identify, inventory and
separate each of the hardware and components included.
To avoid accidentally discarding small components or hardware, do not dispose
of any packaging or contents of the shipping carton until assembly is complete.
DO NOT USE power tools unless it is explicitly identified in this manual as
required for use during assembly. Power tools can damage the fasteners,
hardware and/or components.
Do not fully tighten all fasteners / screws until all parts are in place. Failure to
follow these instructions may cause the fasteners / screws to misalign during
assembly.

Need Assistance? Visit us at: samsclub.com/membersmarkhelp
1Set / 2Ctn
Box1of2:
Box2of2:
Component QuantityDescription
A
B
C
Swivel Glider
Sofa
Furniture Cover
2
1
1
Component QuantityDescription
A
B
C
D
Firepit Table Base
Fire Ices
1
AB
1
AC
B
Page 4
Package Contents
4
C
D
1
Burner Cover
Firepit Table Top

Need Assistance? Visit us at: samsclub.com/membersmarkhelp
B
A
Description Dimensions
Part No.
BGK00523
Chair 250lb Y
A.Foot Cap-1
FC0768 N/A N/A Y
Description Dimensions
Part No.
BGK00506Sofa 250lb per seat,
total 750lb Y
A.Foot Cap-1
FC0607 N/A N/A Y
Description Dimensions
Part No.
ARY05100
Firepit Table N
A.Foot Cap-1
FC0553 N/A N/A Y
B.Foot Cap-2
FC0245 N/A N/A Y
A
A
N/A
Page 5
Product information
Weight
Capacity
Factory
Assembly
Weight
Capacity
Factory
Assembly
Weight
Capacity
Factory
Assembly
Description Part No.
PCD2110H Chair's Cover
Sofa's Cover
Fire Pit's
Cover
PCD2201H
PCD2202H
32.5"D*30.5"W*27.5"H
32.5"Dx90"Wx27.5"H
26.75"Dx59.75"Wx24.5"H

Components
A. FIRE PIT TABLE TOP
Part No. FP3856
Qty 1
B FIRE PIT TABLE BASE
Part No.
Qty 1
.
FP3857
C.
FP3858
BURNER COVER
Part No.
Qty 1
D. BURNER PAN PROTECTIVE
RING
Part No.FP3859
Qty 1
E.
FP2147
FIRE ICE
Part No.
Qty 1
Page 6
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Hardware
Tools
(H18)
HEX BOLT DRIVER
Qty:
PART NO:HW0006
1
(H17)
HEX BOLT DRIVER
HW09
Qty:
PART NO: 00
1
(H2)
(FACTORY ASSEMBLY)GAS VALVE
PART NO: FP2330
Qty: 1
(H3)
(FACTORY ASSEMBLY)
THERMOCOUPLE
PART NO: FP2331
Qty: 1
(H4)
(FACTORY ASSEMBLY)
FLEX CONNECTOR
PART NO: FP2332
Qty: 1
(H5)
(FACTORY ASSEMBLY)
ELECTRODE
PART NO: FP3344
Qty: 1
(H6)
(FACTORY ASSEMBLY)
IGNITION MODULE
PART NO: FP2334
Qty: 1
(H7)
(FACTORY ASSEMBLY)
Qty:
LP REGULATOR HOSE
PART NO: FP2250
1
(H8)
(FACTORY ASSEMBLY)
Qty: 2
LP TANK RETAINING KNOB
PART NO:FP0585
(H9)
PROPANE ORIFICE
PART NO: FP2205
1
(FACTORY ASSEMBLY)
Qty:
(H1)
CONTROL KNOB
PART NO: FP2329
Qty: 1
(FACTORY ASSEMBLY)
(H10)
M4 BOLT
Qty: 2
(FACTORY ASSEMBLY)
PART NO:HW0898
(H13)
“AA” BATTERY(1.5V)
Qty:
PART NO: HW0905
1
(H14)
AIR SHUTTER
PART NO: FP1922
1Qty:
(H15)
NATURAL GAS ORIFICE
PART NO: FP1919
1Qty:
(H12)
Qty:
Ø20 X Ø6.5 X 2.0 MM WASHER
PART NO:
4
HW0594
(H16)
1/4”X20MMBOLT
Qty:
PART NO:HW0802
4
(H11)
ORIFICE HOLDER
Qty:
(FACTORY ASSEMBLY)
PART NO: FP3573
1

