Memphis Shades 2321-0052 User manual

Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
6. Install the windshield by placing the lower slots into the
lower mounting bushings. Slip the upper slots into the upper
mounting bushings and gently but firmly seat the slots into
place.
Lock the locking mechanism into place. (see figure 3 and 4)
7. Tighten all mounting bolts. Adjust the height, angle and
alignment of the windshield and tighten ALL bolts.
Note: This is a detachable windshield, ALWAYS make
sure the Locking Mechanism is Fully Engaged after in-
stalling the windshield! (see figure 4)
MOUNTING INSTRUCTIONS
2321-0052 SPORTSHIELD HONDA VT750 SHADOW AERO DETACHABLE
Figure 1 Figure 3
Figure 2
MEM8918 08-12-08
Read and follow these directions carefully.
During installation, make certain that when turning the
forks, there can be no interference with wiring or cables
AND, that the windshield can not hit the gas tank,
through the windshield's full range of adjustment.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.
Additional tools required, that are not included in this kit. ¼"
drive 8, 10, 13mm sockets and ratchet.
1.Cover gas tank and front fender with towels to avoid
damage during installation.
2. Install the windshield mounting plates onto the windshield,
using the bolts that are pre-assembled on the mounting plates.
The Santoprene grommets should be inserted through the
holes in the windshield so that the flat round part lies flat on
each side of the plastic. NOTE: Tabs will point in towards
headlight when properly installed. (see Figure 1)
3. On the Throttle side, locate the two bolts on the lower triple
tree that secure the chrome Fork Tins. Using a ratchet with an
8mm and 10mm socket, remove the two bolts.
4. Using the 6mm Allen wrench provided, remove the upper
triple tree pinch bolt.
5. Using a 10mm and 13mm
socket, loosely install the
lower bracket using the new bolts and washers
provided.
Next, slip the spacer behind the upper bracket mounting hole
and insert the new socket head cap screw with new washer
through the bracket, through the spacer and loosely tighten all
three bolts. (see figure 2) repeat steps 3 - 5 on the Clutch side.
Note: You will tighten these bolts after the windshield is in-
stalled on to the bushings.

MEM8918 08-12-08
MOUNTING INSTRUCTIONS
2321-0052 SPORTSHIELD HONDA VT750 SHADOW AERO DETACHABLE
31 6
5
7
8
9
10
2 4
6
BUSHING
ASSEMBLY
1. M1128
2. M1126
3. M1127
4. M1125
5. R300
6. M321
7. R301
8. R302
9. M320
10. M591
2321-0052 FATS/SLIMS KIT
CORRECT
Fully engaged
NOT CORRECT
BUSHING ASSEMBLY
1. Place lower slot into lower bushing. 2. Rotate top slot into
place. 3. & 4. Secure locking Mechanism.
123
Figure 3
4
A
B
C
C
D E
G - Lower
A. M505
B. R321
C. R323
D. R324
E. R318
F. M303
G. M306
F-Upper
Loosen Allen Bolt to adjust angle, then re-tighten Allen Bolt.
Figure 4
R322C/T
LATCH
ASSEMBLY
M591
PART #
R300
R302
4R323
DESCRIPTION
MOUNTING INSTRUCTIONS
M321 5/16" SS FLAT WASHER 4
M1126
RIGHT SPORTS PLATE HONDA AERO 1
M1125
LEFT SPORTS PLATE HONDA AERO
QTY.
1
1
M1127
LEFT BRACKET HONDA AERO 1
M1128
RIGHT BRACKET HONDA AERO 1
PART # DESCRIPTION QTY.
PINCH BOLT SPACER 2
8mm X 16MM SS HEX HEAD SCREW 2
BUSHING ASSEMBLY (2 PART)
1/4" SS FLAT WASHER 2
R301 6mm X 16MM SS HEX HEAD SCREW 2
M320 8mm X 45mm SOCKET HEAD CAP SCREW 2
4R324 #207 EPDM O-RING
1M311 6mm SHORT ARM ALLEN WRENCH
M310
M313 3/16" SHORT ARM ALLEN WRENCH 3/16" ALLEN WRENCH COVER
1
1
R322C CLUTCH SIDE LATCH ASSEMBLY
R322T THROTTLE SIDE LATCH ASSEMBLY
R334 6-32 X 3/8" FLAT HEAD SS SCREW
R326 SS SPRING
M306 1/4”-20 X 5/8” SOCKET HEAD CAP SCREW
M505 BUTTON NUT
4R318 1" SOCKET SHOULDER WASHER
M543 SANTOPRENE GROMMET
2M301 1/4"-20 X 3/8" SOCKET HEAD CAP SCREW
2
M504 SOCKET SHOULDER WASHER
M302 1/4"-20 X 1/2" SOCKET HEAD CAP SCREW
M8918 R321 1" INDENTED RECESSED SPACER
1
1
8
2
8
4
4
4
4
4M303 1/4"-20 X 3/4" SOCKET HEAD CAP SCREW
R329 SLOT NUT 2
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
you can also reach us at
[email protected]