Members Mark L-DN1388SAL-A User manual

Fairbanks 3pc Bar Set-Bar

Item# L-DN1388SAL-A

Congratulations on your purchase of Fairbanks 3pc Bar Set-Bar. Our clear, easy to follow,

step-by-step instructions will guide you through the assembly process from start to finish.

WARNING:

Keep all children and pets away from assembly area. Children and pets should be supervised

when they are in the area of the Bar construction.

Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house,

overhanging branches, laundry line or electrical wires.

Some parts may contain sharp edges. When assembling and using this product, basic safety

precautions should always be followed to reduce the risk of personal injury and damage to the

product. Please read all instructions before assembly and use.

Check all bolts for tightness before use and periodically check and tighten bolts as necessary.

Prepare a carpet or something else to protect the table top during assembling.

Assemble on level ground.

For outdoor use only.

IMPORTANT

Please take time to read these instructions thoroughly and follow each step carefully for safe and

easy operation. Keep this manual for future reference.

We would like to hear from you with any comments or suggestions. In the continental U.S., you

can call us toll-free at 1-888-301-0332 from 8 a.m. to 5 p.m. CST Monday – Friday. You can also

send us an email using the feedback icon at SamsClub.com.



No. Description Qty

A Bar Top 1

B Cup Holder 6

C1 Side Panel 1 1

C2 Side Panel 2 1

D Front Panel 1

E1 Shelf 1 1

E2 Shelf 2 1

F1 Wine Rack Frame1 1

F2 Wine Rack Frame 2 1

G Connect Bar 4

No. Description Qty

AA Inner Hexagon Bolt M6x25 6

BB Outer Hexagon Bolt M6x15 10

CC Outer Hexagon Bolt M6x25 12

DD Flat Washer M6 36

EE Wrench M6 1

FF Screw M6x15 12

GG Hex Key M6 1

II Outer Hexagon Bolt M6x50 4

JJ Nut M6 4

Parts List

Hardware Pack



Step1:

Fig1: Attach Side Panel 1(C1) to Front Panel (D) by Inner Hexagon Bolt (AA) and

Flat Washer (DD) as show in Fig 1. Then attach Side Panel 2 (C2) to Front Panel

(D) in the same way.

Fig2: Put Shelf 1 (E1) between Side Panel 1(C1) and Side Panel 2 (C2). Fix Front

Panel (D) and Shelf 1 (E1) by Outer Hexagon Bolt (BB) and Flat Washer (DD) as

shown in Fig 2. Then fix Shelf 2 (E2) in the same way.

Fig3: Attach Side Panel 1(C1) to Shelf 1&2 (E1&2) by Outer Hexagon Bolt (CC)

and Flat Washer (DD) as shown in Fig 3. Then fix the other side in the same way.

Step2:

Fig4: Attach Connect Bar (G) to Wine Rack Frame 1 (F1) by Outer Hexagon Bolt (BB) and Flat Washer (DD)

as shown in Fig 4. Then attach Connect Bar (G) to Wine Rack Frame 2 (F2) in the same way.

(Note: the side of Wine Rack Frame with hole should be downward.)

Fig5: Put assembled wine rack on the left of Shelf 1 (E1) and fixed them by Outer Hexagon Bolt (CC) and

Flat Washer (DD) as shown in Fig 5.





Step4:

Fig7: Attach Cup Holder (B) and Bar Top (A) by Screw (FF) as shown in Fig 7.

(Note: the side of Cup Holder (B) with bigger bend should be outwards.)

Step3:

Fig 6: Turn over Bar Top (A) carefully and put it on a Carpet to protect the Table Top. Then fix Bar Top

(A) with Side Panel (C1&2) by Outer Hexagon Bolt (II), Flat Washe (DD) and Nut (JJ) as shown in Fig 6.



Turn up the bar. Your Bar is now ready for use.

Relax & Enjoy!

Care & Maintenance

Before using, clean the Bar completely with a soft dry towel. When not in use, wipe free of any dirt or

loose objects, wash with a mild solution of soap and water; rinse thoroughly and dry completely.

Do not use strong detergent or abrasive cleaners.

Limited Manufacturer’s Warranty:

This product carries a 1 year warranty against defects in workmanship and materials. We agree to

replace the defective product free of charge within the stated warranty period, when returned by the

original purchaser with proof of purchase. This product is not guaranteed against wear or breakage

due to misuse and/or abuse.

Exclusions:

Items used for commercial, contract, or other non-residential purposes, or items damaged due

to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or

rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for

warranty claims. Warranty is to the original purchaser and is non-transferable. Any

replacement of warranted items will be in the original style and color, or a similar style and

color if the original is unavailable or has been discontinued. As some states do not allow

exclusions or limitations on an implied warranty, the above exclusions and limitations may not

apply. This warranty gives you specific rights, and you may also have other rights, which vary

from state to state.

Fairbanks 3pc Bar Set-Chair

Item# L-DN1388SAL-A

Congratulations on your purchase of Fairbanks 3pc Bar Set-Chair. Our clear, easy to follow,

step-by-step instructions will guide you through the assembly process from start to finish.

WARNING:

Keep all children and pets away from assembly area. Children and pets should be supervised

when they are in the area of the Chair construction.

Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house,

overhanging branches, laundry line or electrical wires.

Some parts may contain sharp edges. When assembling and using this product, basic safety

precautions should always be followed to reduce the risk of personal injury and damage to the

product. Please read all instructions before assembly and use.

Check all bolts for tightness before use and periodically check and tighten bolts as necessary.

Assemble on level ground.

For outdoor use only.

IMPORTANT

Please take time to read these instructions thoroughly and follow each step carefully for safe and

easy operation. Keep this manual for future reference.

We would like to hear from you with any comments or suggestions. In the continental U.S., you

can call us toll-free at 1-888-301-0332 from 8 a.m. to 5 p.m. CST Monday – Friday. You can also

send us an email using the feedback icon at SamsClub.com.



No. Description Qty

A Seat Board 1

B Upper Connector 2

C Leg 2

D Down Connector 2

E Foot Mat

(pre-assembled) 2

No. Description Qty

AA Bolt M6x20 8

BB Bolt M6x35 4

CC Bolt M6x15 4

DD Flat Washer M6 8

EE Hex Key M6 1

FF Spring Washer M6 8

Step 1: Set the side with connector of Leg (C)

upwards. Insert Upper Connector (B) into Leg (C)

by following the arrow direction and fix them by

Bolt (CC), Spring Washer (FF) and Flat Washer

(DD) as shown in Fig 1. Attach Down Connector

(D) to Leg (C) by Bolt (AA) as shown in Fig 2.

Step 2: Rotate the assembled leg 180°. Insert

Upper Connector (B) into Leg (C) and fix them by

following Step 1.

Parts List

Hardware Pack



Care & Maintenance

Before using, clean the chair completely with a soft dry towel. When not in use, wipe free of any dirt

or loose objects, wash with a mild solution of soap and water; rinse thoroughly and dry completely.