Step 1
Step 2
Hand tighten only 2-3 turns.
outer carton
(H16)
1/4"X20MMBOLT
Qty: 4
(H12)
Qty: 4
Ø20XØ6.5X2.0MM
WASHER
(H18)
Qty: 1
HEX BOLT DRIVER
H18
There are two factory assembled M4 screws in the firepan/burner assembly. Remove
those two screws in order to remove the burner pan protective ring.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Step1-Step7
Page 7
H16
H12

NOTE: Bolts must be
FULLY tightened.
IGNITION WELL
BURNER PAN
Place the burner pan protective ring, into the burner as shown in the . Secure the
burner pan protective ring to the burner pan by using two M4 screws.
diagram
Place the firepit table in its final position. There must be a minimum of 24 inches of
clearance from the side of the table top to any combustible walls.
(H10)
M4 BOLT
Qty: 2
(H17)
HEX BOLT DRIVER
Qty: 1
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Pour ALL of the fire ice into the burner pan. The burner MUST be completely covered to
ensure the appliance functions properly and safely. Remove any fire ice on top of the
ignition well.
Step 3
Step 4
Step 5
Page 8
H17 H10

Open the door and place the LP tank in the bottom frame. Connect the regulator. Turn the
black handle clockwise to tighten. Turn the handle counterclockwise to remove. The hose
must point down. Open the control door and check that the valve is turned all the way
clockwise to the “OFF” position. Open the tank valve. Apply a solution of soapy water to
the tank-regulator connection and to the valve-hose connection to check for leaks. If soap
bubbles continue to form, the connection has a leak. If a leak is found, close the tank valve
and tighten all connections. NEVER USE A FLAME TO CHECK FOR LEAKS.
Tighten 2 the threaded knobs found on the tank tray so that the LP tank cannot move from
side to side. Do not remove the plastic cap from the end of the threaded section.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Step 6
Step 7
Page 9

CARE AND MAINTENANCE
FRAMES
FABRICS (CUSHIONS/SLINGS)
STRAPS
CERAMIC TILE
Cleaning
Maintenance
Cleaning -
Maintenance
Cleaning -
Maintenance -
- Use mild soap and warm water. Do not use abrasive materials, cleaners, or bleach
products. Rinse with clean water and dry thoroughly.
- Periodically clean and dry thoroughly. Be sure to drain any water accumulated
inside the frames. To thoroughly drain frames, remove foot caps and tilt the frames, if necessary, to
remove all water. This is critical. Water allowed to accumulate inside the frames and then
exposed to sub-freezing temperatures can cause damage to the frame tubing. Always clean,
drain, and dry thoroughly before storing for the winter. For best results, always store or cover your
furniture when not in use. We recommend commercially available outdoor furniture covers. Any
small nicks or scratches can be covered with a light application of touch-up paint.
** When cleaning or moving large or heavy items, always have two people work together. Never
drag furniture.
Wipe minor spills immediately. Clean with mild soap, warm clean water, and a soft
cloth. Do not use abrasive materials, cleaners, or bleach products. Although fabric has been
treated to resist stains, occasional use of commercially available fabric cleaners may be
necessary. Follow manufacturer's instructions.
- The best way to maintain the beauty of cushions and slings is to store them in a dry
area and out of the elements when not in use or cover with commercially available outdoor
furniture covers.
Furniture covers are a great way to protect your set from harsh elements of weather and UV light.
However, it is important to ensure furniture and covers are free of moisture and debris before
covering. It is also necessary to promptly uncover furniture after rain and during periods of high
humidity to prevent moisture build up. Failure to do so can lead to permanent surface and finish
damage.
Wash frequently with mild soap, warm water, and a soft cloth. Rinse thoroughly with
warm, clean water. Do not use abrasive materials, cleaners, or bleach products.
Periodic application of commercially available vinyl cleaners and vinyl protectors will
enhance the look and prolong the life of straps. If your strap chair has cushions, make sure any
vinyl protectors applied are completely dry before placing cushion back on the chair.
Use clean water and mild detergent or commercially available ceramic tile cleaners as necessary.
Do not use abrasive materials or cleansers as they may scratch the surface of the tiles. Dry with
soft cloth. Do not use commercially available ceramic tile cleaners on table frame.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Care & Use Instructions
Warranty Information
This product component has a 5 year guarantee against defects in material and/or workmanship. If
you have any questions regarding the warranty or spare / replacement parts, please call our toll-
free number or email us at1-800-416-3511 [email protected]
NOTE: Please consider recycling all applicable packaging material.
Page 10